Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: Helical milling operations are used to generate or
enlarge boreholes by means of a milling tool. The bore diameter can be
adjusted through the diameter of the helical path. The kinematics of
helical milling on a three axis machine tool is analysed firstly. The
relationships between processing parameters, cutting tool geometry
characters with machined hole feature are formulated. The feed motion
of the cutting tool has been decomposed to plane circular feed and
axial linear motion. In this paper, the time varying cutting forces acted
on the side cutting edges and end cutting edges of the flat end cylinder
miller is analysed using a discrete method separately. These two
components then are combined to produce the cutting force model
considering the complicated interaction between the cutters and
workpiece. The time varying cutting force model describes the
instantaneous cutting force during processing. This model could be
used to predict cutting force, calculate statics deflection of cutter and
workpiece, and also could be the foundation of dynamics model and
predicting chatter limitation of the helical milling operations.
Abstract: Generation system reliability assessment is an
important task which can be performed using deterministic or
probabilistic techniques. The probabilistic approaches have
significant advantages over the deterministic methods. However,
more complicated modeling is required by the probabilistic
approaches. Power generation model is a basic requirement for this
assessment. One form of the generation models is the well known
capacity outage probability table (COPT). Different analytical
techniques have been used to construct the COPT. These approaches
require considerable mathematical modeling of the generating units.
The unit-s models are combined to build the COPT which will add
more burdens on the process of creating the COPT. Decimal to
Binary Conversion (DBC) technique is widely and commonly applied
in electronic systems and computing This paper proposes a novel
utilization of the DBC to create the COPT without engaging in
analytical modeling or time consuming simulations. The simple
binary representation , “0 " and “1 " is used to model the states o f
generating units. The proposed technique is proven to be an effective
approach to build the generation model.
Abstract: In this paper, an analytical modeling is presentated to
describe the channel noise in GME SGT/CGT MOSFET, based on
explicit functions of MOSFETs geometry and biasing conditions for
all channel length down to deep submicron and is verified with the
experimental data. Results shows the impact of various parameters
such as gate bias, drain bias, channel length ,device diameter and gate
material work function difference on drain current noise spectral
density of the device reflecting its applicability for circuit design
applications.
Abstract: Thermoelastic temperature, displacement, and
stress in heat transfer during laser surface hardening are solved
in Eulerian formulation. In Eulerian formulations the heat flux
is fixed in space and the workpiece is moved through a control
volume. In the case of uniform velocity and uniform heat flux
distribution, the Eulerian formulations leads to a steady-state
problem, while the Lagrangian formulations remains transient.
In Eulerian formulations the reduction to a steady-state
problem increases the computational efficiency. In this study
also an analytical solution is developed for an uncoupled
transient heat conduction equation in which a plane slab is
heated by a laser beam. The thermal result of the numerical
model is compared with the result of this analytical model.
Comparing the results shows numerical solution for uncoupled
equations are in good agreement with the analytical solution.
Abstract: Urban road network traffic has become one of the
most studied research topics in the last decades. This is mainly due to
the enlargement of the cities and the growing number of motor
vehicles traveling in this road network. One of the most sensitive
problems is to verify if the network is congestion-free. Another
related problem is the automatic reconfiguration of the network
without building new roads to alleviate congestions. These problems
require an accurate model of the traffic to determine the steady state
of the system. An alternative is to simulate the traffic to see if there
are congestions and when and where they occur. One key issue is to
find an adequate model for road intersections. Once the model
established, either a large scale model is built or the intersection is
represented by its performance measures and simulation for analysis.
In both cases, it is important to seek the queueing model to represent
the road intersection. In this paper, we propose to model the road
intersection as a BCMP queueing network and we compare this
analytical model against a simulation model for validation.