Abstract: A pressure-based implicit procedure to solve Navier-
Stokes equations on a nonorthogonal mesh with collocated finite
volume formulation is used to simulate flow around the smart and
conventional flaps of spoiler under the ground effect. Cantilever
beam with uniformly varying load with roller support at the free end
is considered for smart flaps. The boundedness criteria for this
procedure are determined from a Normalized Variable diagram
(NVD) scheme. The procedure incorporates es the k -ε eddyviscosity
turbulence model. The method is first validated against
experimental data. Then, the algorithm is applied for turbulent
aerodynamic flows around a spoiler section with smart and
conventional flaps for different attack angle, flap angle and ground
clearance where the results of two flaps are compared.
Abstract: Wall-surface jet induced by the dielectric barrier
discharge (DBD) has been proposed as an actuator for active flow
control in aerodynamic applications. Discharge plasma evolution of
the DBD plasma actuator was simulated based on a simple fluid model,
in which the electron, one type of positive ion and negative ion were
taken into account. Two-dimensional simulation was conducted, and
the results are in agreement with the insights obtained from
experimental studies. The simulation results indicate that the discharge
mode changes depending on applied voltage slope; when the applied
voltage is positive-going with high applied voltage slope, the
corona-type discharge mode turns into the streamer-type discharge
mode and the threshold voltage slope is around 300 kV/ms in this
simulation. The characteristics of the electrohydrodynamic (EHD)
force, which is the source of the wall-surface jet, also change
depending on the discharge mode; the tentative peak value of the EHD
force during the positive-going voltage phase is saturated by the
periodical formation of the streamer-type discharge.
Abstract: Evaporator is an important and widely used heat
exchanger in air conditioning and refrigeration industries. Different
methods have been used by investigators to increase the heat transfer
rates in evaporators. One of the passive techniques to enhance heat
transfer coefficient is the application of microfin tubes. The
mechanism of heat transfer augmentation in microfin tubes is
dependent on the flow regime of two-phase flow. Therefore many
investigations of the flow patterns for in-tube evaporation have been
reported in literatures. The gravitational force, surface tension and
the vapor-liquid interfacial shear stress are known as three dominant
factors controlling the vapor and liquid distribution inside the tube. A
review of the existing literature reveals that the previous
investigations were concerned with the two-phase flow pattern for
flow boiling in horizontal tubes [12], [9]. Therefore, the objective of
the present investigation is to obtain information about the two-phase
flow patterns for evaporation of R-134a inside horizontal smooth and
microfin tubes. Also Investigation of heat transfer during flow
boiling of R-134a inside horizontal microfin and smooth tube have
been carried out experimentally The heat transfer coefficients for
annular flow in the smooth tube is shown to agree well with Gungor
and Winterton-s correlation [4]. All the flow patterns occurred in the
test can be divided into three dominant regimes, i.e., stratified-wavy
flow, wavy-annular flow and annular flow. Experimental data are
plotted in two kinds of flow maps, i.e., Weber number for the vapor
versus weber number for the liquid flow map and mass flux versus
vapor quality flow map. The transition from wavy-annular flow to
annular or stratified-wavy flow is identified in the flow maps.
Abstract: The soil ecology of the organic and mineral soil layers
of laurel-leaved and Cryptomeria japonica forest in the Kasuga-yama
Hill Primeval Forest (Nara, Japan) was assessed. The number of
bacteria obtained by the dilution plate count method was less than
0.05% of those counted by the direct microscopic count. We therefore
found that forest soil contains large numbers of non-culturable
bacteria compared with agricultural soils. The numbers of bacteria and
fungi obtained by both the dilution plate count and the direct
microscopic count were larger in the deeper horizons (F and H) of the
organic layer than in the mineral soil layer. This suggests that active
microbial metabolism takes place in the organic layer. The numbers of
bacteria and the length of fungal hyphae obtained by the direct count
method were greater in the H horizon than in the F horizon. The direct
microscopic count revealed numerous non-culturable bacteria and
fungi in the soil. The ratio of fungal to bacterial biomass was lower in
the laurel-leaved forest soil. The fungal biomass was therefore
relatively low in the laurel-leaved forest soil due to differences in
forest vegetation.
Abstract: Preliminary results for a new flat plate test
facility are presented here in the form of Computational Fluid Dynamics (CFD), flow visualisation, pressure measurements and thermal anemometry. The results from the CFD and flow
visualisation show the effectiveness of the plate design, with the trailing edge flap anchoring the stagnation point on the working surface and reducing the extent of the leading edge separation. The flow visualization technique demonstrates the
two-dimensionality of the flow in the location where the
thermal anemometry measurements are obtained.
Measurements of the boundary layer mean velocity profiles compare favourably with the Blasius solution, thereby allowing for comparison of future measurements with the
wealth of data available on zero pressure gradient Blasius
flows. Results for the skin friction, boundary layer thickness,
frictional velocity and wall shear stress are shown to agree well with the Blasius theory, with a maximum experimental deviation from theory of 5%. Two turbulence generating grids
have been designed and characterized and it is shown that the turbulence decay downstream of both grids agrees with established correlations. It is also demonstrated that there is
little dependence of turbulence on the freestream velocity.
Abstract: In this paper, Novel method, Particle Swarm Optimization (PSO) algorithm, based technique is proposed to estimate and analyze the steady state performance of self-excited induction generator (SEIG). In this novel method the tedious job of deriving the complex coefficients of a polynomial equation and solving it, as in previous methods, is not required. By comparing the simulation results obtained by the proposed method with those obtained by the well known mathematical methods, a good agreement between these results is obtained. The comparison validates the effectiveness of the proposed technique.
Abstract: In this paper, we generalize some propositions in [C.Z. Wang, D.G. Chen, A short note on some properties of rough groups, Comput. Math. Appl. 59(2010)431-436.] and we give some equivalent conditions for rough subgroups. The notion of minimal upper rough subgroups is introduced and a equivalent characterization is given, which implies the rough version of Lagranges Theorem.
Abstract: Hydrate phase equilibria for the binary CO2+water and
CH4+water mixtures in silica gel pore of nominal diameters 6, 30, and
100 nm were measured and compared with the calculated results based
on van der Waals and Platteeuw model. At a specific temperature,
three-phase hydrate-water-vapor (HLV) equilibrium curves for pore
hydrates were shifted to the higher-pressure condition depending on
pore sizes when compared with those of bulk hydrates. Notably,
hydrate phase equilibria for the case of 100 nominal nm pore size were
nearly identical with those of bulk hydrates. The activities of water in
porous silica gels were modified to account for capillary effect, and
the calculation results were generally in good agreement with the
experimental data. The structural characteristics of gas hydrates in
silica gel pores were investigated through NMR spectroscopy.
Abstract: Growth and mineral nutrient elemental content were
studied in Mokara chark kuan pink terrestrial orchid and wild
Lantana camara weed agroecosystem. The treated subplots were
encircled with L. camara plants and sprayed weekly with L. camara
10% leaf aqueous extract. Allelopathic interactions were possible
through extensive invading root of L. camara plants into the treated
orchid subplots and weekly L. camara leaf aqueous extract
sprayings. Orchid growth was not significantly different in between
the control and treated plots, but chlorosis and yellowish patches of
leaves were observed in control orchid leaves. Nitrogen content in L.
camara leaf was significantly higher than in orchid leaf, the order of
importance of mineral nutrient contents in L. camara leaf was
K>Mg>Na>N. In treated orchid leaf, the order of importance was
N>K>Mg>Na. Orchid leaf N content from the treated plot was
higher than control, but Mg and Na contents were almost similar.
Abstract: The effect of seed inoculation by VA- mycorrhiza and
different levels of phosphorus fertilizer on growth and yield of
sunflower (Azargol cultivar) was studied in experiment farm of
Islamic Azad University, Karaj Branch during 2008 growing season.
The experiment treatments were arranged in factorial based on a
complete randomized block design with three replications. Four
phosphorus fertilizer levels of 25%, 50% 75% and 100% P
recommended with two levels of Mycorrhiza: with and without
Mycorrhiza (control) were assigned in a factorial combination.
Results showed that head diameter, number of seeds in head, seed
yield and oil yield were significantly higher in inoculated plants than
in non-inoculated plants. Head diameter, number of seeds in head,
1000 seeds weight, biological yield, seed yield and oil yield increased
with increasing P level above 75% P recommended in non-inoculated
plants, whereas no significant difference was observed between 75%
and 100% P recommended. The positive effect of mycorrhizal
inoculation decreased with increasing P levels due to decreased
percent root colonization at higher P levels. According to the results
of this experiment, application of mycorrhiza in present of 50% P
recommended had an appropriate performance and could increase
seed yield and oil production to an acceptable level, so it could be
considered as a suitable substitute for chemical phosphorus fertilizer
in organic agricultural systems.
Abstract: The Chichiawan stream in the Wulin catchment in
Taiwan is the natural habitat of Formosan landlocked salmon. Human
and agriculture activities gradually worsen water quality and impact
the fish habitat negatively. To protect and manage Formosan
landlocked salmon habitat, it is important to understand a variety
land-uses affect on the watershed responses to storms. This study
discusses watershed responses to the dry-day before a storm event and
a variety of land-uses in the Wulin catchment. Under the land-use
planning in the Wulin catchment, the peak flows during typhoon
events do not have noticeable difference. However, the nutrient
exports can be highly reduced under the strategies of restraining
agriculture activities. Due to the higher affinity of P for soil than that
of N, the exports of TN from overall Wuling catchment were much
greater than Ortho-P. Agriculture mainly centralized in subbasin A,
which is the important source of nutrients in nonpoint source discharge.
The subbasin A supplied about 26% of the TN and 32% of the Ortho-P
discharge in 2004, despite the fact it only covers 19% area of the
Wuling catchment. The subbasin analysis displayed that the
agricultural subbasin A exports higher nutrients per unit area than
other forest subbasins. Additionally, the agricultural subbasin A
contributed a higher percentage to total Ortho-P exports compares to
TN. The results of subbasin analysis might imply the transport of
Ortho-P was similar to the particulate matter which was mainly
influenced by the runoff and affected by the desorption from soil
particles while the TN (dominated as nitrate-N) was mainly influenced
by base-flow.
Abstract: An evaluation of the PCBs residues in the surface soils from Bacninh, Vietnam was carried out. Sixty representative soil samples were collected from the centre of Bacninh and three surrounding districts. The analyzed results indicated the wide extent of contamination of total PCBs in Bacninh. In industrial and urban zones, total PCBs concentrations ranged from ranged from
Abstract: The use of renewable energy sources incl. biogas has become topical in accordance with the increasing demand for energy, decrease of fossil energy resources and the efforts to reduce greenhouse gas emissions as well as to increase energy independence from the territories where fossil energy resources are available.
As the technologies of biogas production from agricultural biomass develop, risk assessment and risk management become necessary for farms producing such a renewable energy. The need for risk assessments has become particularly topical when discussions on changing the biogas policy in the EU take place, which may influence the development of the sector in the future, as well as the operation of existing biogas facilities and their income level.
The current article describes results of the risk assessment for farms producing biomass from agriculture biomass in Latvia, the risk assessment system included 24 risks, that affect the whole biogas production process and the obtained results showed the high significance of political and production risks.
Abstract: Business Process Modeling (BPM) is the first and
most important step in business process management lifecycle. Graph
based formalism and rule based formalism are the two most
predominant formalisms on which process modeling languages are
developed. BPM technology continues to face challenges in coping
with dynamic business environments where requirements and goals
are constantly changing at the execution time. Graph based
formalisms incur problems to react to dynamic changes in Business
Process (BP) at the runtime instances. In this research, an adaptive
and flexible framework based on the integration between Object
Oriented diagramming technique and Petri Net modeling language is
proposed in order to support change management techniques for
BPM and increase the representation capability for Object Oriented
modeling for the dynamic changes in the runtime instances. The
proposed framework is applied in a higher education environment to
achieve flexible, updatable and dynamic BP.
Abstract: The Model for Knowledge Base of Computational Objects
(KBCO model) has been successfully applied to represent the
knowledge of human like Plane Geometry, Physical, Calculus. However,
the original model cannot easyly apply in inorganic chemistry
field because of the knowledge specific problems. So, the aim of
this article is to introduce how we extend the Computional Object
(Com-Object) in KBCO model, kinds of fact, problems model, and
inference algorithms to develop a program for solving problems
in inorganic chemistry. Our purpose is to develop the application
that can help students in their study inorganic chemistry at schools.
This application was built successful by using Maple, C# and WPF
technology. It can solve automatically problems and give human
readable solution agree with those writting by students and teachers.
Abstract: This paper is a numerical investigation of a laminar
isothermal plane two dimensional wall jet. Special attention has been
paid to the effect of the inlet conditions at the nozzle exit on the
hydrodynamic and thermal characteristics of the flow. The
behaviour of various fluids evolving in both forced and mixed
convection regimes near a vertical plate plane is carried out. The
system of governing equations is solved with an implicit finite
difference scheme. For numerical stability we use a staggered non
uniform grid. The obtained results show that the effect of the Prandtl
number is significant in the plume region in which the jet flow is
governed by buoyant forces. Further for ascending X values, the
buoyancy forces become dominating, and a certain agreement
between the temperature profiles are observed, which shows that the
velocity profile has no longer influence on the wall temperature
evolution in this region. Fluids with low Prandtl number warm up
more importantly, because for such fluids the effect of heat diffusion
is higher.
Abstract: Present wireless communication demands compact and intelligent devices with multitasking capabilities at affordable cost. The focus in the presented paper is on a dual band antenna for wireless communication with the capability of operating at two frequency bands with same structure. Two resonance frequencies are observed with the second operation band at 4.2GHz approximately three times the first resonance frequency at 1.5GHz. Structure is simple loop of microstrip line with characteristic impedance 50 ohms. The proposed antenna is designed using defective ground structure (DGS) and shows the nearly one third reductions in size as compared to without DGS. This antenna was simulated on electromagnetic (EM) simulation software and fabricated using microwave integrated circuit technique on RT-Duroid dielectric substrate (εr= 2.22) of thickness (H=15 mils). The designed antenna was tested on automatic network analyzer and shows the good agreement with simulated results. The proposed structure is modeled into an equivalent electrical circuit and simulated on circuit simulator. Subsequently, theoretical analysis was carried out and simulated. The simulated, measured, equivalent circuit response, and theoretical results shows good resemblance. The bands of operation draw many potential applications in today’s wireless communication.
Abstract: A gene network gives the knowledge of the regulatory
relationships among the genes. Each gene has its activators and
inhibitors that regulate its expression positively and negatively
respectively. Genes themselves are believed to act as activators and
inhibitors of other genes. They can even activate one set of genes and
inhibit another set. Identifying gene networks is one of the most
crucial and challenging problems in Bioinformatics. Most work done
so far either assumes that there is no time delay in gene regulation or
there is a constant time delay. We here propose a Dynamic Time-
Lagged Correlation Based Method (DTCBM) to learn the gene
networks, which uses time-lagged correlation to find the potential
gene interactions, and then uses a post-processing stage to remove
false gene interactions to common parents, and finally uses dynamic
correlation thresholds for each gene to construct the gene network.
DTCBM finds correlation between gene expression signals shifted in
time, and therefore takes into consideration the multi time delay
relationships among the genes. The implementation of our method is
done in MATLAB and experimental results on Saccharomyces
cerevisiae gene expression data and comparison with other methods
indicate that it has a better performance.
Abstract: In this paper, the two-dimension differential transformation method (DTM) is employed to obtain the closed form solutions of the three famous coupled partial differential equation with physical interest namely, the coupled Korteweg-de Vries(KdV) equations, the coupled Burgers equations and coupled nonlinear Schrödinger equation. We begin by showing that how the differential transformation method applies to a linear and non-linear part of any PDEs and apply on these coupled PDEs to illustrate the sufficiency of the method for this kind of nonlinear differential equations. The results obtained are in good agreement with the exact solution. These results show that the technique introduced here is accurate and easy to apply.
Abstract: Inconel 718, a nickel based super-alloy is an
extensively used alloy, accounting for about 50% by weight of
materials used in an aerospace engine, mainly in the gas turbine
compartment. This is owing to their outstanding strength and
oxidation resistance at elevated temperatures in excess of 5500 C.
Machining is a requisite operation in the aircraft industries for the
manufacture of the components especially for gas turbines. This
paper is concerned with optimization of the surface roughness when
turning Inconel 718 with cermet inserts. Optimization of turning
operation is very useful to reduce cost and time for machining. The
approach is based on Response Surface Method (RSM). In this work,
second-order quadratic models are developed for surface roughness,
considering the cutting speed, feed rate and depth of cut as the cutting
parameters, using central composite design. The developed models
are used to determine the optimum machining parameters. These
optimized machining parameters are validated experimentally, and it
is observed that the response values are in reasonable agreement with
the predicted values.