Abstract: This paper presents the results of thermo-mechanical
characterization of Glass/Epoxy composite specimens using Infrared
Thermography technique. The specimens used for the study were
fabricated in-house with three different lay-up sequences and tested
on a servo hydraulic machine under uni-axial loading. Infrared
Camera was used for on-line monitoring surface temperature changes
of composite specimens during tensile deformation.
Experimental results showed that thermomechanical
characteristics of each type of specimens were distinct. Temperature
was found to be decreasing linearly with increasing tensile stress in
the elastic region due to thermo-elastic effect. Yield point could be
observed by monitoring the change in temperature profile during
tensile testing and this value could be correlated with the results
obtained from stress-strain response. The extent of prior plastic
deformation in the post-yield region influenced the slopes of
temperature response during tensile loading. Partial unloading and
reloading of specimens post-yield results in change in slope in elastic
and plastic regions of composite specimens.
Abstract: In this paper presents the mathematical model of
hydrothermal processes in thermal power plant with different wind
direction scenarios in the water reservoir, which is solved by the
Navier - Stokes and temperature equations for an incompressible
fluid in a stratified medium. Numerical algorithm based on the
method of splitting by physical parameters. Three dimensional
Poisson equation is solved with Fourier method by combination of
tridiagonal matrix method (Thomas algorithm).
Abstract: In electronegative-electropositive gas mixtures plasma, at a total pressure varying in the range of ten to hundred Torr, the appearance of a quasi-mochromatization effect of the emitted radiation was reported. This radiation could be the result of the generating mechanisms at molecular level, which is the case of the excimer radiation but also at atomic level. Thus, in the last case, in (Ne+1%Ar/Xe+H2) gas mixtures plasma in a dielectric barrier discharge, this effect, called M-effect, consists in the reduction of the discharge emission spectrum practice at one single, strong spectral line with λ = 585.3 nm. The present paper is concerned with the characteristics comparative investigation of the principal reaction mechanisms involved in the quasi-monochromatization effect existence in the case of the excimer radiation, respectively of the Meffect. Also, the paper points out the role of the metastable electronegative atoms in the appearance of the monochromatization – effect at atomic level.
Abstract: The flexible follower response of a translating cam with
four different profiles for rise-dwell-fall-dwell (RDFD) motion is
investigated. The cycloidal displacement motion, the modified
sinusoidal acceleration motion, the modified trapezoidal acceleration
motion, and the 3-4-5 polynomial motion are employed to describe the
rise and the fall motions of the follower and the associated four kinds of
cam profiles are studied. Since the follower flexibility is considered,
the contact point of the roller and the cam is an unknown. Two
geometric constraints formulated to restrain the unknown position are
substituted into Hamilton-s principle with Lagrange multipliers.
Applying the assumed mode method, one can obtain the governing
equations of motion as non-linear differential-algebraic equations. The
equations are solved using Runge-Kutta method. Then, the responses of
the flexible follower undergoing the four different motions are
investigated in time domain and in frequency domain.
Abstract: Having done in this study, air-conditioning
automation for patisserie shopwindow was designed. In the cooling
sector it is quite important to cooling up the air temperature in the
shopwindow within short time interval. Otherwise the patisseries
inside of the shopwindow will be spoilt in a few days. Additionally
the humidity is other important parameter for the patisseries kept in
shopwindow. It must be raised up to desired level in a quite short
time. Traditional patisserie shopwindows only allow controlling
temperature manually. There is no humidity control and humidity is
supplied by fans that are directed to the water at the bottom of the
shopwindows. In this study, humidity and temperature sensors
(SHT11), PIC, AC motor controller, DC motor controller, ultrasonic
nebulizer and other electronic circuit members were used to simulate
air conditioning automation for patisserie shopwindow in proteus
software package. The simulation results showed that temperature
and humidity values are adjusted in desired time duration by openloop
control technique. Outer and inner temperature and humidity
values were used for control mechanism.
Abstract: This paper presents a comparison of metaheuristic
algorithms, Genetic Algorithm (GA) and Ant Colony Optimization
(ACO), in producing freeman chain code (FCC). The main problem
in representing characters using FCC is the length of the FCC
depends on the starting points. Isolated characters, especially the
upper-case characters, usually have branches that make the traversing
process difficult. The study in FCC construction using one
continuous route has not been widely explored. This is our
motivation to use the population-based metaheuristics. The
experimental result shows that the route length using GA is better
than ACO, however, ACO is better in computation time than GA.
Abstract: In many applications, magnetic suspension systems
are required to operate over large variations in air gap. As a result,
the nonlinearities inherent in most types of suspensions have a
significant impact on performance. Specifically, it may be difficult to
design a linear controller which gives satisfactory performance,
stability, and disturbance rejection over a wide range of operating
points. in this paper an optimal controller based on discontinuous
mathematical model of the system for an electromagnetic suspension
system which is applied in magnetic trains has been designed .
Simulations show that the new controller can adapt well to the
variance of suspension mass and gap, and keep its dynamic
performance, thus it is superior to the classic controller.
Abstract: This paper discusses effects of adhesive thickness,
overlap length and material combinations on the single-lap
joints strength from the point of singular stress fields. A useful
method calculating the ratio of intensity of singular stress is
proposed using FEM for different adhesive thickness and
overlap length. It is found that the intensity of singular stress
increases with increasing adhesive thickness, and decreases
with increasing overlap length. The increment and decrement
are different depending on material combinations between
adhesive and adherent.
Abstract: Software security testing is an important means to ensure software security and trustiness. This paper first mainly discusses the definition and classification of software security testing, and investigates methods and tools of software security testing widely. Then it analyzes and concludes the advantages and disadvantages of various methods and the scope of application, presents a taxonomy of security testing tools. Finally, the paper points out future focus and development directions of software security testing technology.
Abstract: In this paper, a necessary and sufficient coefficient are given for functions in a class of complex valued meromorphic harmonic univalent functions of the form f = h + g using Salagean operator. Furthermore, distortion theorems, extreme points, convolution condition and convex combinations for this family of meromorphic harmonic functions are obtained.
Abstract: In Thailand, both the 1997 and the current 2007 Thai Constitutions have mentioned the establishment of independent organizations as a new mechanism to play a key role in proposing policy recommendations to national decision-makers in the interest of collective consumers. Over the last ten years, no independent organizations have yet been set up. Evidently, nobody could point out who should be key players in establishing provincial independent consumer bodies. The purpose of this study was to find definitive stakeholders in establishing and developing independent consumer bodies in a Thai context. This was a cross-sectional study between August and September 2007, using a postal questionnaire with telephone follow-up. The questionnaire was designed and used to obtain multiple stakeholder assessment of three key attributes (power, interest and influence). Study population was 153 stakeholders associated with policy decision-making, formulation and implementation processes of civil-based consumer protection in pilot provinces. The population covered key representatives from five sectors (academics, government officers, business traders, mass media and consumer networks) who participated in the deliberative forums at 10 provinces. A 49.7% response rate was achieved. Data were analyzed, comparing means of three stakeholder attributes and classification of stakeholder typology. The results showed that the provincial health officers were the definitive stakeholders as they had legal power, influence and interest in establishing and sustaining the independent consumer bodies. However, only a few key representatives of the provincial health officers expressed their own paradigm on the civil-based consumer protection. Most provincial health officers put their own standpoint of building civic participation at only a plan-implementation level. For effective policy implementation by the independent consumer bodies, the Thai government should provide budgetary support for the operation of the provincial health officers with their paradigm shift as well as their own clarified standpoint on corporate governance.
Abstract: Software project effort estimation is frequently seen
as complex and expensive for individual software engineers.
Software production is in a crisis. It suffers from excessive costs.
Software production is often out of control. It has been suggested that
software production is out of control because we do not measure.
You cannot control what you cannot measure. During last decade, a
number of researches on cost estimation have been conducted. The
metric-set selection has a vital role in software cost estimation
studies; its importance has been ignored especially in neural network
based studies. In this study we have explored the reasons of those
disappointing results and implemented different neural network
models using augmented new metrics. The results obtained are
compared with previous studies using traditional metrics. To be able
to make comparisons, two types of data have been used. The first
part of the data is taken from the Constructive Cost Model
(COCOMO'81) which is commonly used in previous studies and the
second part is collected according to new metrics in a leading
international company in Turkey. The accuracy of the selected
metrics and the data samples are verified using statistical techniques.
The model presented here is based on Multi-Layer Perceptron
(MLP). Another difficulty associated with the cost estimation studies
is the fact that the data collection requires time and care. To make a
more thorough use of the samples collected, k-fold, cross validation
method is also implemented. It is concluded that, as long as an
accurate and quantifiable set of metrics are defined and measured
correctly, neural networks can be applied in software cost estimation
studies with success
Abstract: There are various overlay structures that provide
efficient and scalable solutions for point and range query in a peer-topeer
network. Overlay structure based on m-Binary Search Tree
(BST) is one such popular technique. It deals with the division of the
tree into different key intervals and then assigning the key intervals to
a BST. The popularity of the BST makes this overlay structure
vulnerable to different kinds of attacks. Here we present four such
possible attacks namely index poisoning attack, eclipse attack,
pollution attack and syn flooding attack. The functionality of BST is
affected by these attacks. We also provide different security
techniques that can be applied against these attacks.
Abstract: University websites are considered as one of the brand primary touch points for multiple stakeholders, but most of them did not have great designs to create favorable impressions. Some of the elements that web designers should carefully consider are the appearance, the content, the functionality, usability and search engine optimization. However, priority should be placed on website simplicity and negative space. In terms of content, previous research suggests that universities should include reputation, learning environment, graduate career prospects, image destination, cultural integration, and virtual tour on their websites. The study examines how top 200 world ranking science and technology-based universities present their brands online and whether the websites capture the content dimensions. Content analysis of the websites revealed that the top ranking universities captured these dimensions at varying degree. Besides, the UK-based university had better priority on website simplicity and negative space compared to the Malaysian-based university.
Abstract: The stereophotogrammetry modality is gaining more widespread use in the clinical setting. Registration and visualization of this data, in conjunction with conventional 3D volumetric image modalities, provides virtual human data with textured soft tissue and internal anatomical and structural information. In this investigation computed tomography (CT) and stereophotogrammetry data is acquired from 4 anatomical phantoms and registered using the trimmed iterative closest point (TrICP) algorithm. This paper fully addresses the issue of imaging artifacts around the stereophotogrammetry surface edge using the registered CT data as a reference. Several iterative algorithms are implemented to automatically identify and remove stereophotogrammetry surface edge outliers, improving the overall visualization of the combined stereophotogrammetry and CT data. This paper shows that outliers at the surface edge of stereophotogrammetry data can be successfully removed automatically.
Abstract: This paper proposes a solution to the motion planning
and control problem of a point-mass robot which is required to move
safely to a designated target in a priori known workspace cluttered
with fixed elliptical obstacles of arbitrary position and sizes. A
tailored and unique algorithm for target convergence and obstacle
avoidance is proposed that will work for any number of fixed
obstacles. The control laws proposed in this paper also ensures that
the equilibrium point of the given system is asymptotically stable.
Computer simulations with the proposed technique and applications
to a planar (RP) manipulator will be presented.
Abstract: The purpose of the study was to investigate the
effectiveness of ICT training workshop of tutors of Allama Iqbal
Open University Pakistan. The study was delimited to tutors of
Multan region. The total sample comprised of 100 tutors. All the
tutors who participated in ICT training workshop in Multan region
were taken as sample in the study. A questionnaire having two parts,
based on five point rating scale was developed by the researcher. Part
one was about the competency level of computer skills while Part
two was based on items related to training delivery, structure and
content. Part One of questionnaire had five levels of competency
about computer skills. The questionnaire was personally administered
and collected back by the researcher himself on the last day of
workshop.
The collected data were analyzed by using descriptive statistics.
Through this study it was found that majority of the tutors strongly
agreed that training enhanced their computer skills. Majority of the
respondents consider themselves to be generally competent in the use
of computer. They also agreed that there was appropriate
infrastructure and technical support in lab during training workshop.
Moreover, it was found that the training imparted the knowledge of
pedagogy of using computers for distance education.
Abstract: In this paper, a Bayesian Network (BN) based system
is presented for providing clinical decision support to healthcare
practitioners in rural or remote areas of India for young infants or
children up to the age of 5 years. The government is unable to
appoint child specialists in rural areas because of inadequate number
of available pediatricians. It leads to a high Infant Mortality Rate
(IMR). In such a scenario, Intelligent Pediatric System provides a
realistic solution. The prototype of an intelligent system has been
developed that involves a knowledge component called an Intelligent
Pediatric Assistant (IPA); and User Agents (UA) along with their
Graphical User Interfaces (GUI). The GUI of UA provides the
interface to the healthcare practitioner for submitting sign-symptoms
and displaying the expert opinion as suggested by IPA. Depending
upon the observations, the IPA decides the diagnosis and the
treatment plan. The UA and IPA form client-server architecture for
knowledge sharing.
Abstract: Natural convection heat transfer from a heated
horizontal semi-circular cylinder (flat surface upward) has been
investigated for the following ranges of conditions; Grashof number,
and Prandtl number. The governing partial differential equations
(continuity, Navier-Stokes and energy equations) have been solved
numerically using a finite volume formulation. In addition, the role of
the type of the thermal boundary condition imposed at cylinder
surface, namely, constant wall temperature (CWT) and constant heat
flux (CHF) are explored. Natural convection heat transfer from a
heated horizontal semi-circular cylinder (flat surface upward) has
been investigated for the following ranges of conditions; Grashof
number, and Prandtl number, . The governing partial differential
equations (continuity, Navier-Stokes and energy equations) have
been solved numerically using a finite volume formulation. In
addition, the role of the type of the thermal boundary condition
imposed at cylinder surface, namely, constant wall temperature
(CWT) and constant heat flux (CHF) are explored. The resulting flow
and temperature fields are visualized in terms of the streamline and
isotherm patterns in the proximity of the cylinder. The flow remains
attached to the cylinder surface over the range of conditions spanned
here except that for and ; at these conditions, a separated flow
region is observed when the condition of the constant wall
temperature is prescribed on the surface of the cylinder. The heat
transfer characteristics are analyzed in terms of the local and average
Nusselt numbers. The maximum value of the local Nusselt number
always occurs at the corner points whereas it is found to be minimum
at the rear stagnation point on the flat surface. Overall, the average
Nusselt number increases with Grashof number and/ or Prandtl
number in accordance with the scaling considerations. The numerical
results are used to develop simple correlations as functions of
Grashof and Prandtl number thereby enabling the interpolation of the
present numerical results for the intermediate values of the Prandtl or
Grashof numbers for both thermal boundary conditions.
Abstract: In this research a mathematical model for direct
oxidization of hydrogen sulfide into elemental sulfur in a fluidized
bed reactor with external circulation was developed. As the catalyst
is deactivated in the fluidized bed, it might be placed in a reduction
tank in order to remove sulfur through heating above its dew point.
The reactor model demonstrated via MATLAB software. It was
shown that variations of H2S conversion as well as; products formed
were reasonable in comparison with corresponding results of a fixed
bed reactor. Through analyzing results of this model, it became
possible to propose the main optimized operating conditions for the
process considered. These conditions included; the temperature range
of 100-130ºC and utilizing the catalyst as much as possible providing
the highest bed density respect to dimensions of bed, economical
aspects that the bed ever remained in fluidized mode. A high active
and stable catalyst under the optimum conditions exhibited 100%
conversion in a fluidized bed reactor.