Abstract: Adhesively bonded joints are preferred over the
conventional methods of joining such as riveting, welding, bolting
and soldering. Some of the main advantages of adhesive joints
compared to conventional joints are the ability to join dissimilar
materials and damage-sensitive materials, better stress distribution,
weight reduction, fabrication of complicated shapes, excellent
thermal and insulation properties, vibration response and enhanced
damping control, smoother aerodynamic surfaces and an
improvement in corrosion and fatigue resistance. This paper presents
the behavior of adhesively bonded joints subjected to combined
thermal loadings, using the numerical methods. The joint
configuration considers aluminum as central adherend with six
different outer adherends including aluminum, steel, titanium, boronepoxy,
unidirectional graphite-epoxy and cross-ply graphite-epoxy
and epoxy-based adhesives. Free expansion of the joint in x
direction was permitted and stresses in adhesive layer and interfaces
calculated for different adherends.
Abstract: Soil erosion is the most serious problem faced at
global and local level. So planning of soil conservation measures has
become prominent agenda in the view of water basin managers. To
plan for the soil conservation measures, the information on soil
erosion is essential. Universal Soil Loss Equation (USLE), Revised
Universal Soil Loss Equation 1 (RUSLE1or RUSLE) and Modified
Universal Soil Loss Equation (MUSLE), RUSLE 1.06, RUSLE1.06c,
RUSLE2 are most widely used conventional erosion estimation
methods. The essential drawbacks of USLE, RUSLE1 equations are
that they are based on average annual values of its parameters and so
their applicability to small temporal scale is questionable. Also these
equations do not estimate runoff generated soil erosion. So
applicability of these equations to estimate runoff generated soil
erosion is questionable. Data used in formation of USLE, RUSLE1
equations was plot data so its applicability at greater spatial scale
needs some scale correction factors to be induced. On the other hand
MUSLE is unsuitable for predicting sediment yield of small and large
events. Although the new revised forms of USLE like RUSLE 1.06,
RUSLE1.06c and RUSLE2 were land use independent and they have
almost cleared all the drawbacks in earlier versions like USLE and
RUSLE1, they are based on the regional data of specific area and
their applicability to other areas having different climate, soil, land
use is questionable. These conventional equations are applicable for
sheet and rill erosion and unable to predict gully erosion and spatial
pattern of rills. So the research was focused on development of nonconventional
(other than conventional) methods of soil erosion
estimation. When these non-conventional methods are combined with
GIS and RS, gives spatial distribution of soil erosion. In the present
paper the review of literature on non- conventional methods of soil
erosion estimation supported by GIS and RS is presented.
Abstract: Initial values of reference vectors have significant influence on recognition accuracy in LVQ. There are several existing techniques, such as SOM and k-means, for setting initial values of reference vectors, each of which has provided some positive results. However, those results are not sufficient for the improvement of recognition accuracy. This study proposes an ACO-used method for initializing reference vectors with an aim to achieve recognition accuracy higher than those obtained through conventional methods. Moreover, we will demonstrate the effectiveness of the proposed method by applying it to the wine data and English vowel data and comparing its results with those of conventional methods.
Abstract: Flood zoning studies have become more efficient in
recent years because of the availability of advanced computational
facilities and use of Geographic Information Systems (GIS). In the
present study, flood inundated areas were mapped using GIS for the
Dikrong river basin of Arunachal Pradesh, India, corresponding to
different return periods (2, 5, 25, 50, and 100 years). Further, the developed inundation maps corresponding to 25, 50, and 100 year return period floods were compared to corresponding maps
developed by conventional methods as reported in the Brahmaputra Board Master Plan for Dikrong basin. It was found that, the average
deviation of modelled flood inundation areas from reported map
inundation areas is below 5% (4.52%). Therefore, it can be said that
the modelled flood inundation areas matched satisfactorily with
reported map inundation areas. Hence, GIS techniques were proved to be successful in extracting the flood inundation extent in a time and cost effective manner for the remotely located hilly basin of Dikrong, where conducting conventional surveys is very difficult.
Abstract: One of the disadvantages of using OFDM is the larger
peak to averaged power ratio (PAPR) in its time domain signal. The
larger PAPR signal would course the fatal degradation of bit error
rate performance (BER) due to the inter-modulation noise in the nonlinear
channel. This paper proposes an improved DSI (Dummy
Sequence Insertion) method, which can achieve the better PAPR and
BER performances. The feature of proposed method is to optimize
the phase of each dummy sub-carrier so as to reduce the PAPR
performance by changing all predetermined phase coefficients in the
time domain signal, which is calculated for data sub-carriers and
dummy sub-carriers separately. To achieve the better PAPR
performance, this paper also proposes to employ the time-frequency
domain swapping algorithm for fine adjustment of phase coefficient
of the dummy subcarriers, which can achieve the less complexity of
processing and achieves the better PAPR and BER performances
than those for the conventional DSI method. This paper presents
various computer simulation results to verify the effectiveness of
proposed method as comparing with the conventional methods in the
non-linear channel.
Abstract: This paper considers a robust recovery of sparse frequencies
from partial phase-only measurements. With the proposed
method, sparse frequencies can be reconstructed, which makes full
use of the sparse distribution in the Fourier representation of the
complex-valued time signal. Simulation experiments illustrate the
proposed method-s advantages over conventional methods in both
noiseless and additive white Gaussian noise cases.
Abstract: In this paper, the problem of reducing switching
activity in on-chip buses at the stage of high-level synthesis is
considered, and a high-level low power bus binding based on dynamic
bit reordering is proposed. Whereas conventional methods use a fixed
bit ordering between variables within a bus, the proposed method
switches a bit ordering dynamically to obtain a switching activity
reduction. As a result, the proposed method finds a binding solution
with a smaller value of total switching activity (TSA). Experimental
result shows that the proposed method obtains a binding solution
having 12.0-34.9% smaller TSA compared with the conventional
methods.
Abstract: This paper proposes a novel frequency offset (FO) estimator for orthogonal frequency division multiplexing. Simplicity is most significant feature of this algorithm and can be repeated to achieve acceptable accuracy. Also fractional and integer part of FO is estimated jointly with use of the same algorithm. To do so, instead of using conventional algorithms that usually use correlation function, we use DFT of received signal. Therefore, complexity will be reduced and we can do synchronization procedure by the same hardware that is used to demodulate OFDM symbol. Finally, computer simulation shows that the accuracy of this method is better than other conventional methods.
Abstract: Particle Swarm Optimization (PSO) with elite PSO
parameters has been developed for power flow analysis under
practical constrained situations. Multiple solutions of the power flow
problem are useful in voltage stability assessment of power system.
A method of determination of multiple power flow solutions is
presented using a hybrid of Particle Swarm Optimization (PSO) and
local search technique. The unique and innovative learning factors of
the PSO algorithm are formulated depending upon the node power
mismatch values to be highly adaptive with the power flow problems.
The local search is applied on the pbest solution obtained by the PSO
algorithm in each iteration. The proposed algorithm performs reliably
and provides multiple solutions when applied on standard and illconditioned
systems. The test results show that the performances of
the proposed algorithm under critical conditions are better than the
conventional methods.
Abstract: It is known that if harmonic spectra are decreased, then
acoustic noise also decreased. Hence, this paper deals with a new
random switching strategy using DSP TMS320F2812 to decrease the
harmonics spectra of single phase switched reluctance motor. The
proposed method which combines random turn-on, turn-off angle
technique and random pulse width modulation technique is shown. A
harmonic spread factor (HSF) is used to evaluate the random
modulation scheme. In order to confirm the effectiveness of the new
method, the experimental results show that the harmonic intensity of
output voltage for the proposed method is better than that for
conventional methods.
Abstract: This paper describes a system-level SoC energy
consumption estimation method based on a dynamic behavior of
embedded software in the early stages of the SoC development. A
major problem of SOC development is development rework caused by
unreliable energy consumption estimation at the early stages. The
energy consumption of an SoC used in embedded systems is strongly
affected by the dynamic behavior of the software. At the early stages
of SoC development, modeling with a high level of abstraction is
required for both the dynamic behavior of the software, and the
behavior of the SoC. We estimate the energy consumption by a UML
model-based simulation. The proposed method is applied for an actual
embedded system in an MFP. The energy consumption estimation of
the SoC is more accurate than conventional methods and this proposed
method is promising to reduce the chance of development rework in
the SoC development. ∈