Abstract: The perfect operation of common Active Filters is depended on accuracy of identification system distortion. Also, using a suitable method in current injection and reactive power compensation, leads to increased filter performance. Due to this fact, this paper presents a method based on predictive current control theory in shunt active filter applications. The harmonics of the load current is identified by using o–d–q reference frame on load current and eliminating the DC part of d–q components. Then, the rest of these components deliver to predictive current controller as a Threephase reference current by using Park inverse transformation. System is modeled in discreet time domain. The proposed method has been tested using MATLAB model for a nonlinear load (with Total Harmonic Distortion=20%). The simulation results indicate that the proposed filter leads to flowing a sinusoidal current (THD=0.15%) through the source. In addition, the results show that the filter tracks the reference current accurately.
Abstract: In this paper, based on the past project cost and time
performance, a model for forecasting project cost performance is
developed. This study presents a probabilistic project control concept
to assure an acceptable forecast of project cost performance. In this
concept project activities are classified into sub-groups entitled
control accounts. Then obtain the Stochastic S-Curve (SS-Curve), for
each sub-group and the project SS-Curve is obtained by summing
sub-groups- SS-Curves. In this model, project cost uncertainties are
considered through Beta distribution functions of the project
activities costs required to complete the project at every selected time
sections through project accomplishment, which are extracted from a
variety of sources. Based on this model, after a percentage of the
project progress, the project performance is measured via Earned
Value Management to adjust the primary cost probability distribution
functions. Then, accordingly the future project cost performance is
predicted by using the Monte-Carlo simulation method.
Abstract: Principle component analysis is often combined with
the state-of-art classification algorithms to recognize human faces.
However, principle component analysis can only capture these
features contributing to the global characteristics of data because it is a
global feature selection algorithm. It misses those features
contributing to the local characteristics of data because each principal
component only contains some levels of global characteristics of data.
In this study, we present a novel face recognition approach using
non-negative principal component analysis which is added with the
constraint of non-negative to improve data locality and contribute to
elucidating latent data structures. Experiments are performed on the
Cambridge ORL face database. We demonstrate the strong
performances of the algorithm in recognizing human faces in
comparison with PCA and NREMF approaches.
Abstract: Earthmoving operations are a major part of many
construction projects. Because of the complexity and fast-changing
environment of such operations, the planning and estimating are
crucial on both planning and operational levels. This paper presents
the framework ofa microscopic discrete-event simulation system for
modeling earthmoving operations and conducting productivity
estimations on an operational level.A prototype has been developed
to demonstrate the applicability of the proposed framework, and this
simulation system is presented via a case study based on an actual
earthmoving project. The case study shows that the proposed
simulation model is capable of evaluating alternative operating
strategies and resource utilization at a very detailed level.
Abstract: This paper and its companion (Part 2) deal with
modeling and optimization of two NP-hard problems in production
planning of flexible manufacturing system (FMS), part type selection
problem and loading problem. The part type selection problem and
the loading problem are strongly related and heavily influence the
system-s efficiency and productivity. The complexity of the problems
is harder when flexibilities of operations such as the possibility of
operation processed on alternative machines with alternative tools are
considered. These problems have been modeled and solved
simultaneously by using real coded genetic algorithms (RCGA)
which uses an array of real numbers as chromosome representation.
These real numbers can be converted into part type sequence and
machines that are used to process the part types. This first part of the
papers focuses on the modeling of the problems and discussing how
the novel chromosome representation can be applied to solve the
problems. The second part will discuss the effectiveness of the
RCGA to solve various test bed problems.
Abstract: Back-to-back static synchronous compensator (BtBSTATCOM) consists of two back-to-back voltage-source converters (VSC) with a common DC link in a substation. This configuration extends the capabilities of conventional STATCOM that bidirectional active power transfer from one bus to another is possible. In this paper, VSCs are designed in quasi multi-pulse form in which GTOs are triggered only once per cycle in PSCAD/EMTDC. The design details of VSCs as well as gate switching circuits and controllers are fully represented. Regulation modes of BtBSTATCOM are verified and tested on a multi-machine power system through different simulation cases. The results presented in the form of typical time responses show that practical PI controllers are almost robust and stable in case of start-up, set-point change, and line faults.
Abstract: Improving performance measures in the construction
processes has been a major concern for managers and decision
makers in the industry. They seek for ways to recognize the key
factors which have the largest effect on the process. Identifying such
factors can guide them to focus on the right parts of the process in
order to gain the best possible result. In the present study design of
experiment (DOE) has been applied to a computer simulation model
of brick laying process to determine significant factors while
productivity has been chosen as the response of the experiment. To
this end, four controllable factors and their interaction have been
experimented and the best factor level has been calculated for each
one. The results indicate that three factors, namely, labor of brick,
labor of mortar and inter arrival time of mortar along with interaction
of labor of brick and labor of mortar are significant.
Abstract: Radio propagation from point-to-point is affected by
the physical channel in many ways. A signal arriving at a destination
travels through a number of different paths which are referred to as
multi-paths. Research in this area of wireless communications has
progressed well over the years with the research taking different
angles of focus. By this is meant that some researchers focus on
ways of reducing or eluding Multipath effects whilst others focus on
ways of mitigating the effects of Multipath through compensation
schemes. Baseband processing is seen as one field of signal
processing that is cardinal to the advancement of software defined
radio technology. This has led to wide research into the carrying out
certain algorithms at baseband. This paper considers compensating
for Multipath for Frequency Modulated signals. The compensation
process is carried out at Radio frequency (RF) and at Quadrature
baseband (QBB) and the results are compared. Simulations are
carried out using MatLab so as to show the benefits of working at
lower QBB frequencies than at RF.
Abstract: Heart disease (HD) is a major cause of morbidity and mortality in the modern society. Medical diagnosis is an important but complicated task that should be performed accurately and efficiently and its automation would be very useful. All doctors are unfortunately not equally skilled in every sub specialty and they are in many places a scarce resource. A system for automated medical diagnosis would enhance medical care and reduce costs. In this paper, a new approach based on coactive neuro-fuzzy inference system (CANFIS) was presented for prediction of heart disease. The proposed CANFIS model combined the neural network adaptive capabilities and the fuzzy logic qualitative approach which is then integrated with genetic algorithm to diagnose the presence of the disease. The performances of the CANFIS model were evaluated in terms of training performances and classification accuracies and the results showed that the proposed CANFIS model has great potential in predicting the heart disease.
Abstract: Rotation or tilt present in an image capture by digital
means can be detected and corrected using Artificial Neural Network
(ANN) for application with a Face Recognition System (FRS). Principal
Component Analysis (PCA) features of faces at different angles
are used to train an ANN which detects the rotation for an input image
and corrected using a set of operations implemented using another
system based on ANN. The work also deals with the recognition
of human faces with features from the foreheads, eyes, nose and
mouths as decision support entities of the system configured using
a Generalized Feed Forward Artificial Neural Network (GFFANN).
These features are combined to provide a reinforced decision for
verification of a person-s identity despite illumination variations. The
complete system performing facial image rotation detection, correction
and recognition using re-enforced decision support provides a
success rate in the higher 90s.
Abstract: Owing to extensive use of hydrogen in refining or
petrochemical units, it is essential to manage hydrogen network in
order to make the most efficient utilization of hydrogen. On the other
hand, hydrogen is an important byproduct not properly used through
petrochemical complexes and mostly sent to the fuel system. A few
works have been reported in literature to improve hydrogen network
for petrochemical complexes. In this study a comprehensive analysis
is carried out on petrochemical units using a modified automated
targeting technique which is applied to determine the minimum
hydrogen consumption. Having applied the modified targeting
method in two petrochemical cases, the results showed a significant
reduction in required fresh hydrogen.
Abstract: Partial Discharge measurement is a very important
means of assessing the integrity of insulation systems in a High
Voltage apparatus. In compressed gas insulation systems, floating
particles can initiate partial discharge activities which adversely
affect the working of insulation. Partial Discharges below the
inception voltage also plays a crucial in damaging the integrity of
insulation over a period of time. This paper discusses the effect of
loose and fixed Copper and Nichrome wire particles on the PD
characteristics in SF6-N2 (10:90) gas mixtures at a pressure of
0.4MPa. The Partial Discharge statistical parameters and their
correlation to the observed results are discussed.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: Qk
n has been shown as an alternative to the hypercube
family. For any even integer k ≥ 4 and any integer n ≥ 2, Qk
n is
a bipartite graph. In this paper, we will prove that given any pair of
vertices, w and b, from different partite sets of Qk
n, there exist 2n
internally disjoint paths between w and b, denoted by {Pi | 0 ≤ i ≤ 2n-1}, such that 2n-1
i=0 Pi covers all vertices of Qk
n. The result is
optimal since each vertex of Qk
n has exactly 2n neighbors.
Abstract: Shot boundary detection is a fundamental step for the organization of large video data. In this paper, we propose a new method for video gradual shots detection and classification, using advantages of fractal analysis and AIS-based classifier. Proposed features are “vertical intercept" and “fractal dimension" of each frame of videos which are computed using Fourier transform coefficients. We also used a classifier based on Clonal Selection Algorithm. We have carried out our solution and assessed it according to the TRECVID2006 benchmark dataset.
Abstract: Classes on creativity, innovation, and entrepreneurship
are becoming quite popular at universities throughout the world.
However, it is not easy for business students to get involved to
innovative activities, especially patent application. The present study
investigated how to enhance business students- intention to participate
in innovative activities and which incentives universities should
consider. A 22-item research scale was used, and confirmatory factor
analysis was conducted to verify its reliability and validity. Multiple
regression and discriminant analyses were also conducted. The results
demonstrate the effect of growth-need strength on innovative behavior
and indicate that the theory of planned behavior can explain and
predict business students- intention to participate in innovative
activities. Additionally, the results suggest that applying our proposed
model in practice would effectively strengthen business students-
intentions to engage in innovative activities.
Abstract: Lean manufacturing is a production philosophy made
popular by Toyota Motor Corporation (TMC). It is globally known as
the Toyota Production System (TPS) and has the ultimate aim of
reducing cost by thoroughly eliminating wastes or muda. TPS
embraces the Just-in-time (JIT) manufacturing; achieving cost
reduction through lead time reduction. JIT manufacturing can be
achieved by implementing Pull system in the production.
Furthermore, TPS aims to improve productivity and creating
continuous flow in the production by arranging the machines and
processes in cellular configurations. This is called as Cellular
Manufacturing Systems (CMS). This paper studies on integrating the
CMS with the Pull system to establish a Big Island-Pull system
production for High Mix Low Volume (HMLV) products in an
automotive component industry. The paper will use the build-in JIT
system steps adapted from TMC to create the Pull system production
and also create a shojinka line which, according to takt time, has the
flexibility to adapt to demand changes simply by adding and taking
out manpower. This will lead to optimization in production.
Abstract: This article proposes modeling, simulation and
kinematic and workspace analysis of a spatial cable suspended robot
as incompletely Restrained Positioning Mechanism (IRPM). These
types of robots have six cables equal to the number of degrees of
freedom. After modeling, the kinds of workspace are defined then an
statically reachable combined workspace for different geometric
structures of fixed and moving platform is obtained. This workspace
is defined as the situations of reference point of the moving platform
(center of mass) which under external forces such as weight and with
ignorance of inertial effects, the moving platform should be in static
equilibrium under conditions that length of all cables must not be
exceeded from the maximum value and all of cables must be at
tension (they must have non-negative tension forces). Then the effect
of various parameters such as the size of moving platform, the size of
fixed platform, geometric configuration of robots, magnitude of
applied forces and moments to moving platform on workspace of
these robots with different geometric configuration are investigated.
Obtained results should be effective in employing these robots under
different conditions of applied wrench for increasing the workspace
volume.
Abstract: The paper discusses the results obtained to predict
reinforcement in singly reinforced beam using Neural Net (NN),
Support Vector Machines (SVM-s) and Tree Based Models. Major
advantage of SVM-s over NN is of minimizing a bound on the
generalization error of model rather than minimizing a bound on
mean square error over the data set as done in NN. Tree Based
approach divides the problem into a small number of sub problems to
reach at a conclusion. Number of data was created for different
parameters of beam to calculate the reinforcement using limit state
method for creation of models and validation. The results from this
study suggest a remarkably good performance of tree based and
SVM-s models. Further, this study found that these two techniques
work well and even better than Neural Network methods. A
comparison of predicted values with actual values suggests a very
good correlation coefficient with all four techniques.
Abstract: Recently research on human wayfinding has focused
mainly on mental representations rather than processes of
wayfinding. The objective of this paper is to demonstrate the
rationality behind applying multi-agent simulation paradigm to the
modeling of rescuer team wayfinding in order to develop
computational theory of perceptual wayfinding in crisis situations
using image schemata and affordances, which explains how people
find a specific destination in an unfamiliar building such as a
hospital. The hypothesis of this paper is that successful navigation is
possible if the agents are able to make the correct decision through
well-defined cues in critical cases, so the design of the building
signage is evaluated through the multi-agent-based simulation. In
addition, a special case of wayfinding in a building, finding one-s
way through three hospitals, is used to demonstrate the model.
Thereby, total rescue time for rescue operation during building fire is
computed. This paper discuses the computed rescue time for various
signage localization and provides experimental result for
optimization of building signage design. Therefore the most
appropriate signage design resulted in the shortest total rescue time in
various situations.