Abstract: In this paper the behavior of fixed series compensated
extra high voltage transmission lines during faults is simulated. Many
over-voltage protection schemes for series capacitors are limited in
terms of size and performance, and are easily affected by
environmental conditions. While the need for more compact and
environmentally robust equipment is required. use of series
capacitors for compensating part of the inductive reactance of long
transmission lines increases the power transmission capacity.
Emphasis is given on the impact of modern capacitor protection
techniques (MOV protection). The simulation study is performed
using MATLAB/SIMULINK®and results are given for a three phase
and a single phase to ground fault.
Abstract: This work is an attempt to use the standard Smoothed
Particle Hydrodynamics methodology for the simulation of the
complex unsteady, free-surface flow in a rotating Turgo impulse
water turbine. A comparison of two different geometries was
conducted. The SPH method due to its mesh-less nature is capable of
capturing the flow features appearing in the turbine, without
diffusion at the water/air interface. Furthermore results are compared
with a commercial CFD package (Fluent®) and the SPH algorithm
proves to be capable of providing similar results, in much less time
than the mesh based CFD program. A parametric study was also
performed regarding the turbine inlet angle.
Abstract: Due to the complex network architecture, the mobile
adhoc network-s multihop feature gives additional problems to the
users. When the traffic load at each node gets increased, the
additional contention due its traffic pattern might cause the nodes
which are close to destination to starve the nodes more away from the
destination and also the capacity of network is unable to satisfy the
total user-s demand which results in an unfairness problem. In this
paper, we propose to create an algorithm to compute the optimal
MAC-layer bandwidth assigned to each flow in the network. The
bottleneck links contention area determines the fair time share which
is necessary to calculate the maximum allowed transmission rate used
by each flow. To completely utilize the network resources, we
compute two optimal rates namely, the maximum fair share and
minimum fair share. We use the maximum fair share achieved in
order to limit the input rate of those flows which crosses the
bottleneck links contention area when the flows that are not allocated
to the optimal transmission rate and calculate the following highest
fair share. Through simulation results, we show that the proposed
protocol achieves improved fair share and throughput with reduced
delay.
Abstract: Recently studies in area of supply chain network
(SCN) have focused on the disruption issues in distribution systems.
Also this paper extends the previous literature by providing a new biobjective
model for cost minimization of designing a three echelon
SCN across normal and failure scenarios with considering multi
capacity option for manufacturers and distribution centers. Moreover,
in order to solve the problem by means of LINGO software, novel
model will be reformulated through a branch of LP-Metric method
called Min-Max approach.
Abstract: The contamination of 15 ground water resources
of a selected region earmarked for the emergency supply
of population has been monitored. The resources have been selected
on the basis of previous assessment of natural conditions
and the exploitation of territory in their surroundings and infiltration
area. Two resources out of 15 have been excluded from further
exploitation, because they have not met some of the 72 assessed
hygienic indicators of extended analysis. The remaining 13 resources
have been the subject of health risk analysis in relation
to the contamination by arsenic, lead, cadmium, mercury, nickel and
manganese. The risk analysis proved that all 13 resources meet
health standards with regard to the above mentioned purposefully
selected elements and may thus be included into crisis plans. Water
quality of ground resources may be assessed in the same way
with regard to other contaminants.
Abstract: The thermal, epithermal and fast fluxes were
calculated for three irradiation channels at Egypt Second Research
Reactor (ETRR-2) using CITVAP code. The validity of the
calculations was verified by experimental measurements. There are
some deviations between measurements and calculations. This is due
to approximations in the calculation models used, homogenization of
regions, condensation of energy groups and uncertainty in nuclear
data used. Neutron flux data for the three irradiation channels are
now available. This would enable predicting the irradiation
conditions needed for future radioisotope production.
Abstract: This research deals with techno economic analysis to select the most economic desalination method for Asalouyeh combined cycle power plant . Due to lack of fresh water, desalination of sea water is necessary to provide required DM water of Power Plant. The most common desalination methods are RO, MSF, MED, and MED–TVC. In this research, methods of RO, MED, and MED– TVC have been compared. Simulation results show that recovery of heat of exhaust gas of main stack is optimum case for providing DM water required for injected steam of MED desalination. This subject is very important because of improving thermal efficiency of power plant using extra heat recovery. Also, it has been shown that by adding 3 rows of finned tube to de-aerator evaporator, which is very simple and low cost, required steam for generating 5200 m3/day of desalinated water is obtainable.
Abstract: Several studies have shown the association between
ambient particulate matter (PM) and adverse health effects and
climate change, thus highlighting the need to limit the anthropogenic
sources of PM. PM Exposure is commonly monitored as mass
concentration of PM10 (particle aerodynamic diameter < 10μm) or
PM2.5 (particle aerodynamic diameter < 2.5μm), although increasing
toxicity with decreasing aerodynamic diameter has been reported due
to increased surface area and enhanced chemical reactivity with other
species. Additionally, the light scattering properties of PM increases
with decreasing size. Hence, it is important to study the chemical
characterization of finer fraction of the particulate matter and to
identify their sources so that they can be controlled appropriately to a
large extent at the sources before reaching to the receptors.
Abstract: Creep stresses and strain rates have been obtained
for a thin rotating disc having variable density with inclusion by
using Seth-s transition theory. The density of the disc is assumed to
vary radially, i.e. ( ) 0 ¤ü ¤ü r/b m - = ; ¤ü 0 and m being real positive
constants. It has been observed that a disc, whose density increases
radially, rotates at higher angular speed, thus decreasing the
possibility of a fracture at the bore, whereas for a disc whose
density decreases radially, the possibility of a fracture at the bore
increases.
Abstract: The hypercube Qn is one of the most well-known
and popular interconnection networks and the k-ary n-cube Qk
n is
an enlarged family from Qn that keeps many pleasing properties
from hypercubes. In this article, we study the panpositionable
hamiltonicity of Qk
n for k ≥ 3 and n ≥ 2. Let x, y of V (Qk
n)
be two arbitrary vertices and C be a hamiltonian cycle of Qk
n.
We use dC(x, y) to denote the distance between x and y on the
hamiltonian cycle C. Define l as an integer satisfying d(x, y) ≤ l ≤ 1
2 |V (Qk
n)|. We prove the followings:
• When k = 3 and n ≥ 2, there exists a hamiltonian cycle C
of Qk
n such that dC(x, y) = l.
• When k ≥ 5 is odd and n ≥ 2, we request that l /∈ S
where S is a set of specific integers. Then there exists a
hamiltonian cycle C of Qk
n such that dC(x, y) = l.
• When k ≥ 4 is even and n ≥ 2, we request l-d(x, y) to be
even. Then there exists a hamiltonian cycle C of Qk
n such
that dC(x, y) = l.
The result is optimal since the restrictions on l is due to the
structure of Qk
n by definition.
Abstract: In this paper, we present parallel alternating two-stage methods for solving linear system Ax = b, where A is a monotone matrix or an H-matrix. And we give some convergence results of these methods for nonsingular linear system.
Abstract: A zero-field ferromagnetic Ising model is utilized to
simulate the propagation of infection in a population that assumes a
square lattice structure. The rate of infection increases with
temperature. The disease spreads faster among individuals with low J
values. Such effect, however, diminishes at higher temperatures.
Abstract: This paper describes how the correct endian mode of
the TMS320C6713 DSK board can be identified. It also explains how
the TMS320C6713 DSK board can be used in the little endian and in
the big endian modes for assembly language programming in
particular and for signal processing in general. Similarly, it discusses
how crucially important it is for a user of the TMS320C6713 DSK
board to identify the mode of operation and then use it correctly
during the development stages of the assembly language
programming; otherwise, it will cause unnecessary confusion and
erroneous results as far as storing data into the memory and loading
data from the memory is concerned. Furthermore, it highlights and
strongly recommends to the users of the TMS320C6713 DSK board
to be aware of the availability and importance of various display
options in the Code Composer Studio (CCS) for correctly
interpreting and displaying the desired data in the memory. The
information presented in this paper will be of great importance and
interest to those practitioners and developers who wants to use the
TMS320C6713 DSK board for assembly language programming as
well as input-output signal processing manipulations. Finally,
examples that clearly illustrate the concept are presented.
Abstract: Transient simulation of power electronic circuits is of
considerable interest to the designer. The switching nature of the
devices used permits development of specialized algorithms which
allow a considerable reduction in simulation time compared to
general purpose simulation algorithms. This paper describes a
method used to simulate a power electronic circuits using the
SIMULINK toolbox within MATLAB software. Theoretical results
are presented provides the basis of transient analysis of a power
electronic circuits.
Abstract: Chronic diseases prevailed along with economic
growth as well as life style changed in recent years in Taiwan.
According to the governmental statistics, hypertension related disease
is the tenth of death causes with 1,816 died directly from hypertension
in 2010. There were more death causes amongst the top ten had been
proofed that having strong association with the hypertension, such as
heart diseases, cardiovascular diseases, and diabetes. Hypertension or
High blood pressure is one of the major indicators for chronic diseases,
and was generally perceived as the major causes of mortality. The
literature generally suggested that regular physical exercise was
helpful to prevent the occurrence or to ease the progress of a
hypertension. This paper reported the process and outcomes in
detailed of an improvement project of physical exercise intervention
specific for hypertension patients. Physical information were
measured before and after the project to obtain information such as
weight, waistline, cholesterol (HD & LD), blood examination, as well
as self-perceived health status. The intervention project involved a
six-week exercise program, of which contained three times a week, 30
minutes of tutored physical exercise intervention. The project had
achieved several gains in changing the subjects- behavior in terms of
many important biophysical indexes. Around 20% of the participants
had significantly improved their cholesterols, BMI, and changed
unhealthy behaviors. Results from the project were encouraging, and
would be good reference for other samples.
Abstract: Sedimentation is a hydraulic phenomenon that is
emerging as a serious challenge in river engineering. When the flow
reaches a certain state that gather potential energy, it shifts the
sediment load along channel bed. The transport of such materials can
be in the form of suspended and bed loads. The movement of these
along the river course and channels and the ways in which this could
influence the water intakes is considered as the major challenges for
sustainable O&M of hydraulic structures. This could be very serious
in arid and semi-arid regions like Iran, where inappropriate watershed
management could lead to shifting a great deal of sediments into the
reservoirs and irrigation systems. This paper aims to investigate
sedimentation in the Western Canal of Dez Diversion Weir in Iran,
identifying factors which influence the process and provide ways in
which to mitigate its detrimental effects by using the SHARC
Software.
For the purpose of this paper, data from the Dezful water authority
and Dezful Hydrometric Station pertinent to a river course of about 6
Km were used.
Results estimated sand and silt bed loads concentrations to be 193
ppm and 827ppm respectively. Given the available data on average
annual bed loads and average suspended sediment loads of 165ppm
and 837ppm, there was a significant statistical difference (16%)
between the sand grains, whereas no significant difference (1.2%)
was find in the silt grain sizes. One explanation for such finding
being that along the 6 Km river course there was considerable
meandering effects which explains recent shift in the hydraulic
behavior along the stream course under investigation. The sand
concentration in downstream relative to present state of the canal
showed a steep descending curve. Sediment trapping on the other
hand indicated a steep ascending curve. These occurred because the
diversion weir was not considered in the simulation model.
Abstract: In a product development process, understanding the functional behavior of the system, the role of components in achieving functions and failure modes if components/subsystem fails its required function will help develop appropriate design validation and verification program for reliability assessment. The integration of these three issues will help design and reliability engineers in identifying weak spots in design and planning future actions and testing program. This case study demonstrate the advantage of unascertained theory described in the subjective cognition uncertainty, and then applies blind number (BN) theory in describing the uncertainty of the mechanical system failure process and the same time used the same theory in bringing out another mechanical reliability system model. The practical calculations shows the BN Model embodied the characters of simply, small account of calculation but betterforecasting capability, which had the value of macroscopic discussion to some extent.
Abstract: In this paper, we proposed an efficient data
compression strategy exploiting the multi-resolution characteristic of
the wavelet transform. We have developed a sensor node called
“Smart Sensor Node; SSN". The main goals of the SSN design are
lightweight, minimal power consumption, modular design and robust
circuitry. The SSN is made up of four basic components which are a
sensing unit, a processing unit, a transceiver unit and a power unit.
FiOStd evaluation board is chosen as the main controller of the SSN
for its low costs and high performance. The software coding of the
implementation was done using Simulink model and MATLAB
programming language. The experimental results show that the
proposed data compression technique yields recover signal with good
quality. This technique can be applied to compress the collected data
to reduce the data communication as well as the energy consumption
of the sensor and so the lifetime of sensor node can be extended.
Abstract: The purpose of this work is fast design optimization of
the seal chamber. The study includes the mass transfer between lower
and upper chamber on seal chamber for hot water application pumps.
The use of Fluent 12.1 commercial code made it possible to capture
complex flow with heat-mass transfer, radiation, Tailor instability,
and buoyancy effect. Realizable k-epsilon model was used for
turbulence modeling. Radiation heat losses were taken into account.
The temperature distribution at seal region is predicted with respect
to heat addition.
Results show the possibilities of the model simplifications by
excluding the water domain in low chamber from calculations. CFD
simulations permit to improve seal chamber design to meet target
water temperature around the seal. This study can be used for the
analysis of different seal chamber configurations.
Abstract: This paper introduces an adiabatic register file based
on two-phase CPAL (Complementary Pass-Transistor Adiabatic
Logic circuits) with power-gating scheme, which can operate on a
single-phase power clock. A 32×32 single-phase adiabatic register file
with power-gating scheme has been implemented with TSMC 0.18μm
CMOS technology. All the circuits except for the storage cells employ
two-phase CPAL circuits, and the storage cell is based on the
conventional memory one. The two-phase non-overlap power-clock
generator with power-gating scheme is used to supply the proposed
adiabatic register file. Full-custom layouts are drawn. The energy and
functional simulations have been performed using the net-list
extracted from their layouts. Compared with the traditional static
CMOS register file, HSPICE simulations show that the proposed
adiabatic register file can work very well, and it attains about 73%
energy savings at 100 MHz.