Abstract: Numerical studies on race car aerodynamics at wing
in ground effect have been carried out using a steady 3d, double
precision, pressure-based, and standard k-epsilon turbulence model.
Through various parametric analytical studies we have observed that
at a particular speed and ground clearance of the wings a favorable
negative lift was found high at a particular angle of attack for all the
physical models considered in this paper. The fact is that if the
ground clearance height to chord length (h/c) is too small, the
developing boundary layers from either side (the ground and the
lower surface of the wing) can interact, leading to an altered variation
of the aerodynamic characteristics at wing in ground effect. Therefore
a suitable ground clearance must be predicted throughout the racing
for a better performance of the race car, which obviously depends
upon the coupled effects of the topography, wing orientation with
respect to the ground, the incoming flow features and/or the race car
speed. We have concluded that for the design of high performance
and high speed race cars the adjustable wings capable to alter the
ground clearance and the angles of attack is the best design option for
any race car for racing safely with variable speeds.
Abstract: Nowadays, the importance of energy saving is clearance to everyone. By attention to increasing price of fuels and also the problems of environment pollutions, there are the most efforts for using fuels littler and more optimum in everywhere. This essay studies optimizing of gas consumption in gas-burner space heaters. In oven of each gas-burner space heaters there is two snags to prevent the hot air (the result of combustion of natural gas) to go out of oven of the gas-burner space heaters directly without delivering its heat to the space of favorite environment like a room. These snags cause a excess circulating that helps hot air deliver its heat to the space of favorite environment. It means the exhaust air temperature will be decreased then when there are no snags. This is the aim of this essay to use maximum potential energy of the natural gas to make heat. In this study, by the help of a finite volume software (FLUENT) consumption of the gas-burner space heaters is simulated and optimized. At the end of this writing, by comparing the results of software and experimental results, it will be proved the authenticity of this method.
Abstract: Verapamil has been shown to inhibit fentanyl uptake in vitro and is a potent P-glycoprotein inhibitor. Tissue partitioning of loperamide, a commercially available opioid, is closely controlled by the P-gp efflux transporter. The following studies were designed to evaluate the effect of opioids on verapamil partitioning in the lung and brain, in vivo. Opioid (fentanyl or loperamide) was administered by intravenous infusion to Sprague Dawley rats alone or in combination with verapamil and plasma, with lung and brain tissues were collected at 1, 5, 6, 8, 10 and 60 minutes. Drug dispositions were modeled by recirculatory pharmacokinetic models. Fentanyl slightly increased the verapamil lung (PL) partition coefficient yet decreased the brain (PB) partition coefficient. Furthermore, loperamide significantly increased PLand PB. Fentanyl reduced the verapamil volume of distribution (V1) and verapamil elimination clearance (ClE). Fentanyl decreased verapamil brain partitioning, yet increased verapamil lung partitioning. Also, loperamide increased lung and brain partitioning in vivo. These results suggest that verapamil and fentanyl may be substrates of an unidentified inward transporter in brain tissue and confirm that verapamil and loperamide are substrates of the efflux transporter P-gp.
Abstract: This paper presents a comparison of average outgoing
quality limit of the MCSP-2-C plan with MCSP-C when MCSP-2-C
has been developed from MCSP-C. The parameters used in MCSP-2-
C are: i (the clearance number), c (the acceptance number), m (the
number of conforming units to be found before allowing c nonconforming
units in the sampling inspection), f1 and f2 (the sampling
frequency at level 1 and 2, respectively). The average outgoing
quality limit (AOQL) values from two plans were compared and we
found that for all sets of i, r, and c values, MCSP-2-C gives higher
values than MCSP-C. For all sets of i, r, and c values, the average
outgoing quality values of MCSP-C and MCSP-2-C are similar when
p is low or high but is difference when p is moderate.
Abstract: In this paper, the trajectory tracking problem for carlike mobile robots have been studied. The system comprises of a leader and a follower robot. The purpose is to control the follower so that the leader-s trajectory is tracked with arbitrary desired clearance to avoid inter-robot collision while navigating in a terrain with obstacles. A set of artificial potential field functions is proposed using the Direct Method of Lyapunov for the avoidance of obstacles and attraction to their designated targets. Simulation results prove the efficiency of our control technique.
Abstract: Implementation of response surface methodology (RSM) was employed to study the effects of two factor (rubber clearance and round per minute) in brown rice peeling machine of The optimal BROKENS yield (19.02, average of three repeats),.The optimized composition derived from RSM regression was analyzed using Regression analysis and Analysis of Variance (ANOVA). At a significant level α = 0.05, the values of Regression coefficient, R 2 (adj)were 97.35 % and standard deviation were 1.09513. The independent variables are initial rubber clearance, and round per minute parameters namely. The investigating responses are final rubber clearance, and round per minute (RPM). The restriction of the optimization is the designated.
Abstract: Clearance in the joints of multibody mechanical
systems such as linkage mechanisms and robots is a main source of
vibration, and noise of the whole system, and wear of the joints
themselves. This clearance is an inevitable matter and cannot be
eliminated, since it allows the relative motion between joint
components and make them assemblage. This paper presents an
experimental verification of the obtained simulation results of a slider
– crank mechanism of one clearance revolute joint. The simulation
results are obtained with the aid of CAD and dynamic simulation
softwares, which is an effective method of simulation multibody
systems with clearance joints and have many advantages. The
comparison between both simulation and experimental results shows
that the simulation results are so close to the experimental ones which
proves the accuracy and efficiency of this method of modeling and
simulation of mechanical systems with clearance joints.
Abstract: This paper numerically investigates the effects of input
speed on the overall dynamic characteristics of a multi-body system
with differently located revolute clearance joints without friction. A
typical planar slider-crank mechanism is used as a demonstration case
in which the effects of the input speed on the dynamic performance
of the mechanism with a revolute clearance joint between the crank
and connecting rod, and between the connecting rod and slider are
separately investigated with comprehensive observations numerically
presented. It is observed that, changing the driving speed of a multibody
system makes the behavior of the system to change from
either periodic to chaotic, or chaotic to periodic depending on which
joint has clearance. The location of the clearance revolute joint and
the operating speed of a multi-body system play a crucial role in
predicting accurately the dynamic responses of the system. Therefore
the dynamic behavior of one clearance revolute joint cannot be used
as a general case for a mechanical system.
Abstract: Fuzzy logic approach is used in this study to predict
the tractive performance in terms of traction force, and motion
resistance for an intelligent air cushion track vehicle while it operates
in the swamp peat. The system is effective to control the intelligent
air –cushion system with measuring the vehicle traction force (TF),
motion resistance (MR), cushion clearance height (CH) and cushion
pressure (CP). Sinkage measuring sensor, magnetic switch, pressure
sensor, micro controller, control valves and battery are incorporated
with the Fuzzy logic system (FLS) to investigate experimentally the
TF, MR, CH, and CP. In this study, a comparison for tractive
performance of an intelligent air cushion track vehicle has been
performed with the results obtained from the predicted values of FLS
and experimental actual values. The mean relative error of actual and
predicted values from the FLS model on traction force, and total
motion resistance are found as 5.58 %, and 6.78 % respectively. For
all parameters, the relative error of predicted values are found to be
less than the acceptable limits. The goodness of fit of the prediction
values from the FLS model on TF, and MR are found as 0.90, and
0.98 respectively.
Abstract: In the present research, two nutraceuticals made from
red grape and walnut that showed previously to improve kidney
dysfunction were incorporated separately into functional foods' bread
made from barley and rice bran. The functional foods were evaluated
in rats in which chronic renal failure was induced through feeding
diet rich in adenine and phosphate (APD). The evaluation based on
assessing kidney function, oxidative stress, inflammatory biomarkers
and body weight gain. Results showed induction of chronic kidney
failure reflected in significant increase in plasma urea, creatinine,
malondialdehyde, tumor necrosis factor- α and low density
lipoprotein cholesterol along with significant reduction of plasma
albumin, and total antioxidant and creatinine clearance and body
weight gain on feeding APD compared to control healthy group.
Feeding the functional foods produced amelioration in the different
biochemical parameters and body weight gain indicating
improvement in kidney function.
Abstract: A personal estimate of a health risk may not
correspond to a scientific assessment of the health risk. Hence, there
is a need to investigate perceived health risks in the public. In this
study, a young, educated and healthy group of people from a tertiary
institute were questioned about their health concerns. Ethics
clearance was obtained and data was collected by means of a
questionnaire. 362 students participated in the study. Tobacco use,
heavy alcohol drinking, illicit drugs, unsafe sex and potential
carcinogens were perceived to be the five greatest threats to health in
this cohort. On the other hand natural health products,
unemployment, unmet contraceptive needs, family violence and
homelessness were felt to be the least perceived health risks.
Nutrition-related health risks as well as health risks due to physical
inactivity and obesity were not perceived as major health threats.
Such a study of health perceptions may guide health promotion
campaigns.
Abstract: This paper may be considered as combination of both pervasive computing and Differential GPS (global positioning satellite) which relates to control automatic traffic signals in such a
way as to pre-empt normal signal operation and permit lifesaving vehicles. Before knowing the arrival of the lifesaving vehicles from
the signal there is a chance of clearing the traffic. Traffic signal
preemption system includes a vehicle equipped with onboard computer system capable of capturing diagnostic information and
estimated location of the lifesaving vehicle using the information provided by GPS receiver connected to the onboard computer system
and transmitting the information-s using a wireless transmitter via a
wireless network. The fleet management system connected to a
wireless receiver is capable of receiving the information transmitted
by the lifesaving vehicle .A computer is also located at the
intersection uses corrected vehicle position, speed & direction
measurements, in conjunction with previously recorded data defining
approach routes to the intersection, to determine the optimum time to
switch a traffic light controller to preemption mode so that lifesaving
vehicles can pass safely. In case when the ambulance need to take a
“U" turn in a heavy traffic area we suggest a solution. Now we are
going to make use of computerized median which uses LINKED
BLOCKS (removable) to solve the above problem.
Abstract: A pressure-based implicit procedure to solve Navier-
Stokes equations on a nonorthogonal mesh with collocated finite
volume formulation is used to simulate flow around the smart and
conventional flaps of spoiler under the ground effect. Cantilever
beam with uniformly varying load with roller support at the free end
is considered for smart flaps. The boundedness criteria for this
procedure are determined from a Normalized Variable diagram
(NVD) scheme. The procedure incorporates es the k -ε eddyviscosity
turbulence model. The method is first validated against
experimental data. Then, the algorithm is applied for turbulent
aerodynamic flows around a spoiler section with smart and
conventional flaps for different attack angle, flap angle and ground
clearance where the results of two flaps are compared.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: A series of tests on cold-formed steel (CFS) wall plate system subjected to uplift force at the mid span of the wall plate is presented. The aim of the study was to study the behaviour and identify the modes of failure of CFS wall plate system. Two parameters were considered in these studies: 1) different dimension of U-bracket at the supports and 2) different sizes of lipped C-channel. The lipped C-channels used were C07508, C07512 and C10012. The dimensions of the leg of U-bracket were 50x35 mm and 50x60 mm respectively, where 25 mm clearance was provided to the connections for specimens with clearance. Results show that specimens with and without clearance experienced the same mode of failure. Failure began with the yielding of the connectors followed by distortional buckling of the wall plate. However, when C075 sections were used as wall plate, the system behaved differently. There was a large deformation in the wall plate and failure began in the distortional buckling of the wall plate followed by bearing of the connecting plates at the supports (U-bracket). The ultimate strength of the system also decreased dramatically when C075 sections were used.
Abstract: Simplified coupled engine block-crankshaft models
based on beam theory provide an efficient substitute to engine
simulation in the design process. These models require accurate
definition of the main bearing stiffness. In this paper, an investigation
of this stiffness is presented. The clearance effect is studied using a
smooth bearing model. It is manifested for low shaft displacement.
The hydrodynamic assessment model shows that the oil film has no
stiffness for low loads and it is infinitely rigid for important loads.
The deformation stiffness is determined using a suitable finite
elements model based on real CADs. As a result, a main bearing
behaviour law is proposed. This behaviour law takes into account the
clearance, the hydrodynamic sustention and the deformation stiffness.
It ensures properly the transition from the configuration low rigidity
to the configuration high rigidity.
Abstract: This paper presents an optimization of the hull
separation, i.e. transverse clearance. The main objective is to identify
the feasible speed ranges and find the optimum transverse clearance
considering the minimum wave-making resistance. The dimensions
and the weight of hardware systems installed in the catamaran
structured fuel cell powered USV (Unmanned Surface Vehicle) were
considered as constraints. As the CAE (Computer Aided Engineering)
platform FRIENDSHIP-Framework was used. The hull surface
modeling, DoE (Design of Experiment), Tangent search optimization,
tool integration and the process automation were performed by
FRIENDSHIP-Framework. The hydrodynamic result was evaluated
by XPAN the potential solver of SHIPFLOW.
Abstract: In the numerical solution of the forward dynamics of a
multibody system, the positions and velocities of the bodies in the
system are obtained first. With the information of the system state
variables at each time step, the internal and external forces acting on
the system are obtained by appropriate contact force models if the
continuous contact method is used instead of a discrete contact
method. The local deformation of the bodies in contact, represented
by penetration, is used to compute the contact force. The ability and
suitability with current cylindrical contact force models to describe
the contact between bodies with cylindrical geometries with
particular focus on internal contacting geometries involving low
clearances and high loads simultaneously is discussed in this paper.
A comparative assessment of the performance of each model under
analysis for different contact conditions, in particular for very
different penetration and clearance values, is presented. It is
demonstrated that some models represent a rough approximation to
describe the conformal contact between cylindrical geometries
because contact forces are underestimated.
Abstract: Fuzzy logic system (FLS) is used in this study to
predict the tractive performance in terms of traction force, and
motion resistance for an intelligent air cushion track vehicle while it
operates in the swamp peat. The system is effective to control the
intelligent air –cushion system with measuring the vehicle traction
force (TF), motion resistance (MR), cushion clearance height (CH)
and cushion pressure (CP). Ultrasonic displacement sensor, pull-in
solenoid electromagnetic switch, pressure control sensor, micro
controller, and battery pH sensor are incorporated with the Fuzzy
logic system to investigate experimentally the TF, MR, CH, and CP.
In this study, a comparison for tractive performance of an intelligent
air cushion track vehicle has been performed with the results obtained
from the predicted values of FLS and experimental actual values. The
mean relative error of actual and predicted values from the FLS
model on traction force, and total motion resistance are found as 5.58
%, and 6.78 % respectively. For all parameters, the relative error of
predicted values are found to be less than the acceptable limits. The
goodness of fit of the prediction values from the FLS model on TF,
and MR are found as 0.90, and 0.98 respectively.
Abstract: In this study the regional stability of a rotor system which is supported on rolling bearings with radial clearance is studied. The rotor is assumed to be rigid. Due to radial clearance of bearings and dynamic configuration of system, each rolling elements of bearings has the possibility to be in contact with both of the races (under compression) or lose its contact. As a result, this change in dynamic of the system makes it to be known as switching system which is a type of Hybrid systems. In this investigation by adopting Multiple Lyapunov Function theorem and using Hamiltonian function as a candidate Lyapunov function, the stability of the system is studied. The purpose of this study is to inspect the regional stability of rotor-roller bearing and rotor-ball bearing systems.