Abstract: Creep stresses and strain rates have been obtained
for a thin rotating disc having variable density with inclusion by
using Seth-s transition theory. The density of the disc is assumed to
vary radially, i.e. ( ) 0 ¤ü ¤ü r/b m - = ; ¤ü 0 and m being real positive
constants. It has been observed that a disc, whose density increases
radially, rotates at higher angular speed, thus decreasing the
possibility of a fracture at the bore, whereas for a disc whose
density decreases radially, the possibility of a fracture at the bore
increases.
Abstract: In this study we investigate silica nanoparticle (SiO2- NP) effects on the structure and phase properties of supported lipid monolayers and bilayers, coupling surface pressure measurements, fluorescence microscopy and atomic force microscopy. SiO2-NPs typically in size range of 10nm to 100 nm in diameter are tested. Our results suggest first that lipid molecules organization depends to their nature. Secondly, lipid molecules in the vinicity of big aggregates nanoparticles organize in liquid condensed phase whereas small aggregates are localized in both fluid liquid-expanded (LE) and liquid-condenced (LC). We demonstrated also by atomic force microscopy that by measuring friction forces it is possible to get information as if nanoparticle aggregates are recovered or not by lipid monolayers and bilayers.
Abstract: In this paper, we present parallel alternating two-stage methods for solving linear system Ax = b, where A is a monotone matrix or an H-matrix. And we give some convergence results of these methods for nonsingular linear system.
Abstract: Recently, neural networks have shown good
results for detection of a certain pattern in a given image. In
our previous papers [1-5], a fast algorithm for pattern
detection using neural networks was presented. Such
algorithm was designed based on cross correlation in the
frequency domain between the input image and the weights
of neural networks. Image conversion into symmetric shape
was established so that fast neural networks can give the
same results as conventional neural networks. Another
configuration of symmetry was suggested in [3,4] to improve
the speed up ratio. In this paper, our previous algorithm for
fast neural networks is developed. The frequency domain
cross correlation is modified in order to compensate for the
symmetric condition which is required by the input image.
Two new ideas are introduced to modify the cross correlation
algorithm. Both methods accelerate the speed of the fast
neural networks as there is no need for converting the input
image into symmetric one as previous. Theoretical and
practical results show that both approaches provide faster
speed up ratio than the previous algorithm.
Abstract: This paper describes how the correct endian mode of
the TMS320C6713 DSK board can be identified. It also explains how
the TMS320C6713 DSK board can be used in the little endian and in
the big endian modes for assembly language programming in
particular and for signal processing in general. Similarly, it discusses
how crucially important it is for a user of the TMS320C6713 DSK
board to identify the mode of operation and then use it correctly
during the development stages of the assembly language
programming; otherwise, it will cause unnecessary confusion and
erroneous results as far as storing data into the memory and loading
data from the memory is concerned. Furthermore, it highlights and
strongly recommends to the users of the TMS320C6713 DSK board
to be aware of the availability and importance of various display
options in the Code Composer Studio (CCS) for correctly
interpreting and displaying the desired data in the memory. The
information presented in this paper will be of great importance and
interest to those practitioners and developers who wants to use the
TMS320C6713 DSK board for assembly language programming as
well as input-output signal processing manipulations. Finally,
examples that clearly illustrate the concept are presented.
Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: Buildings and associated construction methods have a significant impact on the environment. As construction activity increases in Kuwait, there is a need to create design and construction strategies which will minimize the environmental impact of new buildings. Green construction is a design philosophy intended to improve the sustainability of construction by the minimization of resource depletion and CO2 emissions throughout the life cycle of buildings. This paper presents and discusses the results of a survey that was conducted in Kuwait, with the objective of investigating the awareness of developers and other stakeholders regarding their understanding and use of green construction strategies. The results of the survey demonstrate that whilst there seems to be a reasonable level of awareness amongst the stakeholders, this awareness is not currently well reflected in the design and construction practices actually being applied. It is therefore concluded is there is a pressing need for intervention from Government in order that the use of sustainable green design and construction strategies becomes the norm in Kuwait.
Abstract: In a product development process, understanding the functional behavior of the system, the role of components in achieving functions and failure modes if components/subsystem fails its required function will help develop appropriate design validation and verification program for reliability assessment. The integration of these three issues will help design and reliability engineers in identifying weak spots in design and planning future actions and testing program. This case study demonstrate the advantage of unascertained theory described in the subjective cognition uncertainty, and then applies blind number (BN) theory in describing the uncertainty of the mechanical system failure process and the same time used the same theory in bringing out another mechanical reliability system model. The practical calculations shows the BN Model embodied the characters of simply, small account of calculation but betterforecasting capability, which had the value of macroscopic discussion to some extent.
Abstract: In this paper, we proposed an efficient data
compression strategy exploiting the multi-resolution characteristic of
the wavelet transform. We have developed a sensor node called
“Smart Sensor Node; SSN". The main goals of the SSN design are
lightweight, minimal power consumption, modular design and robust
circuitry. The SSN is made up of four basic components which are a
sensing unit, a processing unit, a transceiver unit and a power unit.
FiOStd evaluation board is chosen as the main controller of the SSN
for its low costs and high performance. The software coding of the
implementation was done using Simulink model and MATLAB
programming language. The experimental results show that the
proposed data compression technique yields recover signal with good
quality. This technique can be applied to compress the collected data
to reduce the data communication as well as the energy consumption
of the sensor and so the lifetime of sensor node can be extended.
Abstract: This paper introduces an adiabatic register file based
on two-phase CPAL (Complementary Pass-Transistor Adiabatic
Logic circuits) with power-gating scheme, which can operate on a
single-phase power clock. A 32×32 single-phase adiabatic register file
with power-gating scheme has been implemented with TSMC 0.18μm
CMOS technology. All the circuits except for the storage cells employ
two-phase CPAL circuits, and the storage cell is based on the
conventional memory one. The two-phase non-overlap power-clock
generator with power-gating scheme is used to supply the proposed
adiabatic register file. Full-custom layouts are drawn. The energy and
functional simulations have been performed using the net-list
extracted from their layouts. Compared with the traditional static
CMOS register file, HSPICE simulations show that the proposed
adiabatic register file can work very well, and it attains about 73%
energy savings at 100 MHz.
Abstract: This paper describes a low-voltage and low-power
channel selection analog front end with continuous-time low pass
filters and highly linear programmable gain amplifier (PGA). The
filters were realized as balanced Gm-C biquadratic filters to achieve a
low current consumption. High linearity and a constant wide
bandwidth are achieved by using a new transconductance (Gm) cell.
The PGA has a voltage gain varying from 0 to 65dB, while
maintaining a constant bandwidth. A filter tuning circuit that requires
an accurate time base but no external components is presented.
With a 1-Vrms differential input and output, the filter achieves
-85dB THD and a 78dB signal-to-noise ratio. Both the filter and PGA
were implemented in a 0.18um 1P6M n-well CMOS process. They
consume 3.2mW from a 1.8V power supply and occupy an area of
0.19mm2.
Abstract: As originally designed for wired networks, TCP (transmission control protocol) congestion control mechanism is triggered into action when packet loss is detected. This implicit assumption for packet loss mostly due to network congestion does not work well in Mobile Ad Hoc Network, where there is a comparatively high likelihood of packet loss due to channel errors and node mobility etc. Such non-congestion packet loss, when dealt with by congestion control mechanism, causes poor TCP performance in MANET. In this study, we continue to investigate the impact of the interaction between transport protocols and on-demand routing protocols on the performance and stability of 802.11 multihop networks. We evaluate the important wireless networking events caused routing change, and propose a cross layer method to delay the unnecessary routing changes, only need to add a sensitivity parameter α , which represents the on-demand routing-s reaction to link failure of MAC layer. Our proposal is applicable to the plain 802.11 networking environment, the simulation results that this method can remarkably improve the stability and performance of TCP without any modification on TCP and MAC protocol.
Abstract: The aim of this study was to investigate the correlation
between Facebook involvement and internet addiction. We sampled
577 university students in Taiwan and administered a survey of
Facebook usage, Facebook involvement scale (FIS), and internet
addiction scale. The FIS comprises three factors (salience, emotional
support, and amusement). Results showed that the Facebook
involvement scale had good reliability and validity. The correlation
between Facebook involvement and internet addiction was measured
at .395. This means that a higher degree of Facebook involvement
indicates a greater degree of psychological dependency on the internet,
and a greater propensity towards social withdrawal and other negative
psychological consequences associated with internet addiction.
Besides, the correlations between three factors of FIS (salience,
emotional support, and amusement) and internet addiction ranged
from .313-372, indicating that these neither of these factors (salience,
emotional support, and amusement) is more effective than the others in
predicting internet dependency.
Abstract: Although agriculture is an important part of the world
economy, accounting in agriculture still has many shortcomings. The
adoption of IAS 41 “Agriculture” has tried to improve this situation
and increase the comparability of financial statements of entities in
the agricultural sector. Although controversial, IAS 41 is the first
step of a consistent transition to fair value assessment in the
agricultural sector. The objective of our work is the analysis of IAS
41 and current accounting agricultural situation in Romania.
Accounting regulations in Romania are in accordance with European
directives and, in many respects, converged with IFRS referential.
Provisions of IAS 41, however, are not reflected directly in
Romanian regulations. With the increase of forest land transactions,
it is expected that recognition and measurement of biological assets
under IAS 41 to become a necessity.
Abstract: This paper presents a methodology towards the emulation of the electrical power consumption of the RF device during the cellular phone/handset transmission mode using the LTE technology. The emulation methodology takes the physical environmental variables and the logical interface between the baseband and the RF system as inputs to compute the emulated power dissipation of the RF device. The emulated power, in between the measured points corresponding to the discrete values of the logical interface parameters is computed as a polynomial interpolation using polynomial basis functions. The evaluation of polynomial and spline curve fitting models showed a respective divergence (test error) of 8% and 0.02% from the physically measured power consumption. The precisions of the instruments used for the physical measurements have been modeled as intervals. We have been able to model the power consumption of the RF device operating at 5MHz using homotopy between 2 continuous power consumptions of the RF device operating at the bandwidths 3MHz and 10MHz.
Abstract: In this paper, we have developed a method to
compute fractal dimension (FD) of discrete time signals, in the
time domain, by modifying the box-counting method. The size
of the box is dependent on the sampling frequency of the
signal. The number of boxes required to completely cover the
signal are obtained at multiple time resolutions. The time
resolutions are made coarse by decimating the signal. The loglog
plot of total number of boxes required to cover the curve
versus size of the box used appears to be a straight line, whose
slope is taken as an estimate of FD of the signal. The results
are provided to demonstrate the performance of the proposed
method using parametric fractal signals. The estimation
accuracy of the method is compared with that of Katz, Sevcik,
and Higuchi methods. In addition, some properties of the FD
are discussed.
Abstract: Electromyography (EMG) signal processing has been investigated remarkably regarding various applications such as in rehabilitation systems. Specifically, wavelet transform has served as a powerful technique to scrutinize EMG signals since wavelet transform is consistent with the nature of EMG as a non-stationary signal. In this paper, the efficiency of wavelet transform in surface EMG feature extraction is investigated from four levels of wavelet decomposition and a comparative study between different mother wavelets had been done. To recognize the best function and level of wavelet analysis, two evaluation criteria, scatter plot and RES index are recruited. Hereupon, four wavelet families, namely, Daubechies, Coiflets, Symlets and Biorthogonal are studied in wavelet decomposition stage. Consequently, the results show that only features from first and second level of wavelet decomposition yields good performance and some functions of various wavelet families can lead to an improvement in separability class of different hand movements.
Abstract: Personal name matching system is the core of
essential task in national citizen database, text and web mining,
information retrieval, online library system, e-commerce and record
linkage system. It has necessitated to the all embracing research in
the vicinity of name matching. Traditional name matching methods
are suitable for English and other Latin based language. Asian
languages which have no word boundary such as Myanmar language
still requires sounds alike matching system in Unicode based
application. Hence we proposed matching algorithm to get analogous
sounds alike (phonetic) pattern that is convenient for Myanmar
character spelling. According to the nature of Myanmar character, we
consider for word boundary fragmentation, collation of character.
Thus we use pattern conversion algorithm which fabricates words in
pattern with fragmented and collated. We create the Myanmar sounds
alike phonetic group to help in the phonetic matching. The
experimental results show that fragmentation accuracy in 99.32% and
processing time in 1.72 ms.
Abstract: There are many debates now regarding undervalued
and overvalued currencies currently traded on the world financial
market. This paper contributes to these debates from a theoretical
point of view. We present the three most commonly used methods of
estimating the equilibrium real effective exchange rate (REER):
macroeconomic balance approach, external sustainability approach
and equilibrium real effective exchange rate approach in the reduced
form. Moreover, we discuss key concepts of the calculation of the
real exchange rate (RER) based on applied explanatory variables:
nominal exchange rates, terms of trade and tradable and non-tradable
goods. Last but not least, we discuss the three main driving forces
behind real exchange rates movements which include terms of trade,
relative productivity growth and the interest rate differential.
Abstract: This paper presents a method for the optimal
allocation of Distributed generation in distribution systems. In this
paper, our aim would be optimal distributed generation allocation for
voltage profile improvement and loss reduction in distribution
network. Genetic Algorithm (GA) was used as the solving tool,
which referring two determined aim; the problem is defined and
objective function is introduced. Considering to fitness values
sensitivity in genetic algorithm process, there is needed to apply load
flow for decision-making. Load flow algorithm is combined
appropriately with GA, till access to acceptable results of this
operation. We used MATPOWER package for load flow algorithm
and composed it with our Genetic Algorithm. The suggested method
is programmed under MATLAB software and applied ETAP
software for evaluating of results correctness. It was implemented on
part of Tehran electricity distributing grid. The resulting operation of
this method on some testing system is illuminated improvement of
voltage profile and loss reduction indexes.