Abstract: This paper presents the experimental results on effect of applied voltage stress frequency to the occurrence of electrical treeing in 22 kV cross linked polyethylene (XLPE) insulated cable.Hallow disk of XLPE insulating material with thickness 5 mm taken from unused high voltage cable was used as the specimen in this study. Stainless steel needle was inserted gradually into the specimen to give a tip to earth plane electrode separation of 2.50.2 mm at elevated temperature 105-110°C. The specimen was then annealed for 5 minute to minimize any mechanical stress build up around the needle-plane region before it was cooled down to room temperature. Each specimen were subjected to the same applied voltage stress level at 8 kV AC rms, with various frequency, 50, 100, 500, 1000 and 2000 Hz. Initiation time, propagation speed and pattern of electrical treeing were examined in order to study the effect of applied voltage stress frequency. By the experimental results, initial time of visible treeing decreases with increasing in applied voltage frequency. Also, obviously, propagation speed of electrical treeing increases with increasing in applied voltage frequency.Furthermore, two types of electrical treeing, bush-like and branch-like treeing were observed.The experimental results confirmed the effect of voltage stress frequency as well.
Abstract: This paper reports on the theoretical performance
analysis of the 1.3 μm In0.42Ga0.58As /In0.26Ga0.74As multiple quantum
well (MQW) vertical cavity surface emitting laser (VCSEL) on the
ternary In0.31Ga0.69As substrate. The output power of 2.2 mW has
been obtained at room temperature for 7.5 mA injection current. The
material gain has been estimated to be ~3156 cm-1 at room
temperature with the injection carrier concentration of 2×1017 cm-3.
The modulation bandwidth of this laser is measured to be 9.34 GHz
at room temperature for the biasing current of 2 mA above the
threshold value. The outcomes reveal that the proposed InGaAsbased
MQW laser is the promising one for optical communication
system.
Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: This paper presents features that characterize power
quality disturbances from recorded voltage waveforms using wavelet
transform. The discrete wavelet transform has been used to detect
and analyze power quality disturbances. The disturbances of interest
include sag, swell, outage and transient. A power system network has
been simulated by Electromagnetic Transients Program. Voltage
waveforms at strategic points have been obtained for analysis, which
includes different power quality disturbances. Then wavelet has been
chosen to perform feature extraction. The outputs of the feature
extraction are the wavelet coefficients representing the power quality
disturbance signal. Wavelet coefficients at different levels reveal the
time localizing information about the variation of the signal.
Abstract: We consider a two-way relay network where two sources exchange information. A relay helps the two sources exchange information using the decode-and-XOR-forward protocol. We investigate the power minimization problem with minimum rate constraints. The system needs two time slots and in each time slot the required rate pair should be achievable. The power consumption is minimized in each time slot and we obtained the closed form solution. The simulation results confirm that the proposed power allocation scheme consumes lower total power than the conventional schemes.
Abstract: A systematic way to derive the conserved quantities for the axisymmetric liquid jet, free jet and wall jet using conservation laws is presented. The flow in axisymmetric jets is governed by Prandtl-s momentum boundary layer equation and the continuity equation. The multiplier approach is used to construct a basis of conserved vectors for the system of two partial differential equations for the two velocity components. The basis consists of two conserved vectors. By integrating the corresponding conservation laws across the jet and imposing the boundary conditions, conserved quantities are derived for the axisymmetric liquid and free jet. The multiplier approach applied to the third-order partial differential equation for the stream function yields two local conserved vectors one of which is a non-local conserved vector for the system. One of the conserved vectors gives the conserved quantity for the axisymmetric free jet but the conserved quantity for the wall jet is not obtained from the second conserved vector. The conserved quantity for the axisymmetric wall jet is derived from a non-local conserved vector of the third-order partial differential equation for the stream function. This non-local conserved vector for the third-order partial differential equation for the stream function is obtained by using the stream function as multiplier.
Abstract: Formative usability evaluation aims at finding
usability problems during the development process. The earlier these
problems are identified, the less expensive to fix they are. This paper
presents some preliminary results from a formative usability testing
of the 1st prototype developed for the ARiSE (Augmented Reality in
School Environments) project.
Abstract: This paper presented a MATLAB-based system named Smart Access Network Testing, Analyzing and Database (SANTAD), purposely for in-service transmission surveillance and self restoration against fiber fault in fiber-to-the-home (FTTH) access network. The developed program will be installed with optical line terminal (OLT) at central office (CO) to monitor the status and detect any fiber fault that occurs in FTTH downwardly from CO towards residential customer locations. SANTAD is interfaced with optical time domain reflectometer (OTDR) to accumulate every network testing result to be displayed on a single computer screen for further analysis. This program will identify and present the parameters of each optical fiber line such as the line's status either in working or nonworking condition, magnitude of decreasing at each point, failure location, and other details as shown in the OTDR's screen. The failure status will be delivered to field engineers for promptly actions, meanwhile the failure line will be diverted to protection line to ensure the traffic flow continuously. This approach has a bright prospect to improve the survivability and reliability as well as increase the efficiency and monitoring capabilities in FTTH.
Abstract: Solar energy has a major role in renewable energy
resources. Solar Cell as a basement of solar system has attracted lots
of research. To conduct a study about solar energy system, an
authenticated model is required. Diode base PV models are widely
used by researchers. These models are classified based on the number
of diodes used in them. Single and two-diode models are well
studied. Single-diode models may have two, three or four elements.
In this study, these solar cell models are examined and the simulation
results are compared to each other. All PV models are re-designed in
the Matlab/Simulink software and they examined by certain test
conditions and parameters. This paper provides comparative studies
of these models and it tries to compare the simulation results with
manufacturer-s data sheet to investigate model validity and accuracy.
The results show a four- element single-diode model is accurate and
has moderate complexity in contrast to the two-diode model with
higher complexity and accuracy
Abstract: In this paper, a heuristic method for simultaneous
rescue robot path-planning and mission scheduling is introduced
based on project management techniques, multi criteria decision
making and artificial potential fields path-planning. Groups of
injured people are trapped in a disastrous situation. These people are
categorized into several groups based on the severity of their
situation. A rescue robot, whose ultimate objective is reaching
injured groups and providing preliminary aid for them through a path
with minimum risk, has to perform certain tasks on its way towards
targets before the arrival of rescue team. A decision value is assigned
to each target based on the whole degree of satisfaction of the criteria
and duties of the robot toward the target and the importance of
rescuing each target based on their category and the number of
injured people. The resulted decision value defines the strength of the
attractive potential field of each target. Dangerous environmental
parameters are defined as obstacles whose risk determines the
strength of the repulsive potential field of each obstacle. Moreover,
negative and positive energies are assigned to the targets and
obstacles, which are variable with respects to the factors involved.
The simulation results show that the generated path for two cases
studies with certain differences in environmental conditions and
other risk factors differ considerably.
Abstract: In this paper, a novel wave equation for electromagnetic
waves in a medium having anisotropic permittivity has been derived
with the help of Maxwell-s curl equations. The x and y components
of the Maxwell-s equations are written with the permittivity () being
a 3 × 3 symmetric matrix. These equations are solved for Ex , Ey,
Hx, Hy in terms of Ez, Hz, and the partial derivatives. The Z
components of the Maxwell-s curl are then used to arrive to the
generalized Helmholtz equations for Ez and Hz.
Abstract: Educational institutions increasingly adopt the
students-as-customers concept to satisfy their students.
Understanding students- perspectives on the use of this business
concept in educational institutions is necessary for the institutions to
effectively align these perspectives with their management practice.
The study investigates whether students in technology and business
disciplines have significantly different attitudes toward using the
students-as-customers concept in educational institutions and
explores the impact of treating students as customers in technology
disciplines under students- perspectives. The results from
quantitative and qualitative data analyses show that technology
students, in contrast to business students, fairly disagree with
educational institutions to treat students as customers. Treating
students as customers in technology disciplines will have a negative
influence on teaching performance, instructor-student relationships
and educational institutions- aim, but a positive influence on service
quality in educational institutions. The paper discusses the findings
and concludes with implications and limitations of the study.
Abstract: This paper addresses the stabilization issues for a class of uncertain switched neutral systems with nonlinear perturbations. Based on new classes of piecewise Lyapunov functionals, the stability assumption on all the main operators or the convex combination of coefficient matrices is avoid, and a new switching rule is introduced to stabilize the neutral systems. The switching rule is designed from the solution of the so-called Lyapunov-Metzler linear matrix inequalities. Finally, three simulation examples are given to demonstrate the significant improvements over the existing results.
Abstract: Currently WWW is the first solution for scholars in
finding information. But, analyzing and interpreting this volume of
information will lead to researchers overload in pursuing their
research.
Trend detection in scientific publication retrieval systems helps
scholars to find relevant, new and popular special areas by
visualizing the trend of input topic.
However, there are few researches on trend detection in scientific
corpora while their proposed models do not appear to be suitable.
Previous works lack of an appropriate representation scheme for
research topics.
This paper describes a method that combines Semantic Web and
ontology to support advance search functions such as trend detection
in the context of scholarly Semantic Web system (SSWeb).
Abstract: The main objectives of this study are to inspect and
identify any damage of jaimusi highway prestressed concrete bridge
after repair and strengthening of damaged structural members and to
evaluate the performance of the bridge structural members by
adopting static load test. Inspection program after repair and
strengthening includes identifying and evaluating the structural
members of bridge such as T-shape cantilever structure, hanging
beams, corbels, external tendons, anchor beams, sticking steel plate,
and piers. The results of inspection show that the overall state of the
bridge structural member after repair and strengthening is good. The
results of rebound test of concrete strength show that the average
strength of concrete is 46.31Mpa. Whereas, the average value of
concrete strength of anchor beam is 49.82Mpa. According to the
results of static load test, the experimental values are less than
theoretical values of internal forces, deflection, and strain, indicating
that the stiffness of the experimental structure, overall deformation
and integrity satisfy the designed standard and the working
performance is good, and the undertaking capacity has a certain
surplus. There is not visible change in the length and width of cracks
and there are not new cracks under experimental load.
Abstract: This paper focuses on creating a component model of information system under uncertainty. The paper identifies problem in current approach of component modeling and proposes fuzzy tool, which will work with vague customer requirements and propose components of the resulting component model. The proposed tool is verified on specific information system and results are shown in paper. After finding suitable sub-components of the resulting component model, the component model is visualised by tool.
Abstract: Environment today is featured with aging population,
increasing prevalence of chronic disease and complex of medical
treatment. Safe use of pharmaceutics relied very much on the efforts
made by both the health- related organizations and as well as the
government agencies. As far as the specialization concern in providing
health services to the patients, the government actively issued and
implemented the divisions of medical treatment and pharmaceutical to
improve the quality of care and to reduce medication errors and ensure
public health. Pharmaceutical sub-sector policy has been implemented
for 13 years. This study attempts to explore the factors that affect the
patients- behavior intention of refilling a prescription from a NHIB
pharmacy. Samples were those patients refilling their prescriptions
with the case NHIB pharmacies. A self-administered questionnaire
was used to collect respondents- information while the patients or
family members visit the pharmacy for the refilling. 1,200
questionnaires were dispatched in 37 pharmacies that randomly
selected from Pingtung City, Dongkang, Chaozhou, Hengchun areas.
732 responses were gained with 604 valid samples for further analyses.
Results of data analyses indicated that respondents- attitude,
subjective norm, perceived behavior control and behavior intentions
toward refilling behavior varied from some demographic variables to
another. This research also suggested adding actual behavior, either by
a self-report or observed, into the research.
Abstract: Privacy issues commonly discussed among
researchers, practitioners, and end-users in pervasive healthcare.
Pervasive healthcare systems are applications that can support
patient-s need anytime and anywhere. However, pervasive healthcare
raises privacy concerns since it can lead to situations where patients
may not be aware that their private information is being shared and
becomes vulnerable to threat. We have systematically analyzed the
privacy issues and present a summary in tabular form to show the
relationship among the issues. The six issues identified are medical
information misuse, prescription leakage, medical information
eavesdropping, social implications for the patient, patient difficulties
in managing privacy settings, and lack of support in designing
privacy-sensitive applications. We narrow down the issues and chose
to focus on the issue of 'lack of support in designing privacysensitive
applications' by proposing a privacy-sensitive architecture
specifically designed for pervasive healthcare monitoring systems.
Abstract: Yam starch obtained from the water yam (munlued)
by the wet milling process was studied for some physicochemical
properties. Yam starch film was prepared by casting using glycerol as
a plasticizer. The effect of different glycerol (1.30, 1.65 and
2.00g/100g of filmogenic solution) and starch concentrations (3.30,
3.65 and 4.00g /100g of filmogenic solution) were evaluated on some
characteristics of the film. The temperature for obtaining the
gelatinized starch solution was 70-80°C and then dried at 45°C for 4
hours. The resulting starch from munlued granular morphology was
triangular and the average size of the granule was 26.68 μm. The
amylose content by colorimetric method was 26 % and the gelatinize
temperature was 70-80°C. The appearance of the film was smooth,
transparent, and glossy with average moisture content of 25.96% and
thickness of 0.01mm. Puncture deformation and flexibility increased
with glycerol content. The starch and glycerol concentration were a
significant factor of the yam starch film characteristics. Yam starch
film can be described as a biofilm providing many applications and
developments with the advantage of biodegradability.
Abstract: The protein domain structure has been widely used as the most informative sequence feature to computationally predict protein-protein interactions. However, in a recent study, a research group has reported a very high accuracy of 94% using hydrophobicity feature. Therefore, in this study we compare and verify the usefulness of protein domain structure and hydrophobicity properties as the sequence features. Using the Support Vector Machines (SVM) as the learning system, our results indicate that both features achieved accuracy of nearly 80%. Furthermore, domains structure had receiver operating characteristic (ROC) score of 0.8480 with running time of 34 seconds, while hydrophobicity had ROC score of 0.8159 with running time of 20,571 seconds (5.7 hours). These results indicate that protein-protein interaction can be predicted from domain structure with reliable accuracy and acceptable running time.