Abstract: Low temperature (LT) is one of the most abiotic
stresses causing loss of yield in wheat (T. aestivum). Four major
genes in wheat (Triticum aestivum L.) with the dominant alleles
designated Vrn–A1,Vrn–B1,Vrn–D1 and Vrn4, are known to have
large effects on the vernalization response, but the effects on cold
hardiness are ambiguous. Poor cold tolerance has restricted winter
wheat production in regions of high winter stress [9]. It was known
that nearly all wheat chromosomes [5] or at least 10 chromosomes of
21 chromosome pairs are important in winter hardiness [15]. The
objective of present study was to clarify the role of each chromosome
in cold tolerance. With this purpose we used 20 isogenic lines of
wheat. In each one of these isogenic lines only a chromosome from
‘Bezostaya’ variety (a winter habit cultivar) was substituted to
‘Capple desprez’ variety. The plant materials were planted in
controlled conditions with 20º C and 16 h day length in moderately
cold areas of Iran at Karaj Agricultural Research Station in 2006-07
and the acclimation period was completed for about 4 weeks in a
cold room with 4º C. The cold hardiness of these isogenic lines was
measured by LT50 (the temperature in which 50% of the plants are
killed by freezing stress).The experimental design was completely
randomized block design (RCBD)with three replicates. The results
showed that chromosome 5A had a major effect on freezing
tolerance, and then chromosomes 1A and 4A had less effect on this
trait. Further studies are essential to understanding the importance of
each chromosome in controlling cold hardiness in wheat.
Abstract: Distillation column is one of the most common
operations in process industries and is while the most expensive unit
of the amount of energy consumption. Many ideas have been
presented in the related literature for optimizing energy consumption
in distillation columns. This paper studies the different heat
integration methods in a distillation column which separate Benzene,
Toluene, Xylene, and C9+. Three schemes of heat integration
including, indirect sequence (IQ), indirect sequence with forward
energy integration (IQF), and indirect sequence with backward
energy integration (IQB) has been studied in this paper. Using
shortcut method these heat integration schemes were simulated with
Aspen HYSYS software and compared with each other with
regarding economic considerations. The result shows that the energy
consumption has been reduced 33% in IQF and 28% in IQB in
comparison with IQ scheme. Also the economic result shows that the
total annual cost has been reduced 12% in IQF and 8% in IQB
regarding with IQ scheme. Therefore, the IQF scheme is most
economic than IQB and IQ scheme.
Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.
Abstract: We report the results of an lattice Boltzmann
simulation of magnetohydrodynamic damping of sidewall convection
in a rectangular enclosure filled with a porous medium. In particular
we investigate the suppression of convection when a steady magnetic
field is applied in the vertical direction. The left and right vertical
walls of the cavity are kept at constant but different temperatures
while both the top and bottom horizontal walls are insulated. The
effects of the controlling parameters involved in the heat transfer and
hydrodynamic characteristics are studied in detail. The heat and mass
transfer mechanisms and the flow characteristics inside the enclosure
depended strongly on the strength of the magnetic field and Darcy
number. The average Nusselt number decreases with rising values of
the Hartmann number while this increases with increasing values of
the Darcy number.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: The combustion of liquid fuel in the porous burner
(PB) was experimented to investigate evaporation mechanism and
combustion behavior. The diesel oil was used as fuel and the pebbles
carefully chosen in the same size like the solid sphere homogeneously
was adopted as the porous media. Two structures of the liquid porous
burner, i.e. the PB without and with installation of porous emitter
(PE), were performed. PE was installed by lower than PB with
distance of 20 cm. The pebbles having porosity (φ) of 0.45 and 0.52
were, respectively, used in PB and PE. The fuel was supplied dropwise
from the top through the PB and the combustion was occurred between
PB and PE. Axial profiles of temperature along the burner length were
measured to clarify the evaporation and combustion phenomena. The
pollutant emission characteristics were monitored at the burner exit.
From the experiment, it was found that the temperature profiles of both
structures decreased with the three ways swirling air flows (QA)
increasing. On the other hand, the temperature profiles increased with
fuel heat input (QF). Obviously, the profile of the porous burner
installed with PE was higher than that of the porous burner without
PE
Abstract: Water recycling represents an important challenge for many countries, in particular in countries where this natural resource is rare. On the other hand, in many operations, water is used as a cooling medium, as a high proportion of water consumed in industry is used for cooling purposes. Generally this water is rejected directly to the nature. This reject will cause serious environment damages as well as an important waste of this precious element.. On way to solve these problems is to reuse and recycle this warm water, through the use of natural cooling medium, such as air in a heat exchanger unit, known as a cooling tower. A poor performance, design or reliability of cooling towers will result in lower flow rate of cooling water an increase in the evaporation of water, an hence losses of water and energy. This paper which presents an experimental investigate of thermal and hydraulic performances of a mechanical cooling tower, enables to show that the water evaporation rate, Mev, increases with an increase in the air and water flow rates, as well as inlet water temperature and for fixed air flow rates, the pressure drop (ΔPw/Z) increases with increasing , L, due to the hydrodynamic behavior of the air/water flow.
Abstract: A study was undertaken to investigate the effect of
liquid nitrogen aeration on mortalities of adult Cryptolestes
furrugineus, rusty grain beetles, in a prototype cardboard grain bin
equipped with an aeration system. The grain bin was filled with Hard
Red Spring wheat and liquid nitrogen was introduced from the bottom
of the bin. The survival of both cold acclimated and unacclimated C.
furrugineus was tested. The study reveals that cold acclimated insects
had higher survival than unacclimated insects under similar cooling
conditions. In most cases, mortalities of as high as 100% were
achieved at the bottom 100 cm of the grain bin for unacclimated
insects for most of the trials. Insect survival increased as the distance
from the bottom of the grain bin increased. There was no adverse
effect of liquid nitrogen aeration on wheat germination.
Abstract: Five lignin samples were fractionated with
Acetone/Water mixtures and the obtained fractions were subjected to
extensive structural characterization, including Fourier Transform
Infrared (FT-IR), Gel permeation Chromatography (GPC) and
Phosphorus-31 NMR spectroscopy (31P-NMR). The results showed
that for all studied lignins the solubility increases with the increment
of the acetone concentration. Wheat straw lignin has the highest
solubility in 90/10 (v/v) Acetone/Water mixture, 400 mg lignin being
dissolved in 1 mL mixture. The weight average molecular weight of
the obtained fractions increased with the increment of acetone
concentration and thus with solubility. 31P-NMR analysis based on
lignin modification by reactive phospholane into phosphitylated
compounds was used to differentiate and quantify the different types
of OH groups (aromatic, aliphatic, and carboxylic) found in the
fractions obtained with 70/30 (v/v) Acetone/Water mixture.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: There is a great deal of interest in constructing Double Skin Facade (DSF) structures which are considered as modern movement in field of Energy Conservation, renewable energies, and Architecture design. This trend provides many conclusive alternatives which are frequently associated with sustainable building. In this paper a building with Double Skin Facade is considered in the semiarid climate of Tehran, Iran, in order to consider the DSF-s performance during hot seasons. Mathematical formulations calculate solar heat gain by the external skin. Moreover, Computational Fluid Dynamics (CFD) simulations were performed on the case study building to enhance effectiveness of the facade. The conclusion divulged difference of gained energy by the cavity and room with and without blind and louvers. Some solutions were introduced to surge the performance of natural ventilation by plunging the cooling loads in summer.
Abstract: The present work consecutively on synthesis and
characterization of composites, Al/Al alloy A 384.1 as matrix in
which the main ingredient as Al/Al-5% MgO alloy based metal
matrix composite. As practical implications the low cost processing
route for the fabrication of Al alloy A 384.1 and operational
difficulties of presently available manufacturing processes based in
liquid manipulation methods. As all new developments, complete
understanding of the influence of processing variables upon the final
quality of the product. And the composite is applied comprehensively
to the acquaintance for achieving superiority of information
concerning the specific heat measurement of a material through the
aid of thermographs. Products are evaluated concerning relative
particle size and mechanical behavior under tensile strength.
Furthermore, Taguchi technique was employed to examine the
experimental optimum results are achieved, owing to effectiveness of
this approach.
Abstract: The present study is concerned with the absorption
center of photophoresis within a micro-sized and spheroidal particle in
a gaseous medium. A particle subjected to an intense light beam can
absorb electromagnetic energy within the particle unevenly, which
results in photophoretic force to drive the particle in motion. By
evaluating the energy distribution systematically at various conditions,
the study focuses on the effects of governing parameters, such as
particle aspect ratio, size parameter, refractivity, and absorptivity, on
the heat source function within the particle and their potential
influences to the photophoresis.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: The most severe damage of the turbine rotor is its
distortion. The rotor straightening process must lead, at the first
stage, to removal of the stresses from the material by annealing and
next, to straightening of the plastic distortion without leaving any
stress by hot spotting. The straightening method does not produce
stress accumulations and the heating technique, developed
specifically for solid forged rotors and disks, enables to avoid local
overheating and structural changes in the material. This process also
does not leave stresses in the shaft material. An experimental study
of hot spotting is carried out on a large turbine rotor and some of the
most important effective parameters that must be considered on
annealing and hot spotting processes are investigated in this paper.
Abstract: The organic farmers use wider range of crop varieties than the conventional farming. Bread wheat is the most favorite and the most common food crop. The organic bread wheat is usually of worse technological quality. Therefore, it is supposed to be an attractive alternative to the hulled wheat species (einkorn, emmer wheat and spelt). Twenty-five hulled bread wheat varieties and control bread wheat ones were grown on the certified organic parcel in České Budějovice (the Czech Republic) between 2009 and 2012. Their baking quality was measured and evaluated with standard methods, and in accordance with ICC. The results have shown that the grain of hulled wheat varieties contain a lot of proteins in grains (up to 18 percent); even the organic hulled bread wheat varieties are characterized by such good baking quality. Einkorn and emmer wheat are of worse technological quality of proteins (low values of gluten index and Zeleny test), which is a disadvantage of these two wheat species. On the other hand, spelt wheat is of better technological quality and is similar to the control bread wheat varieties. Mixtures consisting of bread wheat, among others, are considered good alternatives; they may contribute to wider range of use of the hulled wheat species. It is one of the possibilities which may increase the proportion of proteins in bread wheat grains; the nutrition-rich hulled wheat grains may be also used in such way at the same time.
Abstract: In the present work an investigation of the effects of
the air frontal velocity, relative humidity and dry air temperature on
the heat transfer characteristics of plain finned tube evaporator has
been conducted. Using an appropriate correlation for the air side heat
transfer coefficient the temperature distribution along the fin surface
was calculated using a dimensionless temperature distribution. For a
constant relative humidity and bulb temperature, it is found that the
temperature distribution decreases with increasing air frontal
velocity. Apparently, it is attributed to the condensate water film
flowing over the fin surface. When dry air temperature and face
velocity are being kept constant, the temperature distribution
decreases with the increase of inlet relative humidity. An increase in
the inlet relative humidity is accompanied by a higher amount of
moisture on the fin surface. This results in a higher amount of latent
heat transfer which involves higher fin surface temperature. For the
influence of dry air temperature, the results here show an increase in
the dimensionless temperature parameter with a decrease in bulb
temperature. Increasing bulb temperature leads to higher amount of
sensible and latent heat transfer when other conditions remain
constant.
Abstract: Twelve lactating Etawah Crossedbred goats were used
in this study. Goat feed consisted of Cally andra callothyrsus,
Pennisetum purpureum, wheat bran and dried fermented cassava
peel. The cassava peels were fermented with a traditional culture
called “ragi tape" (mixed culture of Saccharomyces cerevisae,
Aspergillus sp, Candida, Hasnula and Acetobacter). The goats were
divided into 2 groups (Control and Treated) of six does. The
experimental diet of the Control group consisted of 70% of roughage
(fresh Callyandra callothyrsus and Pennisetum purpureum 60:40)
and 30% of wheat bran on dry matter (DM) base. In the Treated
group 30% of wheat bran was replaced with dried fermented cassava
peels. Data were statistically analyzed using analysis of variance
followed SPSS program. The concentration of HCN in fermented
cassava peel decreased to non toxic level. Nutrient composition of
dried fermented cassava peel consisted of 85.75% dry matter;
5.80% crude protein and 82.51% total digestible nutrien (TDN).
Substitution of 30% of wheat bran with dried fermented cassava peel
in the diet had no effect on dry matter and organic matter intake but
significantly (P< 0.05) decreased crude protein and TDN
consumption as well as milk yields and milk composition. The study
recommended to reduced the level of substitution to less than 30% of
concentrates in the diet in order to avoid low nutrient intake and milk
production of goats.
Abstract: Nowadays, there is little information, concerning the
heat shield systems, and this information is not completely reliable to
use in so many cases. for example, the precise calculation cannot be
done for various materials. In addition, the real scale test has two
disadvantages: high cost and low flexibility, and for each case we
must perform a new test. Hence, using numerical modeling program
that calculates the surface recession rate and interior temperature
distribution is necessary. Also, numerical solution of governing
equation for non-charring material ablation is presented in order to
anticipate the recession rate and the heat response of non-charring
heat shields. the governing equation is nonlinear and the Newton-
Rafson method along with TDMA algorithm is used to solve this
nonlinear equation system. Using Newton- Rafson method for
solving the governing equation is one of the advantages of the
solving method because this method is simple and it can be easily
generalized to more difficult problems. The obtained results
compared with reliable sources in order to examine the accuracy of
compiling code.