Abstract: Masonry cavity walls are loaded by wind pressure and vertical load from upper floors. These loads results in bending moments and compression forces in the ties connecting the outer and the inner wall in a cavity wall. Large cavity walls are furthermore loaded by differential movements from the temperature gradient between the outer and the inner wall, which results in critical increase of the bending moments in the ties. Since the ties are loaded by combined compression and moment forces, the loadbearing capacity is derived from instability equilibrium equations. Most of them are iterative, since exact instability solutions are complex to derive, not to mention the extra complexity introducing dimensional instability from the temperature gradients. Using an inverse variable substitution and comparing an exact theory with an analytical instability solution a method to design tie-connectors in cavity walls was developed. The method takes into account constraint conditions limiting the free length of the wall tie, and the instability in case of pure compression which gives an optimal load bearing capacity. The model is illustrated with examples from praxis.
Abstract: Compost manufacturing plants are one of units where
wastewater is produced in significantly large amounts. Wastewater
produced in these plants contains high amounts of substrate (organic
loads) and is classified as stringent waste which creates significant
pollution when discharged into the environment without treatment. A
compost production plant in the one of the Iran-s province treating
200 tons/day of waste is one of the most important environmental
pollutant operations in this zone. The main objectives of this paper
are to investigate the compost wastewater treatability in hybrid
anaerobic reactors with an upflow-downflow arrangement, to
determine the kinetic constants, and eventually to obtain an
appropriate mathematical model. After starting the hybrid anaerobic
reactor of the compost production plant, the average COD removal
rate efficiency was 95%.
Abstract: Both prognostic and diagnostic modes of a 3D baroclinic
model in hydrodynamic and sediment transport models of
the Princeton Ocean Model (POM) were conducted to separate
prognose and diagnose effects of different hydrodynamic factors on
transport of suspended sediment discharged from the rivers to the
Gulf of Thailand (GoT). Both transport modes of suspended sediment
distribution in the GoT were numerically simulated. It could be
concluded that the suspended sediment discharged from the rivers
around the GoT. Most of sediments in estuaries and coastal areas are
deposited outside the GoT under the condition of wind-driven current,
and very small amount of the sediments of them are transported
faraway. On the basis of wind forcing, sediments from the lower
GoT to the upper GoT are mainly transported south-northwestward
and also continuously moved north-southwestward. An obvious 3D
characteristic of suspended sediment transport is produced in the
wind-driven current residual circulation condition. In this study, the
transport patterns at the third layer are generally consistent with
the typhoon-induced strong currents in two case studies of Typhoon
Linda 1997. The case studies presented the prognostic and diagnostic
modes during 00UTC28OCT1997 to 12UTC06NOV1997 in a short
period with the current condition for pre-operation of the suspended
sediment transport model in estuaries and coastal areas.
Abstract: A numerical investigation has carried out to understand the melting characteristics of phase change material (PCM) in a fin type latent heat storage with the addition of embedded aluminum spiral fillers. It is known that melting performance of PCM can be significantly improved by increasing the number of embedded metallic fins in the latent heat storage system but to certain values where only lead to small improvement in heat transfer rate. Hence, adding aluminum spiral fillers within the fin gap can be an option to improve heat transfer internally. This paper presents extensive computational visualizations on the PCM melting patterns of the proposed fin-spiral fillers configuration. The aim of this investigation is to understand the PCM-s melting behaviors by observing the natural convection currents movement and melting fronts formation. Fluent 6.3 simulation software was utilized in producing twodimensional visualizations of melting fractions, temperature distributions and flow fields to illustrate the melting process internally. The results show that adding aluminum spiral fillers in Fin type latent heat storage can promoted small but more active natural convection currents and improve melting of PCM.
Abstract: The aim of this research is to develop a fast and
reliable surveillance system based on a personal digital assistant
(PDA) device. This is to extend the capability of the device to detect
moving objects which is already available in personal computers.
Secondly, to compare the performance between Background
subtraction (BS) and Temporal Frame Differencing (TFD) techniques
for PDA platform as to which is more suitable. In order to reduce
noise and to prepare frames for the moving object detection part,
each frame is first converted to a gray-scale representation and then
smoothed using a Gaussian low pass filter. Two moving object
detection schemes i.e., BS and TFD have been analyzed. The
background frame is updated by using Infinite Impulse Response
(IIR) filter so that the background frame is adapted to the varying
illuminate conditions and geometry settings. In order to reduce the
effect of noise pixels resulting from frame differencing
morphological filters erosion and dilation are applied. In this
research, it has been found that TFD technique is more suitable for
motion detection purpose than the BS in term of speed. On average
TFD is approximately 170 ms faster than the BS technique
Abstract: Building life cycle will never be excused from the existence of defects and deterioration. They are common problems in building, existed in newly build or in aged building. Buildings constructed from wood are indeed affected by its agent and serious defects and damages can reduce values to a building. In repair works, it is important to identify the causes and repair techniques that best suites with the condition. This paper reviews the conservation of traditional timber mosque in Malaysia comprises the concept, principles and approaches of mosque conservation in general. As in conservation practice, wood in historic building can be conserved by using various restoration and conservation techniques which this can be grouped as Fully and Partial Replacement, Mechanical Reinforcement, Consolidation by Impregnation and Reinforcement, Removing Paint and also Preservation of Wood and Control Insect Invasion, as to prolong and extended the function of a timber in a building. It resulted that the common techniques adopted in timber mosque conservation are from the conventional ways and the understanding of the repair technique requires the use of only preserve wood to prevent the future immature defects.
Abstract: This paper studies the optimum design for reducing
optical loss of an 8x8 mechanical type optical switch due to the
temperature change. The 8x8 optical switch is composed of a base, 8
input fibers, 8 output fibers, 3 fixed mirrors and 17 movable mirrors.
First, an innovative switch configuration is proposed with
thermal-compensated design. Most mechanical type optical switches
have a disadvantage that their precision and accuracy are influenced
by the ambient temperature. Therefore, the thermal-compensated
design is to deal with this situation by using materials with different
thermal expansion coefficients (α). Second, a parametric modeling
program is developed to generate solid models for finite element
analysis, and the thermal and structural behaviors of the switch are
analyzed. Finally, an integrated optimum design program, combining
Autodesk Inventor Professional software, finite element analysis
software, and genetic algorithms, is developed for improving the
thermal behaviors that the optical loss of the switch is reduced. By
changing design parameters of the switch in the integrated design
program, the final optimum design that satisfies the design constraints
and specifications can be found.
Abstract: We present a visualization technique for radial drawing of trees consisting of two slightly different algorithms. Both of them make use of node-link diagrams for visual encoding. This visualization creates clear drawings without edge crossing. One of the algorithms is suitable for real-time visualization of large trees, as it requires minimal recalculation of the layout if leaves are inserted or removed from the tree; while the other algorithm makes better utilization of the drawing space. The algorithms are very similar and follow almost the same procedure but with different parameters. Both algorithms assign angular coordinates for all nodes which are then converted into 2D Cartesian coordinates for visualization. We present both algorithms and discuss how they compare to each other.
Abstract: Recognizing human action from videos is an active
field of research in computer vision and pattern recognition. Human
activity recognition has many potential applications such as video
surveillance, human machine interaction, sport videos retrieval and
robot navigation. Actually, local descriptors and bag of visuals words
models achieve state-of-the-art performance for human action
recognition. The main challenge in features description is how to
represent efficiently the local motion information. Most of the
previous works focus on the extension of 2D local descriptors on 3D
ones to describe local information around every interest point. In this
paper, we propose a new spatio-temporal descriptor based on a spacetime
description of moving points. Our description is focused on an
Accordion representation of video which is well-suited to recognize
human action from 2D local descriptors without the need to 3D
extensions. We use the bag of words approach to represent videos.
We quantify 2D local descriptor describing both temporal and spatial
features with a good compromise between computational complexity
and action recognition rates. We have reached impressive results on
publicly available action data set
Abstract: This paper describes topic of computer simulation with regard to the ground movement above an underground mine. Simulation made with software package ADINA for nonlinear elastic-plastic analysis with finite elements method. The one of representative profiles from Mine 'Stara Jama' in Zenica has been investigated. A collection and selection of both geo-mechanical data and geometric parameters of the mine was necessary for performing these simulations. Results of estimation have been compared with measured values (vertical displacement of surface), and then simulation performed with assumed dynamic and dimensions of excavation, over a period of time. Results are presented with bitmaps and charts.
Abstract: To produce sugar and ethanol, sugarcane processing
generates several agricultural residues, being straw and bagasse is
considered as the main among them. And what to do with this
residues has been subject of many studies and experiences in an
industry that, in recent years, highlighted by the ability to transform
waste into valuable products such as electric power. Cellulose is the
main component of these materials. It is the most common organic
polymer and represents about 1.5 x 1012 tons of total production of
biomass per year and is considered an almost inexhaustible source of
raw material. Pretreatment with mineral acids is one of the most
widely used as stage of cellulose extraction from lignocellulosic
materials for solubilizing most of the hemicellulose content. This
study had as goal to find the best reaction time of sugarcane bagasse
pretreatment with sulfuric acid in order to minimize the losses of
cellulose concomitantly with the highest possible removal of
hemicellulose and lignin. It was found that the best time for this
reaction was 40 minutes, in which it was reached a loss of
hemicelluloses around 70% and lignin and cellulose, around 15%.
Over this time, it was verified that the cellulose loss increased and
there was no loss of lignin and hemicellulose.
Abstract: Many commercial processes are available for the
removal of H2S from gaseous streams. The desulfurization of gas
streams using aqueous ferric sulfate solution as washing liquor is
studied. Apart from sulfur, only H2O is generated in the process, and
consequently, no waste treatment facilities are required. A distinct
advantage of the process is that the reaction of H2S with is so rapid
and complete that there remains no danger of discharging toxic waste
gas. In this study, the reactive absorption of hydrogen sulfide into
aqueous ferric sulfate solution has been studied and design
calculations for equipments have been done and effective operation
parameters on this process considered. Results show that high
temperature and low pressure are suitable for absorption reaction.
Variation of hydrogen sulfide concentration and Fe3+ concentration
with time in absorption reaction shown that the reaction of ferric
sulfate and hydrogen sulfide is first order with respect to the both
reactant. At low Fe2(SO4)3 concentration the absorption rate of H2S
increase with increasing the Fe2(SO4)3 concentration. At higher
concentration a decrease in the absorption rate was found. At higher
concentration of Fe2(SO4)3, the ionic strength and viscosity of
solution increase remarkably resulting in a decrease of solubility,
diffusivity and hence absorption rate.
Abstract: Student-s movements have been going increasing in
last decades. International students can have different psychological
and sociological problems in their adaptation process. Depression is
one of the most important problems in this procedure. This research
purposed to reveal level of foreign students- depression, kinds of
interpersonal communication networks (host/ethnic interpersonal
communication) and media usage (host/ethnic media usage).
Additionally study aimed to display the relationship between
depression and communication (host/ethnic interpersonal
communication and host/ethnic media usage) among foreign
university students. A field research was performed among 283
foreign university students who have been attending 8 different
universities in Turkey. A purposeful sampling technique was used in
this research cause of data collect facilities. Results indicated that
58.3% of foreign students- depression stage was “intermediate" while
33.2% of foreign students- depression level was “low". Add to this,
host interpersonal communication behaviors and Turkish web sites
usages were negatively and significantly correlated with depression.
Abstract: Among the technologies available to reduce methane
emitted from the pig industry, biofiltration seems to be an effective
and inexpensive solution. In methane (CH4) biofiltration, nitrogen is
an important macronutrient for the microorganisms growth. The
objective of this research project was to study the effect of
ammonium (NH4
+) on the performance, the biomass production and
the nitrogen conversion of a biofilter treating methane. For NH4
+
concentrations ranging from 0.05 to 0.5 gN-NH4
+/L, the CH4 removal
efficiency and the dioxide carbon production rate decreased linearly
from 68 to 11.8 % and from 7.1 to 0.5 g/(m3-h), respectively. The dry
biomass content varied from 4.1 to 5.8 kg/(m3 filter bed). For the
same range of concentrations, the ammonium conversion decreased
while the specific nitrate production rate increased. The specific
nitrate production rate presented negative values indicating
denitrification in the biofilter.
Abstract: This research study examines cases of Saudi Arabian
universities and female academics for work environment issues
within the context of design management applications. The study
proposes use of design research, ergonomics and systems design
thinking to develop the university design which facilitates removal of
physical and cognitive barriers for female academics. Review of
literature demonstrates that macro and micro ergonomic combined
with design management and system design strategies can
significantly improve the workplace design for female academics.
The university design model would be prepared based on the analyses
of primary data obtained from archived documents, participants'
observation logs, photo audits, focus groups and semi-structured
interviews of currently employed female academics in the selected
case universities.
Abstract: Viscous heating becomes significant in the high speed
resin coating process of glass fibers for optical fiber manufacturing.
This study focuses on the coating resin flows inside the capillary
coating die of optical fiber coating applicator and they are numerically
simulated to examine the effects of viscous heating and subsequent
temperature increase in coating resin. Resin flows are driven by fast
moving glass fiber and the pressurization at the coating die inlet, while
the temperature dependent viscosity of liquid coating resin plays an
important role in the resin flow. It is found that the severe viscous
heating near the coating die wall profoundly alters the radial velocity
profiles and that the increase of final coating thickness by die
pressurization is amplified if viscous heating is present.
Abstract: People have always needed to believe in some
supernatural power, which could explain nature phenomena.
Different kinds of religions like Christianity, Hinduism, Islam,
Buddhism have thought believers in all world, how to behave
themselves. We think the most important role of religion in modern
society most important role of religion in modern society is safety of
the People. World and traditional religion played a prominent role in
the socio-cultural progress, and in the development of man as a
spiritual being. At the heart of religious morals the belief in god and
responsibility before it lies and specifies religious and ethical values
and categories . The religion is based on ethical standards historically
developed by society, requirements and concepts, but it puts all
social and moral relations of the person in dependence on religious
values. For everything that the believer makes on a debt or a duty, he
bears moral responsibility before conscience, people and god. The
concept of value of religious morals takes the central place because
the religion from all forms of public consciousness most values is
painted as it is urged to answer vital questions. Any religion not only
considers questions of creation of the world, sense of human
existence, relationship of god and the person, but also offers the
ethical concept, develops rules of behavior of people. The religion a
long time dominated in the history of culture, and during this time
created a set of cultural and material values. The identity of Kazakh
culture can be defined as a Cultural identity traditional ,national
identity and the identity values developed by Kazakh people in
process of cultural-historical development, promoting formation of
Kazakh culture identity on public consciousness. Identity is the
historical process but always the tradition exists in it as a component
of stability, as a component of self that what this identity formed .
Abstract: This paper describes the design concepts and
implementation of a 5-Joint mechanical arm for a rescue robot named
CEO Mission II. The multi-joint arm is a five degree of freedom
mechanical arm with a four bar linkage, which can be stretched to
125 cm. long. It is controlled by a teleoperator via the user-friendly
control and monitoring GUI program. With Inverse Kinematics
principle, we developed the method to control the servo angles of all
arm joints to get the desired tip position. By clicking the determined
tip position or dragging the tip of the mechanical arm on the
computer screen to the desired target point, the robot will compute
and move its multi-joint arm to the pose as seen on the GUI screen.
The angles of each joint are calculated and sent to all joint servos
simultaneously in order to move the mechanical arm to the desired
pose at once. The operator can also use a joystick to control the
movement of this mechanical arm and the locomotion of the robot.
Many sensors are installed at the tip of this mechanical arm for
surveillance from the high level and getting the vital signs of victims
easier and faster in the urban search and rescue tasks. It works very
effectively and easy to control. This mechanical arm and its software
were developed as a part of the CEO Mission II Rescue Robot that
won the First Runner Up award and the Best Technique award from
the Thailand Rescue Robot Championship 2006. It is a low cost,
simple, but functioning 5-Jiont mechanical arm which is built from
scratch, and controlled via wireless LAN 802.11b/g. This 5-Jiont
mechanical arm hardware concept and its software can also be used
as the basic mechatronics to many real applications.
Abstract: Virtual touch screen using camera is an ordinary screen which uses a camera to imitate the touch screen by taking a picture of an indicator, e.g., finger, which is laid on the screen, converting the indicator tip position on the picture to the position on the screen, and moving the cursor on the screen to that position. In fact, the indicator is not laid on the screen directly, but it is intervened by the cover at some intervals. In spite of this gap, if the eye-indicator-camera angle is not large, the mapping from the indicator tip positions on the image to the corresponding cursor positions on the screen is not difficult and could be done with a little error. However, the larger the angle is, the bigger the error in the mapping occurs. This paper proposes cursor position estimation model for virtual touch screen using camera which could eliminate this kind of error. The proposed model (i) moves the on-screen pilot cursor to the screen position which locates on the screen at the position just behind the indicator tip when the indicator tip has been looked from the camera position, and then (ii) converts that pilot cursor position to the desirable cursor position (the position on the screen when it has been looked from the user-s eye through the indicator tip) by using the bilinear transformation. Simulation results show the correctness of the estimated cursor position by using the proposed model.
Abstract: One very interesting field of research in Pattern Recognition that has gained much attention in recent times is Gesture Recognition. In this paper, we consider a form of dynamic hand gestures that are characterized by total movement of the hand (arm) in space. For these types of gestures, the shape of the hand (palm) during gesturing does not bear any significance. In our work, we propose a model-based method for tracking hand motion in space, thereby estimating the hand motion trajectory. We employ the dynamic time warping (DTW) algorithm for time alignment and normalization of spatio-temporal variations that exist among samples belonging to the same gesture class. During training, one template trajectory and one prototype feature vector are generated for every gesture class. Features used in our work include some static and dynamic motion trajectory features. Recognition is accomplished in two stages. In the first stage, all unlikely gesture classes are eliminated by comparing the input gesture trajectory to all the template trajectories. In the next stage, feature vector extracted from the input gesture is compared to all the class prototype feature vectors using a distance classifier. Experimental results demonstrate that our proposed trajectory estimator and classifier is suitable for Human Computer Interaction (HCI) platform.