Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.
Abstract: Scripts are one of the basic text resources to understand
broadcasting contents. Topic modeling is the method to get the
summary of the broadcasting contents from its scripts. Generally,
scripts represent contents descriptively with directions and speeches,
and provide scene segments that can be seen as semantic units.
Therefore, a script can be topic modeled by treating a scene segment
as a document. Because scene segments consist of speeches mainly,
however, relatively small co-occurrences among words in the scene
segments are observed. This causes inevitably the bad quality of
topics by statistical learning method. To tackle this problem, we
propose a method to improve topic quality with additional word
co-occurrence information obtained using scene similarities. The
main idea of improving topic quality is that the information that
two or more texts are topically related can be useful to learn high
quality of topics. In addition, more accurate topical representations
lead to get information more accurate whether two texts are related
or not. In this paper, we regard two scene segments are related
if their topical similarity is high enough. We also consider that
words are co-occurred if they are in topically related scene segments
together. By iteratively inferring topics and determining semantically
neighborhood scene segments, we draw a topic space represents
broadcasting contents well. In the experiments, we showed the
proposed method generates a higher quality of topics from Korean
drama scripts than the baselines.
Abstract: The early-stage damage detection in offshore
structures requires continuous structural health monitoring and for the
large area the position of sensors will also plays an important role in
the efficient damage detection. Determining the dynamic behavior of
offshore structures requires dense deployment of sensors. The wired
Structural Health Monitoring (SHM) systems are highly expensive
and always needs larger installation space to deploy. Wireless sensor
networks can enhance the SHM system by deployment of scalable
sensor network, which consumes lesser space. This paper presents the
results of wireless sensor network based Structural Health Monitoring
method applied to a scaled experimental model of offshore structure
that underwent wave loading. This method determines the
serviceability of the offshore structure which is subjected to various
environment loads. Wired and wireless sensors were installed in the
model and the response of the scaled BLSRP model under wave
loading was recorded. The wireless system discussed in this study is
the Raspberry pi board with Arm V6 processor which is programmed
to transmit the data acquired by the sensor to the server using Wi-Fi
adapter, the data is then hosted in the webpage. The data acquired
from the wireless and wired SHM systems were compared and the
design of the wireless system is verified.
Abstract: Multiple Sclerosis (MS) is a disease which affects the
central nervous system and causes balance problem. In clinical, this
disorder is usually evaluated using static posturography. Some linear
or nonlinear measures, extracted from the posturographic data (i.e.
center of pressure, COP) recorded during a balance test, has been
used to analyze postural control of MS patients. In this study, the
trend (TREND) and the sample entropy (SampEn), two nonlinear
parameters were chosen to investigate their relationships with the
expanded disability status scale (EDSS) score. 40 volunteers with
different EDSS scores participated in our experiments with eyes open
(EO) and closed (EC). TREND and 2 types of SampEn (SampEn1
and SampEn2) were calculated for each combined COP’s position
signal. The results have shown that TREND had a weak negative
correlation to EDSS while SampEn2 had a strong positive correlation
to EDSS. Compared to TREND and SampEn1, SampEn2 showed a
better significant correlation to EDSS and an ability to discriminate
the MS patients in the EC case. In addition, the outcome of the study
suggests that the multi-dimensional nonlinear analysis could provide
some information about the impact of disability progression in MS on
dynamics of the COP data.
Abstract: This paper presents the experimental results of 11 kV
and 33 kV silicon composite insulators under artificial salt and urea
polluted conditions. The tests were carried out under different
seasons like summer, winter, and monsoon. The artificial pollution is
prepared by properly dissolving the salt and urea in the water. The
prepared salt and urea pollutions are sprayed on the insulators and
dried up for sufficiently large time. The process is continued until a
uniform layer is formed on the surface of insulator. For each insulator
rating, four samples were tested. The maximum leakage current and
breakdown voltage were measured. From experimental data,
performance of test specimen is evaluated by comparing breakdown
voltage and leakage current during different seasons when exposed to
salt and urea polluted conditions. From these results the performance
of the insulators can be predicted when they are installed in
industrial, agricultural, and coastal areas. The experimental tests were
carried out in the High Voltage laboratory using two stage cascade
transformer having the rating of 1000 kVA, 500 kV.
Abstract: The study assessed the effectiveness of Pawpaw
(Carica papaya) wood in reducing the concentrations of heavy
metals in wastewater acting as a bio-sorbent. The following heavy
metals were considered; Zinc, Cadmium, Lead, Copper, Iron,
Selenium, Nickel and Manganese. The physiochemical properties of
Carica papaya stem were studied. The experimental sample was
sourced from the trunk of a felled matured pawpaw tree. Wastewater
for experimental use was prepared by dissolving soil samples
collected from a dump site at Owerri, Imo state of Nigeria in water.
The concentration of each metal remaining in solution as residual
metal after bio-sorption was determined using Atomic absorption
Spectrometer. The effects of pH and initial heavy metal concentration
were studied in a batch reactor. The results of Spectrometer test
showed that there were different functional groups detected in the
Carica papaya stem biomass. There was increase in metal removal as
the pH increased for all the metals considered except for Nickel and
Manganese. Optimum bio-sorption occurred at pH 5.9 with 5g/100ml
solution of bio-sorbent. The results of the study showed that the
treated wastewater is fit for irrigation purpose based on Canada
wastewater quality guideline for the protection of Agricultural
standard. This approach thus provides a cost effective and
environmentally friendly option for treating wastewater.
Abstract: Fermentation is well known as an essential process to
develop chocolate flavor in dried cocoa beans. Besides developing
the precursor of cocoa flavor, it also induces the color changes in the
beans. The fermentation process is influenced by various factors such
as planting material, preconditioning of cocoa pod and fermentation
technique. Therefore, this study was conducted to evaluate color of
Malaysian cocoa beans and how the duration of pods storage and
fermentation technique using shallow box will effect on its color
characteristics. There are two factors being studied i.e. duration of
cocoa pod storage (0, 2, 4 and 6 days) and duration of cocoa
fermentation (0, 1, 2, 3, 4 and 5 days). The experiment is arranged in
4 x 6 factorial designs with 24 treatments and arrangement is in a
Completely Randomised Design (CRD). The produced beans are
inspected for color changes under artificial light during cut test and
divided into four groups of color namely fully brown, purple brown,
fully purple and slaty. Cut tests indicated that cocoa beans which are
directly dried without undergone fermentation has the highest slaty
percentage. However, application of pods storage before fermentation
process is found to decrease the slaty percentage. In contrast, the
percentages of fully brown beans start to dominate after two days of
fermentation, especially from four and six days of pods storage batch.
Whereas, almost all batches of cocoa beans have a percentage of fully
purple less than 20%. Interestingly, the percentage of purple brown
beans are scattered in the entire beans batch regardless any specific
trend. Meanwhile, statistical analysis using General Linear Model
showed that the pods storage has a significant effect on the color
characteristic of the Malaysian dried beans compared to fermentation
duration.
Abstract: Earth structures constructed of marine clay soils have
tendency to crack. In order to improve the flexural strength and
brittleness, a technique of mixing short fibers is introduced to the soil
lime mixture. Coir fiber was used in this study as reinforcing
elements. An experimental investigation consisting primarily of
flexural tensile tests was conducted to examine the influence of coir
fibers on the flexural behaviour of the reinforced soils. The test
results that the coir fibers were effective in improving the flexural
strength and Young’s modulus of all soils examined and ductility
after peak strength for reinforced marine clay soil treated by lime. 5%
lime treated soil and 1% coir fiber reinforced soil specimens’
demonstrated good strength and durability when submerged in water
and retained 45% of their air-cured strengths.
Abstract: In this paper, an approach for the liver tumor detection
in computed tomography (CT) images is represented. The detection
process is based on classifying the features of target liver cell to
either tumor or non-tumor. Fractional differential (FD) is applied for
enhancement of Liver CT images, with the aim of enhancing texture
and edge features. Later on, a fusion method is applied to merge
between the various enhanced images and produce a variety of
feature improvement, which will increase the accuracy of
classification. Each image is divided into NxN non-overlapping
blocks, to extract the desired features. Support vector machines
(SVM) classifier is trained later on a supplied dataset different from
the tested one. Finally, the block cells are identified whether they are
classified as tumor or not. Our approach is validated on a group of
patients’ CT liver tumor datasets. The experiment results
demonstrated the efficiency of detection in the proposed technique.
Abstract: This paper aims to analysis the behavior of DC corona
discharge in wire-to-plate electrostatic precipitators (ESP). Currentvoltage
curves are particularly analyzed. Experimental results show
that discharge current is strongly affected by the applied voltage. The proposed method of current identification is to use the method
of least squares. Least squares problems that of into two categories:
linear or ordinary least squares and non-linear least squares,
depending on whether or not the residuals are linear in all unknowns.
The linear least-squares problem occurs in statistical regression
analysis; it has a closed-form solution. A closed-form solution (or
closed form expression) is any formula that can be evaluated in a
finite number of standard operations. The non-linear problem has no
closed-form solution and is usually solved by iterative.
Abstract: There was a scenario present day that drying of fresh
fruits and vegetables by indirect solar drying by using mechanical
device; hence, an effort was made to develop a small scale solar
tunnel dryer (STD). Drying of spinach is carried out to analyze the
performance of the dryer and to study its drying characteristics. To
evaluate the performance of dryer the independent variables were
selected as air flow rate, loading density and shade net while collector
efficiency, drying efficiency, overall efficiency and specific energy
consumption were selected as responses during performing the
experiments. The spinach was dried from initial moisture content
88.21-94.04% (w.b.) to final moisture content 3.50-5.13% (w.b.). The
drying time considerably reduced as compared to open sun drying of
spinach as sun drying took 15 h for drying. The average collector
efficiency, drying efficiency and overall efficiency were in the range
28.73-61.15%, 11.63% to 22.13%, and 7.61-14.66%, respectively.
Abstract: With the advancement of knowledge about the utility
and impact of sustainability, its feasibility has been explored into
different walks of life. Scientists, however; have established their
knowledge in four areas viz environmental, economic, social and
cultural, popularly termed as four pillars of sustainability. Aspects of
environmental and economic sustainability have been rigorously
researched and practiced and huge volume of strong evidence of
effectiveness has been founded for these two sub-areas. For the social
and cultural aspects of sustainability, dependable evidence of
effectiveness is still to be instituted as the researchers and
practitioners are developing and experimenting methods across the
globe. Therefore, the present research aimed to identify globally used
practices of social and cultural sustainability and through evidence
synthesis assess their outcomes to determine the effectiveness of
those practices. A PICO format steered the methodology which
included all populations, popular sustainability practices including
walkability/cycle tracks, social/recreational spaces, privacy, health &
human services and barrier free built environment, comparators
included ‘Before’ and ‘After’, ‘With’ and ‘Without’, ‘More’ and
‘Less’ and outcomes included Social well-being, cultural coexistence,
quality of life, ethics and morality, social capital, sense of
place, education, health, recreation and leisure, and holistic
development. Search of literature included major electronic
databases, search websites, organizational resources, directory of
open access journals and subscribed journals. Grey literature,
however, was not included. Inclusion criteria filtered studies on the
basis of research designs such as total randomization, quasirandomization,
cluster randomization, observational or single studies
and certain types of analysis. Studies with combined outcomes were
considered but studies focusing only on environmental and/or
economic outcomes were rejected. Data extraction, critical appraisal
and evidence synthesis was carried out using customized tabulation,
reference manager and CASP tool. Partial meta-analysis was carried
out and calculation of pooled effects and forest plotting were done.
As many as 13 studies finally included for final synthesis explained
the impact of targeted practices on health, behavioural and social
dimensions. Objectivity in the measurement of health outcomes
facilitated quantitative synthesis of studies which highlighted the
impact of sustainability methods on physical activity, Body Mass
Index, perinatal outcomes and child health. Studies synthesized
qualitatively (and also quantitatively) showed outcomes such as
routines, family relations, citizenship, trust in relationships, social
inclusion, neighbourhood social capital, wellbeing, habitability and
family’s social processes. The synthesized evidence indicates slight
effectiveness and efficacy of social and cultural sustainability on the
targeted outcomes. Further synthesis revealed that such results of this
study are due weak research designs and disintegrated implementations. If architects and other practitioners deliver their
interventions in collaboration with research bodies and policy
makers, a stronger evidence-base in this area could be generated.
Abstract: Despite the wide spread use of synthetic dyes, natural
dyes are still exploited and used to enhance its inherent aesthetic
qualities as a major material for beautification of the body. Centuries
before the discovery of synthetic dyes, natural dyes were the only
source of dye open to mankind. Dyes are extracted from plant -
leaves, roots and barks, insect secretions, and minerals. However,
research findings have made it clear that of all, plants- leaves, roots,
barks or flowers are the most explored and exploited in which henna
(Lawsonia innermis L.) is one of those plants. Experiment has also
shown that henna is used in body painting in conjunction with an
alkaline (Ammonium Sulphate) as a fixing agent. This of course
gives a clue that if colour derived from henna is properly
investigated, it may not only be used for body decoration but
possibly, may have affinity to fiber substrate. This paper investigates
the dyeing potentials – dye ability and fastness qualities of henna dye
extracts on cotton and linen fibers using mordants like ammonium
sulphate and other alkalis (hydrosulphate and caustic soda, potash,
common salt, potassium alum). Hot and cold water and ethanol
solvent were used in the extraction of the dye to investigate the most
effective method, dye ability, and fastness qualities of these extracts
under room temperature. The results of the experiment show that
cotton have a high rate of dye intake than other fiber. On a similar
note, the colours obtained depend most on the solvent used. In
conclusion, hot water extraction appears more effective. While the
colours obtained from ethanol and both cold hot methods of
extraction range from light to dark yellow, light green to army green
and to some extent shades of brown hues.
Abstract: This paper investigates the characteristics of wall
pressure fluctuations in naturally developing boundary layer flows
on axisymmetric bodies experimentally. The axisymmetric body has
a modified ellipsoidal blunt nose. Flush-mounted microphones are
used to measure the wall pressure fluctuations in the boundary layer
flow over the body. The measurements are performed in a low noise
wind tunnel. It is found that the correlation between the flow regime
and the characteristics of the pressure fluctuations is distinct. The
process from small fluctuation in laminar flow to large fluctuation in
turbulent flow is investigated. Tollmien-Schlichting wave (T-S wave)
is found to generate and develop in transition. Because of the T-S
wave, the wall pressure fluctuations in the transition region are higher
than those in the turbulent boundary layer.
Abstract: Segmentation of left ventricle (LV) from cardiac
ultrasound images provides a quantitative functional analysis of the
heart to diagnose disease. Active Shape Model (ASM) is widely used
for LV segmentation, but it suffers from the drawback that
initialization of the shape model is not sufficiently close to the target,
especially when dealing with abnormal shapes in disease. In this work,
a two-step framework is improved to achieve a fast and efficient LV
segmentation. First, a robust and efficient detection based on Hough
forest localizes cardiac feature points. Such feature points are used to
predict the initial fitting of the LV shape model. Second, ASM is
applied to further fit the LV shape model to the cardiac ultrasound
image. With the robust initialization, ASM is able to achieve more
accurate segmentation. The performance of the proposed method is
evaluated on a dataset of 810 cardiac ultrasound images that are mostly
abnormal shapes. This proposed method is compared with several
combinations of ASM and existing initialization methods. Our
experiment results demonstrate that accuracy of the proposed method
for feature point detection for initialization was 40% higher than the
existing methods. Moreover, the proposed method significantly
reduces the number of necessary ASM fitting loops and thus speeds up
the whole segmentation process. Therefore, the proposed method is
able to achieve more accurate and efficient segmentation results and is
applicable to unusual shapes of heart with cardiac diseases, such as left
atrial enlargement.
Abstract: Game-based learning can enhance the learning
motivation of students and provide a means for them to learn through
playing games. This study used augmented reality technology to
develop an interactive card game as a game-based teaching aid for
delivering elementary school science course content with the aim of
enhancing student learning processes and outcomes. Through playing
the proposed card game, students can familiarize themselves with
appearance, features, and foraging behaviors of insects. The system
records the actions of students, enabling teachers to determine their
students’ learning progress. In this study, 37 students participated in an
assessment experiment and provided feedback through questionnaires.
Their responses indicated that they were significantly more motivated
to learn after playing the game, and their feedback was mostly
positive.
Abstract: This research work is an experimental study, through
development of an adhesive from Prosopis africana endosperm. The
prosopis seed for this work were obtained from Enugu State in the
South East part of Nigeria. The seeds were prepared by separating the
endosperm from the seed coat and cotyledon. Three methods were
used to separate them, which are acidic method, roasting method and
boiling method. 20g of seed were treated with different
concentrations (25, 40, 55, 70, and 85% w/w) at 100°C and constant
time (30 minutes), under continuous stirring with magnetic stirrer.
Also 20g of seed were treated with sulphuric acid of concentrations
40% w/w at 100°C with different time (10, 15, 20, 25, 30 minutes),
under continuous stirring with magnetic stirrer. Finally, 20g of seed
were treated with sulphuric acid of concentrations 40% w/w at
different temperature (20°C, 40°C, 60°C, 80°C, and 100°C) with
constant time (30 minutes), under continuous stirring with magnetic
stirrer. The whole endosperm extracted was adhesive. The physical
properties of the adhesive were determined (appearance, odour, taste,
solubility, pH, size, and binding strength). The percentage of the
adhesive yield makes the commercialization of the seed in Nigeria
possible and profitable. The very high viscosity attained at low
concentrations makes prosopis adhesive an excellent thickener in the
food industry.
Abstract: The aim of this study is to examine, through
experimentation in the laboratory, the supercritical flow in the
presence of an obstacle in a rectangular channel. The supercritical
regime in the whole hydraulic channel is achieved by adding a
convergent. We will observe the influence of the obstacle shape and
dimension on the characteristics of the supercritical flow, mainly the
free-surface elevation and the velocity profile. The velocity
measurements have been conducted with the one dimension laser
anemometry technique.
Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: Searching the “Island of stability” is a topic of
extreme interest in theoretical as well as experimental modern
physics today. This “island of stability” is spanned by superheavy
elements (SHE's) that are produced in the laboratory. SHE's are
believed to exist primarily due to the “magic” stabilizing effects of
nuclear shell structure. SHE synthesis is extremely difficult due to
their very low production cross section, often of the order of pico
barns or less. Stabilizing effects of shell closures at proton number
Z=82 and neutron number N=126 are predicted theoretically. Though
stabilizing effects of Z=82 have been experimentally verified, no
concluding observations have been made with N=126, so far. We
measured and analyzed the total evaporation residue (ER) cross
sections for a number of systems with neutron number around 126 to
explore possible shell closure effects in ER cross sections, in this
work.