Abstract: This article discusses stress analysis and the shape characteristics of the inflatable wing, and then introduces the design method of inflatable wing, in order to accurately approximate a standard airfoil. It specifically analyses the aerodynamic characteristics of the inflatable wing with the method of CFD, along with comparing to standard airfoil, afterwards we carries out the manufacture of inflatable wing and the flight test.
Abstract: Wind turbines with double output induction
generators can operate at variable speed permitting conversion
efficiency maximization over a wide range of wind velocities. This
paper presents the performance analysis of a wind driven double
output induction generator (DOIG) operating at varying shafts speed.
A periodic transient state analysis of DOIG equipped with two
converters is carried out using a hybrid induction machine model.
This paper simulates the harmonic content of waveforms in various
points of drive at different speeds, based on the hybrid model
(dqabc). Then the sinusoidal and trapezoidal pulse-width–modulation
control techniques are used in order to improve the power factor of
the machine and to weaken the injected low order harmonics to the
supply. Based on the frequency spectrum, total harmonics distortion,
distortion factor and power factor. Finally advantages of sinusoidal
and trapezoidal pulse width modulation techniques are compared.
Abstract: This study aims to clarify constructions which enable to improve socio-cultural values of environments and also to obtain new knowledge on selecting development plans. CVM is adopted as a method of evaluation. As a case of the research, university campus (CP; the following) is selected on account of its various environments, institutions and many users. Investigations were conducted from 4 points of view, total value and utility value of whole CP environments, values of each environment existing in CP or development plan assumed in CP. Furthermore, respondents- attributes were also investigated. In consequence, the following is obtained. 1) Almost all of total value of CP is composed of utility value of direct use. 2) Each of environment and development plans whose value is the highest is clarified. 3) Moreover, development plan to improve environmental value the most is specified.
Abstract: Automobile Industry has great importance in the
Spanish economy (8,7 % of the active Spanish population is
employed in this sector).The above mentioned sector has been one of
the principal sectors affected by the current economic crisis,
consistently, the budgets in advertising have been severely limited
(46,9 % less in the period of reference), these needs of reduction
have originated a substantial change in the advertising strategy (from
2007 the increase of the advertising investment in Internet is 251,6
%), and increase profitability. The growing use of social media by
consumers therefore makes online consumer conversations an
attractive additional format for Automobile firms to promote
products at a lower cost. This research analyzes the relation between
the activity in Social Media and the design in the car industry,
looking for relations between strategies of design based on Social
Media and sales and a channel of information for companies to know
what the consumer preferences. For this ongoing research we used a
longitudinal withdrawal of information has been used using
information of panel. Managerial and research implications of the
finding are discussed.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.
Abstract: This work presents a fusion of Log Gabor Wavelet
(LGW) and Maximum a Posteriori (MAP) estimator as a speech
enhancement tool for acoustical background noise reduction. The
probability density function (pdf) of the speech spectral amplitude is
approximated by a Generalized Laplacian Distribution (GLD).
Compared to earlier estimators the proposed method estimates the
underlying statistical model more accurately by appropriately
choosing the model parameters of GLD. Experimental results show
that the proposed estimator yields a higher improvement in
Segmental Signal-to-Noise Ratio (S-SNR) and lower Log-Spectral
Distortion (LSD) in two different noisy environments compared to
other estimators.
Abstract: With the proliferation of multi-channel retailing, developing a better understanding of the factors that affect customers- purchase behaviors within a multi-channel retail context has become an important topic for practitioners and academics. While many studies have investigated the various customer behaviors associated with brick-and-mortar retailing, online retailing, and brick-and-click retailing, little research has explored how customer shopping value perceptions influence online purchase behaviors within the TV-and-online retail environment. The main purpose of this study is to investigate the influence of TV and online shopping values on online patronage intention. Data collected from 116 respondents in Taiwan are tested against the research model using the partial least squares (PLS) approach. The results indicate that utilitarian and hedonic TV shopping values have indirect, positive influences on online patronage intention through their online counterparts in the TV-and-online retail context. The findings of this study provide several important theoretical and practical implications for multi-channel retailing.
Abstract: The shortest path (SP) problem concerns with finding the shortest path from a specific origin to a specified destination in a given network while minimizing the total cost associated with the path. This problem has widespread applications. Important applications of the SP problem include vehicle routing in transportation systems particularly in the field of in-vehicle Route Guidance System (RGS) and traffic assignment problem (in transportation planning). Well known applications of evolutionary methods like Genetic Algorithms (GA), Ant Colony Optimization, Particle Swarm Optimization (PSO) have come up to solve complex optimization problems to overcome the shortcomings of existing shortest path analysis methods. It has been reported by various researchers that PSO performs better than other evolutionary optimization algorithms in terms of success rate and solution quality. Further Geographic Information Systems (GIS) have emerged as key information systems for geospatial data analysis and visualization. This research paper is focused towards the application of PSO for solving the shortest path problem between multiple points of interest (POI) based on spatial data of Allahabad City and traffic speed data collected using GPS. Geovisualization of results of analysis is carried out in GIS.
Abstract: Testing accounts for the major percentage of technical
contribution in the software development process. Typically, it
consumes more than 50 percent of the total cost of developing a
piece of software. The selection of software tests is a very important
activity within this process to ensure the software reliability
requirements are met. Generally tests are run to achieve maximum
coverage of the software code and very little attention is given to the
achieved reliability of the software. Using an existing methodology,
this paper describes how to use Bayesian Belief Networks (BBNs) to
select unit tests based on their contribution to the reliability of the
module under consideration. In particular the work examines how the
approach can enhance test-first development by assessing the quality
of test suites resulting from this development methodology and
providing insight into additional tests that can significantly reduce
the achieved reliability. In this way the method can produce an
optimal selection of inputs and the order in which the tests are
executed to maximize the software reliability. To illustrate this
approach, a belief network is constructed for a modern software
system incorporating the expert opinion, expressed through
probabilities of the relative quality of the elements of the software,
and the potential effectiveness of the software tests. The steps
involved in constructing the Bayesian Network are explained as is a
method to allow for the test suite resulting from test-driven
development.
Abstract: Cancer becomes one of the leading cause of death in
many countries over the world. Fourier-transform infrared (FTIR)
spectra of human lung cancer cells (A549) treated with PMF (natural
product extracted from PM 701) for different time intervals were
examined. Second derivative and difference method were taken in
comparison studies. Cesium (Cs) and Rubidium (Rb) nanoparticles in
PMF were detected by Energy Dispersive X-ray attached to Scanning
Electron Microscope SEM-EDX. Characteristic changes in protein
secondary structure, lipid profile and changes in the intensities of
DNA bands were identified in treated A549 cells spectra. A
characteristic internucleosomal ladder of DNA fragmentation was
also observed after 30 min of treatment. Moreover, the pH values
were significantly increases upon treatment due to the presence of Cs
and Rb nanoparticles in the PMF fraction. These results support the
previous findings that PMF is selective anticancer agent and can
produce apoptosis to A549 cells.
Abstract: Radial flow reactor was focused for large scale
methanol synthesis and in which the heat transfer type was cross-flow.
The effects of operating conditions including the reactor inlet air
temperature, the heating pipe temperature and the air flow rate on the
cross-flow heat transfer was investigated and the results showed that
the temperature profile of the area in front of the heating pipe was
slightly affected by all the operating conditions. The main area whose
temperature profile was influenced was the area behind the heating
pipe. The heat transfer direction according to the air flow directions. In
order to provide the basis for radial flow reactor design calculation, the
dimensionless number group method was used for data fitting of the
bed effective thermal conductivity and the wall heat transfer
coefficient which was calculated by the mathematical model with the
product of Reynolds number and Prandtl number. The comparison of
experimental data and calculated value showed that the calculated
value fit the experimental data very well and the formulas could be
used for reactor designing calculation.
Abstract: lack of convenience condition is one of the problems
in open spaces in hot and dry regions. Nowadays parks and green
landscapes was designed and constructed without any attention to
convenience condition. If this process continues, Citizens will encounter
with some problems. Harsh climatic condition decreases the
efficiency of people-s activities. However there is hard environment
condition in hot and dry regions, Convenience condition has been
provided in Iranian traditional architecture by using techniques and
methods. In this research at the first step characteristics of Iranian
garden that can effect on creating sustainable spaces were
investigated through observation method. Pleasure space in cities will
be created with using these methods and techniques in future cities.
Furthermore the comparison between Iranian garden and landscape in
today-s cities demonstrate the effectiveness of Iranian garden
characteristics on sustainable spaces. Iranian architects used simple
and available methods for creating open architectural spaces. In
addition desirable conditions were provided with taking in to account
both physically and spiritually. Parks and landscapes in future cities
can be designed and constructed with respect to architectural
techniques that used in Iranian gardens in hot and arid regions.
Abstract: Multi-site damage (MSD) has been a challenge to
aircraft, civil and power plant structures. In real life components are subjected to cracking at many vulnerable locations such as the bolt
holes. However, we do not consider for the presence of multiple cracks. Unlike components with a single crack, these components are
difficult to predict. When two cracks approach one another, their
stress fields influence each other and produce enhancing or shielding effect depending on the position of the cracks. In the present study,
numerical studies on fracture analysis have been conducted by using
the developed code based on the modified virtual crack closure integral (MVCCI) technique and finite element analysis (FEA) software ABAQUS for computing SIF of plates with multiple cracks.
Various parametric studies have been carried out and the results have
been compared with literature where ever available and also with the solution, obtained by using ABAQUS. By conducting extensive
numerical studies expressions for SIF have been obtained for collinear cracks and non-aligned cracks.
Abstract: The contents of nitrates and nitrites were monitored in
15 ground water resources of a selected region earmarked for the
emergency supply of population. The resources have been selected on
the basis of previous assessment of natural conditions and the
exploitation of territory in the infiltration area as well as the
surroundings of water resources. The health risk analysis carried out
in relation to nitrates and nitrites, which were found to be the most
serious water contaminants, proved, that 14 resources met the health
standards in relation to the assessed criterion and could be included in
crisis plans. Water quality of ground resources may be assessed in the
same way with regard to other contaminants.
Abstract: This paper dissertates about issues which may occur
after next year will be major part of civil aviation in EU included into
system of Emission trading. This system should help to fight against
global warming and to fulfill Kyoto Protocol commitments of
European countries. Main issues mentioned in this paper are
connected with problem of radiative forcing from emissions and lack
of their monitoring and charging in EU legislative. There are
mentioned main differences between industrial emissions and
emissions form aviation with notification about possible negative
impacts of neglecting these differences. Special attention is dedicated
to risk of possible reverse effect of inclusion aviation in EU ETS,
which may theoretically occur.
Abstract: Currently, web usage make a huge data from a lot of
user attention. In general, proxy server is a system to support web
usage from user and can manage system by using hit rates. This
research tries to improve hit rates in proxy system by applying data
mining technique. The data set are collected from proxy servers in the
university and are investigated relationship based on several features.
The model is used to predict the future access websites. Association
rule technique is applied to get the relation among Date, Time, Main
Group web, Sub Group web, and Domain name for created model.
The results showed that this technique can predict web content for the
next day, moreover the future accesses of websites increased from
38.15% to 85.57 %.
This model can predict web page access which tends to increase
the efficient of proxy servers as a result. In additional, the
performance of internet access will be improved and help to reduce
traffic in networks.
Abstract: Contamination of aromatic compounds in water can
cause severe long-lasting effects not only for biotic organism but also
on human health. Several alternative technologies for remediation of
polluted water have been attempted. One of these is adsorption
process of aromatic compounds by using organic modified clay
mineral. Porous structure of clay is potential properties for molecular
adsorptivity and it can be increased by immobilizing hydrophobic
structure to attract organic compounds. In this work natural
montmorillonite were modified with cetyltrimethylammonium
(CTMA+) and was evaluated for use as adsorbents of aromatic
compounds: benzene, toluene, and 2-chloro phenol in its single and
multicomponent solution by ethanol:water solvent. Preparation of
CTMA-montmorillonite was conducted by simple ion exchange
procedure and characterization was conducted by using x-day
diffraction (XRD), Fourier-transform infra red (FTIR) and gas
sorption analysis. The influence of structural modification of
montmorillonite on its adsorption capacity and adsorption affinity of
organic compound were studied. It was shown that adsorptivity of
montmorillonite was increased by modification associated with
arrangements of CTMA+ in the structure even the specific surface
area of modified montmorillonite was lower than raw
montmorillonite. Adsorption rate indicated that material has affinity
to adsorb compound by following order: benzene> toluene > 2-chloro
phenol. The adsorption isotherms of benzene and toluene showed 1st
order adsorption kinetic indicating a partition phenomenon of
compounds between the aqueous and organophilic CTMAmontmorillonite.
Abstract: The pavement constructions on soft and expansive soils are not durable and unable to sustain heavy traffic loading. As a result, pavement failures and settlement problems will occur very often even under light traffic loading due to cyclic and rolling effects. Geotechnical engineers have dwelled deeply into this matter, and adopt various methods to improve the engineering characteristics of soft fine-grained soils and expansive soils. The problematic soils are either replaced by good and better quality material or treated by using chemical stabilization with various binding materials. Increased the strength and durability are also the part of the sustainability drive to reduce the environment footprint of the built environment by the efficient use of resources and waste recycle materials. This paper presents a series of laboratory tests and evaluates the effect of cement and fly ash on the strength and drainage characteristics of soil in Miri. The tests were performed at different percentages of cement and fly ash by dry weight of soil. Additional tests were also performed on soils treated with the combinations of fly ash with cement and lime. The results of this study indicate an increase in unconfined compression strength and a decrease in hydraulic conductivity of the treated soil.
Abstract: Information and Communication Technologies (ICT) are increasing in importance everyday, especially since the 90’s (last decade of birth for the Millennials generation). While social interactions involving the Millennials generation have been studied, a lack of investigation remains regarding the use of the ICT by this generation as well as the impact on outcomes in education and professional training. Observing and interviewing students preparing a MSc, we aimed at characterizing the interaction students-ICT during the courses. We found that up to 50% of the students (mainly female) could use ICT during courses at a rate of 0.84 occurrence/minutes for some of them, and they thought this involvement did not disturb learning, even was helpful. As recent researches show that multitasking leads people think they are much better than they actually are, further observations with assessments are needed to conclude whether or not the use ICT by students during the courses is a real strength.
Abstract: Cerium-doped lanthanum bromide LaBr3:Ce(5%)
crystals are considered to be one of the most advanced scintillator
materials used in PET scanning, combining a high light yield, fast
decay time and excellent energy resolution. Apart from the correct
choice of scintillator, it is also important to optimise the detector
geometry, not least in terms of source-to-detector distance in order to
obtain reliable measurements and efficiency. In this study a
commercially available 25 mm x 25 mm BrilLanCeTM 380 LaBr3: Ce
(5%) detector was characterised in terms of its efficiency at varying
source-to-detector distances. Gamma-ray spectra of 22Na, 60Co, and
137Cs were separately acquired at distances of 5, 10, 15, and 20cm. As
a result of the change in solid angle subtended by the detector, the
geometric efficiency reduced in efficiency with increasing distance.
High efficiencies at low distances can cause pulse pile-up when
subsequent photons are detected before previously detected events
have decayed. To reduce this systematic error the source-to-detector
distance should be balanced between efficiency and pulse pile-up
suppression as otherwise pile-up corrections would need to be
necessary at short distances. In addition to the experimental
measurements Monte Carlo simulations have been carried out for the
same setup, allowing a comparison of results. The advantages and
disadvantages of each approach have been highlighted.