Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: This paper presents an investigation of the power
penalties imposed by four-wave mixing (FWM) on G.652 (Single-
Mode Fiber - SMF), G.653 (Dispersion-Shifted Fiber - DSF), and
G.655 (Non-Zero Dispersion-Shifted Fiber - NZDSF) compliant
fibers, considering the DWDM grids suggested by the ITU-T
Recommendations G.692, and G.694.1, with uniform channel
spacing of 100, 50, 25, and 12.5 GHz. The mathematical/numerical
model assumes undepleted pumping, and shows very clearly the
deleterious effect of FWM on the performance of DWDM systems,
measured by the signal-to-noise ratio (SNR). The results make it
evident that non-uniform channel spacing is practically mandatory
for WDM systems based on DSF fibers.
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.
Abstract: Two-dimensional Direct Numerical Simulation (DNS)
of high Schmidt number mass transfer in a convective flow environment
(Rayleigh-B'enard) is carried out and results are compared to
experimental data. A fourth-order accurate WENO-scheme has been
used for scalar transport in order to aim for a high accuracy in areas
of high concentration gradients. It was found that the typical spatial
distance between downward plumes of cold high concentration water
and the eddy size are in good agreement with experiments using a
combined PIV-LIF technique for simultaneous and spatially synoptic
measurements of 2D velocity and concentration fields.
Abstract: One important problem in today organizations is the
existence of non-integrated information systems, inconsistency and
lack of suitable correlations between legacy and modern systems.
One main solution is to transfer the local databases into a global one.
In this regards we need to extract the data structures from the legacy
systems and integrate them with the new technology systems. In
legacy systems, huge amounts of a data are stored in legacy
databases. They require particular attention since they need more
efforts to be normalized, reformatted and moved to the modern
database environments. Designing the new integrated (global)
database architecture and applying the reverse engineering requires
data normalization. This paper proposes the use of database reverse
engineering in order to integrate legacy and modern databases in
organizations. The suggested approach consists of methods and
techniques for generating data transformation rules needed for the
data structure normalization.
Abstract: This paper addresses issues of integral steering of
vehicles with two steering axles, where the rear wheels are pivoted in
the direction of the front wheels, but also in the opposite direction.
The steering box of the rear axle is presented with simple linkages
(single contour) that correlate the pivoting of the rear wheels
according to the direction of the front wheels, respectively to the
rotation angle of the steering wheel. The functionality of the system
is analyzed – the extent to which the requirements of the integral
steering are met by the considered/proposed mechanisms. The paper
highlights the quality of the single contour linkages, with two driving
elements for meeting these requirements, emphasizing diagrams of
mechanisms with 2 driving elements. Cam variants are analyzed and
proposed for the rear axle steering box. Cam profiles are determined
by various factors.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: Twist drills are geometrical complex tools and thus various researchers have adopted different mathematical and experimental approaches for their simulation. The present paper acknowledges the increasing use of modern CAD systems and using the API (Application Programming Interface) of a CAD system, drilling simulations are carried out. The developed DRILL3D software routine, creates parametrically controlled tool geometries and using different cutting conditions, achieves the generation of solid models for all the relevant data involved (drilling tool, cut workpiece, undeformed chip). The final data derived, consist a platform for further direct simulations regarding the determination of cutting forces, tool wear, drilling optimizations etc.
Abstract: A high performance computer includes a fast
processor and millions bytes of memory. During the data processing,
huge amount of information are shuffled between the memory and
processor. Because of its small size and its effectiveness speed, cache
has become a common feature of high performance computers.
Enhancing cache performance proved to be essential in the speed up
of cache-based computers. Most enhancement approaches can be
classified as either software based or hardware controlled. The
performance of the cache is quantified in terms of hit ratio or miss
ratio. In this paper, we are optimizing the cache performance based
on enhancing the cache hit ratio. The optimum cache performance is
obtained by focusing on the cache hardware modification in the way
to make a quick rejection to the missed line's tags from the hit-or
miss comparison stage, and thus a low hit time for the wanted line in
the cache is achieved. In the proposed technique which we called
Even- Odd Tabulation (EOT), the cache lines come from the main
memory into cache are classified in two types; even line's tags and
odd line's tags depending on their Least Significant Bit (LSB). This
division is exploited by EOT technique to reject the miss match line's
tags in very low time compared to the time spent by the main
comparator in the cache, giving an optimum hitting time for the
wanted cache line. The high performance of EOT technique against
the familiar mapping technique FAM is shown in the simulated
results.
Abstract: The purpose of this study was to study postpartum breastfeeding mothers to determine the impact their psychosocial and spiritual dimensions play in promoting full-term (6 month duration) breastfeeding of their infants. Purposive and snowball sampling methods were used to identify and recruit the study's participants. A total of 23 postpartum mothers, who were breastfeeding within 6 weeks after giving birth, participated in this study. In-depth interviews combined with observations, participant focus groups, and ethnographic records were used for data collection. The Data were then analyzed using content analysis and typology. The results of this study illustrated that postpartum mothers experienced fear and worry that they would lack support from their spouse, family and peers, and that their infant would not get enough milk It was found that the main barrier mothers faced in breastfeeding to full-term was the difficulty of continuing to breastfeed when returning to work. 81.82% of the primiparous mothers and 91.67% of the non-primiparous mothers were able to breastfeed for the desired full-term of 6 months. Factors found to be related to breastfeeding for six months included 1) belief and faith in breastfeeding, 2) support from spouse and family members, 3) counseling from public health nurses and friends. The sample also provided evidence that religious principles such as tolerance, effort, love, and compassion to their infant, and positive thinking, were used in solving their physical, mental and spiritual problems.
Abstract: The influence of axial magnetic field (B=0.48 T) on
the variation of ionization efficiency coefficient h and secondary
electron emission coefficient g with respect to reduced electric field
E/P is studied at a new range of plane-parallel electrode spacing (0<
d< 20 cm) and different nitrogen working pressure between 0.5-20
Pa. The axial magnetic field is produced from an inductive copper
coil of radius 5.6 cm. The experimental data of breakdown voltage is
adopted to estimate the mean Paschen curves at different working
features. The secondary electron emission coefficient is calculated
from the mean Paschen curve and used to determine the minimum
breakdown voltage. A reduction of discharge voltage of about 25% is
investigated by the applied of axial magnetic field. At high interelectrode
spacing, the effect of axial magnetic field becomes more
significant for the obtained values of h but it was less for the values
of g.
Abstract: The job shop scheduling problem (JSSP) is well known as one of the most difficult combinatorial optimization problems. This paper presents a hybrid genetic algorithm for the JSSP with the objective of minimizing makespan. The efficiency of the genetic algorithm is enhanced by integrating it with a local search method. The chromosome representation of the problem is based on operations. Schedules are constructed using a procedure that generates full active schedules. In each generation, a local search heuristic based on Nowicki and Smutnicki-s neighborhood is applied to improve the solutions. The approach is tested on a set of standard instances taken from the literature and compared with other approaches. The computation results validate the effectiveness of the proposed algorithm.
Abstract: In designing of condensers, the prediction of pressure
drop is as important as the prediction of heat transfer coefficient.
Modeling of two phase flow, particularly liquid – vapor flow under
diabatic conditions inside a horizontal tube using CFD analysis is
difficult with the available two phase models in FLUENT due to
continuously changing flow patterns. In the present analysis, CFD
analysis of two phase flow of refrigerants inside a horizontal tube of
inner diameter, 0.0085 m and 1.2 m length is carried out using
homogeneous model under adiabatic conditions. The refrigerants
considered are R22, R134a and R407C. The analysis is performed at
different saturation temperatures and at different flow rates to
evaluate the local frictional pressure drop. Using Homogeneous
model, average properties are obtained for each of the refrigerants
that is considered as single phase pseudo fluid. The so obtained
pressure drop data is compared with the separated flow models
available in literature.
Abstract: This paper presents the experimental results of a
single cylinder Enfield engine using an electronically controlled fuel
injection system which was developed to carry out exhaustive tests
using neat CNG, and mixtures of hydrogen in compressed natural gas
(HCNG) as 0, 5, 10, 15 and 20% by energy. Experiments were
performed at 2000 and 2400 rpm with wide open throttle and varying
the equivalence ratio. Hydrogen which has fast burning rate, when
added to compressed natural gas, enhances its flame propagation rate.
The emissions of HC, CO, decreased with increasing percentage of
hydrogen but NOx was found to increase. The results indicated a
marked improvement in the brake thermal efficiency with the
increase in percentage of hydrogen added. The improved thermal
efficiency was clearly observed to be more in lean region as
compared to rich region. This study is expected to reduce vehicular
emissions along with increase in thermal efficiency and thus help in
reduction of further environmental degradation.
Abstract: Graph based image segmentation techniques are
considered to be one of the most efficient segmentation techniques
which are mainly used as time & space efficient methods for real
time applications. How ever, there is need to focus on improving the
quality of segmented images obtained from the earlier graph based
methods. This paper proposes an improvement to the graph based
image segmentation methods already described in the literature. We
contribute to the existing method by proposing the use of a weighted
Euclidean distance to calculate the edge weight which is the key
element in building the graph. We also propose a slight modification
of the segmentation method already described in the literature, which
results in selection of more prominent edges in the graph. The
experimental results show the improvement in the segmentation
quality as compared to the methods that already exist, with a slight
compromise in efficiency.
Abstract: In this article we are going to discuss the improvement
of the multi classes- classification problem using multi layer
Perceptron. The considered approach consists in breaking down the
n-class problem into two-classes- subproblems. The training of each
two-class subproblem is made independently; as for the phase of test,
we are going to confront a vector that we want to classify to all two
classes- models, the elected class will be the strongest one that won-t
lose any competition with the other classes. Rates of recognition
gotten with the multi class-s approach by two-class-s decomposition
are clearly better that those gotten by the simple multi class-s
approach.
Abstract: Microcirculation is essential for the proper supply of
oxygen and nutritive substances to the biological tissue and the
removal of waste products of metabolism. The determination of
blood flow in the capillaries is therefore of great interest to clinicians.
A comparison has been carried out using the developed non-invasive,
non-contact and whole field laser speckle contrast imaging (LSCI)
based technique and as well as a commercially available laser
Doppler blood flowmeter (LDF) to evaluate blood flow at the finger
tip and elbow and is presented here. The LSCI technique gives more
quantitative information on the velocity of blood when compared to
the perfusion values obtained using the LDF. Measurement of blood
flow in capillaries can be of great interest to clinicians in the
diagnosis of vascular diseases of the upper extremities.
Abstract: Wavelet transform or wavelet analysis is a recently
developed mathematical tool in applied mathematics. In numerical
analysis, wavelets also serve as a Galerkin basis to solve partial
differential equations. Haar transform or Haar wavelet transform has
been used as a simplest and earliest example for orthonormal wavelet
transform. Since its popularity in wavelet analysis, there are several
definitions and various generalizations or algorithms for calculating
Haar transform. Fast Haar transform, FHT, is one of the algorithms
which can reduce the tedious calculation works in Haar transform. In
this paper, we present a modified fast and exact algorithm for FHT,
namely Modified Fast Haar Transform, MFHT. The algorithm or
procedure proposed allows certain calculation in the process
decomposition be ignored without affecting the results.
Abstract: Software effort estimation is the process of predicting
the most realistic use of effort required to develop or maintain
software based on incomplete, uncertain and/or noisy input. Effort
estimates may be used as input to project plans, iteration plans,
budgets. There are various models like Halstead, Walston-Felix,
Bailey-Basili, Doty and GA Based models which have already used
to estimate the software effort for projects. In this study Statistical
Models, Fuzzy-GA and Neuro-Fuzzy (NF) Inference Systems are
experimented to estimate the software effort for projects. The
performances of the developed models were tested on NASA
software project datasets and results are compared with the Halstead,
Walston-Felix, Bailey-Basili, Doty and Genetic Algorithm Based
models mentioned in the literature. The result shows that the NF
Model has the lowest MMRE and RMSE values. The NF Model
shows the best results as compared with the Fuzzy-GA based hybrid
Inference System and other existing Models that are being used for
the Effort Prediction with lowest MMRE and RMSE values.