Abstract: In this current contribution, authors are dedicated to
investigate influence of the crystal lamellae orientation on
electromechanical behaviors of relaxor ferroelectric Poly
(vinylidene fluoride –trifluoroethylene -chlorotrifluoroethylene)
(P(VDF-TrFE-CTFE)) films by control of polymer microstructure,
aiming to picture the full map of structure-property relationship. In
order to define their crystal orientation films, terpolymer films were
fabricated by solution-casting, stretching and hot-pressing process.
Differential scanning calorimetry, impedance analyzer, and tensile
strength techniques were employed to characterize crystallographic
parameters, dielectric permittivity, and elastic Young’s modulus
respectively. In addition, large electrical induced out-of-plane
electrostrictive strain was obtained by cantilever beam mode.
Consequently, as-casted pristine films exhibited surprisingly high
electrostrictive strain 0.1774% due to considerably small value of
elastic Young’s modulus although relatively low dielectric
permittivity. Such reasons contributed to large mechanical elastic
energy density. Instead, due to 2 folds increase of elastic Young’s
modulus and less than 50% augmentation of dielectric constant, fullycrystallized
film showed weak electrostrictive behavior and
mechanical energy density as well. And subjected to mechanical
stretching process, Film C exhibited stronger dielectric constant and
out-performed electrostrictive strain over Film B because edge-on
crystal lamellae orientation induced by uniaxially mechanical stretch.
Hot-press films were compared in term of cooling rate. Rather large
electrostrictive strain of 0.2788% for hot-pressed Film D in
quenching process was observed although its dielectric permittivity
equivalent to that of pristine as-casted Film A, showing highest
mechanical elastic energy density value of 359.5 J/m3. In hot-press
cooling process, dielectric permittivity of Film E saw values at 48.8
concomitant with ca.100% increase of Young’s modulus. Films with
intermediate mechanical energy density were obtained.
Abstract: In order to study the Mutual effect of genotype ×
environment for the percent of oil index in sunflower items, an
experiment was accomplished form complete random block designs
in four iteration and was four diverse researching station comprising
Esfahan, Birjand, Sari, and Karaj. Complex variance analysis showed
that there is an important diversity between the items under
investigation. The results relevant the coefficient variation of items
Azargol and Vidoc has respectively allocated the minimum
coefficient of variations. According to the results extrapolated from
Shokla stability variance, the Items Brocar, Allison and Fabiola, are
among the stable genotypes for oil percent respectively. In the biplot
GGE, the location under investigations divided in two superenvironments,
first one comprised of locations naming Esfahan,
Karaj, and Birjand, and second one were such a location as Sari. By
this point of view, in the first super-environment, the Item Fabiola
and in the second Almanzor item was among the best items and
crops.
Abstract: This paper explored the challenges faced by the
management of a Ghanaian state enterprise in managing conflicts and
disturbances associated with its attempt to implement new work
practices to enhance its capability to operate as a commercial entity.
The purpose was to understand the extent to which organizational
involvement, consistency and adaptability influence employees’
consumption of new work practices in transforming the
organization’s organizational activity system. Using selfadministered
questionnaires, data were collected from one hundred
and eighty (180) employees and analyzed using both descriptive and
inferential statistics. The results showed that constraints in
organizational involvement and adaptability prevented the positive
consumption of new work practices by employees in the
organization. It is also found that the organization’s employees failed
to consume the new practices being implemented, because they
perceived the process as non-involving, and as such, did not
encourage the development of employee capability, empowerment,
and teamwork. The study concluded that the failure of the
organization’s management to create opportunities for organizational
learning constrained its ability to get employees consume the new
work practices, which situation could have facilitated the
organization’s capabilities of operating as a commercial entity.
Abstract: Fermentation is well known as an essential process to
develop chocolate flavor in dried cocoa beans. Besides developing
the precursor of cocoa flavor, it also induces the color changes in the
beans. The fermentation process is influenced by various factors such
as planting material, preconditioning of cocoa pod and fermentation
technique. Therefore, this study was conducted to evaluate color of
Malaysian cocoa beans and how the duration of pods storage and
fermentation technique using shallow box will effect on its color
characteristics. There are two factors being studied i.e. duration of
cocoa pod storage (0, 2, 4 and 6 days) and duration of cocoa
fermentation (0, 1, 2, 3, 4 and 5 days). The experiment is arranged in
4 x 6 factorial designs with 24 treatments and arrangement is in a
Completely Randomised Design (CRD). The produced beans are
inspected for color changes under artificial light during cut test and
divided into four groups of color namely fully brown, purple brown,
fully purple and slaty. Cut tests indicated that cocoa beans which are
directly dried without undergone fermentation has the highest slaty
percentage. However, application of pods storage before fermentation
process is found to decrease the slaty percentage. In contrast, the
percentages of fully brown beans start to dominate after two days of
fermentation, especially from four and six days of pods storage batch.
Whereas, almost all batches of cocoa beans have a percentage of fully
purple less than 20%. Interestingly, the percentage of purple brown
beans are scattered in the entire beans batch regardless any specific
trend. Meanwhile, statistical analysis using General Linear Model
showed that the pods storage has a significant effect on the color
characteristic of the Malaysian dried beans compared to fermentation
duration.
Abstract: The field of instrumentation electronics is undergoing
an explosive growth, due to its wide range of applications. The
proliferation of electrical devices in a close working proximity can
negatively influence each other’s performance. The degradation in
the performance is due to electromagnetic interference (EMI). This paper investigates the negative effects of electromagnetic
interference originating in the General Purpose Interface Bus (GPIB)
control-network of the AC-DC transfer measurement system.
Remedial measures of reducing measurement errors and failure of
range of industrial devices due to EMI have been explored. The ACDC
transfer measurement system was analysed for the commonmode
(CM) EMI effects. Further investigation of coupling path as
well as much accurate identification of noise propagation mechanism
has been outlined. To prevent the occurrence of common-mode
(ground loops) which was identified between the GPIB system
control circuit and the measurement circuit, a microcontroller-driven
GPIB switching isolator device was designed, prototyped,
programmed and validated. This mitigation technique has been
explored to reduce EMI effectively.
Abstract: Earth structures constructed of marine clay soils have
tendency to crack. In order to improve the flexural strength and
brittleness, a technique of mixing short fibers is introduced to the soil
lime mixture. Coir fiber was used in this study as reinforcing
elements. An experimental investigation consisting primarily of
flexural tensile tests was conducted to examine the influence of coir
fibers on the flexural behaviour of the reinforced soils. The test
results that the coir fibers were effective in improving the flexural
strength and Young’s modulus of all soils examined and ductility
after peak strength for reinforced marine clay soil treated by lime. 5%
lime treated soil and 1% coir fiber reinforced soil specimens’
demonstrated good strength and durability when submerged in water
and retained 45% of their air-cured strengths.
Abstract: The aim of this study is to examine, through
experimentation in the laboratory, the supercritical flow in the
presence of an obstacle in a rectangular channel. The supercritical
regime in the whole hydraulic channel is achieved by adding a
convergent. We will observe the influence of the obstacle shape and
dimension on the characteristics of the supercritical flow, mainly the
free-surface elevation and the velocity profile. The velocity
measurements have been conducted with the one dimension laser
anemometry technique.
Abstract: Bottom ash from Municipal Solid Waste Incineration
(MSWI) can be viewed as a typical granular material because these
industrial by-products result from the incineration of various
domestic wastes. MSWI bottom ash is mainly used in road
engineering in substitution of the traditional natural aggregates. As
the characterization of their mechanical behavior is essential in order
to use them, specific studies have been led over the past few years. In
the first part of this paper, the mechanical behavior of MSWI bottom
ash is studied with triaxial tests. After, analysis of the experiment
results, the simulation of triaxial tests is carried out by using the
software package CESAR-LCPC. As the first approach in modeling
of this new class material, the Mohr-Coulomb model was chosen to
describe the evolution of material under the influence of external
mechanical actions.
Abstract: Hard coatings are widely used in cutting and forming
tool industries. Titanium Nitride (TiN) possesses good hardness,
strength, and corrosion resistance. The coating properties are
influenced by many process parameters. The coatings were deposited
on steel substrate by changing the process parameters such as
substrate temperature, nitrogen flow rate and target power in a D.C
planer magnetron sputtering. The structure of coatings were analysed
using XRD. The hardness of coatings was found using Micro
hardness tester. From the experimental data, a regression model was
developed and the optimum response was determined using Response
Surface Methodology (RSM).
Abstract: The purpose of this study is to analyze the temporal
and spatial variability of thermal conditions in the Republic of
Armenia. The paper describes annual fluctuations in air temperature.
Research has been focused on case study region of Armenia and
surrounding areas, where long–term measurements and observations
of weather conditions have been performed within the National
Meteorological Service of Armenia and its surrounding areas. The
study contains yearly air temperature data recorded between 1961-
2012. Mann-Kendal test and the autocorrelation function were
applied to detect the change trend of annual mean temperature, as
well as other parametric and non-parametric tests searching to find
the presence of some breaks in the long term evolution of
temperature. The analysis of all records reveals a tendency mostly
towards warmer years, with increased temperatures especially in
valleys and inner basins. The maximum temperature increase is up to
1,5°C. Negative results have not been observed in Armenia. The
patterns of temperature change have been observed since the 1990’s
over much of the Armenian territory. The climate in Armenia was
influenced by global change in the last 2 decades, as results from the
methods employed within the study.
Abstract: River Hindon is an important river catering the
demand of highly populated rural and industrial cluster of western
Uttar Pradesh, India. Water quality of river Hindon is deteriorating at
an alarming rate due to various industrial, municipal and agricultural
activities. The present study aimed at identifying the pollution
sources and quantifying the degree to which these sources are
responsible for the deteriorating water quality of the river. Various
water quality parameters, like pH, temperature, electrical
conductivity, total dissolved solids, total hardness, calcium, chloride,
nitrate, sulphate, biological oxygen demand, chemical oxygen
demand, and total alkalinity were assessed. Water quality data
obtained from eight study sites for one year has been subjected to the
two multivariate techniques, namely, principal component analysis
and cluster analysis. Principal component analysis was applied with
the aim to find out spatial variability and to identify the sources
responsible for the water quality of the river. Three Varifactors were
obtained after varimax rotation of initial principal components using
principal component analysis. Cluster analysis was carried out to
classify sampling stations of certain similarity, which grouped eight
different sites into two clusters. The study reveals that the
anthropogenic influence (municipal, industrial, waste water and
agricultural runoff) was the major source of river water pollution.
Thus, this study illustrates the utility of multivariate statistical
techniques for analysis and elucidation of multifaceted data sets,
recognition of pollution sources/factors and understanding
temporal/spatial variations in water quality for effective river water
quality management.
Abstract: Over the last two decades, externally bonded fiber
reinforced polymer (FRP) composites bonded to concrete substrates
has become a popular method for strengthening reinforced concrete
(RC) highway and railway bridges. Such structures are exposed to
severe cyclic loading throughout their lifetime often resulting in
fatigue damage to structural components and a reduction in the
service life of the structure. Since experimental and numerical results
on the fatigue performance of FRP-to-concrete joints are still limited,
the current research focuses on assessing the fatigue performance of
externally bonded FRP-to-concrete joints using a direct shear test.
Some early results indicate that the stress ratio and the applied cyclic
stress level have a direct influence on the fatigue life of the externally
bonded FRP. In addition, a calibrated finite element model is
developed to provide further insight into the influence of certain
parameters such as: concrete strength, FRP thickness, number of
cycles, frequency, and stiffness on the fatigue life of the FRP-toconcrete
joints.
Abstract: English like any other language is rich by means of arbitrary, conventional, symbols which lend it to lot of inconsistencies in spelling, phonology, syntax, and morphology. The research examines the irregularities prevalent in the structure and meaning of some ‘er’ lexical items in English and its implication to vocabulary acquisition. It centers its investigation on the derivational suffix ‘er’, which changes the grammatical category of word. English language poses many challenges to Second Language Learners because of its irregularities, exceptions, and rules. One of the meaning of –er derivational suffix is someone or somebody who does something. This rule often confuses the learners when they meet with the exceptions in normal discourse. The need to investigate instances of such inconsistencies in the formation of –er words and the meanings given to such words by the students motivated this study. For this purpose, some senior secondary two (SS2) students in six randomly selected schools in the metropolis were provided a large number of alphabetically selected ‘er’ suffix ending words, The researcher opts for a test technique, which requires them to provide the meaning of the selected words with- er. The marking of the test was scored on the scale of 1-0, where correct formation of –er word and meaning is scored one while wrong formation and meaning is scored zero. The number of wrong and correct formations of –er words meaning were calculated using percentage. The result of this research shows that a large number of students made wrong generalization of the meaning of the selected -er ending words. This shows how enormous the inconsistencies are in English language and how are affect the learning of English. Findings from the study revealed that though students mastered the basic morphological rules but the errors are generally committed on those vocabulary items that are not frequently in use. The study arrives at this conclusion from the survey of their textbook and their spoken activities. Therefore, the researcher recommends that there should be effective reappraisal of language teaching through implementation of the designed curriculum to reflect on modern strategies of teaching language, identification, and incorporation of the exceptions in rigorous communicative activities in language teaching, language course books and tutorials, training and retraining of teachers on the strategies that conform to the new pedagogy.
Abstract: A Friction stir welding tool is a critical component to
the success of the process. The tool typically consists of a rotating
round shoulder and a threaded cylindrical pin that heats the work
piece, mostly by friction, and moves the softened alloy around it to
form the joint. In this research work, an attempt has been made to
investigate the relationship between FSW variables mainly tool
profile, rotating speed, welding speed and the mechanical properties
(tensile strength, yield strength, percentage elongation, and micro
hardness) of friction stir welded aluminum alloy 5083 joints. From
the experimental details, it can be assessed that the joint produced by
using Triflute profile tool has contribute superior mechanical and
structural properties as compared to Tapered unthreaded & Threaded
tool for 1000rpm.
Abstract: In this paper, a prototype PEM fuel cell vehicle
integrated with a 1 kW air-blowing proton exchange membrane fuel
cell (PEMFC) stack as a main power sources has been developed for
a lightweight cruising vehicle. The test vehicle is equipped with a
PEM fuel cell system that provides electric power to a brushed DC
motor. This vehicle was designed to compete with industrial
lightweight vehicle with the target of consuming least amount of
energy and high performance. Individual variations in driving style
have a significant impact on vehicle energy efficiency and it is well
established from the literature. The primary aim of this study was to
assesses the power and fuel consumption of a hydrogen fuel cell
vehicle operating at three difference driving technique (i.e. 25 km/h
constant speed, 22-28 km/h speed range, 20-30 km/h speed range).
The goal is to develop the best driving strategy to maximize
performance and minimize fuel consumption for the vehicle system.
The relationship between power demand and hydrogen consumption
has also been discussed. All the techniques can be evaluated and
compared on broadly similar terms. Automatic intelligent controller
for driving prototype fuel cell vehicle on different obstacle while
maintaining all systems at maximum efficiency was used. The result
showed that 25 km/h constant speed was identified for optimal
driving with less fuel consumption.
Abstract: The research investigates the causes of unemployment
in Namibia, Nigeria and South Africa and the role of Capital
Accumulation in reducing the unemployment profile of these
economies as proposed by the post-Keynesian economics. This is
conducted through extensive review of literature on the NAIRU
models and focused on the post-Keynesian view of unemployment
within the NAIRU framework. The NAIRU (non-accelerating
inflation rate of unemployment) model has become a dominant
framework used in macroeconomic analysis of unemployment. The
study views the post-Keynesian economics arguments that capital
accumulation is a major determinant of unemployment.
Unemployment remains the fundamental socio-economic challenge
facing African economies. It has been a burden to citizens of those
economies. Namibia, Nigeria, and South Africa are great African
nations battling with high unemployment rates. The high
unemployment rate in the country led the citizens to chase away
foreigners in the country claiming that they have taken away their
jobs. The study proposes there is a strong relationship between
capital accumulation and unemployment in Namibia, Nigeria, and
South Africa, and capital accumulation is responsible for high
unemployment rates in these countries. For the economies to achieve
steady state level of employment and satisfactory level of economic
growth and development, there is need for capital accumulation to
take place. The countries in the study have been selected after a
critical research and investigations. They are selected based on the
following criteria; African economies with high unemployment rates
above 15% and have about 40% of their workforce unemployed. This
level of unemployment is the critical level of unemployment in
Africa as expressed by International Labour Organization (ILO). And
finally, the African countries experience a slow growth in their Gross
fixed capital formation. Adequate statistical measures have been
employed using a time-series analysis in the study and the results
revealed that capital accumulation is the main driver of
unemployment performance in the chosen African countries. An
increase in the accumulation of capital causes unemployment to
reduce significantly. The results of the research work will be useful
and relevant to federal governments and ministries, departments and
agencies (MDAs) of Namibia, Nigeria and South Africa to resolve
the issue of high and persistent unemployment rates in their
economies which are great burden that slows growth and
development of developing economies. Also, the result can be useful
to World Bank, African Development Bank and International Labour
Organization (ILO) in their further research and studies on how to
tackle unemployment in developing and emerging economies.
Abstract: The strain intensity and redundant strains, dependent
in multistage TRIP wire drawing processes from values used single
partial reductions, should influence on the intensity of transformation
the retained austenite into martensite and thereby on mechanical
properties of drawn wires. The numerical analysis of drawing
processes with use of Drawing 2D programme, for steel wires made
from TRIP steel with 0,29% has been shown in the work. The change
of strain intensity εc and the values of redundant strain εxy, has been
determined for particular draws in dependence of used single partial
reductions.
Abstract: Social networking sites such as Twitter and Facebook
attracts over 500 million users across the world, for those users, their
social life, even their practical life, has become interrelated. Their
interaction with social networking has affected their life forever.
Accordingly, social networking sites have become among the main
channels that are responsible for vast dissemination of different kinds
of information during real time events. This popularity in Social
networking has led to different problems including the possibility of
exposing incorrect information to their users through fake accounts
which results to the spread of malicious content during life events.
This situation can result to a huge damage in the real world to the
society in general including citizens, business entities, and others. In this paper, we present a classification method for detecting the
fake accounts on Twitter. The study determines the minimized set of
the main factors that influence the detection of the fake accounts on
Twitter, and then the determined factors are applied using different
classification techniques. A comparison of the results of these
techniques has been performed and the most accurate algorithm is
selected according to the accuracy of the results. The study has been
compared with different recent researches in the same area; this
comparison has proved the accuracy of the proposed study. We claim
that this study can be continuously applied on Twitter social network
to automatically detect the fake accounts; moreover, the study can be
applied on different social network sites such as Facebook with minor
changes according to the nature of the social network which are
discussed in this paper.
Abstract: Customer’ needs, quality, and value creation while
reducing costs through supply chain management provides challenges
and opportunities for companies and researchers. In the light of these
challenges, modern ideas must contribute to counter these challenges
and exploit opportunities. Therefore, this paper discusses the impact
of the quality cost on revenue sharing as a most important incentive
to configure business networks. This paper develops the quality cost approach to align with the
modern era. It develops a model to measure quality costs which
might enable firms to manage revenue sharing in a supply chain. The
developed model includes five categories; besides the well-known
four categories (namely prevention costs, appraisal costs, internal
failure costs, and external failure costs), a new category has been
developed in this research as a new vision of the relationship between
quality costs and innovations in industry. This new category is
Recycle Cost. This paper also examines whether such quality costs in
supply chains influence the revenue sharing between partners. Using the author's quality cost model, the relationship between
quality costs and revenue sharing among partners is examined using a
case study in an Egyptian manufacturing company which is a part of
a supply chain. This paper argues that the revenue-sharing proportion
allocated to supplier increases as the recycle cost of supplier
increases, and the revenue-sharing proportion allocated to
manufacturer increases as the prevention and appraisal costs increase,
as well as the failure costs, the recycle costs of manufacturer, and the
recycle costs of suppliers decrease. However, the results present
surprising findings. The purposes of this study are developing quality cost approach
and understanding the relationships between quality costs and
revenue sharing in supply chains. Therefore, the present study
contributes to theory and practice by explaining how the cost of
recycling can be combined in quality cost model to better
understanding the revenue sharing among partners in supply chains.
Abstract: This paper presents numerical analysis in terms of
buckling resistance of GFRP sandwich infill panels system under the
influence of increased temperature on the foam core. Failure mode
under in-plane compression is studied by means of numerical analysis
with ABAQUS platform. Parameters considered in this study are
contact length and both the type of foam for core and the variation of
its module elastic under the thermal influence. Increment of
temperature is considered in static cases and only applied to core.
Indeed, it is proven that the effect of temperature alters the mechanical
properties of the entire panel system. Moreover, the rises of
temperature result in a decrease in strength of the panel. This is due to
the polymeric nature of this material. Additionally, the contact length
also displays the effect on performance of infill panel. Their
significance factors are based on type of polymer for core. Therefore,
by comparing difference type of core material, the variation can be
reducing.