Abstract: A laboratory set-up was designed to survey the
effectiveness of UV/O3 advanced oxidation process (AOP) for the
removal of Carbaryl from polluted water in batch reactor. The study
was carried out by UV/O3 process for water samples containing 1 to
20 mg/L of Carbaryl in distilled water. Also the range of drinking
water resources adjusted in synthetic water and effects of contact
time, pH and Carbaryl concentration were studied. The residual
pesticide concentration was determined by applying high
performance liquid chromatography (HPLC). The results indicated
that increasing of retention time and pH, enhances pesticide removal
efficiency. The removal efficiency has been affected by pesticide
initial concentration. Samples with low pesticide concentration
showed a remarkable removal efficiency compared to the samples
with high pesticide concentration. AOP method showed the removal
efficiencies of 80% to 100%. Although process showed high
performance for removal of pesticide from water samples, this
process has different disadvantages including complication,
intolerability, difficulty of maintenance and equipmental and
structural requirements.
Abstract: Column leach test has been performed to examine the
behavior of leaching of sodium, calcium and potassium in landfills.
In the column leach apparatus, two different layers of contaminated
and uncontaminated soils of different height ratios (ratio of depth of
contaminated soil to the depth of uncontaminated soil) are taken.
Water is poured from an overhead tank at a particular flowrate to the
inlet of the soil column for a certain ponding depth over the
contaminated soil. Subsequent infiltration causes leaching and the
leachates are collected from the bottom of the column. The
concentrations of Na, Ca and K in the leachate are measured using
flame photometry. The experiments are further extended by changing
the rates of flow from the overhead tank to the inlet of the column in
achieving the same ponding depth. The experiments are performed
for different scenarios in which the height ratios are altered and the
variations of concentrations of Na, Ca, and K are observed. The study
brings an estimation of leaching in landfill sites for different heights
and precipitation intensity where a ponding depth is maintained over
the landfill. It has been observed that the leaching behavior of Na,
Ca, and K are not similar. Calcium exhibits highest amount of
leaching compared to Sodium and Potassium under similar
experimental conditions.
Abstract: Walking and sit to stand are activities carried out by
all the people many times during the day, but physical disabilities due
to age and diseases create needs of assistive devices to help elderly
people during their daily life. This study aims to study the different
types and mechanisms of the assistive devices. We will analyze the
limitations and the challenges faced by the researchers in this field.
We will introduce the Assistive Device developed at the Egypt-Japan
University of Science and Technology, named E-JUST Assistive
Device (EJAD). EJAD will be a low cost intelligent assistive device
to help elders in walking and sit-to-stand activities.
Abstract: In recent five decades, textured yarns of polyester fiber produced by false twist method are the most
important and mass-produced manmade fibers. There are
many parameters of cross section which affect the physical and mechanical properties of textured yarns. These parameters
are surface area, perimeter, equivalent diameter, large
diameter, small diameter, convexity, stiffness, eccentricity, and hydraulic diameter. These parameters were evaluated by
digital image processing techniques. To find trends between production criteria and evaluated parameters of cross section, three criteria of production line have been adjusted and different types of yarns were produced. These criteria are
temperature, drafting ratio, and D/Y ratio. Finally the relations between production criteria and cross section parameters were
considered. The results showed that the presented technique can recognize and measure the parameters of fiber cross section in acceptable accuracy. Also, the optimum condition
of adjustments has been estimated from results of image analysis evaluation.
Abstract: Automatic keyphrase extraction is useful in efficiently
locating specific documents in online databases. While several
techniques have been introduced over the years, improvement on
accuracy rate is minimal. This research examines attribute scores for
author-supplied keyphrases to better understand how the scores affect
the accuracy rate of automatic keyphrase extraction. Five attributes
are chosen for examination: Term Frequency, First Occurrence, Last
Occurrence, Phrase Position in Sentences, and Term Cohesion
Degree. The results show that First Occurrence is the most reliable
attribute. Term Frequency, Last Occurrence and Term Cohesion
Degree display a wide range of variation but are still usable with
suggested tweaks. Only Phrase Position in Sentences shows a totally
unpredictable pattern. The results imply that the commonly used
ranking approach which directly extracts top ranked potential phrases
from candidate keyphrase list as the keyphrases may not be reliable.
Abstract: In this paper, we propose the pre-processor based on
the Evidence Supporting Measure of Similarity (ESMS) filter and also
propose the unified fusion approach (UFA) based on the general
fusion machine coupled with ESMS filter, which improve the
correctness and precision of information fusion in any fields of
application. Here we mainly apply the new approach to Simultaneous
Localization And Mapping (SLAM) of Pioneer II mobile robots. A
simulation experiment was performed, where an autonomous virtual
mobile robot with sonar sensors evolves in a virtual world map with
obstacles. By comparing the result of building map according to the
general fusion machine (here DSmT-based fusing machine and
PCR5-based conflict redistributor considereded) coupling with ESMS
filter and without ESMS filter, it shows the benefit of the selection of
the sources as a prerequisite for improvement of the information
fusion, and also testifies the superiority of the UFA in dealing with
SLAM.
Abstract: In this study, solid phase micro-extraction (SPME)
was optimized to improve the sensitivity and accuracy in
formaldehyde determination for plywood panels. Further work has
been carried out to compare the newly developed technique with
existing method which reacts formaldehyde collected in desiccators
with acetyl acetone reagent (DC-AA). In SPME, formaldehyde was
first derivatized with O-(2,3,4,5,6 pentafluorobenzyl)-hydroxylamine
hydrochloride (PFBHA) and analysis was then performed by gas
chromatography in combination with mass spectrometry (GC-MS).
SPME data subjected to various wood species gave satisfactory
results, with relative standard deviations (RSDs) obtained in the
range of 3.1-10.3%. It was also well correlated with DC values,
giving a correlation coefficient, RSQ, of 0.959. The quantitative
analysis of formaldehyde by SPME was an alternative in wood
industry with great potential
Abstract: The purposes of this study are to study political
information exposure, politicians- perceptions, political attitudes and
political participations among people in Bangkok Metropolitan Area.
The sample consisted of 420 which were selected by using accidental sampling method. Questionnaires were administered to all of the
respondents to obtain the data for this research. T-test, one-way ANOVA and Pearson-s correlation coefficient were used to analyze the data. The findings are as follows: The difference in gender,
education, income and occupation has significantly effect upon political information exposures. The difference in age, income has
significantly effect upon politicians- perceptions. The difference in income has significantly effect upon political attitudes. The
difference in gender, income and occupation has significantly effect
upon political participations. There were a significantly relations between political information exposures, political attitudes, political
participations and between politicians- perceptions, political attitudes and political participations.
Abstract: In the last decades, the problem of perforation
damage has been considered as the major factor for the
reduction of oil productivity. Underbalance perforation is
considered as one of the best means to minimize or overcome
this problem. By maintaining wellbore pressure lower than
formation pressure, perforation damage could be minimize or
eliminated. This can be achieved by the use of nontraditional
lightweight completion fluid. This paper presents the effect of
natural clay in formulating nontraditional completion fluid to
ensure successful perforation job and increase of production
rate. Natural clay is used as homogenizing agent to create a
stable and non-damaging low-density completion fluid.
Results indicate that the addition of natural clay dramatically
increase the stability of the final fluids. In addition, field test
has shown that the application of nontraditional completion
fluid increases oil production by three folds.
Abstract: The purpose of this study was to assess the value of Second Life among post-secondary instructors with experience using Second Life as an educational tool. Using Everett Rogers-s diffusion of innovations theory, survey respondents (N = 162), were divided into three adopter categories: innovators, early adopters and the early majority. Respondents were from 15 countries and 25 academic disciplines, indicating the considerable potential this innovation has to be adopted across many different borders and in many areas of academe. Nearly 94% of respondents said they plan to use Second Life again as an educational tool. However, no significant differences were found in instructors- levels of satisfaction with Second Life as an educational tool or their perceived effect on student learning across adopter categories. On the other hand, instructors who conducted class fully in Second Life were significantly more satisfied than those who used Second Life as only a small supplement to a real-world class. Overall, personal interest factors, rather than interpersonal communication factors, most influenced respondents- decision to adopt Second Life as an educational tool. In light of these findings, theoretical implications are discussed and practical suggestions are provided.
Abstract: Salary risk and demographic risk have been identified
as main risks in analyzing pension expenditure particularly in
Defined Benefit pension plan. Therefore, public pension plan in
Malaysia is studied to analyze pension expenditure due to salary and
demographic risk. Through the literature review and interview session
with several officers in public sector, factors affecting pension
expenditure are determined. Then, the inter-relationships between
these factors are analyzed through causal loop diagram. The System
Dynamics model is later developed using iThink software to show how
demographic and salary changes affect the pension expenditure. Then, by
using actual data, the impact of different policy scenarios on pension
expenditure is analyzed. It is shown that dynamics simulation model of
pension expenditure is useful to evaluate the impact of changes and
policy decisions on risk particularly involving demographic and salary risk.
Abstract: In this paper we describe our efforts to design and
implement an agent development framework that has the potential to
scale to the size of any underlying network suitable for various ECommerce
activities. The main novelty in our framework is it-s
capability to allow the development of sophisticated, secured agents
which are simple enough to be practical.
We have adopted FIPA agent platform reference Model as
backbone for implementation along with XML for agent
Communication and Java Cryptographic Extension and architecture
to realize the security of communication information between agents.
The advantage of our architecture is its support of agents
development in different languages and Communicating with each
other using a more open standard i.e. XML
Abstract: This study was designed to determine effect of
supplemented tomato pomace and fobrolytic enzyme on egg
production and egg quality. A total of 40 CP brown laying hens (95
week old) were used in completely randomized design in 2x2
factorial arrangement with or without enzyme supplementation. Four
dietary treatments included: Control (C), Fibrolytic enzyme (FE),
10% Tomato pomace (TP), and Fibrolytic enzyme + 10 % Tomato
pomace (FE+TP). Each of the four dietary treatments was fed up to
30 days (10 birds/treatment). Live performance, egg production, egg
weight and quality were determined for whole period. Dietary
treatments had no effect (P>0.05) on live performance, egg weight,
yolk color, and egg production. Therefore, laying hens fed diets with
fibrolytic enzyme were significantly (P
Abstract: Degradation of polymeric insulation systems of
electrical equipments increases the space charge density and the
concentration of electrical dipoles. By consequence, the maximum
values and the slopes of absorption/resorption (A/R) currents can
change with insulation systems ageing. In this paper, an analysis of
the nature of the A/R currents and the importance of their
components, especially the polarization current and the current given
by the space charge, is presented. The experimental study concerns
the A/R currents measurements of plane samples (made from
CALMICAGLAS tapes), virgin and thermally accelerated aged. The
obtained results show that the ageing process produces an increase of
the values and a decrease of shapes of the A/R currents. Finally, the
possibility of estimating insulations ageing state and lifetime from
A/R currents measurements is discussed.
Abstract: This work aims to test the application of computational fluid dynamics (CFD) modeling to fixed bed catalytic cracking reactors. Studies of CFD with a fixed bed design commonly use a regular packing with N=2 to define bed geometry. CFD allows us to obtain a more accurate view of the fluid flow and heat transfer mechanisms present in fixed bed equipment. Naphtha was used as feedstock and the reactor length was 80cm. It is divided in three sections that catalyst bed packed in the middle section of the reactor. The reaction scheme was involved one primary reaction and 24 secondary reactions. Because of high CPU times in these simulations, parallel processing have been used. In this study the coke formation process in fixed bed and empty tube reactor was simulated and coke in these reactors are compared. In addition, the effect of steam ratio and feed flow rate on coke formation was investigated.
Abstract: This research studied recycled wastes by Recyclable Material Bank project of 17 universities of Thailand for evaluation of reducing greenhouse gasses emission compared with landfilling activity during January 2011 to December 2011. The results showed that the projects collected total amount of recyclable wastes about 1,626.917 metric ton. The office paper has the largest amount among these recycled wastes (55.61 % of total recycled wastes). Groups of recycled waste can be prioritized from high to low according to their amount as paper, plastic, glass, mixed recyclables and metal, respectively. The project reduced greenhouse gasses emission equivalent to about 5,263.481 metric ton of carbon dioxide. The most significant recycled waste that affects the reduction of greenhouse gasses emission is office paper which is 73.45% of total reduced greenhouse gasses emission. According to amount of reduced greenhouse gasses emission, groups of recycled waste can be prioritized from high to low significances as paper, plastic, metal, mixed recyclables and glass, respectively.
Abstract: There have been significant improvements in automatic
voice recognition technology. However, existing systems still face difficulties,
particularly when used by non-native speakers with accents.
In this paper we address a problem of identifying the English accented
speech of speakers from different backgrounds. Once an accent is
identified the speech recognition software can utilise training set from
appropriate accent and therefore improve the efficiency and accuracy
of the speech recognition system. We introduced the Q factor, which
is defined by the sum of relationships between frequencies of the
formants. Four different accents were considered and experimented
for this research. A scoring method was introduced in order to
effectively analyse accents. The proposed concept indicates that the
accent could be identified by analysing their formants.
Abstract: Residual dye contents in textile dyeing wastewater have complex aromatic structures that are resistant to degrade in biological wastewater treatment. The objectives of this study were to determine the effectiveness of nanoscale zerovalent iron (NZVI) to decolorize Reactive Black 5 (RB5) and Reactive Red 198 (RR198) in synthesized wastewater and to investigate the effects of the iron particle size, iron dosage and solution pHs on the destruction of RB5 and RR198. Synthesized NZVI was confirmed by transmission electron microscopy (TEM), X-ray diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). The removal kinetic rates (kobs) of RB5 (0.0109 min-1) and RR198 (0.0111 min-1) by 0.5% NZVI were many times higher than those of microscale zerovalent iron (ZVI) (0.0007 min-1 and 0.0008 min-1, respectively). The iron dosage increment exponentially increased the removal efficiencies of both RB5 and RR198. Additionally, lowering pH from 9 to 5 increased the decolorization kinetic rates of both RB5 and RR198 by NZVI. The destruction of azo bond (N=N) in the chromophore of both reactive dyes led to decolorization of dye solutions.
Abstract: The paper deals with the kinematics and automated
calculation of intermittent mechanisms with radial cams. Currently,
electronic cams are increasingly applied in the drives of working link
mechanisms. Despite a huge advantage of electronic cams in their reprogrammability
or instantaneous change of displacement diagrams,
conventional cam mechanisms have an irreplaceable role in
production and handling machines. With high frequency of working
cycle periods, the dynamic load of the proper servomotor rotor
increases and efficiency of electronic cams strongly decreases.
Though conventional intermittent mechanisms with radial cams are
representatives of fixed automation, they have distinct advantages in
their high speed (high dynamics), positional accuracy and relatively
easy manufacture. We try to remove the disadvantage of firm
displacement diagram by reducing costs for simple design and
automated calculation that leads reliably to high-quality and
inexpensive manufacture.
Abstract: Control of complex systems is one of important files in complex systems, that not only relies on the essence of complex systems which is denoted by the core concept – emergence, but also embodies the elementary concept in control theory. Aiming at giving a clear and self-contained description of emergence, the paper introduces a formal way to completely describe the formation and dynamics of emergence in complex systems. Consequently, this paper indicates the Emergence-Oriented Control methodology that contains three kinds of basic control schemes: the direct control, the system re-structuring and the system calibration. As a universal ontology, the Emergence-Oriented Control provides a powerful tool for identifying and resolving control problems in specific systems.