Abstract: In this study, effects of EGR on CO and HC emissions
of a dual fuel HCCI-DI engine are investigated. Tests were
conducted on a single-cylinder variable compression ratio (VCR)
diesel engine with compression ratio of 17.5. Premixed gasoline is
provided by a carburetor connected to intake manifold and equipped
with a screw to adjust premixed air-fuel ratio, and diesel fuel is
injected directly into the cylinder through an injector at pressure of
250 bars. A heater placed at inlet manifold is used to control the
intake charge temperature. Optimal intake charge temperature was
110-115ºC due to better formation of a homogeneous mixture
causing HCCI combustion. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge in HCCI combustion.
Experiments indicated 35 BTDC as the optimum injection timing.
Coolant temperature was maintained 50ºC during the tests. Results
show that increasing engine speed at a constant EGR rate leads to
increase in CO and UHC emissions due to the incomplete
combustion caused by shorter combustion duration and less
homogeneous mixture. Results also show that increasing EGR
reduces the amount of oxygen and leads to incomplete combustion
and therefore increases CO emission due to lower combustion
temperature. HC emission also increases as a result of lower
combustion temperatures.
Abstract: Two-interconnected fluidized bed systems are widely used in various processes such as Fisher-Tropsch, hot gas desulfurization, CO2 capture-regeneration with dry sorbent, chemical-looping combustion, sorption enhanced steam methane reforming, chemical-looping hydrogen generation system, and so on. However, most of two-interconnected fluidized beds systems require riser and/or pneumatic transport line for solid conveying and loopseals or seal-pots for gas sealing, recirculation of solids to the riser, and maintaining of pressure balance. The riser (transport bed) is operated at the high velocity fluidization condition and residence times of gas and solid in the riser are very short. If the reaction rate of catalyst or sorbent is slow, the riser can not ensure sufficient contact time between gas and solid and we have to use two bubbling beds for each reaction to ensure sufficient contact time. In this case, additional riser must be installed for solid circulation. Consequently, conventional two-interconnected fluidized bed systems are very complex, large, and difficult to operate. To solve these problems, a novel two-interconnected fluidized bed system has been developed. This system has two bubbling beds, solid injection nozzles, solid conveying lines, and downcomers. In this study, effects of operating variables on solid circulation rate, gas leakage between two beds have been investigated in a cold mode two-interconnected fluidized bed system. Moreover, long-term operation of continuous solid circulation up to 60 hours has been performed to check feasibility of stable operation.
Abstract: This paper presents the design, fabrication and
evaluation of magneto-rheological damper. Semi-active control
devices have received significant attention in recent years because
they offer the adaptability of active control devices without requiring
the associated large power sources. Magneto-Rheological (MR)
dampers are semi- active control devices that use MR fluids to
produce controllable dampers. They potentially offer highly reliable
operation and can be viewed as fail-safe in that they become passive
dampers if the control hardware malfunction. The advantage of MR
dampers over conventional dampers are that they are simple in
construction, compromise between high frequency isolation and
natural frequency isolation, they offer semi-active control, use very
little power, have very quick response, has few moving parts, have a
relax tolerances and direct interfacing with electronics. Magneto-
Rheological (MR) fluids are Controllable fluids belonging to the
class of active materials that have the unique ability to change
dynamic yield stress when acted upon by an electric or magnetic
field, while maintaining viscosity relatively constant. This property
can be utilized in MR damper where the damping force is changed by
changing the rheological properties of the fluid magnetically. MR
fluids have a dynamic yield stress over Electro-Rheological fluids
(ER) and a broader operational temperature range. The objective of
this papert was to study the application of an MR damper to vibration
control, design the vibration damper using MR fluids, test and
evaluate its performance. In this paper the Rheology and the theory
behind MR fluids and their use on vibration control were studied.
Then a MR vibration damper suitable for vehicle suspension was
designed and fabricated using the MR fluid. The MR damper was
tested using a dynamic test rig and the results were obtained in the
form of force vs velocity and the force vs displacement plots. The
results were encouraging and greatly inspire further research on the
topic.
Abstract: This work presents the experimental results obtained
at a pilot plant which works with a slow, wet and catalytic pyrolysis
process of dry fowl manure. This kind of process mainly consists in
the cracking of the organic matrix and in the following reaction of
carbon with water, which is either already contained in the organic
feed or added, to produce carbon monoxide and hydrogen. Reactions
are conducted in a rotating reactor maintained at a temperature of
500°C; the required amount of water is about 30% of the dry organic
feed. This operation yields a gas containing about 59% (on a volume
basis) of hydrogen, 17% of carbon monoxide and other products such
as light hydrocarbons (methane, ethane, propane) and carbon
monoxide in lesser amounts. The gas coming from the reactor can be
used to produce not only electricity, through internal combustion
engines, but also heat, through direct combustion in industrial
boilers. Furthermore, as the produced gas is devoid of both solid
particles and pollutant species (such as dioxins and furans), the
process (in this case applied to fowl manure) can be considered as an
optimal way for the disposal and the contemporary energetic
valorization of organic materials, in such a way that is not damaging
to the environment.
Abstract: Universities have an important role in social education in many aspects. In terms of creating awareness and convincing public about social issues, universities take a leading position for public. The best way to provide public support for social education is to develop public communication campaigns. The aim of this study is to present a public communication model which will be guided in social education practices. The study titled “Importance of public communication campaigns and art activities in Social Education “is based on the following topics: Effects of public communication campaigns on social education, Public relations techniques for education, communication strategies, Steps of public relations campaigns in social education, making persuasive messages for public communication campaigns, developing artistic messages and organizing art activities in social education. In addition to these topics, media planning for social education, forming a team as campaign managers, dialogues with opinion leaders in education and preparing creative communication models for social education will be taken into consideration. This study also aims to criticize social education Case studies in Turkey. At the same time, some communicative methods and principles will be given in the light of communication campaigns within the context of this notice.
Abstract: In metal cutting industries, mathematical/statistical
models are typically used to predict tool replacement time. These
off-line methods usually result in less than optimum replacement
time thereby either wasting resources or causing quality problems.
The few online real-time methods proposed use indirect measurement
techniques and are prone to similar errors. Our idea is based on
identifying the optimal replacement time using an electronic nose to
detect the airborne compounds released when the tool wear reaches
to a chemical substrate doped into tool material during the
fabrication. The study investigates the feasibility of the idea, possible
doping materials and methods along with data stream mining
techniques for detection and monitoring different phases of tool
wear.
Abstract: The composite materials were prepared by sawdust, cassava starch and natural rubber latex (NR). The mixtures of 15%w/v gelatinized cassava starch and 15%w/v PVOH were used as the binder of these composite materials. The concentrated rubber latex was added to the mixtures. They were mixed rigorously to the treated sawdust in the ratio of 70:30 until achive uniform dispersion. The batters were subjected to the hot compression moulding at the temperature of 160°C and 3,000 psi pressure for 5 min. The experimental results showed that the mechanical properties of composite materials, which contained the gelatinized cassava starch and PVOH in the ratio of 2:1, 20% NR latex by weight of the dry starch and treated sawdust with 5%NaOH or 1% BPO, were the best. It contributed the maximal compression strength (341.10 + 26.11 N), puncture resistance (8.79 + 0.98 N/mm2) and flexural strength (3.99 + 0.72N/mm2). It is also found that the physicochemical and mechanical properties of composites strongly depends on the interface quality of sawdust, cassava starch and NR latex.
Abstract: The Petri net tool INA is a well known tool by the
Petri net community. However, it lacks a graphical environment to
cerate and analyse INA models. Building a modelling tool for the
design and analysis from scratch (for INA tool for example) is
generally a prohibitive task. Meta-Modelling approach is useful to
deal with such problems since it allows the modelling of the
formalisms themselves. In this paper, we propose an approach based
on the combined use of Meta-modelling and Graph Grammars to
automatically generate a visual modelling tool for INA for analysis
purposes. In our approach, the UML Class diagram formalism is
used to define a meta-model of INA models. The meta-modelling
tool ATOM3 is used to generate a visual modelling tool according to
the proposed INA meta-model. We have also proposed a graph
grammar to automatically generate INA description of the
graphically specified Petri net models. This allows the user to avoid
the errors when this description is done manually. Then the INA tool
is used to perform the simulation and the analysis of the resulted INA
description. Our environment is illustrated through an example.
Abstract: This paper describes part of a project about Learningby-
Modeling (LbM). Studying complex systems is increasingly
important in teaching and learning many science domains. Many
features of complex systems make it difficult for students to develop
deep understanding. Previous research indicates that involvement
with modeling scientific phenomena and complex systems can play a
powerful role in science learning. Some researchers argue with this
view indicating that models and modeling do not contribute to
understanding complexity concepts, since these increases the
cognitive load on students. This study will investigate the effect of
different modes of involvement in exploring scientific phenomena
using computer simulation tools, on students- mental model from the
perspective of structure, behavior and function. Quantitative and
qualitative methods are used to report about 121 freshmen students
that engaged in participatory simulations about complex phenomena,
showing emergent, self-organized and decentralized patterns. Results
show that LbM plays a major role in students' concept formation
about complexity concepts.
Abstract: Optimization of cutting parameters important in precision machining in regards to efficiency and surface integrity of the machined part. Usually productivity and precision in machining is limited by the forces emanating from the cutting process. Due to the inherent varying nature of the workpiece in terms of geometry and material composition, the peak cutting forces vary from point to point during machining process. In order to increase productivity without compromising on machining accuracy, it is important to control these cutting forces. In this paper a fuzzy logic control algorithm is developed that can be applied in the control of peak cutting forces in milling of spherical surfaces using ball end mills. The controller can adaptively vary the feedrate to maintain allowable cutting force on the tool. This control algorithm is implemented in a computer numerical control (CNC) machine. It has been demonstrated that the controller can provide stable machining and improve the performance of the CNC milling process by varying feedrate.
Abstract: The Yasuj city stream named the Beshar supply
water for different usages such as aquaculture farms , drinking,
agricultural and industrial usages. Fish processing plants
,Agricultural farms, waste water of industrial zones and hospitals
waste water which they are generate by human activity produce a
considerable volume of effluent and when they are released in to the
stream they can effect on the water quality and down stream aquatic
systems. This study was conducted to evaluate the effects of outflow
effluent from different human activity and point and non point
pollution sources on the water quality and health of the Beshar
river next to Yasuj. Yasuj is the biggest and most important city in
the Kohkiloye and Boyerahmad province . The Beshar River is one
of the most important aquatic ecosystems in the upstream of the
Karun watershed in south of Iran which is affected by point and non
point pollutant sources . This study was done in order to evaluate the
effects of human activities on the water quality and health of the
Beshar river. This river is approximately 190 km in length and
situated at the geographical positions of 51° 20' to 51° 48' E and 30°
18' to 30° 52' N it is one of the most important aquatic ecosystems of
Kohkiloye and Boyerahmad province in south-west Iran. In this
research project, five study stations were selected to examine water
pollution in the Beshar River systems. Human activity is now one of
the most important factors affecting on hydrology and water quality
of the Beshar river. Humans use large amounts of resources to sustain
various standards of living, although measures of sustainability are
highly variable depending on how sustainability is defined. The
Beshar river ecosystems are particularly sensitive and vulnerable to
human activities. The water samples were analyzed, then some
important water quality parameters such as pH, dissolve oxygen
(DO), Biochemical Oxygen Demand (BOD5), Chemical Oxygen
Demand (COD), Total Suspended Solids (TDS),Turbidity,
Temperature, Nitrates (NO3) and Phosphates (PO4) were estimated
at the two stations. The results show a downward trend in the water
quality at the down stream of the city. The amounts of
BOD5,COD,TSS,T,Turbidity, NO3 and PO4 in the down stream
stations were considerably more than the station 1. By contrast the
amounts of DO in the down stream stations were less than to the
station 1. However when effluent discharge consequence of human
activities are released into the Beshar river near the city, the quality
of river are decreases and the environmental problems of the river
during the next years are predicted to rise.
Abstract: The primary objective of this paper was to construct a
“kinematic parameter-independent modeling of three-axis machine
tools for geometric error measurement" technique. Improving the
accuracy of the geometric error for three-axis machine tools is one of
the machine tools- core techniques. This paper first applied the
traditional method of HTM to deduce the geometric error model for
three-axis machine tools. This geometric error model was related to the
three-axis kinematic parameters where the overall errors was relative
to the machine reference coordinate system. Given that the
measurement of the linear axis in this model should be on the ideal
motion axis, there were practical difficulties. Through a measurement
method consolidating translational errors and rotational errors in the
geometric error model, we simplified the three-axis geometric error
model to a kinematic parameter-independent model. Finally, based on
the new measurement method corresponding to this error model, we
established a truly practical and more accurate error measuring
technique for three-axis machine tools.
Abstract: The purpose of this paper is to present the fuzzy contraction
properties of the Hutchinson-Barnsley operator on the fuzzy
hyperspace with respect to the Hausdorff fuzzy metrics. Also we
discuss about the relationships between the Hausdorff fuzzy metrics
on the fuzzy hyperspaces. Our theorems generalize and extend some
recent results related with Hutchinson-Barnsley operator in the metric
spaces.
Abstract: Adopting the measured constitutive relationship of
stress-strain of river ice, the finite element analysis model of
percussive force of river ice and pier is established, by the explicit
dynamical analysis software package LS-DYNA. Effects of element
types, contact method and arithmetic of ice and pier, coupled modes
between different elements, mesh density of pier, and ice sheet in
contact area on the collision force are studied. Some of measures for
the collision force analysis of river ice and pier are proposed as
follows: bridge girder can adopt beam161 element with 3-node; pier
below the line of 1.30m above ice surface and ice sheet use solid164
element with 8-node; in order to accomplish the connection of
different elements, the rigid body with 0.01-0.05m thickness is defined
between solid164 and beam161; the contact type of ice and pier adopts
AUTOMATIC_SURFACE_TO_SURFACE, using symmetrical
penalty function algorithms; meshing size of pier below the line of
1.30m above ice surface should not less than 0.25×0.25×0.5m3. The
simulation results have the advantage of high precision by making a
comparison between measured and computed data. The research
results can be referred for collision force study between river ice and
pier.
Abstract: Shadows add great amount of realism to a scene and
many algorithms exists to generate shadows. Recently, Shadow
volumes (SVs) have made great achievements to place a valuable
position in the gaming industries. Looking at this, we concentrate on
simple but valuable initial partial steps for further optimization in SV
generation, i.e.; model simplification and silhouette edge detection
and tracking. Shadow volumes (SVs) usually takes time in generating
boundary silhouettes of the object and if the object is complex then
the generation of edges become much harder and slower in process.
The challenge gets stiffer when real time shadow generation and
rendering is demanded. We investigated a way to use the real time
silhouette edge detection method, which takes the advantage of
spatial and temporal coherence, and exploit the level-of-details
(LOD) technique for reducing silhouette edges of the model to use
the simplified version of the model for shadow generation speeding
up the running time. These steps highly reduce the execution time of
shadow volume generations in real-time and are easily flexible to any
of the recently proposed SV techniques. Our main focus is to exploit
the LOD and silhouette edge detection technique, adopting them to
further enhance the shadow volume generations for real time
rendering.
Abstract: WOLED is widely used as lighting for high efficacy and little power consumption. In this research, power factor testing between WOLED and fluorescent lamp to see which one is more efficient in consuming energy. Since both lamps use semiconductor components, so calculation of the power factor need to consider the effects of harmonics. Harmonic make bigger losses. The study is conducted by comparing the value of the power factor regardless of harmonics (DPF) and also by included the harmonics (TPF). The average value of DPF of fluorescent is 0.953 while WOLED is 0.972. The average value of TPF of fluorescent is 0.717 whereas WOLED is 0.933. So from the review of power factor WOLED is more energy efficient than fluorescent lamp.
Abstract: Pressures for urban redevelopment are intensifying in
all large cities. A new logic for urban development is required –
green urbanism – that provides a spatial framework for directing
population and investment inwards to brownfields and greyfields
precincts, rather than outwards to the greenfields. This represents
both a major opportunity and a major challenge for city planners in
pluralist liberal democracies. However, plans for more compact
forms of urban redevelopment are stalling in the face of community
resistance. A new paradigm and spatial planning platform is required
that will support timely multi-level and multi-actor stakeholder
engagement, resulting in the emergence of consensus plans for
precinct-level urban regeneration capable of more rapid
implementation. Using Melbourne, Australia as a case study, this
paper addresses two of the urban intervention challenges – where and
how – via the application of a 21st century planning tool ENVISION
created for this purpose.
Abstract: This work examines thermal convection in two porous
layers. Flow in the upper layer is governed by Brinkman-s equations
model and in the lower layer is governed by Darcy-s model.
Legendre polynomials are used to obtain numerical solution when the
lower layer is heated from below.
Abstract: In this work a dual laser triangulation system is presented for fast building of 2.5D textured models of objects within a production line. This scanner is designed to produce data suitable for 3D completeness inspection algorithms. For this purpose two laser projectors have been used in order to considerably reduce the problem of occlusions in the camera movement direction. Results of reconstruction of electronic boards are presented, together with a comparison with a commercial system.
Abstract: The paper presents a method for multivariate time
series forecasting using Independent Component Analysis (ICA), as a preprocessing tool. The idea of this approach is to do the forecasting in the space of independent components (sources), and then to transform back the results to the original time series
space. The forecasting can be done separately and with a different
method for each component, depending on its time structure. The
paper gives also a review of the main algorithms for independent component analysis in the case of instantaneous mixture models, using second and high-order statistics. The method has been applied in simulation to an artificial multivariate time series
with five components, generated from three sources and a mixing matrix, randomly generated.