Abstract: In this paper, an overview of the radio over fiber (RoF) technology is provided. Obstacles for reducing the capital and operational expenses in the existing systems are discussed in various perspectives. Some possible RoF deployment scenarios for WiMAX
data transmission are proposed as a means for capital and operational
expenses reduction. IEEE 802.16a standard based end-to-end physical layer model is simulated including intensity modulated direct detection RoF technology. Finally the feasibility of RoF
technology to carry WiMAX signals between the base station and the
remote antenna units is demonstrated using the simulation results.
Abstract: In wireless and mobile communications, this progress
provides opportunities for introducing new standards and improving
existing services. Supporting multimedia traffic with wireless networks
quality of service (QoS). In this paper, a grey-fuzzy controller for radio
resource management (GF-RRM) is presented to maximize the number
of the served calls and QoS provision in wireless networks. In a
wireless network, the call arrival rate, the call duration and the
communication overhead between the base stations and the control
center are vague and uncertain. In this paper, we develop a method to
predict the cell load and to solve the RRM problem based on the
GF-RRM, and support the present facility has been built on the
application-level of the wireless networks. The GF-RRM exhibits the
better adaptability, fault-tolerant capability and performance than other
algorithms. Through simulations, we evaluate the blocking rate, update
overhead, and channel acquisition delay time of the proposed method.
The results demonstrate our algorithm has the lower blocking rate, less
updated overhead, and shorter channel acquisition delay.
Abstract: In this paper, an adaptive polarized Multiple-Input
Multiple-Output (MIMO) Multicarrier Spread Spectrum Code Division Multiple Access (MC-SS-CDMA) system is designed for downlink mobile communications. The proposed system will be
examined in Frequency Division Duplex (FDD) mode for both macro urban and suburban environments. For the same transmission
bandwidth, a performance comparison between both nonoverlapped and orthogonal Frequency Division Multiplexing (FDM) schemes will be presented. Also, the proposed system will be compared with
both the closed loop vertical MIMO MC-SS-CDMA system and the
synchronous vertical STBC-MIMO MC-SS-CDMA system. As will
be shown, the proposed system introduces a significant performance
gain as well as reducing the spatial dimensions of the MIMO system
and simplifying the receiver implementation. The effect of the
polarization diversity characteristics on the BER performance will be
discussed. Also, the impact of excluding the cross-polarization MCSS-
CDMA blocks in the base station will be investigated. In addition,
the system performance will be evaluated under different Feedback
Information (FBI) rates for slowly-varying channels. Finally, a
performance comparison for vehicular and pedestrian environments
will be presented
Abstract: IEEE 802.16 is a new wireless technology standard, it
has some advantages, including wider coverage, higher bandwidth,
and QoS support. As the new wireless technology for last mile
solution, there are designed two models in IEEE 802.16 standard. One
is PMP (point to multipoint) and the other is Mesh. In this paper we
only focus on IEEE 802.16 Mesh model. According to the IEEE
802.16 standard description, Mesh model has two scheduling modes,
centralized and distributed. Considering the pros and cons of the two
scheduling, we present the combined scheduling QoS framework that
the BS (Base Station) controls time frame scheduling and selects the
shortest path from source to destination directly. On the other hand, we
propose the Expedited Queue mechanism to cut down the transmission
time. The EQ mechanism can reduce a lot of end-to-end delay in our
QoS framework. Simulation study has shown that the average delay is
smaller than contrasts. Furthermore, our proposed scheme can also
achieve higher performance.
Abstract: Wireless Sensor Network (WSN) comprises of sensor
nodes which are designed to sense the environment, transmit sensed
data back to the base station via multi-hop routing to reconstruct
physical phenomena. Since physical phenomena exists significant
overlaps between temporal redundancy and spatial redundancy, it is
necessary to use Redundancy Suppression Algorithms (RSA) for sensor
node to lower energy consumption by reducing the transmission
of redundancy. A conventional algorithm of RSAs is threshold-based
RSA, which sets threshold to suppress redundant data. Although
many temporal and spatial RSAs are proposed, temporal-spatial RSA
are seldom to be proposed because it is difficult to determine when
to utilize temporal or spatial RSAs. In this paper, we proposed a
novel temporal-spatial redundancy suppression algorithm, Codebookbase
Redundancy Suppression Mechanism (CRSM). CRSM adopts
vector quantization to generate a codebook, which is easily used to
implement temporal-spatial RSA. CRSM not only achieves power
saving and reliability for WSN, but also provides the predictability
of network lifetime. Simulation result shows that the network lifetime
of CRSM outperforms at least 23% of that of other RSAs.
Abstract: Wireless sensor networks are consisted of hundreds or
thousands of small sensors that have limited resources.
Energy-efficient techniques are the main issue of wireless sensor
networks. This paper proposes an energy efficient agent-based
framework in wireless sensor networks. We adopt biologically
inspired approaches for wireless sensor networks. Agent operates
automatically with their behavior policies as a gene. Agent aggregates
other agents to reduce communication and gives high priority to nodes
that have enough energy to communicate. Agent behavior policies are
optimized by genetic operation at the base station. Simulation results
show that our proposed framework increases the lifetime of each node.
Each agent selects a next-hop node with neighbor information and
behavior policies. Our proposed framework provides self-healing,
self-configuration, self-optimization properties to sensor nodes.
Abstract: Mobile ad-hoc networks (MANETs) are a form of
wireless networks which do not require a base station for providing
network connectivity. Mobile ad-hoc networks have many
characteristics which distinguish them from other wireless networks
which make routing in such networks a challenging task. Cluster
based routing is one of the routing schemes for MANETs in which
various clusters of mobile nodes are formed with each cluster having
its own clusterhead which is responsible for routing among clusters.
In this paper we have proposed and implemented a distributed
weighted clustering algorithm for MANETs. This approach is based
on combined weight metric that takes into account several system
parameters like the node degree, transmission range, energy and
mobility of the nodes. We have evaluated the performance of
proposed scheme through simulation in various network situations.
Simulation results show that proposed scheme outperforms the
original distributed weighted clustering algorithm (DWCA).
Abstract: The cellular network is one of the emerging areas of
communication, in which the mobile nodes act as member for one
base station. The cluster based communication is now an emerging
area of wireless cellular multimedia networks. The cluster renders
fast communication and also a convenient way to work with
connectivity. In our scheme we have proposed an optimization
technique for the fuzzy cluster nodes, by categorizing the group
members into three categories like long refreshable member, medium
refreshable member and short refreshable member. By considering
long refreshable nodes as static nodes, we compute the new
membership values for the other nodes in the cluster. We compare
their previous and present membership value with the threshold value
to categorize them into three different members. By which, we
optimize the nodes in the fuzzy clusters. The simulation results show
that there is reduction in the cluster computational time and
iterational time after optimization.
Abstract: The issue of real-time and reliable report delivery is extremely important for taking effective decision in a real world mission critical Wireless Sensor Network (WSN) based application. The sensor data behaves differently in many ways from the data in traditional databases. WSNs need a mechanism to register, process queries, and disseminate data. In this paper we propose an architectural framework for data placement and management. We propose a reliable and real time approach for data placement and achieving data integrity using self organized sensor clusters. Instead of storing information in individual cluster heads as suggested in some protocols, in our architecture we suggest storing of information of all clusters within a cell in the corresponding base station. For data dissemination and action in the wireless sensor network we propose to use Action and Relay Stations (ARS). To reduce average energy dissipation of sensor nodes, the data is sent to the nearest ARS rather than base station. We have designed our architecture in such a way so as to achieve greater energy savings, enhanced availability and reliability.
Abstract: COSMED K4b2 is a portable electrical device designed to test pulmonary functions. It is ideal for many applications that need the measurement of the cardio-respiratory response either in the field or in the lab is capable with the capability to delivery real time data to a sink node or a PC base station with storing data in the memory at the same time. But the actual sensor outputs and data received may contain some errors, such as impulsive noise which can be related to sensors, low batteries, environment or disturbance in data acquisition process. These abnormal outputs might cause misinterpretations of exercise or living activities to persons being monitored. In our paper we propose an effective and feasible method to detect and identify errors in applications by principal component analysis (PCA) and a back propagation (BP) neural network.
Abstract: Wireless Sensor Networks consist of small battery
powered devices with limited energy resources. once deployed, the
small sensor nodes are usually inaccessible to the user, and thus
replacement of the energy source is not feasible. Hence, One of the
most important issues that needs to be enhanced in order to improve
the life span of the network is energy efficiency. to overcome this
demerit many research have been done. The clustering is the one of
the representative approaches. in the clustering, the cluster heads
gather data from nodes and sending them to the base station. In this
paper, we introduce a dynamic clustering algorithm using genetic
algorithm. This algorithm takes different parameters into
consideration to increase the network lifetime. To prove efficiency of
proposed algorithm, we simulated the proposed algorithm compared
with LEACH algorithm using the matlab
Abstract: We address the problem of joint beamforming and multipath channel parameters estimation in Wideband Code Division Multiple Access (WCDMA) communication systems that employ Multiple-Access Interference (MAI) suppression techniques in the uplink (from mobile to base station). Most of the existing schemes rely on time multiplex a training sequence with the user data. In WCDMA, the channel parameters can also be estimated from a code multiplexed common pilot channel (CPICH) that could be corrupted by strong interference resulting in a bad estimate. In this paper, we present new methods to combine interference suppression together with channel estimation when using multiple receiving antennas by using adaptive signal processing techniques. Computer simulation is used to compare between the proposed methods and the existing conventional estimation techniques.
Abstract: A new and cost effective robotic device was designed
for remote tele surgery using dual tone multi frequency technology
(DTMF). Tele system with Dual Tone Multiple Frequency has a large
capability in sending and receiving of data in hardware and software.
The robot consists of DC motors for arm movements and it is
controlled manually through a mobile phone through DTMF
Technology. The system enables the surgeon from base station to
send commands through mobile phone to the patient’s robotic system
which includes two robotic arms that translate the input into actual
instrument manipulation. A mobile phone attached to the
microcontroller 8051 which can activate robot through relays. The
Remote robot-assisted tele surgery eliminates geographic constraints
for getting surgical expertise where it is needed and allows an expert
surgeon to teach or proctor the performance of surgical technique by
real-time intervention.
Abstract: In practice, wireless networks has the property that
the signal strength attenuates with respect to the distance from the
base station, it could be better if the nodes at two hop away are
considered for better quality of service. In this paper, we propose a
procedure to identify delay preserving substructures for a given
wireless ad-hoc network using a new graph operation G 2 – E (G) =
G* (Edge difference of square graph of a given graph and the
original graph). This operation helps to analyze some induced
substructures, which preserve delay in communication among them.
This operation G* on a given graph will induce a graph, in which 1-
hop neighbors of any node are at 2-hop distance in the original
network. In this paper, we also identify some delay preserving
substructures in G*, which are (i) set of all nodes, which are mutually
at 2-hop distance in G that will form a clique in G*, (ii) set of nodes
which forms an odd cycle C2k+1 in G, will form an odd cycle in G*
and the set of nodes which form a even cycle C2k in G that will form
two disjoint companion cycles ( of same parity odd/even) of length k
in G*, (iii) every path of length 2k+1 or 2k in G will induce two
disjoint paths of length k in G*, and (iv) set of nodes in G*, which
induces a maximal connected sub graph with radius 1 (which
identifies a substructure with radius equal 2 and diameter at most 4 in
G). The above delay preserving sub structures will behave as good
clusters in the original network.
Abstract: To support user mobility for a wireless network new mechanisms are needed and are fundamental, such as paging, location updating, routing, and handover. Also an important key feature is mobile QoS offered by the WATM. Several ATM network protocols should be updated to implement mobility management and to maintain the already ATM QoS over wireless ATM networks. A survey of the various schemes and types of handover is provided. Handover procedure allows guarantee the terminal connection reestablishment when it moves between areas covered by different base stations. It is useful to satisfy user radio link transfer without interrupting a connection. However, failure to offer efficient solutions will result in handover important packet loss, severe delays and degradation of QoS offered to the applications. This paper reviews the requirements, characteristics and open issues of wireless ATM, particularly with regard to handover. It introduces key aspects of WATM and mobility extensions, which are added in the fixed ATM network. We propose a flexible approach for handover management that will minimize the QoS deterioration. Functional entities of this flexible approach are discussed in order to achieve minimum impact on the connection quality when a MT crosses the BS.
Abstract: It is important to provide possibility of so called
“handover" for the mobile subscriber from GSM network to Wi-Fi
network and back. To solve specified problem it is necessary to
estimate connection time between base station and wireless access
point. Difficulty to estimate this parameter is that it doesn-t described
in specifications of the standard and, hence, no recommended value
is given.
In this paper, the analytical model is presented that allows the
estimating connection time between base station and IEEE 802.11
access point.
Abstract: Sensor networks are often deployed in unattended
environments, thus leaving these networks vulnerable to false data
injection attacks in which an adversary injects forged reports into the
network through compromised nodes, with the goal of deceiving the
base station or depleting the resources of forwarding nodes. Several
research solutions have been recently proposed to detect and drop such
forged reports during the forwarding process. Each design can provide
the equivalent resilience in terms of node compromising. However,
their energy consumption characteristics differ from each other. Thus,
employing only a single filtering scheme for a network is not a
recommendable strategy in terms of energy saving. It's very important
the threshold determination for message authentication to identify. We
propose the recursive contract net protocols which less energy level of
terminal node in wireless sensor network.
Abstract: Wireless location is to determine the mobile station (MS) location in a wireless cellular communications system. When fewer base stations (BSs) may be available for location purposes or the measurements with large errors in non-line-of-sight (NLOS) environments, it is necessary to integrate all available heterogeneous measurements to achieve high location accuracy. This paper illustrates a hybrid proposed schemes that combine time of arrival (TOA) at three BSs and angle of arrival (AOA) information at the serving BS to give a location estimate of the MS. The proposed schemes mitigate the NLOS effect simply by the weighted sum of the intersections between three TOA circles and the AOA line without requiring a priori information about the NLOS error. Simulation results show that the proposed methods can achieve better accuracy when compare with Taylor series algorithm (TSA) and the hybrid lines of position algorithm (HLOP).
Abstract: In this paper, a reliable cooperative multipath routing
algorithm is proposed for data forwarding in wireless sensor networks
(WSNs). In this algorithm, data packets are forwarded towards the
base station (BS) through a number of paths, using a set of relay
nodes. In addition, the Rayleigh fading model is used to calculate
the evaluation metric of links. Here, the quality of reliability is
guaranteed by selecting optimal relay set with which the probability
of correct packet reception at the BS will exceed a predefined
threshold. Therefore, the proposed scheme ensures reliable packet
transmission to the BS. Furthermore, in the proposed algorithm,
energy efficiency is achieved by energy balancing (i.e. minimizing
the energy consumption of the bottleneck node of the routing path)
at the same time. This work also demonstrates that the proposed
algorithm outperforms existing algorithms in extending longevity of
the network, with respect to the quality of reliability. Given this, the
obtained results make possible reliable path selection with minimum
energy consumption in real time.
Abstract: Long Term Evolution (LTE) is a 4G wireless
broadband technology developed by the Third Generation
Partnership Project (3GPP) release 8, and it's represent the
competitiveness of Universal Mobile Telecommunications System
(UMTS) for the next 10 years and beyond. The concepts for LTE
systems have been introduced in 3GPP release 8, with objective of
high-data-rate, low-latency and packet-optimized radio access
technology. In this paper, performance of different TCP variants
during LTE network investigated. The performance of TCP over
LTE is affected mostly by the links of the wired network and total
bandwidth available at the serving base station. This paper describes
an NS-2 based simulation analysis of TCP-Vegas, TCP-Tahoe, TCPReno,
TCP-Newreno, TCP-SACK, and TCP-FACK, with full
modeling of all traffics of LTE system. The Evaluation of the
network performance with all TCP variants is mainly based on
throughput, average delay and lost packet. The analysis of TCP
performance over LTE ensures that all TCP's have a similar
throughput and the best performance return to TCP-Vegas than other
variants.