Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.
Abstract: With the advancement of wireless sensor network technology,
its practical utilization is becoming an important challange.
This paper overviews my past environmental monitoring project,
and discusses the process of starting the monitoring by classifying
it into four steps. The steps to start environmental monitoring can
be complicated, but not well discussed by researchers of wireless
sensor network technology. This paper demonstrates our activity and
challenges in each of the four steps to ease the process, and argues
future challenges to enable quick start of environmental monitoring.
Abstract: In this paper, we evaluate the performance of the
Hybrid-MIMO Receiver Scheme (HMRS) in Cognitive Radio
network (CR-network). We investigate the efficiency of the proposed
scheme which the energy level and user number of primary user are
varied according to the characteristic of CR-network. HMRS can
allow users to transmit either Space-Time Block Code (STBC) or
Spatial-Multiplexing (SM) streams simultaneously by using
Successive Interference Cancellation (SIC) and Maximum Likelihood
Detection (MLD). From simulation, the results indicate that the
interference level effects to the performance of HMRS. Moreover,
the exact closed-form capacity of the proposed scheme is derived and
compared with STBC scheme.
Abstract: The present study addresses problems and solutions
related to new functional food production. Wheat (Triticum aestivum
L) bran obtained from industrial mill company “Dobeles
dzirnavieks”, was used to investigate them as raw material like
nutrients for Bifidobacterium lactis Bb-12. Enzymatic hydrolysis of
wheat bran starch was carried out by α-amylase from Bacillus
amyloliquefaciens (Sigma Aldrich). The Viscozyme L purchased
from (Sigma Aldrich) were used for reducing released sugar.
Bifidibacterium lactis Bb-12 purchased from (Probio-Tec® CHR
Hansen) was cultivated in enzymatically hydrolysed wheat bran
mash. All procedures ensured the number of active Bifidobacterium
lactis Bb-12 in the final product reached 105 CFUg-1. After enzymatic
and bacterial fermentations sample were freeze dried for analysis of
chemical compounds. All experiments were performed at Faculty of
Food Technology of Latvia University of Agriculture in January-
March 2013. The obtained results show that both types of wheat bran
(enzymatically treated and non-treated) influenced the fermentative
activity and number of Bifidibacterium lactis Bb-12 viable in wheat
bran mash. Amount of acidity strongly increase during the wheat
bran mash fermentation. The main objective of this work was to
create low-energy functional enzymatically and bacterially treated
food from wheat bran using enzymatic hydrolysis of carbohydrates
and following cultivation of Bifidobacterium lactis Bb-12.
Abstract: Factoring Boolean functions is one of the basic operations in algorithmic logic synthesis. A novel algebraic factorization heuristic for single-output combinatorial logic functions is presented in this paper and is developed based on the set theory paradigm. The impact of factoring is analyzed mainly from a low power design perspective for standard cell based digital designs in this paper. The physical implementation of a number of MCNC/IWLS combinational benchmark functions and sub-functions are compared before and after factoring, based on a simple technology mapping procedure utilizing only standard gate primitives (readily available as standard cells in a technology library) and not cells corresponding to optimized complex logic. The power results were obtained at the gate-level by means of an industry-standard power analysis tool from Synopsys, targeting a 130nm (0.13μm) UMC CMOS library, for the typical case. The wire-loads were inserted automatically and the simulations were performed with maximum input activity. The gate-level simulations demonstrate the advantage of the proposed factoring technique in comparison with other existing methods from a low power perspective, for arbitrary examples. Though the benchmarks experimentation reports mixed results, the mean savings in total power and dynamic power for the factored solution over a non-factored solution were 6.11% and 5.85% respectively. In terms of leakage power, the average savings for the factored forms was significant to the tune of 23.48%. The factored solution is expected to better its non-factored counterpart in terms of the power-delay product as it is well-known that factoring, in general, yields a delay-efficient multi-level solution.
Abstract: In this study, numerical simulations on laminar flow in
sinusoidal wavy shaped tubes were conducted for mean Reynolds
number of 250, which is in the range of physiological flow-rate and
investigated flow structures, pressure distribution and particle
trajectories both in steady and periodic inflow conditions. For
extensive comparisons, various wave lengths and amplitudes of sine
function for geometry of tube models were employed. The results
showed that small amplitude secondary curvature has significant
influence on the nature of flow patterns and particle mixing
mechanism. This implies that characterizing accurate geometry is
essential in accurate predicting of in vivo hemodynamics and may
motivate further study on any possibility of reflection of secondary
flow on vascular remodeling and pathophysiology.
Abstract: In this paper, we propose a robust disease detection
method, called adaptive orientation code matching (Adaptive OCM),
which is developed from a robust image registration algorithm:
orientation code matching (OCM), to achieve continuous and
site-specific detection of changes in plant disease. We use two-stage
framework for realizing our research purpose; in the first stage,
adaptive OCM was employed which could not only realize the
continuous and site-specific observation of disease development, but
also shows its excellent robustness for non-rigid plant object searching
in scene illumination, translation, small rotation and occlusion changes
and then in the second stage, a machine learning method of support
vector machine (SVM) based on a feature of two dimensional (2D)
xy-color histogram is further utilized for pixel-wise disease
classification and quantification. The indoor experiment results
demonstrate the feasibility and potential of our proposed algorithm,
which could be implemented in real field situation for better
observation of plant disease development.
Abstract: This article analyses conspiracy theories as part of the
wider discourses of missionary politics. It presents a case study of
Venezuela and describes how its leaders use conspiracy theories as
political tools. Through quotes taken form Venezuelan president
Chavez-s public speeches and other sources, and through a short
analysis of the ideological basis of his discourses, it shows how
conspiracy theories are constructed and how they affect the local
political praxis. The article also describes how conspiracy theories
have been consistently used as an important part of the construction of
a political religion for the New Man of the Bolivarian Revolution. It
concludes that the use of conspiracy theories by political leaders
produces a sense of loss of political agency.
Abstract: The study of the fouling deposition of pink guava
juice (PGJ) is relatively new research compared to milk fouling
deposit. In this work, a new experimental set-up was developed to
imitate the fouling formation in heat exchanger, namely a continuous
flow experimental set-up heat exchanger. The new experimental setup
was operated under industrial pasteurization temperature of PGJ,
which was at 93°C. While the flow rate and pasteurization period
were based on the experimental capacity, which were 0.5 and 1
liter/min for the flow rate and the pasteurization period was set for 1
hour. Characterization of the fouling deposit was determined by
using various methods. Microstructure of the deposits was carried
out using ESEM. Proximate analyses were performed to determine
the composition of moisture, fat, protein, fiber, ash and carbohydrate
content. A study on the hardness and stickiness of the fouling deposit
was done using a texture analyzer. The presence of seedstone in pink
guava juice was also analyzed using a particle analyzer. The findings
shown that seedstone from pink guava juice ranging from 168 to
200μm and carbohydrate was found to be a major composition
(47.7% of fouling deposit consists of carbohydrate). Comparison
between the hardness and stickiness of the deposits at two different
flow rates showed that fouling deposits were harder and denser at
higher flow rate. Findings from this work provide basis knowledge
for further study on fouling and cleaning of PGJ.
Abstract: This paper discusses the utilization of marine biomass as an energy resource in Japan. A marine biomass energy system in Japan was proposed consisting of seaweed cultivation (Laminaria japonica) at offshore marine farms, biogas production via methane fermentation of the seaweeds, and fuel cell power generation driven by the generated biogas. We estimated energy output, energy supply potential, and CO2 mitigation in Japan on the basis of the proposed system. As a result, annual energy production was estimated to be 1.02-109 kWh/yr at nine available sites. Total CO2 mitigation was estimated to be 1.04-106 tonnes per annum at the nine sites. However, the CO2 emission for the construction of relevant facilities is not taken into account in this paper. The estimated CO2 mitigation is equivalent to about 0.9% of the required CO2 mitigation for Japan per annum under the Kyoto Protocol framework.
Abstract: In recent methodological articles related to structural equation modeling (SEM), the question of how to measure endogenous formative variables has been raised as an urgent, unresolved issue. This research presents an empirical application from the CRM system development context to test a recently developed technique, which makes it possible to measure endogenous formative constructs in structural models. PLS path modeling is used to demonstrate the feasibility of measuring antecedent relationships at the formative indicator level, not the formative construct level. Empirical results show that this technique is a promising approach to measure antecedent relationships of formative constructs in SEM.
Abstract: Motion detection is very important in image
processing. One way of detecting motion is using optical flow.
Optical flow cannot be computed locally, since only one independent
measurement is available from the image sequence at a point, while
the flow velocity has two components. A second constraint is needed.
The method used for finding the optical flow in this project is
assuming that the apparent velocity of the brightness pattern varies
smoothly almost everywhere in the image. This technique is later
used in developing software for motion detection which has the
capability to carry out four types of motion detection. The motion
detection software presented in this project also can highlight motion
region, count motion level as well as counting object numbers. Many
objects such as vehicles and human from video streams can be
recognized by applying optical flow technique.
Abstract: The purpose of this study is to suggest direction for
future study of the energy-IT industry that will be used for framework to increase IT utilization in the energy industry. Recently, Green IT is a becoming global issue because of global environmental pollution.
Also, IT roles in energy industry are becoming more important.
However, the related studies were IT industry oriented that is not sufficient to make plan for Green energy. Therefore, after analyzing
existing studies related to Green energy and Green IT,
re-categorization for Green energy-IT industry was suggested. Direction of framework is based on energy industry that enable to link between energy and IT. The results of this study suggest comprehensive insight to Green energy-IT industry. Thus it is able to
provide useful implications and guidelines to increase IT utilization in the energy industry.
Abstract: The use and management of projects has risen to
a new prominence, with projects seen as critical to economic in
both the private and public sectors due challenging and dynamic
business environment. However, failure in managing project is
encountered regularly, which cause the waste of company
resources. The impacts of projects that failed to meet
stakeholders expectations have left behind long lasting negative
consequences in organization. Therefore, this research aims to
investigate on key success factors of project management in an
organization. It is believed that recognizing important factors
that contribute to successful project will help companies to
increase the overall profitability. 150 questionnaires were
distributed to respondents and 110 questionnaires were collected
and used in performing the data analysis. The result has strongly
supported the relationship between independent variables and
project performance.
Abstract: Vector quantization is a powerful tool for speech
coding applications. This paper deals with LPC Coding of speech
signals which uses a new technique called Multi Switched Split
Vector Quantization, This is a hybrid of two product code vector
quantization techniques namely the Multi stage vector quantization
technique, and Switched split vector quantization technique,. Multi
Switched Split Vector Quantization technique quantizes the linear
predictive coefficients in terms of line spectral frequencies. From
results it is proved that Multi Switched Split Vector Quantization
provides better trade off between bitrate and spectral distortion
performance, computational complexity and memory requirements
when compared to Switched Split Vector Quantization, Multi stage
vector quantization, and Split Vector Quantization techniques. By
employing the switching technique at each stage of the vector
quantizer the spectral distortion, computational complexity and
memory requirements were greatly reduced. Spectral distortion was
measured in dB, Computational complexity was measured in
floating point operations (flops), and memory requirements was
measured in (floats).
Abstract: This paper is a part of research, in which the way the
biomedical engineers follow in their work is analyzed. The goal of
this paper is to present a method for specification of user
requirements in the medical devices maintenance process. Data
Gathering Methods, Research Model Phases and Descriptive
Analysis is presented. These technology and verification rules can be
implemented in Medical devices maintenance management process to
the maintenance process.
Abstract: Droplet size distributions in the cold spray of a fuel
are important in observed combustion behavior. Specification of
droplet size and velocity distributions in the immediate downstream
of injectors is also essential as boundary conditions for advanced
computational fluid dynamics (CFD) and two-phase spray transport
calculations. This paper describes the development of a new model to
be incorporated into maximum entropy principle (MEP) formalism
for prediction of droplet size distribution in droplet formation region.
The MEP approach can predict the most likely droplet size and
velocity distributions under a set of constraints expressing the
available information related to the distribution.
In this article, by considering the mechanisms of turbulence
generation inside the nozzle and wave growth on jet surface, it is
attempted to provide a logical framework coupling the flow inside the
nozzle to the resulting atomization process. The purpose of this paper
is to describe the formulation of this new model and to incorporate it
into the maximum entropy principle (MEP) by coupling sub-models
together using source terms of momentum and energy. Comparison
between the model prediction and experimental data for a gas turbine
swirling nozzle and an annular spray indicate good agreement
between model and experiment.
Abstract: This paper presents the effect of driving a motor
vehicle on the stress levels of older drivers, indicated by monitoring
their hear rate increase whilst completing various everyday driving
tasks. Results suggest that whilst older female drivers heart rate varied
more significantly than males, the actual age of a participant did not
result in a significant change in heart rate due to stress, within the age
group tested. The analysis of the results indicates the most stressful
manoeuvres undertaken by the older drivers and highlights the tasks
which were found difficult with a view to implementing technologies
to aid the more senior driver in automotive travel.
Abstract: SeqWord Gene Island Sniffer, a new program for
the identification of mobile genetic elements in sequences of bacterial chromosomes is presented. This program is based on the
analysis of oligonucleotide usage variations in DNA sequences. 3,518 mobile genetic elements were identified in 637 bacterial
genomes and further analyzed by sequence similarity and the
functionality of encoded proteins. The results of this study are stored in an open database http://anjie.bi.up.ac.za/geidb/geidbhome.
php). The developed computer program and the database provide the information valuable for further investigation of the
distribution of mobile genetic elements and virulence factors among bacteria. The program is available for download at www.bi.up.ac.za/SeqWord/sniffer/index.html.
Abstract: This paper presents a hybrid electric scooter model developed and simulated using Matlab/Simulink. This hybrid scooter modeled has a parallel hybrid structure. The main propulsion units consist of a two stroke internal combustion engine and a hub motor attached to the front wheel of the scooter. The methodology used to optimize the energy and fuel consumption of the hybrid electric scooter is the multi-mode approach. Various case studies were presented to check the model and were compared to the literatures. Results shown that the model developed was feasible and valuable.