Abstract: Ground-source heat pumps achieve higher efficiencies
than conventional air-source heat pumps because they exchange heat
with the ground that is cooler in summer and hotter in winter than the
air environment. Earth heat exchangers are essential parts of the
ground-source heat pumps and the accurate prediction of their
performance is of fundamental importance. This paper presents the
development and validation of a numerical model through an
incompressible fluid flow, for the simulation of energy and
temperature changes in and around a U-tube borehole heat
exchanger. The FlexPDE software is used to solve the resulting
simultaneous equations that model the heat exchanger. The validated
model (through a comparison with experimental data) is then used to
extract conclusions on how various parameters like the U-tube
diameter, the variation of the ground thermal conductivity and
specific heat and the borehole filling material affect the temperature
of the fluid.
Abstract: A cart-ball system is a challenging system from the
control engineering point of view. This is due to the nonlinearities,
multivariable, and non-minimum phase behavior present in this
system. This paper is concerned with the problem of modeling and
control of such system. The objective of control strategy is to place
the cart at a desired position while balancing the ball on the top of the
arc-shaped track fixed on the cart. A State-Feedback Controller
(SFC) with a pole-placement method will be designed in order to
control the system. At first, the mathematical model of a cart-ball
system in the state-space form is developed. Then, the linearization of
a model will be established in order to design a SFC. The integral
control strategy will be performed as to control the cart position of a
system. Simulation work is then performed using
MATLAB/SIMULINK software in order to study the performance of
SFC when applied to the system.
Abstract: One major difficulty that faces developers of
concurrent and distributed software is analysis for concurrency based
faults like deadlocks. Petri nets are used extensively in the
verification of correctness of concurrent programs. ECATNets [2] are
a category of algebraic Petri nets based on a sound combination of
algebraic abstract types and high-level Petri nets. ECATNets have
'sound' and 'complete' semantics because of their integration in
rewriting logic [12] and its programming language Maude [13].
Rewriting logic is considered as one of very powerful logics in terms
of description, verification and programming of concurrent systems.
We proposed in [4] a method for translating Ada-95 tasking
programs to ECATNets formalism (Ada-ECATNet). In this paper,
we show that ECATNets formalism provides a more compact
translation for Ada programs compared to the other approaches based
on simple Petri nets or Colored Petri nets (CPNs). Such translation
doesn-t reduce only the size of program, but reduces also the number
of program states. We show also, how this compact Ada-ECATNet
may be reduced again by applying reduction rules on it. This double
reduction of Ada-ECATNet permits a considerable minimization of
the memory space and run time of corresponding Maude program.
Abstract: Prediction of fault-prone modules provides one way to
support software quality engineering. Clustering is used to determine
the intrinsic grouping in a set of unlabeled data. Among various
clustering techniques available in literature K-Means clustering
approach is most widely being used. This paper introduces K-Means
based Clustering approach for software finding the fault proneness of
the Object-Oriented systems. The contribution of this paper is that it
has used Metric values of JEdit open source software for generation
of the rules for the categorization of software modules in the
categories of Faulty and non faulty modules and thereafter
empirically validation is performed. The results are measured in
terms of accuracy of prediction, probability of Detection and
Probability of False Alarms.
Abstract: Nowadays companies strive to survive in a
competitive global environment. To speed up product
development/modifications, it is suggested to adopt a collaborative
product development approach. However, despite the advantages of
new IT improvements still many CAx systems work separately and
locally. Collaborative design and manufacture requires a product
information model that supports related CAx product data models. To
solve this problem many solutions are proposed, which the most
successful one is adopting the STEP standard as a product data model
to develop a collaborative CAx platform. However, the improvement
of the STEP-s Application Protocols (APs) over the time, huge
number of STEP AP-s and cc-s, the high costs of implementation,
costly process for conversion of older CAx software files to the STEP
neutral file format; and lack of STEP knowledge, that usually slows
down the implementation of the STEP standard in collaborative data
exchange, management and integration should be considered. In this
paper the requirements for a successful collaborative CAx system is
discussed. The STEP standard capability for product data integration
and its shortcomings as well as the dominant platforms for supporting
CAx collaboration management and product data integration are
reviewed. Finally a platform named LAYMOD to fulfil the
requirements of CAx collaborative environment and integrating the
product data is proposed. The platform is a layered platform to enable
global collaboration among different CAx software
packages/developers. It also adopts the STEP modular architecture
and the XML data structures to enable collaboration between CAx
software packages as well as overcoming the STEP standard
limitations. The architecture and procedures of LAYMOD platform
to manage collaboration and avoid contradicts in product data
integration are introduced.
Abstract: Through inward perceptions, we intuitively expect
distributed software development to increase the risks associated with
achieving cost, schedule, and quality goals. To compound this
problem, agile software development (ASD) insists one of the main
ingredients of its success is cohesive communication attributed to
collocation of the development team. The following study identified
the degree of communication richness needed to achieve comparable
software quality (reduce pre-release defects) between distributed and
collocated teams. This paper explores the relevancy of
communication richness in various development phases and its
impact on quality. Through examination of a large distributed agile
development project, this investigation seeks to understand the levels
of communication required within each ASD phase to produce
comparable quality results achieved by collocated teams. Obviously,
a multitude of factors affects the outcome of software projects.
However, within distributed agile software development teams, the
mode of communication is one of the critical components required to
achieve team cohesiveness and effectiveness. As such, this study
constructs a distributed agile communication model (DAC-M) for
potential application to similar distributed agile development efforts
using the measurement of the suitable level of communication. The
results of the study show that less rich communication methods, in
the appropriate phase, might be satisfactory to achieve equivalent
quality in distributed ASD efforts.
Abstract: One of the most important aspects expected from an
ERP system is to mange user\administrator manual documents
dynamically. Since an ERP package is frequently changed during its
implementation in customer sites, it is often needed to add new
documents and/or apply required changes to existing documents in
order to cover new or changed capabilities. The worse is that since
these changes occur continuously, the corresponding documents
should be updated dynamically; otherwise, implementing the ERP
package in the organization encounters serious risks. In this paper, we
propose a new architecture which is based on the agent oriented
vision and supplies the dynamic document generation expected from
ERP systems using several independent but cooperative agents.
Beside the dynamic document generation which is the main issue of
this paper, the presented architecture will address some aspects of
intelligence and learning capabilities existing in ERP.
Abstract: Air conditioning is mainly to be used as human
comfort medium. It has been use more often in country in which the
daily temperatures are high. In scientific, air conditioning is defined
as a process of controlling the moisture, cooling, heating and cleaning
air. Without proper estimation of cooling load, big amount of waste
energy been used because of unsuitable of air conditioning system are
not considering to overcoming heat gains from surrounding. This is
due to the size of the room is too big and the air conditioning has to
use more energy to cool the room and the air conditioning is too
small for the room. The studies are basically to develop a program to
calculate cooling load. Through this study it is easy to calculate
cooling load estimation. Furthermore it-s help to compare the cooling
load estimation by hourly and yearly. Base on the last study that been
done, the developed software are not user-friendly. For individual
without proper knowledge of calculating cooling load estimation
might be problem. Easy excess and user-friendly should be the main
objective to design something. This program will allow cooling load
able be estimate by any users rather than estimation by using rule of
thumb. Several of limitation of case study is judged to sure it-s
meeting to Malaysia building specification. Finally validation is done
by comparison manual calculation and by developed program.
Abstract: Electromagnetic flow meter by measuring the varying of magnetic flux, which is related to the velocity of conductive flow, can measure the rate of fluids very carefully and precisely. Electromagnetic flow meter operation is based on famous Faraday's second Law. In these equipments, the constant magnetostatic field is produced by electromagnet (winding around the tube) outside of pipe and inducting voltage that is due to conductive liquid flow is measured by electrodes located on two end side of the pipe wall. In this research, we consider to 2-dimensional mathematical model that can be solved by numerical finite difference (FD) solution approach to calculate induction potential between electrodes. The fundamental concept to design the electromagnetic flow meter, exciting winding and simulations are come out by using MATLAB and PDE-Tool software. In the last stage, simulations results will be shown for improvement and accuracy of technical provision.
Abstract: Buoyancy driven heat transfer of nanofluids in a
cylindrical enclosure used as a control unit in the subsea hydrocarbon
injection wells is investigated in this study. The governing equations
obtained with the Boussinesq approximation are solved using Comsol
Multiphysics finite element analysis and simulation software. The
base fluid is water and CuO is used as nanoparticles. Solution is
obtained for nanoparticle solid volume fraction of 8% and for
Rayleigh number in the range of 105-107. The results show that
nanoparticle usage in the cylindrical electronic control unit has a
significant effect on the flow and heat transfer.
Abstract: Saturated hydraulic conductivity is one of the soil
hydraulic properties which is widely used in environmental studies
especially subsurface ground water. Since, its direct measurement is
time consuming and therefore costly, indirect methods such as
pedotransfer functions have been developed based on multiple linear
regression equations and neural networks model in order to estimate
saturated hydraulic conductivity from readily available soil
properties e.g. sand, silt, and clay contents, bulk density, and organic
matter. The objective of this study was to develop neural networks
(NNs) model to estimate saturated hydraulic conductivity from
available parameters such as sand and clay contents, bulk density,
van Genuchten retention model parameters (i.e. r
θ , α , and n) as well
as effective porosity. We used two methods to calculate effective
porosity: : (1) eff s FC φ =θ -θ , and (2) inf φ =θ -θ eff s , in which s
θ is
saturated water content, FC θ is water content retained at -33 kPa
matric potential, and inf θ is water content at the inflection point.
Total of 311 soil samples from the UNSODA database was divided
into three groups as 187 for the training, 62 for the validation (to
avoid over training), and 62 for the test of NNs model. A commercial
neural network toolbox of MATLAB software with a multi-layer
perceptron model and back propagation algorithm were used for the
training procedure. The statistical parameters such as correlation
coefficient (R2), and mean square error (MSE) were also used to
evaluate the developed NNs model. The best number of neurons in
the middle layer of NNs model for methods (1) and (2) were
calculated 44 and 6, respectively. The R2 and MSE values of the test
phase were determined for method (1), 0.94 and 0.0016, and for
method (2), 0.98 and 0.00065, respectively, which shows that method
(2) estimates saturated hydraulic conductivity better than method (1).
Abstract: Application of Expert System in the area of agriculture would take the form of Integrated Crop Management decision aids and would encompass water management, fertilizer management, crop protection systems and identification of implements. In order to remain competitive, the modern farmer often relies on agricultural specialists and advisors to provide information for decision-making. An expert system normally composed of a knowledge base (information, heuristics, etc.), inference engine (analyzes knowledge base), and end user interface (accepting inputs, generating outputs). Software named 'CROP-9-DSS' incorporating all modern features like, graphics, photos, video clippings etc. has been developed. This package will aid as a decision support system for identification of pest and diseases with control measures, fertilizer recommendation system, water management system and identification of farm implements for leading crops of Kerala (India) namely Coconut, Rice, Cashew, Pepper, Banana, four vegetables like Amaranthus, Bhindi, Brinjal and Cucurbits. 'CROP-9-DSS' will act as an expert system to agricultural officers, scientists in the field of agriculture and extension workers for decision-making and help them in suggesting suitable recommendations.
Abstract: A strategy is implemented to find the improved configuration design of an existing aircraft structure by executing topology and shape optimizations. Structural analysis of the Initial Design Space is performed in ANSYS under the loads pertinent to operating and ground conditions. By using the FEA results and data, an initial optimized layout configuration is attained by exploiting nonparametric topology optimization in TOSCA software. Topological optimized surfaces are then smoothened and imported in ANSYS to develop the geometrical features. Nodes at the critical locations of resulting voids are selected for sketching rough profiles. Rough profiles are further refined and CAD feasible geometric features are generated. The modified model is then analyzed under the same loadings and constraints as defined for topology optimization. Shape at the peak stress concentration areas are further optimized by exploiting the shape optimization in TOSCA.shape module. The harmonized stressed model with the modified surfaces is then imported in CATIA to develop the final design.
Abstract: Defense and Aerospace environment is continuously
striving to keep up with increasingly sophisticated Information
Technology (IT) in order to remain effective in today-s dynamic and
unpredictable threat environment. This makes IT one of the largest
and fastest growing expenses of Defense. Hundreds of millions of
dollars spent a year on IT projects. But, too many of those millions
are wasted on costly mistakes. Systems that do not work properly,
new components that are not compatible with old ones, trendy new
applications that do not really satisfy defense needs or lost through
poorly managed contracts.
This paper investigates and compiles the effective strategies that
aim to end exasperation with low returns and high cost of
Information Technology acquisition for defense; it tries to show how
to maximize value while reducing time and expenditure.
Abstract: Nowaday-s, many organizations use systems that
support business process as a whole or partially. However, in some
application domains, like software development and health care
processes, a normative Process Aware System (PAS) is not suitable,
because a flexible support is needed to respond rapidly to new
process models. On the other hand, a flexible Process Aware System
may be vulnerable to undesirable and fraudulent executions, which
imposes a tradeoff between flexibility and security. In order to make
this tradeoff available, a genetic-based anomaly detection model for
logs of Process Aware Systems is presented in this paper. The
detection of an anomalous trace is based on discovering an
appropriate process model by using genetic process mining and
detecting traces that do not fit the appropriate model as anomalous
trace; therefore, when used in PAS, this model is an automated
solution that can support coexistence of flexibility and security.
Abstract: Simulation accuracy by recent dynamic vehicle
simulation multidimensional expression significantly has progressed
and acceptable results not only for passive vehicles but also for
active vehicles normally equipped with advanced electronic
components is also provided. Recently, one of the subjects that has it
been considered, is increasing the safety car in design. Therefore,
many efforts have been done to increase vehicle stability especially
in the turn. One of the most important efforts is adjusting the camber
angle in the car suspension system. Optimum control camber angle in
addition to the vehicle stability is effective in the wheel adhesion on
road, reducing rubber abrasion and acceleration and braking. Since
the increase or decrease in the camber angle impacts on the stability
of vehicles, in this paper, a car suspension system mechanism is
introduced that could be adjust camber angle and the mechanism is
application and also inexpensive. In order to reach this purpose, in
this paper, a passive double wishbone suspension system with
variable camber angle is introduced and then variable camber
mechanism designed and analyzed for study the designed system
performance, this mechanism is modeled in Visual Nastran software
and kinematic analysis is revealed.
Abstract: This paper presents a design of source encoding
calculator software which applies the two famous algorithms in the
field of information theory- the Shannon-Fano and the Huffman
schemes. This design helps to easily realize the algorithms without
going into a cumbersome, tedious and prone to error manual
mechanism of encoding the signals during the transmission. The
work describes the design of the software, how it works, comparison
with related works, its efficiency, its usefulness in the field of
information technology studies and the future prospects of the
software to engineers, students, technicians and alike. The designed
“Encodia" software has been developed, tested and found to meet the
intended requirements. It is expected that this application will help
students and teaching staff in their daily doing of information theory
related tasks. The process is ongoing to modify this tool so that it can
also be more intensely useful in research activities on source coding.
Abstract: In this paper, the potential security issues brought by the virtualization of a Software Defined Networks (SDN) would be analyzed. The virtualization of SDN is achieved by FlowVisor (FV). With FV, a physical network is divided into multiple isolated logical networks while the underlying resources are still shared by different slices (isolated logical networks). However, along with the benefits brought by network virtualization, it also presents some issues regarding security. By examining security issues existing in an OpenFlow network, which uses FlowVisor to slice it into multiple virtual networks, we hope we can get some significant results and also can get furtherdiscussions among the security of SDN virtualization.
Abstract: This article gives a short preview of the new software
created especially for palletizing process in automated production
systems. Each chapter of this article is about problem solving in
development of modules in Java programming language. First part
describes structure of the software, its modules and data flow
between them. Second part describes all deployment methods, which
are implemented in the software. Next chapter is about twodimensional
editor created for manipulation with objects in each
layer of the load and gives calculations for collision control. Module
of virtual reality used for three-dimensional preview and creation of
the load is described in the fifth chapter. The last part of this article
describes communication and data flow between control system of
the robot, vision system and software.
Abstract: Paced Auditory Serial Addition Test (PASAT) has
been used as a common research tool for different neurological
disorders like Multiple Sclerosis. Recently, technology let
researchers to introduce a new versions of the visual test, the paced
visual serial addition test (PVSAT). In this paper, the computerized
version of these two tests is introduced. Beside the number of true
responses are interpreted, the reaction time of subjects are calculated
by the software. We hypothesize that paying attention to the reaction
time may be valuable. For this purpose, sixty eight female normal
subjects and fifty eight male normal subjects are enrolled in the
study. We investigate the similarity between the PASAT3 and
PVSAT3 in number of true responses and the new criterion (the
average reaction time of each subject). The similarity between two
tests were rejected (p-value = 0.000) which means that these two test
differ. The effect of sex in the tests were not approved since the pvalues
of different between PASAT3 and PVSAT3 in both sex is the
same (p-value = 0.000) which means that male and female subjects
performed the tests at no different level of performance. The new
criterion shows a negative correlation with the age which offers aged
normal subjects may have the same number of true responses as the
young subjects but they have latent responses. This will give prove
for the importance of reaction time.