Abstract: Thermal load calculations have been performed for
multi-layered walls that are composed of three different parts; a
common (sand and cement) plaster, and two types of locally
produced soft and hard bricks. The masonry construction of these
layered walls was based on concrete-backed stone masonry made of
limestone bricks joined by mortar. These multilayered walls are
forming the outer walls of the building envelope of a typical Libyan
house. Based on the periodic seasonal weather conditions, within the
Libyan cost region during summer and winter, measured thermal
conductivity values were used to implement such seasonal variation
of heat flow and the temperature variations through the walls. The
experimental measured thermal conductivity values were obtained
using the Hot Disk technique. The estimation of the thermal
resistance of the wall layers ( R-values) is based on measurements
and calculations. The numerical calculations were done using a
simplified analytical model that considers two different wall
constructions which are characteristics of such houses. According to
the obtained results, the R-values were quite low and therefore,
several suggestions have been proposed to improve the thermal
loading performance that will lead to a reasonable human comfort
and reduce energy consumption.
Abstract: Analytical seismic response of multi-story building
supported on base isolation system is investigated under real
earthquake motion. The superstructure is idealized as a shear type
flexible building with lateral degree-of-freedom at each floor. The
force-deformation behaviour of the isolation system is modelled by
the bi-linear behaviour which can be effectively used to model all
isolation systems in practice. The governing equations of motion of
the isolated structural system are derived. The response of the system
is obtained numerically by step-by-method under three real recorded
earthquake motions and pulse motions associated in the near-fault
earthquake motion. The variation of the top floor acceleration, interstory
drift, base shear and bearing displacement of the isolated
building is studied under different initial stiffness of the bi-linear
isolation system. It was observed that the high initial stiffness of the
isolation system excites higher modes in base-isolated structure and
generate floor accelerations and story drift. Such behaviour of the
base-isolated building especially supported on sliding type of
isolation systems can be detrimental to sensitive equipment installed
in the building. On the other hand, the bearing displacement and base
shear found to reduce marginally with the increase of the initial
stiffness of the initial stiffness of the isolation system. Further, the
above behaviour of the base-isolated building was observed for
different parameters of the bearing (i.e. post-yield stiffness and
characteristic strength) and earthquake motions (i.e. real time history
as well as pulse type motion).
Abstract: The present energy situation and the concerns
about global warming has stimulated active research interest
in non-petroleum, carbon free compounds and non-polluting
fuels, particularly for transportation, power generation, and
agricultural sectors. Environmental concerns and limited
amount of petroleum fuels have caused interests in the
development of alternative fuels for internal combustion (IC)
engines. The petroleum crude reserves however, are declining
and consumption of transport fuels particularly in the
developing countries is increasing at high rates. Severe
shortage of liquid fuels derived from petroleum may be faced
in the second half of this century. Recently more and more
stringent environmental regulations being enacted in the USA
and Europe have led to the research and development
activities on clean alternative fuels. Among the gaseous fuels
hydrogen is considered to be one of the clean alternative fuel.
Hydrogen is an interesting candidate for future internal
combustion engine based power trains. In this experimental
investigation, the performance and combustion analysis were
carried out on a direct injection (DI) diesel engine using
hydrogen with diesel following the TMI(Time Manifold
Injection) technique at different injection timings of 10
degree,45 degree and 80 degree ATDC using an electronic
control unit (ECU) and injection durations were controlled.
Further, the tests have been carried out at a constant speed of
1500rpm at different load conditions and it can be observed
that brake thermal efficiency increases with increase in load
conditions with a maximum gain of 15% at full load
conditions during all injection strategies of hydrogen. It was
also observed that with the increase in hydrogen energy share
BSEC started reducing and it reduced to a maximum of 9% as
compared to baseline diesel at 10deg ATDC injection during
maximum injection proving the exceptional combustion
properties of hydrogen.
Abstract: Graduate attributes have received increasing attention
over recent years as universities incorporate these attributes into the
curriculum. Graduates who have adequate technical knowledge only
are not sufficiently equipped to compete effectively in the work
place; they also need non disciplinary skills ie, graduate attributes.
The purpose of this paper is to investigate the impact of an eportfolio
in a technical communication course to enhance engineering
students- graduate attributes: namely, learning of communication,
critical thinking and problem solving and teamwork skills. Two
questionnaires were used to elicit information from the students: one
on their preferred and the other on the actual learning process. In
addition, student perceptions of the use of eportfolio as a learning
tool were investigated. Preliminary findings showed that most of the
students- expectations have been met with their actual learning. This
indicated that eportfolio has the potential as a tool to enhance
students- graduate attributes.
Abstract: In this paper, we will present an architecture for the
implementation of a real time stereoscopic images correction's
approach. This architecture is parallel and makes use of several
memory blocs in which are memorized pre calculated data relating to
the cameras used for the acquisition of images. The use of reduced
images proves to be essential in the proposed approach; the
suggested architecture must so be able to carry out the real time
reduction of original images.
Abstract: A stage-structured predator-prey system with two time delays is considered. By analyzing the corresponding characteristic equation, the local stability of a positive equilibrium is investigated and the existence of Hopf bifurcations is established. Formulae are derived to determine the direction of bifurcations and the stability of bifurcating periodic solutions by using the normal form theory and center manifold theorem. Numerical simulations are carried out to illustrate the theoretical results. Based on the global Hopf bifurcation theorem for general functional differential equations, the global existence of periodic solutions is established.
Abstract: The distressing flood scenarios that occur in
recent years at the surrounding areas of Sarawak River have
left damages of properties and indirectly caused disruptions of
productive activities. This study is meant to reconstruct a 100-year
flood event that took place in this river basin. Sarawak River Subbasin
was chosen and modeled using the one-dimensional
hydrodynamic modeling approach using InfoWorks River Simulation
(RS), in combination with Geographical Information System (GIS).
This produces the hydraulic response of the river and its floodplains
in extreme flooding conditions. With different parameters introduced
to the model, correlations of observed and simulated data are
between 79% – 87%. Using the best calibrated model, flood
mitigation structures are imposed along the sub-basin. Analysis is
done based on the model simulation results. Result shows that the
proposed retention ponds constructed along the sub-basin provide the
most efficient reduction of flood by 34.18%.
Abstract: The necessity of solving multi dimensional
complicated scientific problems beside the necessity of several
objective functions optimization are the most motive reason of born
of artificial intelligence and heuristic methods.
In this paper, we introduce a new method for multiobjective
optimization based on learning automata. In the proposed method,
search space divides into separate hyper-cubes and each cube is
considered as an action. After gathering of all objective functions
with separate weights, the cumulative function is considered as the
fitness function. By the application of all the cubes to the cumulative
function, we calculate the amount of amplification of each action and
the algorithm continues its way to find the best solutions. In this
Method, a lateral memory is used to gather the significant points of
each iteration of the algorithm. Finally, by considering the
domination factor, pareto front is estimated. Results of several
experiments show the effectiveness of this method in comparison
with genetic algorithm based method.
Abstract: In this paper, we argue the security protocols of
ZigBee wireless sensor network in MAC layer. AES 128-bit
encryption algorithm in CCM* mode is secure transferred data;
however, AES-s secret key will be break within nearest future.
Efficient public key algorithm, ECC has been mixed with AES to
rescue the ZigBee wireless sensor from cipher text and replay attack.
Also, the proposed protocol can parallelize the integrity function to
increase system performance.
Abstract: Regenerative Thermal Oxidizer (RTO) is one of the
best solutions for removal of Volatile Organic Compounds (VOC)
from industrial processes. In the RTO, VOC in a raw gas are usually
decomposed at 950-1300 K and the combustion heat of VOC is
recovered by regenerative heat exchangers charged with ceramic
honeycombs. The optimization of the treatment of VOC leads to the
reduction of fuel addition to VOC decomposition, the minimization of
CO2 emission and operating cost as well.
In the present work, the thermal efficiency of the RTO was
investigated experimentally in a pilot-scale RTO unit using toluene as
a typical representative of VOC. As a result, it was recognized that the
radiative heat transfer was dominant in the preheating process of a raw
gas when the gas flow rate was relatively low. Further, it was found
that a minimum heat exchanger volume to achieve self combustion of
toluene without additional heating of the RTO by fuel combustion was
dependent on both the flow rate of a raw gas and the concentration of
toluene. The thermal efficiency calculated from fuel consumption and
the decomposed toluene ratio, was found to have a maximum value of
0.95 at a raw gas mass flow rate of 1810 kg·h-1 and honeycombs height
of 1.5m.
Abstract: In the present paper, we use generalized B-Spline curve in trigonometric form on circular domain, to capture the transcendental nature of circle involute curve and uncertainty characteristic of design. The required involute curve get generated within the given tolerance limit and is useful in gear design.
Abstract: In this paper we propose a new criterion for solving
the problem of channel shortening in multi-carrier systems. In a
discrete multitone receiver, a time-domain equalizer (TEQ) reduces
intersymbol interference (ISI) by shortening the effective duration of
the channel impulse response. Minimum mean square error (MMSE)
method for TEQ does not give satisfactory results. In [1] a new
criterion for partially equalizing severe ISI channels to reduce the
cyclic prefix overhead of the discrete multitone transceiver (DMT),
assuming a fixed transmission bandwidth, is introduced. Due to
specific constrained (unit morm constraint on the target impulse
response (TIR)) in their method, the freedom to choose optimum
vector (TIR) is reduced. Better results can be obtained by avoiding
the unit norm constraint on the target impulse response (TIR). In
this paper we change the cost function proposed in [1] to the cost
function of determining the maximum of a determinant subject to
linear matrix inequality (LMI) and quadratic constraint and solve the
resulting optimization problem. Usefulness of the proposed method
is shown with the help of simulations.
Abstract: Extracting and elaborating software requirements and
transforming them into viable software architecture are still an
intricate task. This paper defines a solution architecture which is
based on the blurred amalgamation of problem space and solution
space. The dependencies between domain constraints, requirements
and architecture and their importance are described that are to be
considered collectively while evolving from problem space to
solution space. This paper proposes a revised version of Twin Peaks
Model named Win Peaks Model that reconciles software
requirements and architecture in more consistent and adaptable
manner. Further the conflict between stakeholders- win-requirements
is resolved by proposed Voting methodology that is simple
adaptation of win-win requirements negotiation model and QARCC.
Abstract: Vehicle which are turning or maneuvering at high speeds
are susceptible to sliding and subsequently deviate from desired path. In
this paper the dynamics governing the Yaw/Roll behavior of a vehicle
has been simulated. Two different simulations have been used one for
the real vehicle, for which a fuzzy controller is designed to increase its
directional stability property. The other simulation is for a hypothetical
vehicle with much higher tire cornering stiffness which is capable of
developing the required lateral forces at the tire-ground patch contact to
attain the desired lateral acceleration for the vehicle to follow the
desired path without slippage. This simulation model is our reference
model.
The logic for keeping the vehicle on the desired track in the cornering
or maneuvering state is to have some braking forces on the inner or
outer tires based on the direction of vehicle deviation from the desired
path. The inputs to our vehicle simulation model is steer angle δ and
vehicle velocity V , and the outputs can be any kinematical parameters
like yaw rate, yaw acceleration, side slip angle, rate of side slip angle
and so on. The proposed fuzzy controller is a feed forward controller.
This controller has two inputs which are steer angle δ and vehicle
velocity V, and the output of the controller is the correcting moment M,
which guides the vehicle back to the desired track. To develop the
membership functions for the controller inputs and output and the fuzzy
rules, the vehicle simulation has been run for 1000 times and the
correcting moment have been determined by trial and error. Results of
the vehicle simulation with fuzzy controller are very promising
and show the vehicle performance is enhanced greatly over the
vehicle without the controller. In fact the vehicle performance
with the controller is very near the performance of the reference
ideal model.
Abstract: In areas of low to moderate seismicity many building contents and equipment are not positively fixed to the floor or tied to adjacent walls. Under seismic induced horizontal vibration, such contents and equipment can suffer from damage by either overturning or impact associated with rocking. This paper focuses on the estimation of shock on typical contents and equipment due to rocking. A simplified analytical model is outlined that can be used to estimate the maximum acceleration on a rocking object given its basic geometric and mechanical properties. The developed model was validated against experimental results. The experimental results revealed that the maximum shock acceleration can be underestimated if the static stiffness of the materials at the interface between the rocking object and floor is used rather than the dynamic stiffness. Excellent agreement between the model and experimental results was found when the dynamic stiffness for the interface material was used, which was found to be generally much higher than corresponding static stiffness under different investigated boundary conditions of the cushion. The proposed model can be a beneficial tool in performing a rapid assessment of shock sensitive components considered for possible seismic rectification.
Abstract: In order to upgrade the seismic resistibility of structures and enhance the functionality of an isolator, a new base isolator called the multiple trench friction pendulum system (MTFPS) is proposed in this study. The proposed MTFPS isolator is composed of a trench concave surface and several intermediate sliding plates in two orthogonal directions. Mathematical formulations have been derived to examine the characteristics of the proposed MTFPS isolator possessing multiple intermediate sliding plates. By means of mathematical formulations, it can be inferred that the natural period and damping effect of the MTFPS isolator with several intermediate sliding plates can be altered continually and controllably during earthquakes. Furthermore, results obtained from shaking table tests demonstrate that the proposed isolator provides good protection to structures for prevention of damage from strong earthquakes.
Abstract: This paper provides the design steps of a robust Linear
Matrix Inequality (LMI) based iterative multivariable PID controller
whose duty is to drive a sample power system that comprises a
synchronous generator connected to a large network via a step-up
transformer and a transmission line. The generator is equipped with
two control-loops, namely, the speed/power (governor) and voltage
(exciter). Both loops are lumped in one where the error in the
terminal voltage and output active power represent the controller
inputs and the generator-exciter voltage and governor-valve position
represent its outputs. Multivariable PID is considered here because of
its wide use in the industry, simple structure and easy
implementation. It is also preferred in plants of higher order that
cannot be reduced to lower ones. To improve its robustness to
variation in the controlled variables, H∞-norm of the system transfer
function is used. To show the effectiveness of the controller, divers
tests, namely, step/tracking in the controlled variables, and variation
in plant parameters, are applied. A comparative study between the
proposed controller and a robust H∞ LMI-based output feedback is
given by its robustness to disturbance rejection. From the simulation
results, the iterative multivariable PID shows superiority.
Abstract: Dengue virus is transmitted from person to person
through the biting of infected Aedes Aegypti mosquitoes. DEN-1,
DEN-2, DEN-3 and DEN-4 are four serotypes of this virus. Infection
with one of these four serotypes apparently produces permanent
immunity to it, but only temporary cross immunity to the others. The
length of time during incubation of dengue virus in human and
mosquito are considered in this study. The dengue patients are
classified into infected and infectious classes. The infectious human
can transmit dengue virus to susceptible mosquitoes but infected
human can not. The transmission model of this disease is formulated.
The human population is divided into susceptible, infected, infectious
and recovered classes. The mosquito population is separated into
susceptible, infected and infectious classes. Only infectious
mosquitoes can transmit dengue virus to the susceptible human. We
analyze this model by using dynamical analysis method. The
threshold condition is discussed to reduce the outbreak of this
disease.
Abstract: In this paper, a novel method for recognition of musical
instruments in a polyphonic music is presented by using an
embedded hidden Markov model (EHMM). EHMM is a doubly
embedded HMM structure where each state of the external HMM
is an independent HMM. The classification is accomplished for
two different internal HMM structures where GMMs are used as
likelihood estimators for the internal HMMs. The results are compared
to those achieved by an artificial neural network with two
hidden layers. Appropriate classification accuracies were achieved
both for solo instrument performance and instrument combinations
which demonstrates that the new approach outperforms the similar
classification methods by means of the dynamic of the signal.
Abstract: Losses reduction initiatives in distribution systems
have been activated due to the increasing cost of supplying
electricity, the shortage in fuel with ever-increasing cost to produce
more power, and the global warming concerns. These initiatives have
been introduced to the utilities in shape of incentives and penalties.
Recently, the electricity distribution companies in Oman have been
incentivized to reduce the distribution technical and non-technical
losses with an equal annual reduction rate for 6 years. In this paper,
different techniques for losses reduction in Mazoon Electricity
Company (MZEC) are addressed. In this company, high numbers of
substation and feeders were found to be non-compliant with the
Distribution System Security Standard (DSSS). Therefore, 33
projects have been suggested to bring non-complying 29 substations
and 28 feeders to meet the planed criteria and to comply with the
DSSS. The largest part of MZEC-s network (South Batinah region)
was modeled by ETAP software package. The model has been
extended to implement the proposed projects and to examine their
effects on losses reduction. Simulation results have shown that the
implementation of these projects leads to a significant improvement
in voltage profile, and reduction in the active and the reactive power
losses. Finally, the economical analysis has revealed that the
implementation of the proposed projects in MZEC leads to an annual
saving of about US$ 5 million.