Abstract: The analysis of Acoustic Emission (AE) signal
generated from metal cutting processes has often approached
statistically. This is due to the stochastic nature of the emission
signal as a result of factors effecting the signal from its generation
through transmission and sensing. Different techniques are applied in
this manner, each of which is suitable for certain processes. In metal
cutting where the emission generated by the deformation process is
rather continuous, an appropriate method for analysing the AE signal
based on the root mean square (RMS) of the signal is often used and
is suitable for use with the conventional signal processing systems.
The aim of this paper is to set a strategy in tool failure detection in
turning processes via the statistic analysis of the AE generated from
the cutting zone. The strategy is based on the investigation of the
distribution moments of the AE signal at predetermined sampling.
The skews and kurtosis of these distributions are the key elements in
the detection. A normal (Gaussian) distribution has first been
suggested then this was eliminated due to insufficiency. The so
called Beta distribution was then considered, this has been used with
an assumed β density function and has given promising results with
regard to chipping and tool breakage detection.
Abstract: If a possibility distribution and a probability distribution
are describing values x of one and the same system or process
x(t), can they relate to each other? Though in general the possibility
and probability distributions might be not connected at all, we
can assume that in some particular cases there is an association linked
them.
In the presented paper, we consider distributions of bloodstream
concentrations of physiologically active substances and propose that
the probability to observe a concentration x of a substance X can be
produced from the possibility of the event X = x .
The proposed assumptions and resulted theoretical distributions
are tested against the data obtained from various panel studies of the
bloodstream concentrations of the different physiologically active
substances in patients and healthy adults as well.
Abstract: An analysis is made of the flow of an incompressible viscoelastic fluid (of small memory) over a porous plate subject to suction or blowing. It is found that velocity at a point increases with increase in the elasticity in the fluid. It is also shown that wall shear stress depends only on suction and is also independent of the material of fluids. No steady solution for velocity distribution exists when there is blowing at the plate. Temperature distribution in the boundary layer is determined and it is found that temperature at a point decreases with increase in the elasticity in the fluid.
Abstract: In this paper a procedure for the split-pipe design of looped water distribution network based on the use of simulated annealing is proposed. Simulated annealing is a heuristic-based search algorithm, motivated by an analogy of physical annealing in solids. It is capable for solving the combinatorial optimization problem. In contrast to the split-pipe design that is derived from a continuous diameter design that has been implemented in conventional optimization techniques, the split-pipe design proposed in this paper is derived from a discrete diameter design where a set of pipe diameters is chosen directly from a specified set of commercial pipes. The optimality and feasibility of the solutions are found to be guaranteed by using the proposed method. The performance of the proposed procedure is demonstrated through solving the three well-known problems of water distribution network taken from the literature. Simulated annealing provides very promising solutions and the lowest-cost solutions are found for all of these test problems. The results obtained from these applications show that simulated annealing is able to handle a combinatorial optimization problem of the least cost design of water distribution network. The technique can be considered as an alternative tool for similar areas of research. Further applications and improvements of the technique are expected as well.
Abstract: Chevron frames (Inverted-V-braced frames or Vbraced
frames) have seismic disadvantages, such as not good exhibit force redistribution capability and compression brace buckles
immediately. Researchers developed new design provisions on
increasing both the ductility and lateral resistance of these structures
in seismic areas. One of these new methods is adding zipper columns, as proposed by Khatib et al. (1988) [2]. Zipper columns are
vertical members connecting the intersection points of the braces
above the first floor. In this paper applicability of the suspended
zipper system to Seismic Rehabilitation of Steel Structures is investigated.
The models are 3-, 6-, 9-, and 12-story Inverted-V-braced frames.
In this case, it is assumed that the structures must be rehabilitated. For rehabilitation of structures, zipper column is used. The result of
researches showed that the suspended zipper system is effective in
case of 3-, 6-, and 9-story Inverted-V-braced frames and it would
increase lateral resistance of structure up to life safety level. But in
case of high-rise buildings (such as 12 story frame), it doesn-t show
good performance. For solving this problem, the braced bay can
consist of small “units" over the height of the entire structure, which each of them is a zipper-braced bay with a few stories. By using this
method the lateral resistance of 12 story Inverted-V-braced frames is increased up to safety life level.
Abstract: Temperature dependence of force of gravitation is one
of the fundamental problems of physics. This problem has got special
value in connection with that the general theory of relativity,
supposing the weakest positive influence of a body temperature on its
weight, actually rejects an opportunity of measurement of negative
influence of temperature on gravity in laboratory conditions. Really,
the recognition of negative temperature dependence of gravitation,
for example, means basic impossibility of achievement of a
singularity («a black hole») at a gravitational collapse. Laboratory
experiments with exact weighing the heated up metal samples,
indicating negative influence temperatures of bodies on their physical
weight are described. Influence of mistakes of measurements is
analyzed. Calculations of distribution of temperature in volume of the
bar, agreed with experimental data of time dependence of weight of
samples are executed. The physical substantiation of negative
temperature dependence of weight of the bodies, based on correlation
of acceleration at thermal movement of micro-particles of a body and
its absolute temperature, are given.
Abstract: Wind power is among the most actively developing distributed generation (DG) technology. Majority of the wind power based DG technologies employ wind turbine induction generators (WTIG) instead of synchronous generators, for the technical advantages like: reduced size, increased robustness, lower cost, and increased electromechanical damping. However, dynamic changes of wind speed make the amount of active/reactive power injected/drawn to a WTIG embedded distribution network highly variable. This paper analyzes the effect of wind speed changes on the active and reactive power penetration to the wind energy embedded distribution network. Four types of wind speed changes namely; constant, linear change, gust change and random change of wind speed are considered in the analysis. The study is carried out by three-phase, non-linear, dynamic simulation of distribution system component models. Results obtained from the investigation are presented and discussed.
Abstract: A frictionless contact problem for a two-layer orthotropic elastic medium loaded through a rigid flat stamp is considered. It is assumed that tensile tractions are not allowed and only compressive tractions can be transmitted across the interface. In the solution, effect of gravity is taken into consideration. If the external load on the rigid stamp is less than or equal to a critical value, continuous contact between the layers is maintained. The problem is expressed in terms of a singular integral equation by using the theory of elasticity and the Fourier transforms. Numerical results for initial separation point, critical separation load and contact stress distribution are presented.
Abstract: The paper presents a complete discrete statistical framework, based on a novel vector quantization (VQ) front-end process. This new VQ approach performs an optimal distribution of VQ codebook components on HMM states. This technique that we named the distributed vector quantization (DVQ) of hidden Markov models, succeeds in unifying acoustic micro-structure and phonetic macro-structure, when the estimation of HMM parameters is performed. The DVQ technique is implemented through two variants. The first variant uses the K-means algorithm (K-means- DVQ) to optimize the VQ, while the second variant exploits the benefits of the classification behavior of neural networks (NN-DVQ) for the same purpose. The proposed variants are compared with the HMM-based baseline system by experiments of specific Arabic consonants recognition. The results show that the distributed vector quantization technique increase the performance of the discrete HMM system.
Abstract: This paper develops the fiscal health index of 21 local
governments in Taiwan over the 1984 to 2010 period. A quantile
regression analysis was used to explore the extent that economic
variables, political budget cycles, and legislative checks and balances,
impact different quantiles of fiscal health index for a country over a
sample period of time. Our findings suggest that local governments at
the lower quantile are significantly benefited from political budget
cycles and the increase in central government revenues, while
legislative effective checks and balances and the increase in central
government expenditures have a significantly negative effect on local
fiscal health. When local governments are in the upper tail of the
distribution, legislative checks and balances and growth in
macroeconomics have significant and adverse effects on the fiscal
health of local governments. However, increases in central
government revenues have significant and positive effects on the
health status of local government in Taiwan.
Abstract: A way of generating millimeter wave I/Q signal using inductive resonator matched poly-phase filter is suggested. Normally the poly-phase filter generates quite accurate I/Q phase and magnitude but the loss of the filter is considerable due to series connection of passive RC components. This loss term directly increases system noise figure when the poly-phase filter is used in RF Front-end. The proposed matching method eliminates above mentioned loss and in addition provides gain on the passive filter. The working algorithm is illustrated by mathematical analysis. The generated I/Q signal is used in implementing millimeter wave phase shifter for the 60 GHz communication system to verify its effectiveness. The circuit is fabricated in 90 nm TSMC RF CMOS process under 1.2 V supply voltage. The measurement results showed that the suggested method improved gain by 6.5 dB and noise by 2.3 dB. The summary of the proposed I/Q generation is compared with previous works.
Abstract: In this paper we propose a mixture of two different
distributions such as Exponential-Gamma, Exponential-Weibull and
Gamma-Weibull to model heterogeneous survival data. Various
properties of the proposed mixture of two different distributions are
discussed. Maximum likelihood estimations of the parameters are
obtained by using the EM algorithm. Illustrative example based on
real data are also given.
Abstract: This paper presents an exact analytical model for
optimizing stability of thin-walled, composite, functionally graded
pipes conveying fluid. The critical flow velocity at which divergence
occurs is maximized for a specified total structural mass in order to
ensure the economic feasibility of the attained optimum designs. The
composition of the material of construction is optimized by defining
the spatial distribution of volume fractions of the material
constituents using piecewise variations along the pipe length. The
major aim is to tailor the material distribution in the axial direction so
as to avoid the occurrence of divergence instability without the
penalty of increasing structural mass. Three types of boundary
conditions have been examined; namely, Hinged-Hinged, Clamped-
Hinged and Clamped-Clamped pipelines. The resulting optimization
problem has been formulated as a nonlinear mathematical
programming problem solved by invoking the MatLab optimization
toolbox routines, which implement constrained function
minimization routine named “fmincon" interacting with the
associated eigenvalue problem routines. In fact, the proposed
mathematical models have succeeded in maximizing the critical flow
velocity without mass penalty and producing efficient and economic
designs having enhanced stability characteristics as compared with
the baseline designs.
Abstract: Power loss reduction is one of the main targets in power industry and so in this paper, the problem of finding the optimal configuration of a radial distribution system for loss reduction is considered. Optimal reconfiguration involves the selection of the best set of branches to be opened ,one each from each loop, for reducing resistive line losses , and reliving overloads on feeders by shifting the load to adjacent feeders. However ,since there are many candidate switching combinations in the system ,the feeder reconfiguration is a complicated problem. In this paper a new approach is proposed based on a simple optimum loss calculation by determining optimal trees of the given network. From graph theory a distribution network can be represented with a graph that consists a set of nodes and branches. In fact this problem can be viewed as a problem of determining an optimal tree of the graph which simultaneously ensure radial structure of each candidate topology .In this method the refined genetic algorithm is also set up and some improvements of algorithm are made on chromosome coding. In this paper an implementation of the algorithm presented by [7] is applied by modifying in load flow program and a comparison of this method with the proposed method is employed. In [7] an algorithm is proposed that the choice of the switches to be opened is based on simple heuristic rules. This algorithm reduce the number of load flow runs and also reduce the switching combinations to a fewer number and gives the optimum solution. To demonstrate the validity of these methods computer simulations with PSAT and MATLAB programs are carried out on 33-bus test system. The results show that the performance of the proposed method is better than [7] method and also other methods.
Abstract: Network reconfiguration in distribution system is realized by changing the status of sectionalizing switches to reduce the power loss in the system. This paper presents a new method which applies an artificial bee colony algorithm (ABC) for determining the sectionalizing switch to be operated in order to solve the distribution system loss minimization problem. The ABC algorithm is a new population based metaheuristic approach inspired by intelligent foraging behavior of honeybee swarm. The advantage of ABC algorithm is that it does not require external parameters such as cross over rate and mutation rate as in case of genetic algorithm and differential evolution and it is hard to determine these parameters in prior. The other advantage is that the global search ability in the algorithm is implemented by introducing neighborhood source production mechanism which is a similar to mutation process. To demonstrate the validity of the proposed algorithm, computer simulations are carried out on 14, 33, and 119-bus systems and compared with different approaches available in the literature. The proposed method has outperformed the other methods in terms of the quality of solution and computational efficiency.
Abstract: EDF (Early Deadline First) algorithm is a very important scheduling algorithm for real- time systems . The EDF algorithm assigns priorities to each job according to their absolute deadlines and has good performance when the real-time system is not overloaded. When the real-time system is overloaded, many misdeadlines will be produced. But these misdeadlines are not uniformly distributed, which usually focus on some tasks. In this paper, we present an adaptive fuzzy control scheduling based on EDF algorithm. The improved algorithm can have a rectangular distribution of misdeadline ratios among all real-time tasks when the system is overloaded. To evaluate the effectiveness of the improved algorithm, we have done extensive simulation studies. The simulation results show that the new algorithm is superior to the old algorithm.
Abstract: We aimed to investigate how can target and optimize
pulmonary delivery distribution by changing physicochemical
characteristics of instilled liquid.Therefore, we created a new liquids
group:
a. eligible for desired distribution within lung because of
assorted physicochemical characteristics
b. capable of being augmented with a broad range of
chemicals inertly
c. no interference on respiratory function
d. compatible with airway surface liquid
We developed forty types of new liquid,were composed of
Carboxymethylcellulose sodium,Glycerin and different types of
Polysorbates.Viscosity was measured using a Programmable
Rheometer and surface tension by KRUSS Tensiometer.We
subsequently examined the liquids and delivery protocols by simple
and branched glass capillary tube models of airways.Eventually,we
explored pulmonary distribution of liquids being augmented with
technetium-99m in mechanically ventilated rabbits.We used a single
head large field of view gamma camera.Kinematic viscosity between
0.265Stokes and 0.289Stokes,density between 1g/cm3 and 1.5g/cm3
and surface tension between 25dyn/cm and 35dyn/cm were the most
acceptable.
Abstract: The purpose of this paper is to solve the problem of protecting aerial lines from high impedance faults (HIFs) in distribution systems. This investigation successfully applies 3I0 zero sequence current to solve HIF problems. The feature extraction system based on discrete wavelet transform (DWT) and the feature identification technique found on statistical confidence are then applied to discriminate effectively between the HIFs and the switch operations. Based on continuous wavelet transform (CWT) pattern recognition of HIFs is proposed, also. Staged fault testing results demonstrate that the proposed wavelet based algorithm is feasible performance well.
Abstract: The main objective of this paper is to analyse the influence of preparation and control of orders on performance. The focused activities explored in this research are: procurement, production and distribution. These changes in performance were obtained through improvement of the supply chain. It is proved using all the company activities that it is possible to increase de efficiency and do services in an adequate way, placing the products in the market efficiently. For that, it was explored the importance of the supply chain, with privilege to the practical environment and the quantification of the obtained results.
Abstract: This paper presents a experiment to estimate the
influences of cutting conditions in microstructure changes of
machining austenitic 304 stainless steel, especially for wear insert. The
wear insert were prefabricated with a width of 0.5 mm. And the forces,
temperature distribution, RS, and microstructure changes were
measured by force dynamometer, infrared thermal camera, X-ray
diffraction, XRD, SEM, respectively. The results told that the different
combinations of machining condition have a significant influence on
machined surface microstructure changes. In addition to that, the
ANOVA and AOMwere used to tell the different influences of cutting
speed, feed rate, and wear insert.