Abstract: Accurate timing alignment and stability is important
to maximize the true counts and minimize the random counts in
positron emission tomography So signals output from detectors must
be centering with the two isotopes to pre-operation and fed signals
into four units of pulse-processing units, each unit can accept up to
eight inputs. The dual source computed tomography consist two units
on the left for 15 detector signals of Cs-137 isotope and two units on
the right are for 15 detectors signals of Co-60 isotope. The gamma
spectrum consisting of either single or multiple photo peaks. This
allows for the use of energy discrimination electronic hardware
associated with the data acquisition system to acquire photon counts
data with a specific energy, even if poor energy resolution detectors
are used. This also helps to avoid counting of the Compton scatter
counts especially if a single discrete gamma photo peak is emitted by
the source as in the case of Cs-137. In this study the polyenergetic
version of the alternating minimization algorithm is applied to the
dual energy gamma computed tomography problem.
Abstract: In this paper, the residual stress of thermal spray
coatings in gas turbine component by curvature method has been
studied. The samples and shaft were coated by hard WC-12Co
cermets using high velocity oxy fuel (HVOF) after preparation in
same conditions. The curvature of coated samples was measured by
using of coordinate measurement machine (CMM). The metallurgical
and Tribological studies has been made on the coated shaft using
optical microscopy and scanning electron microscopy (SEM)
Abstract: Rutting is one of the major load-related distresses in airport flexible pavements. Rutting in paving materials develop gradually with an increasing number of load applications, usually appearing as longitudinal depressions in the wheel paths and it may be accompanied by small upheavals to the sides. Significant research has been conducted to determine the factors which affect rutting and how they can be controlled. Using the experimental design concepts, a series of tests can be conducted while varying levels of different parameters, which could be the cause for rutting in airport flexible pavements. If proper experimental design is done, the results obtained from these tests can give a better insight into the causes of rutting and the presence of interactions and synergisms among the system variables which have influence on rutting. Although traditionally, laboratory experiments are conducted in a controlled fashion to understand the statistical interaction of variables in such situations, this study is an attempt to identify the critical system variables influencing airport flexible pavement rut depth from a statistical DoE perspective using real field data from a full-scale test facility. The test results do strongly indicate that the response (rut depth) has too much noise in it and it would not allow determination of a good model. From a statistical DoE perspective, two major changes proposed for this experiment are: (1) actual replication of the tests is definitely required, (2) nuisance variables need to be identified and blocked properly. Further investigation is necessary to determine possible sources of noise in the experiment.
Abstract: Composite nanostructures of metal
core/semiconductor shell (Au/CdS) configuration were prepared
using organometalic method. UV-Vis spectra for the Au/CdS colloids
show initially two well separated bands, corresponding to surface
plasmon of the Au core, and the exciton of CdS shell. The absorption
of CdS shell is enhanced, while the Au plasmon band is suppressed
as the shell thickness increases. The shell sizes were estimated from
the optical spectra using the effective mass approximation model
(EMA), and compared to the sizes of the Au core and CdS shell
measured by high resolution transmission electron microscope
(HRTEM). The changes in the absorption features are discussed in
terms of gradual increase in the coupling strength of the Au core
surface plasmon and the exciton in the CdS. leading to charge
transfer and modification of electron oscillation in Au core.
Abstract: The modern world is experiencing fundamental and dynamic changes. The transformation of international relations; the end of confrontation and successive overcoming of the Cold War consequences have expanded possible international cooperation. The global nuclear conflict threat has been minimized, while a tendency to establish a unipolar world structure with the U.S. economic and power domination is growing. The current world system of international relations, apparently is secular. However, the religious beliefs of one or another nations play a certain (sometimes a key) role, both in the domestic affairs of the individual countries and in the development of bilateral ties. Political situation in Central Asia has been characterized by new factors such as international terrorism; religious extremism and radicalism; narcotrafficking and illicit arms trade of a global character immediately threaten to peace and political stability in Central Asia. The role and influence of Islamic fundamentalism is increasing; political ethnocentrism and the associated aggravation of inter-ethnic relations, the ambiguity of national interests and objectives of major geo-political groups in the Central Asian region regarding the division the political influence, emerge. This article approaches the following issues: the role of Islam in Central Asia; destabilizing factors in Central Asia; Islamic movements in Central Asia, Western Europe and the United States; the United States, Western Europe and Central Asia: religion, politics, ideology, and the US-Central Asia antiterrorism and religious extremism cooperation.
Abstract: The optimal design of PI controller for Automatic Generation Control in two area is presented in this paper. The concept of Dual mode control is applied in the PI controller, such that the proportional mode is made active when the rate of change of the error is sufficiently larger than a specified limit otherwise switched to the integral mode. A digital simulation is used in conjunction with the Hooke-Jeeve’s optimization technique to determine the optimum parameters (individual gain of proportional and integral controller) of the PI controller. Integrated Square of the Error (ISE), Integrated Time multiplied by Absolute Error(ITAE) , and Integrated Absolute Error(IAE) performance indices are considered to measure the appropriateness of the designed controller. The proposed controller are tested for a two area single nonreheat thermal system considering the practical aspect of the problem such as Deadband and Generation Rate Constraint(GRC). Simulation results show that dual mode with optimized values of the gains improved the control performance than the commonly used Variable Structure .
Abstract: Nowadays, organizations and business has several motivating factors to protect an individual-s privacy. Confidentiality refers to type of sharing information to third parties. This is always referring to private information, especially for personal information that usually needs to keep as a private. Because of the important of privacy concerns today, we need to design a database system that suits with privacy. Agrawal et. al. has introduced Hippocratic Database also we refer here as a privacy-aware database. This paper will explain how HD can be a future trend for web-based application to enhance their privacy level of trustworthiness among internet users.
Abstract: The electrical substation components are often subject to degradation due to over-voltage or over-current, caused by a short circuit or a lightning. A particular interest is given to the circuit breaker, regarding the importance of its function and its dangerous failure. This component degrades gradually due to the use, and it is also subject to the shock process resulted from the stress of isolating the fault when a short circuit occurs in the system. In this paper, based on failure mechanisms developments, the wear out of the circuit breaker contacts is modeled. The aim of this work is to evaluate its reliability and consequently its residual lifetime. The shock process is based on two random variables such as: the arrival of shocks and their magnitudes. The arrival of shocks was modeled using homogeneous Poisson process (HPP). By simulation, the dates of short-circuit arrivals were generated accompanied with their magnitudes. The same principle of simulation is applied to the amount of cumulative wear out contacts. The objective reached is to find the formulation of the wear function depending on the number of solicitations of the circuit breaker.
Abstract: The main objective of this work is to provide a fault detection and isolation based on Markov parameters for residual generation and a neural network for fault classification. The diagnostic approach is accomplished in two steps: In step 1, the system is identified using a series of input / output variables through an identification algorithm. In step 2, the fault is diagnosed comparing the Markov parameters of faulty and non faulty systems. The Artificial Neural Network is trained using predetermined faulty conditions serves to classify the unknown fault. In step 1, the identification is done by first formulating a Hankel matrix out of Input/ output variables and then decomposing the matrix via singular value decomposition technique. For identifying the system online sliding window approach is adopted wherein an open slit slides over a subset of 'n' input/output variables. The faults are introduced at arbitrary instances and the identification is carried out in online. Fault residues are extracted making a comparison of the first five Markov parameters of faulty and non faulty systems. The proposed diagnostic approach is illustrated on benchmark problems with encouraging results.
Abstract: Portuguese diet has been gradually diverging from the basic principles of healthy eating, leading to an unbalanced dietary pattern which, associated with increasing sedentary lifestyle, has a negative impact on public health. The main objective of this work was to characterize the dietary habits of university students in Viseu, Portugal. The study consisted of a sample of 80 university students, aged between 18 and 28 years. Anthropometric data (weight (kg) and height (m)) were collected and Body Mass Index (BMI) was calculated. The dietary habits were assessed through a three-day food record and the software Medpoint was used to convert food into energy and nutrients. The results showed that students present a normal body mass index. Female university students made a higher number of daily meals than male students, and these last skipped breakfast more frequently. The values of average daily intake of energy, macronutrients and calcium were higher in males. The food pattern was characterized by a predominant consumption of meat, cereal, fats and sugar. Dietary intake of dairy products, fruits, vegetables and legumes does not meet the recommendations, revealing inadequate food habits such as hypoglycemic, hyperprotein and hyperlipidemic diet. Our findings suggest that preventive interventions should be focus in promoting healthy eating habits and physical activity in adulthood.
Abstract: A new and cost effective robotic device was designed
for remote tele surgery using dual tone multi frequency technology
(DTMF). Tele system with Dual Tone Multiple Frequency has a large
capability in sending and receiving of data in hardware and software.
The robot consists of DC motors for arm movements and it is
controlled manually through a mobile phone through DTMF
Technology. The system enables the surgeon from base station to
send commands through mobile phone to the patient’s robotic system
which includes two robotic arms that translate the input into actual
instrument manipulation. A mobile phone attached to the
microcontroller 8051 which can activate robot through relays. The
Remote robot-assisted tele surgery eliminates geographic constraints
for getting surgical expertise where it is needed and allows an expert
surgeon to teach or proctor the performance of surgical technique by
real-time intervention.
Abstract: The globe Sustainability has become the subject of international attention, the key reason is that global climate change. Climate and disasters around the abnormal frequency multiplier, the global temperature of the catastrophe and disaster continue to occur throughout the world, as well as countries around the world. Currently there are many important international conferences and policy, it is a "global environmental sustainability " and "living human health " as the goal of development, including the APEC 2007 meeting to "climate Clean Energy" as the theme Sydney Declaration, 2008 World Economic Forum's "Carbon - promote Cool Earth energy efficiency improvement project", the EU proposed "Green Idea" program, the Japanese annual policy, "low-carbon society, sustainable eco-city environment (Eco City) "And from 2009 to 2010 to promote the "Eco-Point" to promote green energy and carbon reduction products .And the 2010 World Climate Change Conference (COP16 United Nations Climate Change Conference Copenhagen), the world has been the subject of Negative conservative "Environmental Protection ", "save energy consumption, " into a positive response to the "Sustainable " and" LOHAS", while Taiwan has actively put forward eco-cities, green building, green building materials and other related environmental response Measures, especially green building construction environment that is the basis of factors, the most widely used application level, and direct contact with human health and the key to sustainable planet. "Sustainable development "is a necessary condition for continuation of the Earth, "healthy and comfortable" is a necessary condition for the continuation of life, and improve the "quality" is a necessary condition for economic development, balance between the three is "to enhance the efficiency of ", According to the World Business Council for Sustainable Development (WBCSD) for the "environmental efficiency "(Eco-Efficiency) proposed: " the achievement of environmental efficiency, the price to be competitive in the provision of goods or services to meet people's needs, improve living Quality at the same time, the goods or services throughout the life cycle. Its impact on the environment and natural resource utilization and gradually reduced to the extent the Earth can load. "whichever is the economy "Economic" and " Ecologic". The research into the methodology to obtain the Taiwan Green Building Material Labeling product as the scope of the study, by investigating and weight analysis to explore green building environmental load (Ln) factor and the Green Building Quality (Qn) factor to Establish green building environmental efficiency assessment model (GBM Eco-Efficiency). And building materials for healthy green label products for priority assessment object, the object is set in the material evidence for the direct response to the environmental load from the floor class-based, explicit feedback correction to the Green Building environmental efficiency assessment model, "efficiency " as a starting point to achieve balance between human "health "and Earth "sustainable development of win-win strategy. The study is expected to reach 1.To establish green building materials and the quality of environmental impact assessment system, 2. To establish value of GBM Eco-Efficiency model, 3. To establish the GBM Eco-Efficiency model for application of green building material feedback mechanisms.
Abstract: Sensitive and predictive DILI (Drug Induced Liver
Injury) biomarkers are needed in drug R&D to improve early
detection of hepatotoxicity. The discovery of DILI biomarkers that
demonstrate the predictive power to identify individuals at risk to
DILI would represent a major advance in the development of
personalized healthcare approaches. In this healthy volunteer
acetaminophen study (4g/day for 7 days, with 3 monitored nontreatment
days before and 4 after), 450 serum samples from 32
subjects were analyzed using protein profiling by antibody
suspension bead arrays. Multiparallel protein profiles were generated
using a DILI target protein array with 300 antibodies, where the
antibodies were selected based on previous literature findings of
putative DILI biomarkers and a screening process using pre dose
samples from the same cohort. Of the 32 subjects, 16 were found to
develop an elevated ALT value (2Xbaseline, responders). Using the
plasma profiling approach together with multivariate statistical
analysis some novel findings linked to lipid metabolism were found
and more important, endogenous protein profiles in baseline samples
(prior to treatment) with predictive power for ALT elevations were
identified.
Abstract: In this paper, we propose a dual version of the first
threshold ring signature scheme based on error-correcting code proposed
by Aguilar et. al in [1]. Our scheme uses an improvement of
Véron zero-knowledge identification scheme, which provide smaller
public and private key sizes and better computation complexity than
the Stern one. This scheme is secure in the random oracle model.
Abstract: In today-s information age, numbers of organizations
are still arguing on capitalizing the values of Information Technology
(IT) and Knowledge Management (KM) to which individuals can
benefit from and effective communication among the individuals can
be established. IT exists in enabling positive improvement for
communication among knowledge workers (k-workers) with a
number of social network technology domains at workplace. The
acceptance of digital discourse in sharing of knowledge and
facilitating the knowledge and information flows at most of the
organizations indeed impose the culture of knowledge sharing in
Digital Social Networks (DSN). Therefore, this study examines
whether the k-workers with IT background would confer an effect on
the three knowledge characteristics -- conceptual, contextual, and
operational. Derived from these three knowledge characteristics, five
potential factors will be examined on the effects of knowledge
exchange via e-mail domain as the chosen query. It is expected, that
the results could provide such a parameter in exploring how DSN
contributes in supporting the k-workers- virtues, performance and
qualities as well as revealing the mutual point between IT and KM.
Abstract: Telemedicine is brought to life by contemporary changes of our world and summarizes the entire range of services that are at the crossroad of traditional healthcare and information technology. It is believed that eHealth can help in solving critical issues of rising costs, care for ageing and housebound population, staff shortage. It is a feasible tool to provide routine as well as specialized health service as it has the potential to improve both the access to and the standard of care. eHealth is no more an optional choice. It has already made quite a way but it still remains a fantastic challenge for the future requiring cooperation and coordination at all possible levels. The strategic objectives of this paper are: 1. To start with an attempt to clarify the mass of terms used nowadays; 2. To answer the question “Who needs eHealth"; 3. To focus on the necessity of bridging telemedicine and medical (health) informatics as well as on the dual relationship between them; as well as 4. To underline the need of networking in understanding, developing and implementing eHealth.
Abstract: A water reuse system in wetland paddy was simulated
to supply water for industrial in this paper. A two-tank model was employed to represent the return flow of the wetland paddy.Historical data were performed for parameter estimation and model verification. With parameters estimated from the data, the model was then used to simulate a reasonable return flow rate from the wetland
paddy. The simulation results show that the return flow ratio was 11.56% in the first crop season and 35.66% in the second crop
season individually; the difference may result from the heavy rainfall in the second crop season. Under the existent pond with surplus
active capacity, the water reuse ratio was 17.14%, and the water supplementary ratio was 21.56%. However, the pattern of rainfall, the
active capacity of the pond, and the rate of water treatment limit the
volume of reuse water. Increasing the irrigation water, dredging the
depth of pond before rainy season and enlarging the scale of module are help to develop water reuse system to support for the industrial
water use around wetland paddy.
Abstract: A low bit rate still image compression scheme by
compressing the indices of Vector Quantization (VQ) and generating
residual codebook is proposed. The indices of VQ are compressed by
exploiting correlation among image blocks, which reduces the bit per
index. A residual codebook similar to VQ codebook is generated that
represents the distortion produced in VQ. Using this residual
codebook the distortion in the reconstructed image is removed,
thereby increasing the image quality. Our scheme combines these two
methods. Experimental results on standard image Lena show that our
scheme can give a reconstructed image with a PSNR value of 31.6 db
at 0.396 bits per pixel. Our scheme is also faster than the existing VQ
variants.
Abstract: The aim of this paper is to rank the impact of Object
Oriented(OO) metrics in fault prediction modeling using Artificial
Neural Networks(ANNs). Past studies on empirical validation of
object oriented metrics as fault predictors using ANNs have focused
on the predictive quality of neural networks versus standard
statistical techniques. In this empirical study we turn our attention to
the capability of ANNs in ranking the impact of these explanatory
metrics on fault proneness. In ANNs data analysis approach, there is
no clear method of ranking the impact of individual metrics. Five
ANN based techniques are studied which rank object oriented
metrics in predicting fault proneness of classes. These techniques are
i) overall connection weights method ii) Garson-s method iii) The
partial derivatives methods iv) The Input Perturb method v) the
classical stepwise methods. We develop and evaluate different
prediction models based on the ranking of the metrics by the
individual techniques. The models based on overall connection
weights and partial derivatives methods have been found to be most
accurate.
Abstract: The private theme parks are gradually surpassing
public-owned scenic areas after many years of development and have
become a mainstream choice for domestic tourists. Previous studies
show that visitors from different backgrounds differ in consumer
behavior and satisfaction factors. An understanding of visitor
satisfaction is therefore of extreme importance to operators of
privately-owned theme parks. Importance-Performance Analysis (IPA)
is used to measure consumer's potential satisfaction with services and
has become a widely used management tool for strength and weakness
analysis for brands, products, services and point of sales. As IPA has
so far not been used to evaluate the visitor satisfaction with
privately-owned theme parks, in this study the IPA method is used to
analyze visitor satisfaction with Janfusun Fancyworld (one of the most
popular private theme parks in Taiwan) and to rank visitor focus and
satisfaction on/in theme park facilities and services. Results of the
analysis provide private theme park operators with an understanding
of user or consumer demands as well as an assessment of the quality of
services currently offered.