Abstract: Recently, universities are increasingly consuming
energy to support various activities. A large population of staff and
students in Malaysian universities has led to excessive energy
consumption which directly gives an impact to the environment. The
key question then ascended “How well is an energy management
(EM) been practiced in universities without taking the Critical
Success Factors (CSFs) into consideration to ensure the management
of university achieves the goals in reducing energy consumption.
Review on past literature is carried out to establish CSFs for EM best
practices. Thus, this paper highlighted the CSFs which have to be
focused on by management of university to successfully measure the
EM implementation and its performance. At the end of this paper, a
theoretical framework is developed for EM success factors towards
sustainable university.
Abstract: An experiment was conducted to determine the effect
of pollination on seed quality of rapeseed in Chitwan, Nepal during
2012-2013. The experiment was designed in Randomized Complete
Block with four replications and five treatments. The rapeseed plots
were caged with mosquito nets at 10% flowering except natural
pollination. Two-framed colonies of Apis mellifera L. and Apis
cerana F. were introduced separately for pollination, and control plot
caged without pollinators. The highest germination percent was
observed on Apis cerana F. pollinated plot seeds (90.50%
germination) followed by Apis mellifera L. pollinated plots (87.25 %)
and lowest on control plots (42.00% germination) seeds. Similarly,
seed test weight of Apis cerana F. pollinated plots (3.22 gm/ 1000
seed) and Apis mellifera L. pollinated plots (2.93 gm/1000 seed) were
and lowest on control plots (2.26 gm/ 1000 seed) recorded. Likewise,
oil content was recorded highest on pollinated by Apis cerana F.
(36.1%) followed by pollinated by Apis mellifera L. (35.4%) and
lowest on control plots (32.8%). This study clearly indicated
pollination increases the seed quality of rapeseed and therefore,
management of honeybee is necessary for producing higher quality of
rapeseed under Chitwan condition.
Abstract: The study examined the effect of Bonny Light whole
crude oil (WC) and its water soluble fraction (WSF) on the activities
of antioxidant enzymes (catalase (CAT) and superoxide dismutase
(SOD)) and crude mitochondria ATPases in the radicle of
germinating bean (Vigna unguiculata). The percentage germination,
level of lipid peroxidation, antioxidant enzyme and mitochondria
Ca2+ and Mg2+ ATPase activities were measured in the radicle of
bean after 7, 14 and 21 days post germination. Viable bean seeds
were planted in soils contaminated with 10ml, 25ml and 50ml of
whole crude oil (WC) and its water soluble fraction (WSF) to obtain
2, 5 and 10% v/w crude oil contamination. There was dose dependent
reduction of the number of bean seeds that germinated in the
contaminated soils compared with control (p
Abstract: This study carried out comparative seismic
performance of reinforced concrete frames infilled by masonry walls
with different heights. Partial and fully infilled reinforced concrete
frames were modeled for the research objectives and the analysis
model for a bare reinforced concrete frame was also established for
comparison. Non–linear static analyses for the studied frames were
performed to investigate their structural behavior under extreme
seismic loads and to find out their collapse mechanism. It was
observed from analysis results that the strengths of the partial infilled
reinforced concrete frames are increased and their ductilities are
reduced, as infilled masonry walls are higher. Especially, reinforced
concrete frames with higher partial infilled masonry walls would
experience shear failures. Non–linear dynamic analyses using 10
earthquake records show that the bare and fully infilled reinforced
concrete frame present stable collapse mechanism while the reinforced
concrete frames with partially infilled masonry walls collapse in more
brittle manner due to short-column effects.
Abstract: Interaction between human, location and activity
defines space. In the framework of these relations, space is a
container for current specifications in relations of the 3 mentioned
elements. The change of land utility considered with average
performance range, urban regulations, society requirements etc. will
provide welfare and comfort for citizens. From an engineering view it
is fundamental that choosing a proper location for a specific civil
activity requires evaluation of locations from different perspectives.
The debate of desirable establishment of municipal service elements
in urban regions is one of the most important issues related to urban
planning. In this paper, the research type is applicable based on goal,
and is descriptive and analytical based on nature. Initially existing
terminals in Esfahan are surveyed and then new locations are
presented based on evaluated criteria. In order to evaluate terminals
based on the considered factors, an AHP model is used at first to
estimate weight of different factors and then existing and suggested
locations are evaluated using Arc GIS software and AHP model
results. The results show that existing bus terminals are located in
fairly proper locations. Further results of this study suggest new
locations to establish terminals based on urban criteria.
Abstract: The present study was undertaken to investigate the
effect of aging parameters (time and temperature) on the mechanical
properties of Be-and/or Zr- treated Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys containing Be and/or Zr. Different aging
treatment were carried out for the as solution treated (SHT)
specimens (after quenching in warm water). The specimens were
aged at different conditions; Natural and artificial aging was carried
out at room temperature, 120C, 150C, 180C and 220C for different
periods of time. Duplex aging was performed for SHT conditions
(pre-aged at different time and temperature followed by high
temperature aging). Ultimate tensile strength, yield strength and %
elongation data results as a function of different aging parameters are
analysed. A statistical design of experiments (DOE) approach using
fractional factorial design is applied to acquire an understanding of
the effects of these variables and their interactions on the mechanical
properties of Be- and/or Zr- treated 7075 alloys. Mathematical
models are developed to relate the alloy mechanical properties with
the different aging parameters.
Abstract: The investigation in the present paper is to obtain
certain types of relations for the well known hypergeometric functions
by employing the technique of fractional derivative and integral.
Abstract: The western Tombolo of the Giens peninsula in
southern France, known as Almanarre beach, is subject to coastal
erosion. We are trying to use computer simulation in order to propose
solutions to stop this erosion. Our aim was first to determine the main
factors for this erosion and successfully apply a coupled hydrosedimentological
numerical model based on observations and
measurements that have been performed on the site for decades.
We have gathered all available information and data about waves,
winds, currents, tides, bathymetry, coastal line, and sediments
concerning the site. These have been divided into two sets: one
devoted to calibrating a numerical model using Mike 21 software, the
other to serve as a reference in order to numerically compare the
present situation to what it could be if we implemented different
types of underwater constructions.
This paper presents the first part of the study: selecting and
melting different sources into a coherent data basis, identifying the
main erosion factors, and calibrating the coupled software model
against the selected reference period.
Our results bring calibration of the numerical model with good
fitting coefficients. They also show that the winter South-Western
storm events conjugated to depressive weather conditions constitute a
major factor of erosion, mainly due to wave impact in the northern
part of the Almanarre beach. Together, current and wind impact is
shown negligible.
Abstract: The tombolo of Giens is located in the town of Hyères
(France). We recall the history of coastal erosion, and prominent
factors affecting the evolution of the western tombolo. We then
discuss the possibility of stabilizing the western tombolo. Our
argumentation relies on a coupled model integrating swells, currents,
water levels and sediment transport. We present the conclusions of
the simulations of various scenarios, including pre-existing
propositions from coastal engineering offices. We conclude that
beach replenishment seems to be necessary but not sufficient for the
stabilization of the beach. Breakwaters reveal effective particularly in
the most exposed northern area. Some solutions fulfill conditions so
as to be elected as satisfactory. We give a comparative analysis of the
efficiency of 14 alternatives for the protection of the tombolo.
Abstract: A novel hybrid model of the lumbar spine, allowing
fast static and dynamic simulations of the disc pressure
and the spine mobility, is introduced in this work. Our
contribution is to combine rigid bodies, deformable finite
elements, articular constraints, and springs into a unique model
of the spine. Each vertebra is represented by a rigid body
controlling a surface mesh to model contacts on the facet
joints and the spinous process. The discs are modeled using
a heterogeneous tetrahedral finite element model. The facet
joints are represented as elastic joints with six degrees of
freedom, while the ligaments are modeled using non-linear
one-dimensional elastic elements. The challenge we tackle
is to make these different models efficiently interact while
respecting the principles of Anatomy and Mechanics.
The mobility, the intradiscal pressure, the facet joint force and
the instantaneous center of rotation of the lumbar spine are
validated against the experimental and theoretical results of
the literature on flexion, extension, lateral bending as well as
axial rotation.
Our hybrid model greatly simplifies the modeling task and
dramatically accelerates the simulation of pressure within the
discs, as well as the evaluation of the range of motion and the
instantaneous centers of rotation, without penalizing precision.
These results suggest that for some types of biomechanical
simulations, simplified models allow far easier modeling and
faster simulations compared to usual full-FEM approaches
without any loss of accuracy.
Abstract: The aim of this paper is to give an assessment of
environmental effects of IPPC permit conditions of installations that
are in specific territory with high concentration of industrial
activities.
The IPPC permit is the permit that each operator should hold to
operate the installation as stated by the directive 2010/75/UE on
industrial emissions (integrated pollution prevention and control),
known as IED (Industrial Emissions Directive).
The IPPC permit includes all the measures necessary to achieve a
high level of protection of the environment as a whole, also defining
the monitoring requirements as measurement methodology,
frequency and evaluation procedure. The emissions monitoring of a
specific plant may also give indications of the contribution of these
emissions on the air quality of a definite area.
So, it is clear that the IPPC permits are important tools both to
improve the environmental framework and to achieve the air quality
standards, assisting to assess the possible industrial sources
contributions to air pollution.
Abstract: An analysis is carried out to investigate the effect of
magnetic field and heat source on the steady boundary layer flow and
heat transfer of a Casson nanofluid over a vertical cylinder stretching
exponentially along its radial direction. Using a similarity
transformation, the governing mathematical equations, with the
boundary conditions are reduced to a system of coupled, non –linear
ordinary differential equations. The resulting system is solved
numerically by the fourth order Runge – Kutta scheme with shooting
technique. The influence of various physical parameters such as
Reynolds number, Prandtl number, magnetic field, Brownian motion
parameter, thermophoresis parameter, Lewis number and the natural
convection parameter are presented graphically and discussed for non
– dimensional velocity, temperature and nanoparticle volume
fraction. Numerical data for the skin – friction coefficient, local
Nusselt number and the local Sherwood number have been tabulated
for various parametric conditions. It is found that the local Nusselt
number is a decreasing function of Brownian motion parameter Nb
and the thermophoresis parameter Nt.
Abstract: Advanced head and neck cancers are aggressive
tumours, which require aggressive treatment. Treatment efficiency is
often hindered by cancer cell repopulation during radiotherapy,
which is due to various mechanisms triggered by the loss of tumour
cells and involves both stem and differentiated cells. The aim of the
current paper is to present in silico simulations of radiotherapy
schedules on a virtual head and neck tumour grown with biologically
realistic kinetic parameters. Using the linear quadratic formalism of
cell survival after radiotherapy, altered fractionation schedules
employing various treatment breaks for normal tissue recovery are
simulated and repopulation mechanism implemented in order to
evaluate the impact of various cancer cell contribution on tumour
behaviour during irradiation. The model has shown that the timing of
treatment breaks is an important factor influencing tumour control in
rapidly proliferating tissues such as squamous cell carcinomas of the
head and neck. Furthermore, not only stem cells but also
differentiated cells, via the mechanism of abortive division, can
contribute to malignant cell repopulation during treatment.
Abstract: Different tools and technologies were implemented
for Crisis Response and Management (CRM) which is generally
using available network infrastructure for information exchange.
Depending on type of disaster or crisis, network infrastructure could
be affected and it could not be able to provide reliable connectivity.
Thus any tool or technology that depends on the connectivity could
not be able to fulfill its functionalities. As a solution, a new message
exchange framework has been developed. Framework provides
offline/online information exchange platform for CRM Information
Systems (CRMIS) and it uses XML compression and packet
prioritization algorithms and is based on open source web
technologies. By introducing offline capabilities to the web
technologies, framework will be able to perform message exchange
on unreliable networks. The experiments done on the simulation
environment provide promising results on low bandwidth networks
(56kbps and 28.8 kbps) with up to 50% packet loss and the solution is
to successfully transfer all the information on these low quality
networks where the traditional 2 and 3 tier applications failed.
Abstract: The increasing demand of gallium, indium and
rare-earth elements for the production of electronics, e.g. solid
state-lighting, photovoltaics, integrated circuits, and liquid crystal
displays, will exceed the world-wide supply according to current
forecasts. Recycling systems to reclaim these materials are not yet in
place, which challenges the sustainability of these technologies. This
paper proposes a multispectral imaging system as a basis for a vision
based recognition system for valuable components of electronics
waste. Multispectral images intend to enhance the contrast of images
of printed circuit boards (single components, as well as labels) for
further analysis, such as optical character recognition and entire
printed circuit board recognition. The results show, that a higher
contrast is achieved in the near infrared compared to ultraviolett and
visible light.
Abstract: Water contamination by toxic compound is one of the serious environmental problems today. These toxic compounds mostly originated from industrial effluents, agriculture, natural sources and human waste. These studies focus on modification of multiwalled carbon nanotube (MWCNTs) with nanoparticle of calixarene and explore the possibility of using this modification for the remediation of cadmium in water. The nanocomposites were prepared by dissolving calixarene in chloroform solution as solvent, followed by additional multiwalled carbon nanotube (MWCNTs) then sonication process for 3 hour and fabricated the nanocomposites on substrate by spin coating method. Finally, the nanocomposites were tested on cadmium ion (10 mg/ml). The morphology of nanocomposites was investigated by FESEM showing the formation of calixarene on the outer walls of carbon nanotube and cadmium ion also clearly seen from the micrograph. This formation was supported by using energy dispersive x-ray (EDX). The presence of cadmium ions in the films, leads to some changes in the surface potential and Fourier Transform Infrared spectroscopy (FTIR).The nanocomposites MWCNTs-calixarene have potential for development of sensor for pollutant monitoring and nanoelectronics devices applications.
Abstract: Image search engines rely on the surrounding textual
keywords for the retrieval of images. It is a tedious work for the
search engines like Google and Bing to interpret the user’s search
intention and to provide the desired results. The recent researches
also state that the Google image search engines do not work well on
all the images. Consequently, this leads to the emergence of efficient
image retrieval technique, which interprets the user’s search intention
and shows the desired results. In order to accomplish this task, an
efficient image re-ranking framework is required. Sequentially, to
provide best image retrieval, the new image re-ranking framework is
experimented in this paper. The implemented new image re-ranking
framework provides best image retrieval from the image dataset by
making use of re-ranking of retrieved images that is based on the
user’s desired images. This is experimented in two sections. One is
offline section and other is online section. In offline section, the reranking
framework studies differently (reference classes or Semantic
Spaces) for diverse user query keywords. The semantic signatures get
generated by combining the textual and visual features of the images.
In the online section, images are re-ranked by comparing the
semantic signatures that are obtained from the reference classes with
the user specified image query keywords. This re-ranking
methodology will increases the retrieval image efficiency and the
result will be effective to the user.
Abstract: The study of organisations’ information security
cultures has attracted scholars as well as healthcare services industry
to research the topic and find appropriate tools and approaches to
develop a positive culture. The vast majority of studies in Saudi
national health services are on the use of technology to protect and
secure health services information. On the other hand, there is a lack
of research on the role and impact of an organisation’s cultural
dimensions on information security. This research investigated and
analysed the role and impact of cultural dimensions on information
security in Saudi Arabia health service. Hypotheses were tested and
two surveys were carried out in order to collect data and information
from three major hospitals in Saudi Arabia (SA). The first survey
identified the main cultural-dimension problems in SA health
services and developed an initial information security culture
framework model. The second survey evaluated and tested the
developed framework model to test its usefulness, reliability and
applicability. The model is based on human behaviour theory, where
the individual’s attitude is the key element of the individual’s
intention to behave as well as of his or her actual behaviour. The
research identified a set of cultural and sub-cultural dimensions in SA
health information security and services.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: This paper presents a novel fractal antenna structure
proposed for UWB (Ultra – Wideband) applications. The frequency
band 3.1-10.6GHz released by FCC (Federal Communication
Commission) as the commercial operation of UWB has been chosen
as frequency range for this antenna based on coplanar waveguide
(CPW) feed and circular shapes fulfilled according to fractal
geometry. The proposed antenna is validated and designed by using
an FR4 substrate with overall area of 34x43 mm2. The simulated
results performed by CST-Microwave Studio and compared by ADS
(Advanced Design System) show good matching input impedance
with return loss less than -10dB between 2.9 GHz and 11 GHz.