Abstract: In the past many uneconomic solutions for limitation
and interruption of short-circuit currents in low power applications
have been introduced, especially polymer switch based on the
positive temperature coefficient of resistance (PCTR) concept.
However there are many limitations in the active material, which
consists of conductive fillers. This paper presents a significantly
improved and simplified approach that replaces the existing current
limiters with faster switching elements. Its elegance lies in the
remarkable simplicity and low-cost processes of producing the device
using polyaniline (PANI) doped with methane-sulfonic acid (MSA).
Samples characterized as lying in the metallic and critical regimes of
metal insulator transition have been studied by means of electrical
performance in the voltage range from 1V to 5 V under different
environmental conditions. Moisture presence is shown to increase the
resistivity and also improved its current limiting performance.
Additionally, the device has also been studied for electrical resistivity
in the temperature range 77 K-300 K. The temperature dependence of
the electrical conductivity gives evidence for a transport mechanism
based on variable range hopping in three dimensions.
Abstract: This paper applies fuzzy AHP to evaluate the service
quality of online auction. Service quality is a composition of various
criteria. Among them many intangible attributes are difficult to
measure. This characteristic introduces the obstacles for respondents
on reply in the survey. So as to overcome this problem, we invite
fuzzy set theory into the measurement of performance and use AHP in
obtaining criteria. We found the most concerned dimension of service
quality is Transaction Safety Mechanism and the least is Charge Item.
Other criteria such as information security, accuracy and information
are too vital.
Abstract: In recent years, the use of vector variance as a
measure of multivariate variability has received much attention in
wide range of statistics. This paper deals with a more economic
measure of multivariate variability, defined as vector variance minus
all duplication elements. For high dimensional data, this will increase
the computational efficiency almost 50 % compared to the original
vector variance. Its sampling distribution will be investigated to make
its applications possible.
Abstract: Modular multiplication is the basic operation
in most public key cryptosystems, such as RSA, DSA, ECC,
and DH key exchange. Unfortunately, very large operands
(in order of 1024 or 2048 bits) must be used to provide
sufficient security strength. The use of such big numbers
dramatically slows down the whole cipher system, especially
when running on embedded processors.
So far, customized hardware accelerators - developed on
FPGAs or ASICs - were the best choice for accelerating
modular multiplication in embedded environments. On the
other hand, many algorithms have been developed to speed
up such operations. Examples are the Montgomery modular
multiplication and the interleaved modular multiplication
algorithms. Combining both customized hardware with
an efficient algorithm is expected to provide a much faster
cipher system.
This paper introduces an enhanced architecture for computing
the modular multiplication of two large numbers X
and Y modulo a given modulus M. The proposed design is
compared with three previous architectures depending on
carry save adders and look up tables. Look up tables should
be loaded with a set of pre-computed values. Our proposed
architecture uses the same carry save addition, but replaces
both look up tables and pre-computations with an enhanced
version of sign detection techniques. The proposed architecture
supports higher frequencies than other architectures.
It also has a better overall absolute time for a single operation.
Abstract: This research details a Computational Fluid Dynamics (CFD) approach to model fluid flow in a journal bearing with 8 equispaced semi-circular axial grooves. Water is used as the lubricant and is fed from one end of the bearing to the other, under pressure. The geometry of the bearing is modeled using a commercially available modeling software GAMBIT and the flow analysis is performed using a dedicated CFD analysis software FLUENT. The pressure distribution in the bearing clearance is obtained from FLUENT for various whirl ratios and is used to calculate the hydrodynamic force components in the radial and tangential direction of the bearing. These values along with the various whirl speeds can be used to do a regression analysis to determine the stiffness and damping coefficients. The values obtained are then compared with the stiffness and damping coefficients of a 3 Axial groove water lubricated journal bearing and those obtained from a FORTRAN code for a similar bearing.
Abstract: In this paper the concept of Q-fuzzification of ideals of Γ-semigroups has been introduced and some important properties have been investigated. A characterization of regular Γ-semigroup in terms of Q-fuzzy ideals has been obtained. Operator semigroups of a Γ-semigroup has been made to work by obtaining various relationships between Q-fuzzy ideals of a Γ-semigroup and that of its operator semigroups.
Abstract: The utility of expert system generators has been
widely recognized in many applications. Several generators based on
concept of the paradigm object, have been recently proposed. The
generator of oriented object expert system (GSEOO) offers
languages that are often complex and difficult to use. We propose in
this paper an extension of the expert system generator, JESS, which
permits a friendly use of this expert system. The new tool, called
VISUAL JESS, bring two main improvements to JESS. The first
improvement concerns the easiness of its utilization while giving
back transparency to the syntax and semantic aspects of the JESS
programming language. The second improvement permits an easy
access and modification of the JESS knowledge basis. The
implementation of VISUAL JESS is made so that it is extensible and
portable.
Abstract: The purpose of this study is mainly to predict collision
frequency on the horizontal tangents combined with vertical curves
using artificial neural network methods. The proposed ANN models
are compared with existing regression models. First, the variables
that affect collision frequency were investigated. It was found that
only the annual average daily traffic, section length, access density,
the rate of vertical curvature, smaller curve radius before and after
the tangent were statistically significant according to related
combinations. Second, three statistical models (negative binomial,
zero inflated Poisson and zero inflated negative binomial) were
developed using the significant variables for three alignment
combinations. Third, ANN models are developed by applying the
same variables for each combination. The results clearly show that
the ANN models have the lowest mean square error value than those
of the statistical models. Similarly, the AIC values of the ANN
models are smaller to those of the regression models for all the
combinations. Consequently, the ANN models have better statistical
performances than statistical models for estimating collision
frequency. The ANN models presented in this paper are
recommended for evaluating the safety impacts 3D alignment
elements on horizontal tangents.
Abstract: Most of the commercial gluten free products are
nutritionally inferior when compared to gluten containing
counterparts as manufacturers most often use the refined flours and
starches. So it is possible that people on gluten free diet have low
intake of fibre content. The foxtail millet flour and copra meal are
gluten free and have high fibre and protein contents. The formulation
of fibre rich gluten free cookies was optimized by response surface
methodology considering independent process variables as proportion
of Foxtail millet (Setaria italica) flour in mixed flour, fat content and
guar gum. The sugar, sodium chloride, sodium bicarbonates and
water were added in fixed proportion as 60, 1.0, 0.4 and 20% of
mixed flour weight, respectively. Optimum formulation obtained for
maximum spread ratio, fibre content, surface L-value, overall
acceptability and minimum breaking strength were 80% foxtail millet
flour in mixed flour, 42.8 % fat content and 0.05% guar gum.
Abstract: Series compensators have been used for many years,
to increase the stability and load ability of transmission line. They
compensate retarded or advanced volt drop of transmission lines
by placing advanced or retarded voltage in series with them to
compensate the effective reactance, which cause to increase load
ability of transmission lines. In this paper, two method of fuzzy
controller, based on power reference tracking and impedance
reference tracking have been developed on TCSC controller in
order to increase load ability and improving power oscillation
damping of system. In these methods, fire angle of thyristors are
determined directly through the special Rule-bases with the error
and change of error as the inputs. The simulation results of two
area four- machines power system show the good performance of
power oscillation damping in system. Comparison of this method
with classical PI controller shows the increasing speed of system
response in power oscillation damping.
Abstract: Component handling system is one of the important sub systems of Prototype Fast Breeder Reactor (PFBR) used for fuel handling. Core handling system is again a sub system of component handling system. Core handling system consists of in-vessel and ex-vessel subassembly handling. In-vessel core handling involves transfer arm, large rotatable plug and small rotatable plug operations. Modeling and simulation of in-vessel core handling is a part of development of Prototype Fast Breeder Reactor Operator Training Simulator. This paper deals with simulation and modeling of operations of transfer arm, large rotatable plug and small rotatable plug needed for in-vessel core handling. Process modeling was developed in house using platform independent Cµ code with OpenGL (Open Graphics Library). The control logic models and virtual panel were modeled using simulation tool.
Abstract: 4G Communication Networks provide heterogeneous
wireless technologies to mobile subscribers through IP based
networks and users can avail high speed access while roaming across
multiple wireless channels; possible by an organized way to manage
the Quality of Service (QoS) functionalities in these networks. This
paper proposes the idea of developing a novel QoS optimization
architecture that will judge the user requirements and knowing peak
times of services utilization can save the bandwidth/cost factors. The
proposed architecture can be customized according to the network
usage priorities so as to considerably improve a network-s QoS
performance.
Abstract: Herein, the organic semiconductor methyl orange
(MO), is investigated for the first time for its electronic applications.
For this purpose, Al/MO/n-Si heterojunction is fabricated through
economical cheap and simple “drop casting” technique. The currentvoltage
(I-V) measurements of the device are made at room
temperature under dark conditions. The I-V characteristics of
Al/MO/n-Si junction exhibits asymmetrical and rectifying behavior
that confirms the formation of diode. The diode parameters such as
rectification ratio (RR), turn on voltage (Vturn on), reverse saturation
current (I0), ideality factor (n), barrier height ( b
f ), series resistance
(Rs) and shunt resistance (Rsh) are determined from I-V curves using
Schottky equations. These values of these parameters are also
extracted and verified by applying Cheung’s functions. The
conduction mechanisms are explained from the forward bias I-V
characteristics using the power law.
Abstract: The notion of k-fuzzy ideals of semirings was introduced
by Kim and Park in 1996. In 2003, Dutta and Kar introduced
a notion of ternary semirings. This structure is a generalization of
ternary rings and semirings. The main purpose of this paper is to
introduce and study k-fuzzy ideals in ternary semirings analogous to
k-fuzzy ideals in semirings considered by Kim and Park.
Abstract: The purpose of this paper is to demonstrate the ability
of a genetic programming (GP) algorithm to evolve a team of data
classification models. The GP algorithm used in this work is
“multigene" in nature, i.e. there are multiple tree structures (genes)
that are used to represent team members. Each team member assigns
a data sample to one of a fixed set of output classes. A majority vote,
determined using the mode (highest occurrence) of classes predicted
by the individual genes, is used to determine the final class
prediction. The algorithm is tested on a binary classification problem.
For the case study investigated, compact classification models are
obtained with comparable accuracy to alternative approaches.
Abstract: This paper investigates the development of weld zone
in Resistance Spot Welding (RSW) which focuses on weld nugget and Heat Affected Zone (HAZ). The effects of four factors namely
weld current, weld time, electrode force and hold time were studied using a general 24 factorial design augmented by five centre points. The results of the analysis showed that all selected factors except
hold time exhibit significant effect on weld nugget radius and HAZ size. Optimization of the welding parameters (weld current, weld
time and electrode force) to normalize weld nugget and to minimize
HAZ size was then conducted using Central Composite Design (CCD) in Response Surface Methodology (RSM) and the optimum
parameters were determined. A regression model for radius of weld nugget and HAZ size was developed and its adequacy was evaluated.
The experimental results obtained under optimum operating conditions were then compared with the predicted values and were
found to agree satisfactorily with each other
Abstract: A real time distributed computing has
heterogeneously networked computers to solve a single problem. So
coordination of activities among computers is a complex task and
deadlines make more complex. The performances depend on many
factors such as traffic workloads, database system architecture,
underlying processors, disks speeds, etc. Simulation study have been
performed to analyze the performance under different transaction
scheduling: different workloads, arrival rate, priority policies,
altering slack factors and Preemptive Policy. The performance metric
of the experiments is missed percent that is the percentage of
transaction that the system is unable to complete. The throughput of
the system is depends on the arrival rate of transaction. The
performance can be enhanced with altering the slack factor value.
Working on slack value for the transaction can helps to avoid some
of transactions from killing or aborts. Under the Preemptive Policy,
many extra executions of new transactions can be carried out.
Abstract: The non-destructive testing of launch tube weld with
radiography was investigated and evaluated with AWS D1.1
standard. The paper started with preparation of launch tube and
radiographic inspection. X-Ray inspection then was done and gotten
the result. The judgment of inspection results were concluded by
certified person and finally, the evaluation with AWS D1.1 standard
was conducted as well.
The result shown that weld position P1 was not conformed to
AWS D1.1 which allowed size of incomplete penetration did not
exceed 4 mm. The other welds were corresponded to as mentioned
standard. Additionally, the corrective actions for incomplete
penetration either provided for future actions.
Abstract: The aim of the work was to attenuate the vibration amplitude in CESNA 172 airplane wing by using Functionally Graded Material instead of uniform or composite material. Wing strength was achieved by means of stress analysis study, while wing vibration amplitudes and shapes were achieved by means of Modal and Harmonic analysis. Results were verified by applying the methodology in a simple cantilever plate to the simple model and the results were promising and the same methodology can be applied to the airplane wing model. Aluminum models, Titanium models, and functionally graded materials of Aluminum and titanium results were compared to show a great vibration attenuation after using the FGM. Optimization in FGM gradation satisfied our objective of reducing and attenuating the vibration amplitudes to show the effect of using FGM in vibration behavior. Testing the Aluminum rich models, and comparing it with the titanium rich model was an optimization in this paper. Results have shown a significant attenuation in vibration magnitudes when using FGM instead of Titanium Plate, and Aluminium wing with FGM Spurs instead of Aluminium wings. It was also recommended that in future, changing the graphical scale to 1:10 or even 1:1 when the computers- capabilities allow.
Abstract: Business rules are widely used within the services
sector. They provide consistency and allow relatively unskilled staff
to process complex transactions correctly. But there are many
examples where the rules themselves have an impact on the costs and
profits of an organisation. Financial services, transport and human
services are areas where the rules themselves can impact the bottom
line in a predictable way. If this is the case, how can we find that set
of rules that maximise profit, performance or customer service, or
any other key performance indicators? The manufacturing, energy
and process industries have embraced mathematical optimisation
techniques to improve efficiency, increase production and so on. This
paper explores several real world (but simplified) problems in the
services sector and shows how business rules can be optimised. It
also examines the similarities and differences between the service
and other sectors, and how optimisation techniques could be used to
deliver similar benefits.