Abstract: In order to apply partially filled steel grid composite deck as the horizontal supporting structure of various kinds of infrastructures, the variation of its flexural strength according to design parameters such as cross and longitudinal bars constituting the steel grid and the type of shear connection is evaluated and compared experimentally. The result shows that the design sensitivity of the deck to the spacing of the cross bars is insignificant in the case of structure with low risk of punching failure or without load distribution problem. By means of shear connection composed by transverse rebar and longitudinal bar without additional shear stud bolts, the complete interaction between steel grid and concrete slab is able to be achieved and the composite deck can develop its bending resistance capacity.
Abstract: It has been shown that a load discontinuity at the end of
an impulse will result in an extra impulse and hence an extra amplitude
distortion if a step-by-step integration method is employed to yield the
shock response. In order to overcome this difficulty, three remedies
are proposed to reduce the extra amplitude distortion. The first remedy
is to solve the momentum equation of motion instead of the force
equation of motion in the step-by-step solution of the shock response,
where an external momentum is used in the solution of the momentum
equation of motion. Since the external momentum is a resultant of the
time integration of external force, the problem of load discontinuity
will automatically disappear. The second remedy is to perform a single
small time step immediately upon termination of the applied impulse
while the other time steps can still be conducted by using the time step
determined from general considerations. This is because that the extra
impulse caused by a load discontinuity at the end of an impulse is
almost linearly proportional to the step size. Finally, the third remedy
is to use the average value of the two different values at the integration
point of the load discontinuity to replace the use of one of them for
loading input. The basic motivation of this remedy originates from the
concept of no loading input error associated with the integration point
of load discontinuity. The feasibility of the three remedies are
analytically explained and numerically illustrated.
Abstract: The aim of this study is to determine the basic information and communication technology (ICT) skills that may be needed by students studying in the 8th grade of the primary education in their cooperative project works implemented via the Internet. Within the scope of the study, the curriculum used for European Computer Driving License (ECDL) and the curriculum used in Turkey are also compared in terms of the ability to use ICT, which is aimed to be provided to the students. The research population of the study, during which the pre test – post test control group experimental model was used, consisted of 40 students from three different schools. In the first stage of the study, the skills that might be needed by students for their cooperative project works implemented via the Internet were determined through examination of the completed Comenious, e – twinning and WorldLinks projects. In the second stage of the study, the curriculums of the Turkish Ministry of National Education (MEB) and ECDL were evaluated by seven different teachers in line with these skills. Also in this study the ECDL and MEB curriculums were compared in terms of capability to provide the skills to implement cooperative projects via the Internet. In line with the findings of the study, the skills that might be needed by students to implement cooperative projects via the Internet were outlined, and existence of a significant difference was established in favor of the ECDL curriculum upon comparison of both curriculums in accordance with this outline (U = 50,500; p
Abstract: Persian (Farsi) script is totally cursive and each character is written in several different forms depending on its former and later characters in the word. These complexities make automatic handwriting recognition of Persian a very hard problem and there are few contributions trying to work it out. This paper presents a novel practical approach to online recognition of Persian handwriting which is based on representation of inputs and patterns with very simple visual features and comparison of these simple terms. This recognition approach is tested over a set of Persian words and the results have been quite acceptable when the possible words where unknown and they were almost all correct in cases that the words where chosen from a prespecified list.
Abstract: CO2 miscible displacement is not feasible in many oil fields due to high reservoir temperature as higher pressure is required to achieve miscibility. The miscibility pressure is far higher than the formation fracture pressure making it impossible to have CO2 miscible displacement. However, by using oleophilic chemicals, minimum miscibility pressure (MMP) could be lowered. The main objective of this research is to find the best oleophilic chemical in MMP reduction using slim-tube test and Vanishing Interfacial Tension (VIT) The chemicals are selected based on the characteristics that it must be oil soluble, low water solubility, have 4 – 8 carbons, semi polar, economical, and safe for human operation. The families of chemicals chosen are carboxylic acid, alcohol, and ketone. The whole experiment would be conducted at 100°C and the best chemical is said to be effective when it is able to lower CO2-crude oil MMP the most. Findings of this research would have great impact to the oil and gas industry in reduction of operation cost for CO2EOR which is applicable to both onshore and offshore operation.
Abstract: Recently, genetic algorithms (GA) and particle swarm optimization (PSO) technique have attracted considerable attention among various modern heuristic optimization techniques. Since the two approaches are supposed to find a solution to a given objective function but employ different strategies and computational effort, it is appropriate to compare their performance. This paper presents the application and performance comparison of PSO and GA optimization techniques, for Thyristor Controlled Series Compensator (TCSC)-based controller design. The design objective is to enhance the power system stability. The design problem of the FACTS-based controller is formulated as an optimization problem and both the PSO and GA optimization techniques are employed to search for optimal controller parameters. The performance of both optimization techniques in terms of computational time and convergence rate is compared. Further, the optimized controllers are tested on a weakly connected power system subjected to different disturbances, and their performance is compared with the conventional power system stabilizer (CPSS). The eigenvalue analysis and non-linear simulation results are presented and compared to show the effectiveness of both the techniques in designing a TCSC-based controller, to enhance power system stability.
Abstract: This study employs auto-regressive distributed lag (ARDL) bounds approach to cointegration for long run and errorcorrection modeling (ECM) for short run analysis to examine the relationship between revenue gap and economic growth for Pakistan using annual time series data over the period 1980 to 2008. The short and long run results indicate that revenue gap is statistical significant and negatively effect economic growth. The significant and negative coefficient of error correction term in ECM indicates that after a shock, the long rum equilibrium will again converge towards equilibrium about 10.406 percent within a year.
Abstract: Wind is among the potential energy resources which
can be harnessed to generate wind energy for conversion into
electrical power. Due to the variability of wind speed with time and
height, it becomes difficult to predict the generated wind energy more
optimally. In this paper, an attempt is made to establish a
probabilistic model fitting the wind speed data recorded at
Makambako site in Tanzania. Wind speeds and direction were
respectively measured using anemometer (type AN1) and wind Vane
(type WD1) both supplied by Delta-T-Devices at a measurement
height of 2 m. Wind speeds were then extrapolated for the height of
10 m using power law equation with an exponent of 0.47. Data were
analysed using MINITAB statistical software to show the variability
of wind speeds with time and height, and to determine the underlying
probability model of the extrapolated wind speed data. The results
show that wind speeds at Makambako site vary cyclically over time;
and they conform to the Weibull probability distribution. From these
results, Weibull probability density function can be used to predict
the wind energy.
Abstract: The purpose of this study was to investigate the effects of computer–based instructional designs, namely modality and redundancy principles on the attitude and learning of music theory among primary pupils of different Music Intelligence levels. The lesson of music theory was developed in three different modes, audio and image (AI), text with image (TI) and audio with image and text (AIT). The independent variables were the three modes of courseware. The moderator variable was music intelligence. The dependent variables were the post test score. ANOVA was used to determine the significant differences of the pretest scores among the three groups. Analyses of covariance (ANCOVA) and Post hoc were carried out to examine the main effects as well as the interaction effects of the independent variables on the dependent variables. High music intelligence pupils performed significantly better than low music intelligence pupils in all the three treatment modes. The AI mode was found to help pupils with low music intelligence significantly more than the TI and AIT modes.
Abstract: In this paper, a new face recognition method based on
PCA (principal Component Analysis), LDA (Linear Discriminant
Analysis) and neural networks is proposed. This method consists of
four steps: i) Preprocessing, ii) Dimension reduction using PCA, iii)
feature extraction using LDA and iv) classification using neural
network. Combination of PCA and LDA is used for improving the
capability of LDA when a few samples of images are available and
neural classifier is used to reduce number misclassification caused by
not-linearly separable classes. The proposed method was tested on
Yale face database. Experimental results on this database
demonstrated the effectiveness of the proposed method for face
recognition with less misclassification in comparison with previous
methods.
Abstract: In the Fe-3%Si sheets, grade Hi-B, with AlN and MnS
as inhibitors, the Goss grains which abnormally grow do not have a
size greater than the average size of the primary matrix. In this
heterogeneous microstructure, the size factor is not a required
condition for the secondary recrystallization. The onset of the small
Goss grain abnormal growth appears to be related to a particular
behavior of their grain boundaries, to the local texture and to the
distribution of the inhibitors. The presence and the evolution of
oriented clusters ensure to the small Goss grains a favorable
neighborhood to grow. The modified Monte-Carlo approach, which
is applied, considers the local environment of each grain. The grain
growth is dependent of its real spatial position; the matrix
heterogeneity is then taken into account. The grain growth conditions
are considered in the global matrix and in different matrixes
corresponding to A component clusters. The grain growth behaviour
is considered with introduction of energy only, energy and mobility,
energy and mobility and precipitates.
Abstract: A new multi-step comprehensive experience-based
learning program was developed and carried out so that the students
understood about what was the principle of the circuit function and
how the designed circuit was used in actual advanced applications.
Abstract: Carbon Capture & Storage (CCS) is one of the various
methods that can be used to reduce the carbon footprint of the
energy sector. This paper focuses on the absorption of CO2 from
flue gas using packed columns, whose efficiency is highly dependent
on the structure of the liquid films within the column. To study the
characteristics of liquid films a CFD solver, OpenFOAM is utilised
to solve two-phase, isothermal film flow using the volume-of-fluid
(VOF) method. The model was validated using existing experimental
data and the Nusselt theory. It was found that smaller plate inclination
angles, with respect to the horizontal plane, resulted in larger wetted
areas on smooth plates. However, only a slight improvement in
the wetted area was observed. Simulations were also performed
using a ridged plate and it was observed that these surface textures
significantly increase the wetted area of the plate. This was mainly
attributed to the channelling effect of the ridges, which helped to
oppose the surface tension forces trying to minimise the surface area.
Rivulet formations on the ridged plate were also flattened out and
spread across a larger proportion of the plate width.
Abstract: Linear two-point boundary value problems of order
two are solved using cubic trigonometric B-spline interpolation
method (CTBIM). Cubic trigonometric B-spline is a piecewise
function consisting of trigonometric equations. This method is tested
on some problems and the results are compared with cubic B-spline
interpolation method (CBIM) from the literature. CTBIM is found to
approximate the solution slightly more accurately than CBIM if the
problems are trigonometric.
Abstract: In this paper, a bond graph dynamic model for a valvecontrolled
hydraulic cylinder has been developed. A simplified bond
graph model of the inter-actuator interactions in a multi-cylinder
hydraulic system has also been presented. The overall bond graph
model of a valve-controlled hydraulic cylinder was developed by
combining the bond graph sub-models of the pump, spool valve and
the actuator using junction structures. Causality was then assigned
in order to obtain a computational model which could be simulated.
The causal bond graph model of the hydraulic cylinder was verified
by comparing the open loop state responses to those of an ODE
model which had been developed in literature based on the same
assumptions. The results were found to correlate very well both
in the shape of the curves, magnitude and the response times,
thus indicating that the developed model represents the hydraulic
dynamics of a valve-controlled cylinder. A simplified model for interactuator
interaction was presented by connecting an effort source with
constant pump pressure to the zero-junction from which the cylinders
in a multi-cylinder system are supplied with a constant pressure from
the pump. On simulating the state responses of the developed model
under different situations of cylinder operations, indicated that such
a simple model can be used to predict the inter-actuator interactions.
Abstract: This study explored the relationship between
psychological traits, demographics and financial behavioral biases for
individual investors in Taiwan stock market. By using questionnaire
survey method conducted in 2010, there are 554 valid convenient
samples collected to examine the determinants of three types of
behavioral biases. Based on literature review, two hypothesized
models are constructed and further used to evaluate the effects of big
five personality traits and demographic variables on investment biases
through Structural Equation Model (SEM) analysis. The results
showed that investment biases of individual investors are significantly
related to four personality traits as well as some demographics.
Abstract: Transient eddy current problem is solved in the
present paper by the method of the Laplace transform for the case of
a double conductor line located parallel to a conducting half-space.
The Fourier sine and cosine integral transforms are used in order to
find the Laplace transform of the solution. The inverse Laplace
transform of the solution is found in closed form. The integrated
electromotive force per unit length of the double conductor line is
calculated in the form of an improper integral.
Abstract: Camera calibration is an important step in 3D
reconstruction. Camera calibration may be classified into two major types: traditional calibration and self-calibration. However, a calibration method in using a checkerboard is intermediate between traditional calibration and self-calibration. A self
is proposed based on a square in this paper. Only a square in the planar
template, the camera self-calibration can be completed through the single view. The proposed algorithm is that the virtual circle and straight line are established by a square on planar template, and
circular points, vanishing points in straight lines and the relation
between them are be used, in order to obtain the image of the absolute
conic (IAC) and establish the camera intrinsic parameters. To make
the calibration template is simpler, as compared with the Zhang Zhengyou-s method. Through real experiments and experiments, the experimental results show that this algorithm is
feasible and available, and has a certain precision and robustness.
Abstract: In this paper, we define distance partition of vertex set of a graph G with reference to a vertex in it and with the help of the same, a graph with metric dimension two (i.e. β (G) = 2 ) is characterized. In the process, we develop a polynomial time algorithm that verifies if the metric dimension of a given graph G is two. The same algorithm explores all metric bases of graph G whenever β (G) = 2 . We also find a bound for cardinality of any distance partite set with reference to a given vertex, when ever β (G) = 2 . Also, in a graph G with β (G) = 2 , a bound for cardinality of any distance partite set as well as a bound for number of vertices in any sub graph H of G is obtained in terms of diam H .
Abstract: Extraction of Fe(III) from aqueous solution using Trin-
butyl Phosphate (TBP) as carrier needs a highly acidic medium
(>6N) as it favours formation of chelating complex FeCl3.TBP.
Similarly, stripping of Iron(III) from loaded organic solvents requires
neutral pH or alkaline medium to dissociate the same complex. It is
observed that TBP co-extracts acids along with metal, which causes
reversal of driving force of extraction and iron(III) is re-extracted
back from the strip phase into the feed phase during Liquid Emulsion
Membrane (LEM) pertraction. Therefore, rate of extraction of
different mineral acids (HCl, HNO3, H2SO4) using TBP with and
without presence of metal Fe(III) was examined. It is revealed that in
presence of metal acid extraction is enhanced. Determination of mass
transfer coefficient of both acid and metal extraction was performed
by using Bulk Liquid Membrane (BLM). The average mass transfer
coefficient was obtained by fitting the derived model equation with
experimentally obtained data. The mass transfer coefficient of the
mineral acid extraction is in the order of kHNO3 = 3.3x10-6m/s > kHCl =
6.05x10-7m/s > kH2SO4 = 1.85x10-7m/s. The distribution equilibria of
the above mentioned acids between aqueous feed solution and a
solution of tri-n-butyl-phosphate (TBP) in organic solvents have been
investigated. The stoichiometry of acid extraction reveals the
formation of TBP.2HCl, HNO3.2TBP, and TBP.H2SO4 complexes.
Moreover, extraction of Iron(III) by TBP in HCl aqueous solution
forms complex FeCl3.TBP.2HCl while in HNO3 medium forms
complex 3FeCl3.TBP.2HNO3