Abstract: In this research, the laminar heat transfer of natural convection on vertical surfaces has been investigated. Most of the studies on natural convection have been considered constantly whereas velocity and temperature domain, do not change with time, transient one are used a lot. Governing equations are solved using a finite volume approach. The convective terms are discretized using the power-law scheme, whereas for diffusive terms the central difference is employed. Coupling between the velocity and pressure is made with SIMPLE algorithm. The resultant system of discretized linear algebraic equations is solved with an alternating direction implicit scheme. Then a configuration of rectangular fins is put in different ways on the surface and heat transfer of natural convection on these surfaces without sliding is studied and finally optimization is done.
Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: Composite steel shear wall is a lateral load resisting system which consists of a steel plate with concrete wall attached to one or both sides to prevent it from elastic buckling. The composite behavior is ensured by utilizing high-strength bolts. This paper investigates the effect of distance between bolts, and for this purpose 14 one-story one-bay specimens with various bolts spacing were modeled by finite element code which is developed by the authors. To verify the model, numerical results were compared with a valid experiment which illustrate proper agreement. Results depict increasing the distance between bolts would improve the seismic ever, this increase must be limited, because of large distances will cause widespread buckling of the steel plate in free subpanels between bolts and would result in no improvement. By comparing the results in elastic region, it was observed initial stiffness is not affected by changing the distance.
Abstract: As one result of the project “Reactive Construction
Project Scheduling using Real Time Construction Logistic Data and
Simulation”, a procedure for using data about uncertain resource
availability assumptions in reactive scheduling processes has been
developed. Prediction data about resource availability is generated in
a formalized way using real-time monitoring data e.g. from auto-ID
systems on the construction site and in the supply chains. The paper
focusses on the formalization of the procedure for monitoring
construction logistic processes, for the detection of disturbance and
for generating of new and uncertain scheduling assumptions for the
reactive resource constrained simulation procedure that is and will be
further described in other papers.
Abstract: According to historical legend, after the revelation of the holy Qur'an, which gave the hijab compulsory and women were required to cover the head and body with a handkerchief, and the general form of clothing in her veil, Muslim women have begun to comply with this worthy tradition. This article discusses the history of the rise and spread of the hijab and its types. And here is described in detail types of hijab and its intended value, style hijab in different regions. Now wearing the hijab, hijab in general the problem is important not only in the Arab world, but also in the world.
Abstract: This paper presents a comparative study on
Vanadyl Phthalocyanine (VOPc) thin films deposited by thermal
evaporation and spin coating techniques. The samples
were prepared on cleaned glass substrates and annealed at
various temperatures ranging form 95oC to 155oC. To obtain
the morphological and structural properties of VOPc thin
films, X-ray diffraction (XRD) technique and atomic force
microscopy (AFM) have been implied. The AFM topographic
images show a very slight difference in the thermally grown
films, before and after annealing, however best results are
achieved for the spin-cast film annealed at 125oC. The XRD
spectra show no existence of the sharp peaks, suggesting the
material to be amorphous. The humps in the XRD patterns
indicate the presence of some crystallites.
Abstract: A finite element analysis was conducted to determine
the effect of moisture diffusion and hygroscopic swelling in rice. A
parallel simple stochastic modeling was performed to predict the
number of grains cracked as a result of moisture absorption and
hygroscopic swelling. Rice grains were soaked in thermally (25 oC)
controlled water and then tested for compressive stress. The
destructive compressive stress tests revealed through compressive
stress calculation that the peak force required to cause cracking in
grains soaked in water reduced with time as soaking duration was
extended. Results of the experiment showed that several grains had
their value of the predicted compressive stress below the von Mises
stress and were interpreted as grains which become cracked and/or
broke during soaking. The technique developed in this experiment
will facilitate the approximation of the number of grains which will
crack during soaking.
Abstract: Due to short product life cycles, increasing variety of
products and short cycles of leap innovations manufacturing
companies have to increase the flexibility of factory structures.
Flexibility of factory structures is based on defined factory planning
processes in which product, process and resource data of various
partial domains have to be considered. Thus factory planning
processes can be characterized as iterative, interdisciplinary and
participative processes [1]. To support interdisciplinary and
participative character of planning processes, a federative factory
data management (FFDM) as a holistic solution will be described.
FFDM is already implemented in form of a prototype. The interim
results of the development of FFDM will be shown in this paper. The
principles are the extracting of product, process and resource data
from documents of various partial domains providing as web services
on a server. The described data can be requested by the factory
planner by using a FFDM-browser.
Abstract: Training with Functional Electrical Stimulation (FES)
has both physiological and psychological benefits for spinal cord
injured subjects. Commonly used methods for quantification of
spasticity have shown controversial reliability. In this study we
propose a method for quick determination of spasticity in spinal cord
injured subjects on a cycling and measurement system. 23 patients
did training sessions on an instrumented mobile FES cycle three
times a week over two months as part of their clinical rehabilitation
program. Spasticity (MAS) and the legs resistance to the pedaling
motion were assessed before and after the FES training and
measurements were done on the subjects ability to pedal with our
without motor assistance. Measurements with test persons with
incomplete spastic paraplegia have shown that spasticity is decreased
after a 30 min cycling training with functional electrical stimulation
(FES).
Abstract: Pepper spray use has gained momentum since 1992
and although the active ingredient is readily available, it is considered
a weapon with restricted use in many regions, including The
Bahamas. In light of controversy in the literature regarding the
severity of presenting respiration complaints among individuals postacute
exposure of pepper spray inhalation, this descriptive case series
study was conducted to assess the respiratory status of persons
evaluated during a mass casualty in The Bahamas. Parameters noted
were patients- demographics and respiration severity determined via
clinical examination findings, disposition and follow-up review of the
20 persons. Their most common complaint was difficulty breathing
post exposure. Two required admission and stayed for
Abstract: The paper investigates the main issues concerning the activity of mergers and acquisitions in Romania in the period 2000- 2004. As in the first decade after the failure of the socialist economy the market of M&A was living its infancy based exclusively on privatization transactions, after 2000 the market entered in a stage of maturity. We are investigated both the registered evolutions in terms of number and value of transactions, and some sectoral issues, concerning the most important industries affected by the M&A process.
Abstract: Component-Based software engineering provides an
opportunity for better quality and increased productivity in software
development by using reusable software components [10]. One of the
most critical aspects of the quality of a software system is its
performance. The systematic application of software performance
engineering techniques throughout the development process can help
to identify design alternatives that preserve desirable qualities such
as extensibility and reusability while meeting performance objectives
[1]. In the present scenario, software engineering methodologies
strongly focus on the functionality of the system, while applying a
“fix- it-later" approach to software performance aspects [3]. As a
result, lengthy fine-tunings, expensive extra hard ware, or even
redesigns are necessary for the system to meet the performance
requirements. In this paper, we propose design based,
implementation independent, performance prediction approach to
reduce the overhead associated in the later phases while developing a
performance guaranteed software product with the help of Unified
Modeling Language (UML).
Abstract: This paper discusses the effectiveness of the EEG signal
for human identification using four or less of channels of two different
types of EEG recordings. Studies have shown that the EEG signal
has biometric potential because signal varies from person to person
and impossible to replicate and steal. Data were collected from 10
male subjects while resting with eyes open and eyes closed in 5
separate sessions conducted over a course of two weeks. Features
were extracted using the wavelet packet decomposition and analyzed
to obtain the feature vectors. Subsequently, the neural networks
algorithm was used to classify the feature vectors. Results show that,
whether or not the subjects- eyes were open are insignificant for a 4–
channel biometrics system with a classification rate of 81%. However,
for a 2–channel system, the P4 channel should not be included if data
is acquired with the subjects- eyes open. It was observed that for 2–
channel system using only the C3 and C4 channels, a classification
rate of 71% was achieved.
Abstract: This research analyzes factors affecting the success of
Litecoin Value within Thailand and develops a guideline for selfreliance
for effective business implementation. Samples in this study
included 119 people through surveys. The results revealed four main
factors affecting the success as follows: 1) Future Career training
should be pursued in applied Litecoin development. 2) Didn't grasp
the concept of a digital currency or see the benefit of a digital
currency. 3) There is a great need to educate the next generation of
learners on the benefits of Litecoin within the community. 4) A great
majority didn't know what Litecoin was.
The guideline for self-reliance planning consisted of 4 aspects: 1)
Development planning: by arranging meet up groups to conduct
further education on Litecoin and share solutions on adoption into
every day usage. Local communities need to develop awareness of
the usefulness of Litecoin and share the value of Litecoin among
friends and family. 2) Computer Science and Business Management
staff should develop skills to expand on the benefits of Litecoin
within their departments. 3) Further research should be pursued on
how Litecoin Value can improve business and tourism within
Thailand. 4) Local communities should focus on developing Litecoin
awareness by encouraging street vendors to accept Litecoin as
another form of payment for services rendered.
Abstract: To investigate the production of cellulases from Aspergillus heteromorphus, submerged fermentation was performed using wheat straw as substrate. Optimization of saccharification conditions like pH, temperature and time were studied. Highest reducing sugar was released on 5th day at 5 pH, 30° C temperature. When A. heteromorphous was grown on wheat straw in submerged fermentation after 5 days incubation at 30 ° C, 3.2 IU/ml and 83 IU/ml, filter paper activity and CMCase activity respectively.
Abstract: Social, mobility and information aggregation inside
business environment need to converge to reach the next step of
collaboration to enhance interaction and innovation. The following
article is based on the “Assemblage" concept seen as a framework to
formalize new user interfaces and applications. The area of research
is the Energy Social Business Environment, especially the Energy
Smart Grids, which are considered as functional and technical
foundations of the revolution of the Energy Sector of tomorrow. The
assemblages are modelized by means of mereology and simplicial
complexes. Its objective is to offer new central attention and
decision-making tools to end-users.
Abstract: Study fluid flow and heat transfer characteristics of
microchannel in a primary Cross-corrugated(CC) surface recuperators
with corrugations and without corrugations, using CFD method. The
pitch-over-height ratios P/H of Cross-corrugated (CC) surface is from
1.5 to 4.0, included angles β=75º. The study was performed using CFD
software FLUENT to create unit model and simulate fluid
temperature, velocity, heat transfer coefficient and other parameters.
The results from these simulations were compared to experimental
data. It is concluded that, when the Reynolds number is constant, if
increase P/H, j/f will decrease, also the decreasing trend will become
weak. Under the condition of P/H=2.2, if increase the inlet velocity j/f
will decrease; in addition, the heat transfer performance in surface
with corrugation will increase 10% compared to that without
corrugation. The study results can provide the basis to optimize the
design, select the type of heat transfer surface, the scale structure, and
heat-transfer surface arrangement for recuperators.
Abstract: The report focuses on such an important indicator of the nature and direction of development of ethnic and cultural processes in the Republic of Kazakhstan, as ethno linguistic situation. It is shown that, in essence, on the one hand, expresses the degree of the actual propagation and the level of use of the languages of the various ethnic communities. On the other hand, reflects the important patterns, trends and prospects of ethno-cultural and ethnodemographic processes in the Republic. It is important to note that the ethno linguistic situation in different regions of Kazakhstan, due to its more dynamic and much more difficult to demonstrate a much greater variety of options when compared with the ethnic situation in the country. For the two major ethnic groups of the republic – Kazakh and Russian language ethno differentiating retains its value, while for the other ethnic groups observed decline in the importance of this indicator. As you know, the language of international communication in the country is Russian. As the censuses of population, the Russian language in many areas of Northern, Central and Eastern Kazakhstan becomes a means of ethno linguistic development for most of the non-Russian population. This is most clearly illustrated by the Germans, and the Slavic ethnic groups. In this case, the Russian language is not just a means of international communication for a number of ethnic groups, and ethnic groups, it becomes a factor of ethnic self-expression. The value of the Kazakh language as their mother tongue for the other groups of the population is small. More clearly it can be traced only to the Turkic-speaking population of the republic – Uzbeks, Uighurs, Tatars, Turks, etc. The state Kazakh language is a means of international communication in the Western and Southern Kazakhstan, with a predominance of the Kazakh population. The report shows that the most important factor in the development of ethno-linguistic and ethno-cultural processes is bilingualism. Comparative analysis of materials census shows, first, on the increase of the proportion of bilingual population among Kazakhs and Russian, and second, to reduce the proportion of bilingual population of other ethnic groups living in Kazakhstan, and third, a higher proportion bilingual population among residents than rural residents, regardless of their ethnicity. Bilingualism is mainly of a "national Kazakh", "national Russian" or "Kazakh-national" or "Russian-national" character. The President N.A. Nazarbayev said that the Kazakh language is the most important factor in the consolidation of the people of Kazakhstan. He therefore called on government and other state and local representative bodies fully develop the state language, to create all the necessary organizational, material and technical conditions for free and open learning the state language by all citizens of the Republic of Kazakhstan.
Abstract: The paper presents the design concept of a unitselection
text-to-speech synthesis system for the Slovenian language.
Due to its modular and upgradable architecture, the system can be
used in a variety of speech user interface applications, ranging from
server carrier-grade voice portal applications, desktop user interfaces
to specialized embedded devices.
Since memory and processing power requirements are important
factors for a possible implementation in embedded devices, lexica
and speech corpora need to be reduced. We describe a simple and
efficient implementation of a greedy subset selection algorithm that
extracts a compact subset of high coverage text sentences. The
experiment on a reference text corpus showed that the subset
selection algorithm produced a compact sentence subset with a small
redundancy.
The adequacy of the spoken output was evaluated by several
subjective tests as they are recommended by the International
Telecommunication Union ITU.
Abstract: In the present work, a comparative study on the
microstructure and mechanical properties of as cast, cast aged and
forged aged A356 alloy has been investigated. The study reveals that
mechanical properties of A356 alloy are highly influenced by melt
treatment and solid state processing. Cast aged alloys achieve highest
strength and hardness compared to as cast and forge aged ones. Ones
treated with combined addition of grain refiners and modifiers
achieve maximum strength and hardness. Cast aged A356 alloy
possesses higher wear resistance compared to as cast and forge aged
ones. Forging improves both strength and ductility of alloys over as
cast ones. However, the improvement in ductility is perceptible only
for properly grain refined and modified alloys. Ones refined with
0.65% Al-3Ti shows highest improvement in ductility while ones
treated with 0.20% Al-10Sr exhibits less improvement in ductility.