Abstract: Today, the central role of industrial robots in automation in general and in material handling in particular is crystal clear. Based on the current status of Photovoltaics and by focusing on lightweight material handling, PV industry has turned into a potential candidate for introducing a fresh “pick and place" robot technology. Thus, to examine the industry needs in this regard, firstly the best suited applications for such robotic automation,and then the essential prerequisites in PV industry should be identified. The objective of this paper is to present holistic views on the industry trends, general automation status and existing challenges facing lightweight robotic material handling in PV Silicon Wafer and Thin Film technologies. The results of this study show that currently no uniform pick and place solution prevails among PV Silicon Wafer manufacturers and the industry calls for a new robot solution to satisfy its needs in new directions.
Abstract: The electrokinetic flow resistance (electroviscous
effect) is predicted for steady state, pressure-driven liquid flow at
low Reynolds number in a microfluidic contraction of rectangular
cross-section. Calculations of the three dimensional flow are
performed in parallel using a finite volume numerical method. The
channel walls are assumed to carry a uniform charge density and the
liquid is taken to be a symmetric 1:1 electrolyte. Predictions are
presented for a single set of flow and electrokinetic parameters. It is
shown that the magnitude of the streaming potential gradient and the
charge density of counter-ions in the liquid is greater than that in
corresponding two-dimensional slit-like contraction geometry. The
apparent viscosity is found to be very close to the value for a
rectangular channel of uniform cross-section at the chosen Reynolds
number (Re = 0.1). It is speculated that the apparent viscosity for the
contraction geometry will increase as the Reynolds number is
reduced.
Abstract: A game animals – elk (Alces alces), deer (Cervus
elaphus), roe deer (Capreolus capreolus) or wild boar (Sus scrofa
scrofa) - every autumn and winter period provide an excellent
investment, diversification of many consumer meals. In last years
consumption and assortiment of game meat products significantly
increase. Investigations about biochemical composition of game meat
are not very much. The meat of wild animals is more favourable for
human health because it has lower saturated fatty acids content, but
higher content of protein. Therefore the aim of investigations was to
compare biochemical composition of ungulates obtained in
Latvia.Investigations were carried out in wild animals different
regions of Latvia. In the studied samples protein, intramuscular fat,
fatty acids and cholesterol were determined. The biochemical
analysis of 54 samples were done. Results of analysis showed that
protein content 22.36 – 22.92% of all types of meat samples is not
different statistically, significantly lower fat content 1.33 ± 0.88%
had elk meat samples and 1.59 ± 0.59% roe deer samples. Content of
cholesterol was various 64.41 – 95.07% in the ruminant meat
samples of different species. From the dietetic point of view the best
composition of fatty acids has meat samples of roe deer.
Abstract: The present study aims to evaluating the effect of
rotor solidity - in terms of chord length for a given rotor diameter - on
the performances of a small vertical axis Darrieus wind turbine. The
proposed work focuses on both power production and rotor power
coefficient, considering also the structural constraints deriving from
the centrifugal forces due to rotor angular velocity. Also the
smoothness of the resulting power curves have been investigated, in
order to evaluate the controllability of the corresponding rotor
architectures.
Abstract: Microbial oil was produced by soil isolated
oleaginous yeast YU5/2 in flask-batch fermentation. The yeast was
identified by molecular genetics technique based on sequence
analysis of the variable D1/D2 domain of the large subunit (26S)
ribosomal DNA and it was identified as Torulaspora globosa. T.
globosa YU5/2 supported maximum values of 0.520 g/L/d, 0.472 g
lipid/g cells, 4.16 g/L, and 0.156 g/L/d for volumetric lipid
production rate, and specific yield of lipid, lipid concentration, and
specific rate of lipid production respectively, when culture was
performed in nitrogen-limiting medium supplemented with 80g/L
glucose. Among the carbon sources tested, maximum cell yield
coefficient (YX/S, g/L), maximum specific yield of lipid (YP/X, g
lipid/g cells) and volumetric lipid production rate (QP, g/L/d) were
found of 0.728, 0.237, and 0.619, respectively, using sweet potato
tubers hydrolysates as carbon source.
Abstract: A new hybrid coding method for compressing
animated polygonal meshes is presented. This paper assumes
the simplistic representation of the geometric data: a temporal
sequence of polygonal meshes for each discrete frame of the
animated sequence. The method utilizes a delta coding and an
octree-based method. In this hybrid method, both the octree
approach and the delta coding approach are applied to each
single frame in the animation sequence in parallel. The
approach that generates the smaller encoded file size is chosen
to encode the current frame. Given the same quality
requirement, the hybrid coding method can achieve much
higher compression ratio than the octree-only method or the
delta-only method. The hybrid approach can represent 3D
animated sequences with higher compression factors while
maintaining reasonable quality. It is easy to implement and have
a low cost encoding process and a fast decoding process, which
make it a better choice for real time application.
Abstract: Power system stabilizers (PSS) are now routinely used in the industry to damp out power system oscillations. In this paper, particle swarm optimization (PSO) technique is applied to design a robust power system stabilizer (PSS). The design problem of the proposed controller is formulated as an optimization problem and PSO is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The non-linear simulation results are presented under wide range of operating conditions; disturbances at different locations as well as for various fault clearing sequences to show the effectiveness and robustness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. Further, all the simulations results are compared with a conventionally designed power system stabilizer to show the superiority of the proposed design approach.
Abstract: Aim of this work was to compare the efficacy of two
loading methods of proteins onto polymeric nanocarriers: adsorption
and encapsulation methods. Preliminary studies of protein loading
were done using Bovine Serum Albumin (BSA) as model protein.
Nanocarriers were prepared starting from polylactic co-glycolic acid
(PLGA) polymer; production methods used are two different variants
of emulsion evaporation method. Nanoparticles obtained were
analyzed in terms of dimensions by Dynamic Light Scattering and
Loading Efficiency of BSA by Bradford Assay. Loaded
nanoparticles were then submitted to in-vitro protein dissolution test
in order to study the effect of the delivery system on the release rate
of the protein.
Abstract: Asthma is a condition that causing chronic health problems in children. In addition to basic therapy against disease, we must try to reduce the impact of chronic health problems and also optimize their medical aspect of growth and development. A boy with mild asthma attack frequent episode did not showed any improvement with medical treatment and his asthma control test was 11. From radiologic examination he got hyperaerated lung and billateral sinusitis maxillaris; skin test results were house dust, food and pet allergy; an overweight body; bad school grades; psychological and environmental problem. We followed and evaluated this boy in 6 months, treated holistically. Even we could not do much on environmental but no more psychological and school problems, his on a good bodyweight and his asthma control test was 22. A case of a child with mild asthma attack frequent episode was reported. Asthma clinical course show no significant improvement when other predisposing factor is not well-controlled and a child’s growth and development may be affected. Improving condition of the patient can be created with the help of loving and caring way of nurturing from the parents and supportive peer group. Therefore, continuous and consistent monitoring is required because prognosis of asthma is generally good when regularly and properly controlled.
Abstract: Twenty four New Zealand white rabbits (12 does and
12 bucks) and twenty four Flanders (12 does and 12 bucks) rabbits,
allotted into two feeding regime (6 for each breed, 3 males and 3
females) first one fed commercial ration and second one fed
commercial diet plus sodium butyrate (300 g/ton). The obtained
results showed that at end of 8th week experimental period New
Zealand white rabbits were heavier body weight than Flanders rabbits
(1934.55+39.05 vs. 1802.5+30.99 g); significantly high body weight
gain during experimental period especially during 8th week
(136.1+3.5 vs. 126.8+1.8 g/week); better feed conversion ratio during
all weeks of experiment from first week (3.07+0.16 vs. 3.12+0.10)
till the 8th week of experiment (5.54+0.16 vs. 5.76+0.07) with
significantly high dressing percentages (0.54+0.01 vs. 0.52+0.01).
Also all carcass cuts were significantly high in New Zealand white
rabbits than Flanders. Females rabbits (at the same age) were lower
body weight than males from start of experiment (941.1+39.8
vs.972.1+33.5 g) till the end of experiment (1833.64+37.69 vs.
1903.41+36.93 g); gained less during all weeks of experiment except
during 8th week (132.1+2.3 vs. 130.9+3.4 g/week), with lower
dressing percentage (0.52+0.01 vs. 0.53+0.01) and lighter carcass
cuts than males, however, they had better feed conversion ratio
during 1st week, 7th week and 8th week of experiment. Addition of
300g sodium butyrate/ton of rabbit increased the body weight of
rabbits at the end of experimental period (1882.71+26.45 vs.
1851.5+49.82 g); improve body weight gain at 3rd, 4th, 5th, 6th and
7th week of experiment and significantly improve feed conversion
ratio during all weeks of the experiment from 1st week (2.85+0.07
vs. 3.30+0.15) till the 8th week of the experiment (5.51+0.12 vs.
5.77+0.12). Also the dressing percentage was higher in Sodium
butyrate fed groups than control one (0.53+0.01 vs. 0.52+0.01) and
the most important results of feeding sodium butyrate is the reducing
of the mortality percentage in rabbits during 8 week experiment to
zero percentage as compared with 16% in control group.
Abstract: The scattering effect of light in fog improves the
difficulty in visibility thus introducing disturbances in transport
facilities in urban or industrial areas causing fatal accidents or public
harassments, therefore, developing an enhanced fog vision system
with radio wave to improvise the way outs of these severe problems
is really a big challenge for researchers. Series of experimental
studies already been done and more are in progress to know the
weather effect on radio frequencies for different ranges. According to
Rayleigh scattering Law, the propagating wavelength should be
greater than the diameter of the particle present in the penetrating
medium. Direct wave RF signal thus have high chance of failure to
work in such weather for detection of any object. Therefore an
extensive study was required to find suitable region in the RF band
that can help us in detecting objects with proper shape. This paper
produces some results on object detection using 912 MHz band with
successful detection of the persistence of any object coming under the
trajectory of a vehicle navigating in indoor and outdoor environment.
The developed images are finally transformed to video signal to
enable continuous monitoring.
Abstract: The main purpose of this paper is to investigate thelong-run equilibrium and short-run dynamics of international housing prices when macroeconomic variables change. We apply the Pedroni’s, panel cointegration, using the unbalanced panel data analysis of 33 countries over the period from 1980Q1 to 2013Q1, to examine the relationships among house prices and macroeconomic variables. Our empirical results of panel data cointegration tests support the existence of a cointegration among these macroeconomic variables and house prices. Besides, the empirical results of panel DOLS further present that a 1% increase in economic activity, long-term interest rates, and construction costs cause house prices to respectively change 2.16%, -0.04%, and 0.22% in the long run.Furthermore, the increasing economic activity and the construction cost would cause strongerimpacts on the house prices for lower income countries than higher income countries.The results lead to the conclusion that policy of house prices growth can be regarded as economic growth for lower income countries. Finally, in America region, the coefficient of economic activity is the highest, which displays that increasing economic activity causes a faster rise in house prices there than in other regions. There are some special cases whereby the coefficients of interest rates are significantly positive in America and Asia regions.
Abstract: The purpose of this study was to examine to what
extend classroom management efficacy, marital status, gender, and
teaching experience predict burnout among primary school teachers.
Participants of this study were 523 (345 female, 178 male) teachers
who completed inventories. The results of multiple regression
analysis indicated that three dimensions of teacher burnout
(Emotional Exhaustion, Depersonalization, Personal
Accomplishment) were affected differently from four predictor
variables. Findings indicated that for the emotional exhaustion,
classroom management efficacy, marital status and teaching
experience; for depersonalization dimension, classroom management
efficacy and marital status and finally for the personal
accomplishment dimension, classroom management efficacy, gender,
and teaching experience were significant predictors.
Abstract: Response surface methodology with Box–Benhken (BB) design of experiment approach has been utilized to study the mechanism of interface slip damping in layered and jointed tack welded beams with varying surface roughness. The design utilizes the initial amplitude of excitation, tack length and surface roughness at the interfaces to develop the model for the logarithmic damping decrement of the layered and jointed welded structures. Statistically designed experiments have been performed to estimate the coefficients in the mathematical model, predict the response, and check the adequacy of the model. Comparison of predicted and experimental response values outside the design conditions have shown good correspondence, implying that empirical model derived from response surface approach can be effectively used to describe the mechanism of interface slip damping in layered and jointed tack welded structures.
Abstract: The purpose of my research proposal is to
demonstrate that there is a relationship between EEG and
endometrial cancer.
The above relationship is based on an Aristotelian Syllogism;
since it is known that the 14-3-3 protein is related to the electrical
activity of the brain via control of the flow of Na+ and K+ ions and
since it is also known that many types of cancer are associated with
14-3-3 protein, it is possible that there is a relationship between EEG
and cancer. This research will be carried out by well-defined
diagnostic indicators, obtained via the EEG, using signal processing
procedures and pattern recognition tools such as neural networks in
order to recognize the endometrial cancer type. The current research
shall compare the findings from EEG and hysteroscopy performed on
women of a wide age range. Moreover, this practice could be
expanded to other types of cancer. The implementation of this
methodology will be completed with the creation of an ontology.
This ontology shall define the concepts existing in this research-s
domain and the relationships between them. It will represent the
types of relationships between hysteroscopy and EEG findings.
Abstract: The aim of this study was to evaluate the sensitivity
of a range of EEG indices to time-on-task effects and to a workload
manipulation (cueing), during performance of a resource-limited
vigilance task. Effects of task period and cueing on performance and
subjective state response were consistent with previous vigilance
studies and with resource theory. Two EEG indices – the Task Load
Index (TLI) and global lower frequency (LF) alpha power – showed
effects of task period and cueing similar to those seen with correct
detections. Across four successive task periods, the TLI declined and
LF alpha power increased. Cueing increased TLI and decreased LF
alpha. Other indices – the Engagement Index (EI), frontal theta and
upper frequency (UF) alpha failed to show these effects. However, EI
and frontal theta were sensitive to interactive effects of task period
and cueing, which may correspond to a stronger anxiety response to
the uncued task.
Abstract: In recent years Operational Transconductance Amplifier based high frequency integrated circuits, filters and systems have been widely investigated. The usefulness of OTAs over conventional OP-Amps in the design of both first order and second order active filters are well documented. This paper discusses some of the tunability issues using the Matlab/Simulink® software which are previously unreported for any commercial OTA. Using the simulation results two first order voltage controlled all pass filters with phase tuning capability are proposed.
Abstract: Predictions of flow and heat transfer characteristics and shape optimization in internally finned circular tubes have been performed on three-dimensional periodically fully developed turbulent flow and thermal fields. For a trapezoidal fin profile, the effects of fin height h, upper fin widths d1, lower fin widths d2, and helix angle of fin ? on transport phenomena are investigated for the condition of fin number of N = 30. The CFD and mathematical optimization technique are coupled in order to optimize the shape of internally finned tube. The optimal solutions of the design variables (i.e., upper and lower fin widths, fin height and helix angle) are numerically obtained by minimizing the pressure loss and maximizing the heat transfer rate, simultaneously, for the limiting conditions of d1 = 0.5~1.5 mm, d2 = 0.5~1.5 mm, h= 0.5~1.5mm, ? = 10~30 degrees. The fully developed flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the multi-objective genetic algorithm that is widely used in the constrained nonlinear optimization problem.
Abstract: In conventional seedling production, the seedlings are
being grown in the open field under natural conditions. Here they are
susceptible to sudden changes in climate were their quality and yield
is affected. Quality seedlings are essential for good growth and
performance of crops in main field; they serve as a foundation for the
economic returns to the farmer. Producing quality seedling demands
usage of hybrid seeds as they have the ability to result in better yield,
greater uniformity, improved color, disease resistance, and so forth.
Hybrid seed production poses major operational challenge and its
seed use efficiency plays an important role. Thus in order to
overcome the difficulties currently present in conventional seedling
production and to efficiently use hybrid seeds, ITC Limited Agri
Business Divisions - Sustainability Cell as conceptualized a novel
method of seedling production unit for farmers in West Godavari
District of Andhra Pradesh. The “Green House based Float Seedling"
methodology aims at a protected cultivation technique wherein the
micro climate surrounding the plant/seedling body is controlled
partially or fully as per the requirement of the species. This paper
reports on the techno economic evaluation of green house for
cultivation of float based seedling production with experimental
results that was attained from the pilot implementation in West
Godavari District, Rajahmundry region of India.
Abstract: FW4 is a newly developed hot die material widely
used in Forging Dies manufacturing. The right selection of the
machining conditions is one of the most important aspects to take
into consideration in the Electrical Discharge Machining (EDM) of
FW4. In this paper an attempt has been made to develop
mathematical models for relating the Material Removal Rate (MRR),
Tool Wear Ratio (TWR) and surface roughness (Ra) to machining
parameters (current, pulse-on time and voltage). Furthermore, a study
was carried out to analyze the effects of machining parameters in
respect of listed technological characteristics. The results of analysis
of variance (ANOVA) indicate that the proposed mathematical
models, can adequately describe the performance within the limits of
the factors being studied.