Abstract: Internet infrastructures in most places of the world
have been supported by the advancement of optical fiber technology,
most notably wavelength division multiplexing (WDM) system.
Optical technology by means of WDM system has revolutionized
long distance data transport and has resulted in high data capacity,
cost reductions, extremely low bit error rate, and operational
simplification of the overall Internet infrastructure. This paper
analyses and compares the system impairments, which occur at data
transmission rates of 2.5Gb/s and 10 Gb/s per wavelength channel in
our proposed optical WDM system for Internet infrastructure in
Tanzania. The results show that the data transmission rate of 2.5 Gb/s
has minimum system impairments compared with a rate of 10 Gb/s
per wavelength channel, and achieves a sufficient system
performance to provide a good Internet access service.
Abstract: In this study, control performance of a smart base
isolation system consisting of a friction pendulum system (FPS) and a
magnetorheological (MR) damper has been investigated. A fuzzy
logic controller (FLC) is used to modulate the MR damper so as to
minimize structural acceleration while maintaining acceptable base
displacement levels. To this end, a multi-objective optimization
scheme is used to optimize parameters of membership functions and
find appropriate fuzzy rules. To demonstrate effectiveness of the
proposed multi-objective genetic algorithm for FLC, a numerical
study of a smart base isolation system is conducted using several
historical earthquakes. It is shown that the proposed method can find
optimal fuzzy rules and that the optimized FLC outperforms not only a
passive control strategy but also a human-designed FLC and a
conventional semi-active control algorithm.
Abstract: In this work, we perform numerical simulation of fluid
mixing in a floor-grooved micro-channel with wavy sidewalls which
may impose perturbation on the helical flow induced by the slanted
grooves on the channel floor. The perturbation is caused by separation
vortices in the recesses of the wavy-walled channel as the Reynolds
number is large enough. The results show that the effects of the wavy
sidewalls of the present micromixer on the enhancement of fluid
mixing increase with the increase of Reynolds number. The degree of
mixing increases with the increase of the corrugation angle, until the
angle is greater than 45 degrees. Besides, the pumping pressure of the
micromixer increases with the increase of the corrugation angle
monotonically. Therefore, we would suggest setting the corrugation
angle of the wavy sidewalls to be 45 degrees.
Abstract: Electromyography (EMG) is the study of muscles function through analysis of electrical activity produced from muscles. This electrical activity which is displayed in the form of signal is the result of neuromuscular activation associated with muscle contraction. The most common techniques of EMG signal recording are by using surface and needle/wire electrode where the latter is usually used for interest in deep muscle. This paper will focus on surface electromyogram (SEMG) signal. During SEMG recording, several problems had to been countered such as noise, motion artifact and signal instability. Thus, various signal processing techniques had been implemented to produce a reliable signal for analysis. SEMG signal finds broad application particularly in biomedical field. It had been analyzed and studied for various interests such as neuromuscular disease, enhancement of muscular function and human-computer interface.
Abstract: The purpose of this study was to present a reliable mean for human-computer interfacing based on finger gestures made in two dimensions, which could be interpreted and adequately used in controlling a remote robot's movement. The gestures were captured and interpreted using an algorithm based on trigonometric functions, in calculating the angular displacement from one point of touch to another as the user-s finger moved within a time interval; thereby allowing for pattern spotting of the captured gesture. In this paper the design and implementation of such a gesture based user interface was presented, utilizing the aforementioned algorithm. These techniques were then used to control a remote mobile robot's movement. A resistive touch screen was selected as the gesture sensor, then utilizing a programmed microcontroller to interpret them respectively.
Abstract: This paper reports on the influence of surface-treated coarse recycled concrete aggregate (RCA) on developing the compressive strength of concrete. The coarse RCA was initially treated by separately impregnating it in calcium metasilicate (CM) or wollastonite and nanosilica (NS) prepared at various concentrations. The effects of both treatment materials on concrete properties (e.g., slump, density and compressive strength) were evaluated. Scanning electron microscopy (SEM) analysis was performed to examine the microstructure of the resulting concrete. Results show that the effective use of treated coarse RCA significantly enhances the compressive strength of concrete. This result is supported by the SEM analysis, which indicates the formation of a dense interface between the treated coarse RCA and the cement matrix. Coarse RCA impregnated in CM solution results in better concrete strength than NS, and the optimum concentration of CM solution recommended for treated coarse RCA is 10%.
Abstract: The demand for higher performance graphics
continues to grow because of the incessant desire towards realism.
And, rapid advances in fabrication technology have enabled us to
build several processor cores on a single die. Hence, it is important to
develop single chip parallel architectures for such data-intensive
applications. In this paper, we propose an efficient PIM architectures
tailored for computer graphics which requires a large number of
memory accesses. We then address the two important tasks necessary
for maximally exploiting the parallelism provided by the architecture,
namely, partitioning and placement of graphic data, which affect
respectively load balances and communication costs. Under the
constraints of uniform partitioning, we develop approaches for optimal
partitioning and placement, which significantly reduce search space.
We also present heuristics for identifying near-optimal placement,
since the search space for placement is impractically large despite our
optimization. We then demonstrate the effectiveness of our partitioning
and placement approaches via analysis of example scenes; simulation
results show considerable search space reductions, and our heuristics
for placement performs close to optimal – the average ratio of
communication overheads between our heuristics and the optimal was
1.05. Our uniform partitioning showed average load-balance ratio of
1.47 for geometry processing and 1.44 for rasterization, which is
reasonable.
Abstract: A cognitive collaborative reinforcement learning
algorithm (CCRL) that incorporates an advisor into the learning
process is developed to improve supervised learning. An autonomous
learner is enabled with a self awareness cognitive skill to decide
when to solicit instructions from the advisor. The learner can also
assess the value of advice, and accept or reject it. The method is
evaluated for robotic motion planning using simulation. Tests are
conducted for advisors with skill levels from expert to novice. The
CCRL algorithm and a combined method integrating its logic with
Clouse-s Introspection Approach, outperformed a base-line fully
autonomous learner, and demonstrated robust performance when
dealing with various advisor skill levels, learning to accept advice
received from an expert, while rejecting that of less skilled
collaborators. Although the CCRL algorithm is based on RL, it fits
other machine learning methods, since advisor-s actions are only
added to the outer layer.
Abstract: The implicit block methods based on the backward
differentiation formulae (BDF) for the solution of stiff initial value
problems (IVPs) using variable step size is derived. We construct a
variable step size block methods which will store all the coefficients
of the method with a simplified strategy in controlling the step size
with the intention of optimizing the performance in terms of
precision and computation time. The strategy involves constant,
halving or increasing the step size by 1.9 times the previous step size.
Decision of changing the step size is determined by the local
truncation error (LTE). Numerical results are provided to support the
enhancement of method applied.
Abstract: IEEE 802.11e is the enhanced version of the IEEE
802.11 MAC dedicated to provide Quality of Service of wireless
network. It supports QoS by the service differentiation and
prioritization mechanism. Data traffic receives different priority
based on QoS requirements. Fundamentally, applications are divided
into four Access Categories (AC). Each AC has its own buffer queue
and behaves as an independent backoff entity. Every frame with a
specific priority of data traffic is assigned to one of these access
categories. IEEE 802.11e EDCA (Enhanced Distributed Channel
Access) is designed to enhance the IEEE 802.11 DCF (Distributed
Coordination Function) mechanisms by providing a distributed
access method that can support service differentiation among
different classes of traffic. Performance of IEEE 802.11e MAC layer
with different ACs is evaluated to understand the actual benefits
deriving from the MAC enhancements.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.
Abstract: The research investigates the effects of super plasticizer and molarity of sodium hydroxide alkaline solution on the workability, microstructure and compressive strength of self compacting geopolymer concrete (SCGC). SCGC is an improved way of concreting execution that does not require compaction and is made by complete elimination of ordinary Portland cement content. The parameters studied were superplasticizer (SP) dosage and molarity of NaOH solution. SCGC were synthesized from low calcium fly ash, activated by combinations of sodium hydroxide and sodium silicate solutions, and by incorporation of superplasticizer for self compactability. The workability properties such as filling ability, passing ability and resistance to segregation were assessed using slump flow, T-50, V-funnel, L-Box and J-ring test methods. It was found that the essential workability requirements for self compactability according to EFNARC were satisfied. Results showed that the workability and compressive strength improved with the increase in superplasticizer dosage. An increase in strength and a decrease in workability of these concrete samples were observed with the increase in molarity of NaOH solution from 8M to 14M. Improvement of interfacial transition zone (ITZ) and micro structure with the increase of SP and increase of concentration from 8M to 12M were also identified.
Abstract: The steam cracking reactions are always accompanied with the formation of coke which deposits on the walls of the tubular reactors. The investigation has attempted to control catalytic coking by the applying aluminum, zinc and ceramic coating like aluminum-magnesium by thermal spray and pack cementation method. Rate of coke formation during steam cracking of naphtha has been investigated both for uncoated stainless steel (with different alloys) and metal coating constructed with thermal Spray and pack cementation method with metal powders of Aluminum, Aluminum-Magnesium, zinc, silicon, nickel and chromium. The results of the study show that passivating the surface of SS321 with a coating of Aluminum and Aluminum-Magnesium can significantly reduce the rate of coke deposition during naphtha pyrolysis. SEM and EDAX techniques (Philips XL Series) were used to examine the coke deposits formed by the metal-hydrocarbon reactions. Our objective was to separate the different stages by identifying the characteristic morphologies.
Abstract: Total liquid ventilation can support gas exchange in animal models of lung injury. Clinical application awaits further technical improvements and performance verification. Our aim was to develop a liquid ventilator, able to deliver accurate tidal volumes, and a computerized system for measuring lung mechanics. The computer-assisted, piston-driven respirator controlled ventilatory parameters that were displayed and modified on a real-time basis. Pressure and temperature transducers along with a lineal displacement controller provided the necessary signals to calculate lung mechanics. Ten newborn lambs (
Abstract: Software maintenance, which involves making enhancements, modifications and corrections to existing software systems, consumes more than half of developer time. Specification comprehensibility plays an important role in software maintenance as it permits the understanding of the system properties more easily and quickly. The use of formal notation such as B increases a specification-s precision and consistency. However, the notation is regarded as being difficult to comprehend. Semi-formal notation such as the Unified Modelling Language (UML) is perceived as more accessible but it lacks formality. Perhaps by combining both notations could produce a specification that is not only accurate and consistent but also accessible to users. This paper presents an experiment conducted on a model that integrates the use of both UML and B notations, namely UML-B, versus a B model alone. The objective of the experiment was to evaluate the comprehensibility of a UML-B model compared to a traditional B model. The measurement used in the experiment focused on the efficiency in performing the comprehension tasks. The experiment employed a cross-over design and was conducted on forty-one subjects, including undergraduate and masters students. The results show that the notation used in the UML-B model is more comprehensible than the B model.
Abstract: A complex valued neural network is a neural network, which consists of complex valued input and/or weights and/or thresholds and/or activation functions. Complex-valued neural networks have been widening the scope of applications not only in electronics and informatics, but also in social systems. One of the most important applications of the complex valued neural network is in image and vision processing. In Neural networks, radial basis functions are often used for interpolation in multidimensional space. A Radial Basis function is a function, which has built into it a distance criterion with respect to a centre. Radial basis functions have often been applied in the area of neural networks where they may be used as a replacement for the sigmoid hidden layer transfer characteristic in multi-layer perceptron. This paper aims to present exhaustive results of using RBF units in a complex-valued neural network model that uses the back-propagation algorithm (called 'Complex-BP') for learning. Our experiments results demonstrate the effectiveness of a Radial basis function in a complex valued neural network in image recognition over a real valued neural network. We have studied and stated various observations like effect of learning rates, ranges of the initial weights randomly selected, error functions used and number of iterations for the convergence of error on a neural network model with RBF units. Some inherent properties of this complex back propagation algorithm are also studied and discussed.
Abstract: It is important for an autonomous mobile robot to know
where it is in any time in an indoor environment. In this paper, we
design a relative self-localization algorithm. The algorithm compare
the interest point in two images and compute the relative displacement
and orientation to determent the posture. Firstly, we use the SURF
algorithm to extract the interest points of the ceiling. Second, in order
to reduce amount of calculation, a replacement SURF is used to extract
orientation and description of the interest points. At last, according to
the transformation of the interest points in two images, the relative
self-localization of the mobile robot will be estimated greatly.
Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.
Abstract: One of the most important parts of a cement factory is
the cement rotary kiln which plays a key role in quality and quantity of produced cement. In this part, the physical exertion and bilateral
movement of air and materials, together with chemical reactions take
place. Thus, this system has immensely complex and nonlinear dynamic equations. These equations have not worked out yet. Only
in exceptional case; however, a large number of the involved parameter were crossed out and an approximation model was
presented instead. This issue caused many problems for designing a
cement rotary kiln controller. In this paper, we presented nonlinear predictor and simulator models for a real cement rotary kiln by using
nonlinear identification technique on the Locally Linear Neuro-
Fuzzy (LLNF) model. For the first time, a simulator model as well as
a predictor one with a precise fifteen minute prediction horizon for a
cement rotary kiln is presented. These models are trained by
LOLIMOT algorithm which is an incremental tree-structure
algorithm. At the end, the characteristics of these models are expressed. Furthermore, we presented the pros and cons of these
models. The data collected from White Saveh Cement Company is used for modeling.
Abstract: Effect of high temperature exposure on properties of cement mortar containing municipal solid waste incineration (MSWI) bottom ash as partial natural aggregate replacement is analyzed in the paper. The measurements of mechanical properties, bulk density, matrix density, total open porosity, sorption and desorption isotherms are done on samples exposed to the temperatures of 20°C to 1000°C. TGA analysis is performed as well. Finally, the studied samples are analyzed by IR spectroscopy in order to evaluate TGA data.