Abstract: A transient model for nozzle clogging has been developed and successfully validated against a laboratory experiment. Key steps of clogging are considered: transport of particles by turbulent flow towards the nozzle wall; interactions between fluid flow and nozzle wall, and the adhesion of the particle on the wall; the growth of the clog layer and its interaction with the flow. The current paper is to investigate the mesh (size and type) sensitivity of the model in both two and three dimensions. It is found that the algorithm for clog growth alone excluding the flow effect is insensitive to the mesh type and size, but the calculation including flow becomes sensitive to the mesh quality. The use of 2D meshes leads to overestimation of the clog growth because the 3D nature of flow in the boundary layer cannot be properly solved by 2D calculation. 3D simulation with tetrahedron mesh can also lead to an error estimation of the clog growth. A mesh-independent result can be achieved with hexahedral mesh, or at least with triangular prism (inflation layer) for near-wall regions.
Abstract: Population growth in cities has led to an increase in the infrastructures construction, including buildings and roadways. This aspect leads directly to the soils waterproofing. In turn, changes in precipitation patterns are developing into higher and more frequent intensities. Thus, these two conjugated aspects decrease the rainwater infiltration into soils and increase the volume of surface runoff. The practice of green and sustainable urban solutions has encouraged research in these areas. The porous asphalt pavement, as a green infrastructure, is part of practical solutions set to address urban challenges related to land use and adaptation to climate change. In this field, permeable pavements with porous asphalt mixtures (PA) have several advantages in terms of reducing the runoff generated by the floods. The porous structure of these pavements, compared to a conventional asphalt pavement, allows the rainwater infiltration in the subsoil, and consequently, the water quality improvement. This green infrastructure solution can be applied in cities, particularly in streets or parking lots to mitigate the floods effects. Over the years, the pores of these pavements can be filled by sediment, reducing their function in the rainwater infiltration. Thus, double layer porous asphalt (DLPA) was developed to mitigate the clogging effect and facilitate the water infiltration into the lower layers. This study intends to deepen the knowledge of the performance of DLPA when subjected to clogging. The experimental methodology consisted on four evaluation phases of the DLPA infiltration capacity submitted to three precipitation events (100, 200 and 300 mm/h) in each phase. The evaluation first phase determined the behavior after DLPA construction. In phases two and three, two 500 g/m2 clogging cycles were performed, totaling a 1000 g/m2 final simulation. Sand with gradation accented in fine particles was used as clogging material. In the last phase, the DLPA was subjected to simple sweeping and vacuuming maintenance. A precipitation simulator, type sprinkler, capable of simulating the real precipitation was developed for this purpose. The main conclusions show that the DLPA has the capacity to drain the water, even after two clogging cycles. The infiltration results of flows lead to an efficient performance of the DPLA in the surface runoff attenuation, since this was not observed in any of the evaluation phases, even at intensities of 200 and 300 mm/h, simulating intense precipitation events. The infiltration capacity under clogging conditions decreased about 7% on average in the three intensities relative to the initial performance that is after construction. However, this was restored when subjected to simple maintenance, recovering the DLPA hydraulic functionality. In summary, the study proved the efficacy of using a DLPA when it retains thicker surface sediments and limits the fine sediments entry to the remaining layers. At the same time, it is guaranteed the rainwater infiltration and the surface runoff reduction and is therefore a viable solution to put into practice in permeable pavements.
Abstract: Collection of storm water runoff and forcing it into the
groundwater is the need of the hour to sustain the ground water table.
However, the runoff entraps various types of sediments and other
floating objects whose removal are essential to avoid pollution of
ground water and blocking of pores of aquifer. However, it requires
regular cleaning and maintenance due to problem of clogging. To
evaluate the performance of filter system consisting of coarse sand
(CS), gravel (G) and pebble (P) layers, a laboratory experiment was
conducted in a rectangular column. The effect of variable thickness
of CS, G and P layers of the filtration unit of the recharge shaft on the
recharge rate and the sediment concentration of effluent water were
evaluated.
Medium sand (MS) of three particle sizes, viz. 0.150–0.300 mm
(T1), 0.300–0.425 mm (T2) and 0.425–0.600 mm of thickness 25 cm,
30 cm and 35 cm respectively in the top layer of the filter system and
having seven influent sediment concentrations of 250–3,000 mg/l
were used for experimental study. The performance was evaluated in
terms of recharge rates and clogging time. The results indicated that
100 % suspended solids were entrapped in the upper 10 cm layer of
MS, the recharge rates declined sharply for influent concentrations of
more than 1,000 mg/l. All treatments with higher thickness of MS
media indicated recharge rate slightly more than that of all treatment
with lower thickness of MS media respectively. The performance of
storm water infiltration systems was highly dependent on the
formation of a clogging layer at the filter. An empirical relationship
has been derived between recharge rates, inflow sediment load, size
of MS and thickness of MS with using MLR.
Abstract: In MANET, mobile nodes communicate with each
other using the wireless channel where transmission takes place with
significant interference. The wireless medium used in MANET is a
shared resource used by all the nodes available in MANET. Packet
reserving is one important resource management scheme which
controls the allocation of bandwidth among multiple flows through
node cooperation in MANET. This paper proposes packet reserving
and clogging control via Routing Aware Packet Reserving (RAPR)
framework in MANET. It mainly focuses the end-to-end routing
condition with maximal throughput. RAPR is complimentary system
where the packet reserving utilizes local routing information
available in each node. Path setup in RAPR estimates the security
level of the system, and symbolizes the end-to-end routing by
controlling the clogging. RAPR reaches the packet to the destination
with high probability ratio and minimal delay count. The standard
performance measures such as network security level,
communication overhead, end-to-end throughput, resource utilization
efficiency and delay measure are considered in this work. The results
reveals that the proposed packet reservation and clogging control via
Routing Aware Packet Reserving (RAPR) framework performs well
for the above said performance measures compare to the existing
methods.
Abstract: This paper deals with the issue of biomass and sorted
municipal waste gasification and cogeneration using hot-air turbo-set.
It brings description of designed pilot plant with electrical output 80
kWe. The generated gas is burned in secondary combustion chamber
located beyond the gas generator. Flue gas flows through the heat
exchanger where the compressed air is heated and consequently
brought to a micro turbine. Except description, this paper brings our
basic experiences from operating of pilot plant (operating parameters,
contributions, problems during operating, etc.). The principal
advantage of the given cycle is the fact that there is no contact
between the generated gas and the turbine. So there is no need for
costly and complicated gas cleaning which is the main source of
operating problems in direct use in combustion engines because the
content of impurities in the gas causes operation problems to the units
due to clogging and tarring of working surfaces of engines and
turbines, which may lead as far as serious damage to the equipment
under operation. Another merit is the compact container package
making installation of the facility easier or making it relatively more
mobile. We imagine, this solution of cogeneration from biomass or
waste can be suitable for small industrial or communal applications,
for low output cogeneration.
Abstract: In this work, the bioclogging of two soils with different granulometries is presented. The durability of the clogging is also studied under cycles of hydraulic head and under cycles of desaturation-resaturation. The studied materials present continuous grain size distributions. The first one corresponding to the "material 1” presents grain sizes between 0.4 and 4mm. The second material called "material 2" is composed of grains with size varying between 1 and 10mm. The results show that clogging occurs very quickly after the injection of nutrition and an outlet flow near to 0 is observed. The critical hydraulic head is equal to 0.76 for "material 1", and 0.076 for "material 2". The durability tests show a good resistance to unclogging under cycles of hydraulic head and desaturation-resaturation for the "material 1". Indeed, the flow after the cycles is very low. In contrast, "material 2", shows a very bad resistance, especially under the hydraulic head cycles. The resistance under the cycles of desaturation-resaturation is better but an important increase of the flow is observed. The difference of behavior is due to the granulometry of the materials. Indeed, the large grain size contributes to the reduction of the efficiency of the bioclogging treatment in this material.
Abstract: Microbial-induced calcite precipitation (MICP) is a
relatively green and sustainable soil improvement technique. It
utilizes biochemical process that exists naturally in soil to improve
engineering properties of soils. The calcite precipitation process is
uplifted by the mean of injecting higher concentration of urease
positive bacteria and reagents into the soil. The main objective of this
paper is to provide an overview of the factors affecting the MICP in
soil. Several factors were identified including nutrients, bacteria type,
geometric compatibility of bacteria, bacteria cell concentration,
fixation and distribution of bacteria in soil, temperature, reagents
concentration, pH, and injection method. These factors were found to
be essential for promoting successful MICP soil treatment.
Furthermore, a preliminary laboratory test was carried out to
investigate the potential application of the technique in improving the
shear strength and impermeability of a residual soil specimen. The
results showed that both shear strength and impermeability of
residual soil improved significantly upon MICP treatment. The
improvement increased with increasing soil density.
Abstract: Fluids are used for heat transfer in many engineering
equipments. Water, ethylene glycol and propylene glycol are some
of the common heat transfer fluids. Over the years, in an attempt to
reduce the size of the equipment and/or efficiency of the process,
various techniques have been employed to improve the heat transfer
rate of these fluids. Surface modification, use of inserts and
increased fluid velocity are some examples of heat transfer
enhancement techniques. Addition of milli or micro sized particles
to the heat transfer fluid is another way of improving heat transfer
rate. Though this looks simple, this method has practical problems
such as high pressure loss, clogging and erosion of the material of
construction. These problems can be overcome by using nanofluids,
which is a dispersion of nanosized particles in a base fluid.
Nanoparticles increase the thermal conductivity of the base fluid
manifold which in turn increases the heat transfer rate. In this work,
the heat transfer enhancement using aluminium oxide nanofluid has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: The paper deals with the analysis of triggering
conditions and evolution processes of piping phenomena, in relation
to both mechanical and hydraulic aspects. In particular, the aim of
the study is to predict slope instabilities triggered by piping,
analysing the conditions necessary for a flow failure to occur. Really,
the mechanical effect involved in the loads redistribution around the
pipe is coupled to the drainage process arising from higher
permeability of the pipe. If after the pipe formation, the drainage
goes prevented for pipe clogging, the porewater pressure increase can
lead to the failure or even the liquefaction, with a subsequent flow
slide. To simulate the piping evolution and to verify relevant stability
conditions, a iterative coupled modelling approach has been pointed
out. As example, the proposed tool has been applied to the Stava
Valley disaster (July, 1985), demonstrating that piping might be one
of triggering phenomena of the tailings dams collapse.