Abstract: The objective of this paper is to analyze the
performance of a double-sided axial flux permanent magnet
brushless DC (AFPM BLDC) motor with two-phase winding.
To study the motor operation, a mathematical dynamic model
has been proposed for motor, which became the basis for
simulations that were performed using MATLAB/SIMULINK
software package. The results of simulations were presented
in form of the waveforms of selected quantities and the
electromechanical characteristics performed by the motor. The
calculation results show that the two-phase motor version
develops smooth torque and reaches high efficiency. The twophase
motor can be applied where more smooth torque is
required. Finally a study on the influence of switching angle
on motor performance shows that when advance switching
technique is used, the motor operates with the highest
efficiency.
Abstract: Modeling of Panel Zone (PZ) seismic behavior,
because of its role in overall ductility and lateral stiffness of steel
moment frames, has been considered a challenge for years. There are
some studies regarding the effects of different doubler plates
thicknesses and geometric properties of PZ on its seismic behavior.
However, there is not much investigation on the effects of number of
provided continuity plates in case of presence of one triangular
haunch, two triangular haunches and rectangular haunch (T shape
haunches) for exterior columns. In this research first detailed finite
element models of 12tested connection of SAC joint venture were
created and analyzed then obtained cyclic behavior backbone curves
of these models besides other FE models for similar tests were used
for neural network training. Then seismic behavior of these data is
categorized according to continuity plate-s arrangements and
differences in type of haunches. PZ with one-sided haunches have
little plastic rotation. As the number of continuity plates increases
due to presence of two triangular haunches (four continuity plate),
there will be no plastic rotation, in other words PZ behaves in its
elastic range. In the case of rectangular haunch, PZ show more plastic
rotation in comparison with one-sided triangular haunch and
especially double-sided triangular haunches. Moreover, the models
that will be presented in case of triangular one-sided and double-
sided haunches and rectangular haunches as a result of this study
seem to have a proper estimation of PZ seismic behavior.
Abstract: Combined experimental and computational analysis of
hygrothermal performance of an interior thermal insulation system
applied on a brick wall is presented in the paper. In the experimental
part, the functionality of the insulation system is tested at simulated
difference climate conditions using a semi-scale device. The
measured temperature and relative humidity profiles are used for the
calibration of computer code HEMOT that is finally applied for a
long-term hygrothermal analysis of the investigated structure.
Abstract: This paper presents performance comparison of three estimation techniques used for peak load forecasting in power systems. The three optimum estimation techniques are, genetic algorithms (GA), least error squares (LS) and, least absolute value filtering (LAVF). The problem is formulated as an estimation problem. Different forecasting models are considered. Actual recorded data is used to perform the study. The performance of the above three optimal estimation techniques is examined. Advantages of each algorithms are reported and discussed.
Abstract: This paper examines many mathematical methods for
molding the hourly price forward curve (HPFC); the model will be
constructed by numerous regression methods, like polynomial
regression, radial basic function neural networks & a furrier series.
Examination the models goodness of fit will be done by means of
statistical & graphical tools. The criteria for choosing the model will
depend on minimize the Root Mean Squared Error (RMSE), using the
correlation analysis approach for the regression analysis the optimal
model will be distinct, which are robust against model
misspecification. Learning & supervision technique employed to
determine the form of the optimal parameters corresponding to each
measure of overall loss. By using all the numerical methods that
mentioned previously; the explicit expressions for the optimal model
derived and the optimal designs will be implemented.
Abstract: An experiment was implemented in a filed in the south of Morocco to evaluate the effects of domestic treated wastewater use for irrigation of amaranth crop under semi-arid conditions. Three varieties (A0020, A0057 & A211) were tested and irrigated using domestic treated wastewater EC1 (0,92 dS/m) as control, EC3 (3dS/m) and EC6 (6dS/m) obtained by adding sea water. In term of growth, an increase of the EC level of applied irrigation water reduced significantly the plant-s height, leaf area, fresh and dry weight measured at vegetative, flowering and maturity stage for all varieties. Even with the application of the EC6, yields were relatively higher in comparison with the once obtained in normal cultivation conditions. A significant accumulation of nitrate, chloride and sodium in soil layers during the crop cycle was noted. The use of treated waste water for its irrigation is proved to be possible. The variety A211 had showed to be less sensitive to salinity stress and it could be more promising its introduction to study area.
Abstract: Falls are the primary cause of accidents in people over
the age of 65, and frequently lead to serious injuries. Since the early
detection of falls is an important step to alert and protect the aging
population, a variety of research on detecting falls was carried out
including the use of accelerators, gyroscopes and tilt sensors. In
exiting studies, falls were detected using an accelerometer with
errors. In this study, the proposed method for detecting falls was to
use two accelerometers to reject wrong falls detection. As falls are
accompanied by the acceleration of gravity and rotational motion, the
falls in this study were detected by using the z-axial acceleration
differences between two sites. The falls were detected by calculating
the difference between the analyses of accelerometers placed on two
different positions on the chest of the subject. The parameters of the
maximum difference of accelerations (diff_Z) and the integration of
accelerations in a defined region (Sum_diff_Z) were used to form the
fall detection algorithm. The falls and the activities of daily living
(ADL) could be distinguished by using the proposed parameters
without errors in spite of the impact and the change in the positions
of the accelerometers. By comparing each of the axial accelerations,
the directions of falls and the condition of the subject afterwards
could be determined.In this study, by using two accelerometers
without errors attached to two sites to detect falls, the usefulness of
the proposed fall detection algorithm parameters, diff_Z and
Sum_diff_Z, were confirmed.
Abstract: Solidification cracking and hydrogen cracking are some defects generated in the fusion welding of ultrahigh carbon steels. However, friction stir welding (FSW) of such steels, being a solid-state technique, has been demonstrated to alleviate such problems encountered in traditional welding. FSW include different process parameters that must be carefully defined prior processing. These parameters included but not restricted to: tool feed, tool RPM, tool geometry, tool tilt angle. These parameters form a key factor behind avoiding warm holes and voids behind the tool and in achieving a defect-free weld. More importantly, these parameters directly affect the microstructure of the weld and hence the final mechanical properties of weld. For that, 3D finite element (FE) thermo-mechanical model was developed using DEFORM 3D to simulate FSW of carbon steel. At points of interest in the joint, tracking is done for history of critical state variables such as temperature, stresses, and strain rates. Typical results found include the ability to simulate different weld zones. Simulations predictions were successfully compared to experimental FSW tests. It is believed that such a numerical model can be used to optimize FSW processing parameters to favor desirable defect free weld with better mechanical properties.
Abstract: Wireless ad hoc nodes are freely and dynamically
self-organize in communicating with others. Each node can act as
host or router. However it actually depends on the capability of
nodes in terms of its current power level, signal strength, number
of hops, routing protocol, interference and others. In this research,
a study was conducted to observe the effect of hops count over
different network topologies that contribute to TCP Congestion
Control performance degradation. To achieve this objective, a
simulation using NS-2 with different topologies have been
evaluated. The comparative analysis has been discussed based on
standard observation metrics: throughput, delay and packet loss
ratio. As a result, there is a relationship between types of topology
and hops counts towards the performance of ad hoc network. In
future, the extension study will be carried out to investigate the
effect of different error rate and background traffic over same
topologies.
Abstract: In this work, we present a comparison between two
techniques of image compression. In the first case, the image is
divided in blocks which are collected according to zig-zag scan. In
the second one, we apply the Fast Cosine Transform to the image,
and then the transformed image is divided in blocks which are
collected according to zig-zag scan too. Later, in both cases, the
Karhunen-Loève transform is applied to mentioned blocks. On the
other hand, we present three new metrics based on eigenvalues for a
better comparative evaluation of the techniques. Simulations show
that the combined version is the best, with minor Mean Absolute
Error (MAE) and Mean Squared Error (MSE), higher Peak Signal to
Noise Ratio (PSNR) and better image quality. Finally, new technique
was far superior to JPEG and JPEG2000.
Abstract: Delayed wound healing in diabetes is primarily
associated with hyperglycemia, over-expression of inflammatory
marker, oxidative stress and delayed collagen synthesis. This
unmanaged wound is producing high economic burden on the
society. Thus research is required to develop new and effective
treatment strategies to deal with this emerging issue. Our present
study incorporates the evaluation of wound healing effects of 50%
ethanol extract of Ocimum sanctum (OSE) in streptozotocin
(45mg/kg)-induced diabetic rats with concurrent wound ulcer. The
animals showing diabetes (Blood glucose level >140 and
Abstract: Effectiveness and efficiency of food distribution is necessary to maintain food security in a region. Food supply varies among regions depending on their production capacity; therefore, it is necessary to regulate food distribution. Sea transportation could play a great role in the food distribution system. To play this role and to support transportation needs in the Eastern Indonesia, sea transportation shall be supported by fleet which is adequate and reliable, both in terms of load and worthiness. This research uses Linear Programming (LP) method to analyze food distribution pattern in order to determine the optimal distribution system. In this research, transshipment points have been selected for regions in one province. Comparison between result of modeling and existing shipping route reveals that from 369 existing routes, 54 routes are used for transporting rice, corn, green bean, peanut, soybean, sweet potato, and cassava.
Abstract: In this paper, a few chattering-free Sliding Mode Controllers (SMC) are proposed to stabilize an Active Magnetic Bearing (AMB) system with gyroscopic effect that is proportional to the rotor speed. The improved switching terms of the controller inherited from the saturation-type function and boundary layer control technique is shown to be able to achieve bounded and asymptotic stability, respectively, while the chattering effect in the input is attenuated. This is proven to be advantageous for AMB system since minimization of chattering results in optimized control effort. The performance of each controller is demonstrated via result of simulation in which the measurement of the total consumed energy and maximum control magnitude of each controller illustrates the effectiveness of the proposed controllers.
Abstract: Service-oriented systems have become popular and
presented many advantages in develop and maintain process. The
coupling is the most important attribute of services when they are
integrated into a system. In this paper, we propose a suite of metrics
to evaluate service-s quality according to its ability of coupling. We
use the coupling metrics to measure the maintainability, reliability,
testability, and reusability of services. Our proposed metrics are
operated in run-time which bring more exact results.
Abstract: The affect of the attendance percentage, the overall
GPA and the number of credit hours the student is enrolled in at
specific semester on the grade attained in specific course has been
studied. This study has been performed on three courses offered in
industrial engineering department at the Hashemite University in
Jordan. Study has revealed that the grade attained by a student is
strongly affected by the attendance percentage and his overall GPA
with a value of R2 of 52.5%. Another model that has been
investigated is the relation between the semester GPA and the
attendance percentage, the number of credit hours enrolled in at
specific semester, and the overall GPA. This model gave us a strong
relationship between the semester GPA and attendance percentage
and the overall GPA with a value of R2 of 76.2%.
Abstract: The Platform Screen Doors improve Indoor Air Quality
(IAQ) in the subway station; however, and the air quality is degraded
in the subway tunnel. CO2 concentration and indoor particulate matter
value are high in the tunnel. The IAQ level in subway tunnel degrades
by increasing the train movements. Air-curtain installation reduces
dusts, particles and moving toxic smokes and permits traffic by
generating virtual wall. The ventilation systems of the subway tunnel
need improvements to have better air-quality. Numerical analyses
might be effective tools analyze the flowfield inside the air-curtain
installed subway tunnel. The ANSYS CFX software is used for steady
computations of the airflow inside the tunnel. The single-track subway
tunnel has the natural shaft, the mechanical shaft, and the PSDs
installed stations. The height and width of the tunnel are 6.0 m and 4.0
m respectively. The tunnel is 400 m long and the air-curtain is installed
at the top of the tunnel. The thickness and the width of the air-curtain
are 0.08 m and 4 m respectively. The velocity of the air-curtain
changes between 20 - 30 m/s. Three cases are analyzed depending on
the installing location of the air-curtain. The discharged-air through
the natural shafts increases as the velocity of the air-curtain increases
when the air-curtain is installed between the mechanical and the
natural shafts. The pollutant-air is exhausted by the mechanical and the
natural shafts and remained air is pushed toward tunnel end. The
discharged-air through the natural shaft is low when the air-curtain
installed before the natural shaft. The mass flow rate decreases in the
tunnel after the mechanical shaft as the air-curtain velocity increases.
The computational results of the air-curtain installed tunnel become
basis for the optimum design study. The air-curtain installing location
is chosen between the mechanical and the natural shafts. The velocity
of the air-curtain is fixed as 25 m/s. The thickness and the blowing
angles of the air-curtain are the design variables for the optimum
design study. The object function of the design optimization is
maximizing the discharged air through the natural shaft.
Abstract: Saturated hydraulic conductivity of Soil is an
important property in processes involving water and solute flow in
soils. Saturated hydraulic conductivity of soil is difficult to measure
and can be highly variable, requiring a large number of replicate
samples. In this study, 60 sets of soil samples were collected at
Saqhez region of Kurdistan province-IRAN. The statistics such as
Correlation Coefficient (R), Root Mean Square Error (RMSE), Mean
Bias Error (MBE) and Mean Absolute Error (MAE) were used to
evaluation the multiple linear regression models varied with number
of dataset. In this study the multiple linear regression models were
evaluated when only percentage of sand, silt, and clay content (SSC)
were used as inputs, and when SSC and bulk density, Bd, (SSC+Bd)
were used as inputs. The R, RMSE, MBE and MAE values of the 50
dataset for method (SSC), were calculated 0.925, 15.29, -1.03 and
12.51 and for method (SSC+Bd), were calculated 0.927, 15.28,-1.11
and 12.92, respectively, for relationship obtained from multiple
linear regressions on data. Also the R, RMSE, MBE and MAE values
of the 10 dataset for method (SSC), were calculated 0.725, 19.62, -
9.87 and 18.91 and for method (SSC+Bd), were calculated 0.618,
24.69, -17.37 and 22.16, respectively, which shows when number of
dataset increase, precision of estimated saturated hydraulic
conductivity, increases.
Abstract: MicroRNAs (miRNAs) are small, non-coding and
regulatory RNAs about 20 to 24 nucleotides long. Their conserved
nature among the various organisms makes them a good source of
new miRNAs discovery by comparative genomics approach. The
study resulted in 21 miRNAs of 20 pre-miRNAs belonging to 16
families (miR156, 157, 158, 164, 165, 168, 169, 172, 319, 390, 393,
394, 395, 400, 472 and 861) in evergreen spruce tree (Picea). The
miRNA families; miR 157, 158, 164, 165, 168, 169, 319, 390, 393,
394, 400, 472 and 861 are reported for the first time in the Picea. All
20 miRNA precursors form stable minimum free energy stem-loop
structure as their orthologues form in Arabidopsis and the mature
miRNA reside in the stem portion of the stem loop structure. Sixteen
(16) miRNAs are from Picea glauca and five (5) belong to Picea
sitchensis. Their targets consist of transcription factors, growth
related, stressed related and hypothetical proteins.
Abstract: In this paper, Selective Adaptive Parallel Interference Cancellation (SA-PIC) technique is presented for Multicarrier Direct Sequence Code Division Multiple Access (MC DS-CDMA) scheme. The motivation of using SA-PIC is that it gives high performance and at the same time, reduces the computational complexity required to perform interference cancellation. An upper bound expression of the bit error rate (BER) for the SA-PIC under Rayleigh fading channel condition is derived. Moreover, the implementation complexities for SA-PIC and Adaptive Parallel Interference Cancellation (APIC) are discussed and compared. The performance of SA-PIC is investigated analytically and validated via computer simulations.
Abstract: The triumph of inductive neuro-stimulation since its rediscovery in the 1980s has been quite spectacular. In lots of branches ranging from clinical applications to basic research this system is absolutely indispensable. Nevertheless, the basic knowledge about the processes underlying the stimulation effect is still very rough and rarely refined in a quantitative way. This seems to be not only an inexcusable blank spot in biophysics and for stimulation prediction, but also a fundamental hindrance for technological progress. The already very sophisticated devices have reached a stage where further optimization requires better strategies than provided by simple linear membrane models of integrate-and-fire style. Addressing this problem for the first time, we suggest in the following text a way for virtual quantitative analysis of a stimulation system. Concomitantly, this ansatz seems to provide a route towards a better understanding by using nonlinear signal processing and taking the nerve as a filter that is adapted for neuronal magnetic stimulation. The model is compact and easy to adjust. The whole setup behaved very robustly during all performed tests. Exemplarily a recent innovative stimulator design known as cTMS is analyzed and dimensioned with this approach in the following. The results show hitherto unforeseen potentials.