Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: Networked schools have become a feature of
education systems in countries that seek to provide learning
opportunities in schools located beyond major centres of population.
The internet and e-learning have facilitated the development of
virtual educational structures that complement traditional schools,
encouraging collaborative teaching and learning to proceed. In rural
New Zealand and in the Atlantic Canadian province of
Newfoundland and Labrador, e-learning is able to provide new ways
of organizing teaching, learning and the management of educational
opportunities. However, the future of e-teaching and e-learning in
networked schools depends on the development of professional
education programs that prepare teachers for collaborative teaching
and learning environments in which both virtual and traditional face
to face instruction co-exist.
Abstract: this paper presented a survey analysis subjected on
network bandwidth management from published papers referred in
IEEE Explorer database in three years from 2009 to 2011. Network
Bandwidth Management is discussed in today-s issues for computer
engineering applications and systems. Detailed comparison is
presented between published papers to look further in the IP based
network critical research area for network bandwidth management.
Important information such as the network focus area, a few
modeling in the IP Based Network and filtering or scheduling used in
the network applications layer is presented. Many researches on
bandwidth management have been done in the broad network area
but fewer are done in IP Based network specifically at the
applications network layer. A few researches has contributed new
scheme or enhanced modeling but still the issue of bandwidth
management still arise at the applications network layer. This survey
is taken as a basic research towards implementations of network
bandwidth management technique, new framework model and
scheduling scheme or algorithm in an IP Based network which will
focus in a control bandwidth mechanism in prioritizing the network
traffic the applications layer.
Abstract: To establish optical communication between any two
satellites, the transmitter satellite must track the beacon of the
receiver satellite and point the information optical beam in its
direction. Optical tracking and pointing systems for free space suffer
during tracking from high-amplitude vibration because of
background radiation from interstellar objects such as the Sun, Moon,
Earth, and stars in the tracking field of view or the mechanical
impact from satellite internal and external sources. The vibrations of
beam pointing increase the bit error rate and jam communication
between the two satellites. One way to overcome this problem is the
use of very small transmitter beam divergence angles of too narrow
divergence angle is that the transmitter beam may sometimes miss
the receiver satellite, due to pointing vibrations. In this paper we
propose the use of genetic algorithm to optimize the BER as function
of transmitter optics aperture.
Abstract: Nowadays use of a new structural bracing system
called 'Knee Bracing System' have taken the specialists attention too
much. On the other hand nonlinear static analysis procedures in
estimate structures performance in earthquake time have taken
attention too much. One of these procedure is modal pushover
analysis (MPA) procedure. The accuracy of MPA procedure for
simple steel moment resisting frame has been verified and considered
in Chintanapakdee and Chopra-s article in 2003. Since the accuracy
of MPA procedure has not verified for semi-rigid steel frames with
knee bracing, we are going to get through with this matter in this
study. For this purpose, the selected structures are four frames with
different heights, 5 to 20 stories, will be designed according to AISC
criteria. Then MPA procedure is used for the same frames with
different rigidity percentiles of connections. The results of seismic
responses are compared with dynamic nonlinear response history
analysis as exact procedure and accuracy of MPA procedure is
evaluated. It seems that MPA procedure accuracy will come down by
reduction of the rigidity percentiles of semi-rigid connections.
Abstract: Let p be a prime number, Fpbe a finite field and let Qpdenote the set of quadratic residues in Fp. In the first section we givesome notations and preliminaries from elliptic curves. In the secondsection, we consider some properties of rational points on ellipticcurves Ep,b: y2= x3+ b2 over Fp, where b ∈ F*p. Recall that theorder of Ep,bover Fpis p + 1 if p ≡ 5(mod 6). We generalize thisresult to any field Fnp for an integer n≥ 2. Further we obtain someresults concerning the sum Σ[x]Ep,b(Fp) and Σ[y]Ep,b(Fp), thesum of x- and y- coordinates of all points (x, y) on Ep,b, and alsothe the sum Σ(x,0)Ep,b(Fp), the sum of points (x, 0) on Ep,b.
Abstract: This report shows the performance of composite
biodegradable film from chitosan, starch and sawdust fiber. The main
objectives of this research are to fabricate and characterize composite
biodegradable film in terms of morphology and physical properties.
The film was prepared by casting method. Sawdust fiber was used as
reinforcing agent and starch as polymer matrix in the casting
solution. The morphology of the film was characterized using atomic
force microscope (AFM). The result showed that the film has
smooth structure. Chemical composition of the film was investigated
using Fourier transform infrared (FTIR) where the result revealed
present of starch in the film. The thermal properties were
characterized using thermal gravimetric analyzer (TGA) and
differential scanning calorimetric (DSC) where the results showed
that the film has small difference in melting and degradation
temperature.
Abstract: In the meantime, there were lots of hardware solutions like products or urban facilities for crime prevention in the public design area. Meanwhile, people have growing interest in public design so by making a village; community design in public design is getting active by the society. The system for crime prevention is actively done by the citizens who created the community. Regarding the social situation, in this project, we saw it as a kind of community design practices and researched about 'how does community design influence Crime prevention?' The purpose of this study is to propose the community design as a way of preventing the crime in the city. First, we found out about the definition, elements and methods of community design by reviewing the theory. And then, this study analyzed the case that was enforced in Seoul and organize the elements and methods of community design. This study can be refer to Public Design based on civil participation and make the community design area contribute to expand the way of solving social problems.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: Data mining (DM) is the process of finding and extracting frequent patterns that can describe the data, or predict unknown or future values. These goals are achieved by using various learning algorithms. Each algorithm may produce a mining result completely different from the others. Some algorithms may find millions of patterns. It is thus the difficult job for data analysts to select appropriate models and interpret the discovered knowledge. In this paper, we describe a framework of an intelligent and complete data mining system called SUT-Miner. Our system is comprised of a full complement of major DM algorithms, pre-DM and post-DM functionalities. It is the post-DM packages that ease the DM deployment for business intelligence applications.
Abstract: This paper presents a new approach for setting
frequency relays based on the dynamic of power system. A
simplified model of the power system based on the load-frequency
control loop will be developed to be used instead of the complete
model of the power system. The effects of the equipments and their
responses on the frequency variations of the power plant will be
investigated and then a method for adaptive settings of frequency
relays will be explained. The proposed method will be investigated
by analyzing a simplified model of a power plant by MATLAB
software.
Abstract: There are four challenges of sustainable development
and in corporate level sustainability management-s role is to answer
for ecological sustainability challenge, social sustainability challenge,
economic sustainability challenges to environment and social
management and integration challenge of corporate sustainable
challenges by the help of different concepts, methods, instruments,
which are in the toolbox of sustainability management. These
instruments, concepts have different relevance in these challenges,
and according to different literatures environmental management is
outside of social and integration challenge. Main aim of this paper is
to represent the answer for the question that: is it true that social and
integration point of view is outside of the concept environmental
accounting? Using literature review and primer research at the end of
the paper the answer will be confirmed.
Abstract: Nowadays, several techniques such as; Fuzzy
Inference System (FIS) and Neural Network (NN) are employed for
developing of the predictive models to estimate parameters of water
quality. The main objective of this study is to compare between the
predictive ability of the Adaptive Neuro-Fuzzy Inference System
(ANFIS) model and Artificial Neural Network (ANN) model to
estimate the Biochemical Oxygen Demand (BOD) on data from 11
sampling sites of Saen Saep canal in Bangkok, Thailand. The data is
obtained from the Department of Drainage and Sewerage, Bangkok
Metropolitan Administration, during 2004-2011. The five parameters
of water quality namely Dissolved Oxygen (DO), Chemical Oxygen
Demand (COD), Ammonia Nitrogen (NH3N), Nitrate Nitrogen
(NO3N), and Total Coliform bacteria (T-coliform) are used as the
input of the models. These water quality indices affect the
biochemical oxygen demand. The experimental results indicate that
the ANN model provides a higher correlation coefficient (R=0.73)
and a lower root mean square error (RMSE=4.53) than the
corresponding ANFIS model.
Abstract: The development of renewable energies - particularly energy from wind, water, solar power and biomass - is a central aim of the European Commission's energy policy. There are several reasons for this choice: renewable energies are sustainable, nonpolluting, widely available and clean. Increasing the share of renewable energy in the energy balance enhances sustainability. It also helps to improve the security of energy supply by reducing the Community's growing dependence on imported energy sources.In this paper it was studied the possibility to realize three photovoltaic systems in the Italian Natural Park “Gola della Rossa e di Frasassi". The first photovoltaic system is a grid-connected system for Services and Documentation Center of Castelletta with a nominal power of about 6 kWp. The second photovoltaic system is a grid-connected integrated system on the ticket office-s roof with a nominal power of about 4 kWp. The third project is set up by five grid-connected systems integrated on the roofs of the bungalows in Natural Park-s tourist camping with a nominal power of about 10 kWp. The electricity which is generated by all these plants is purchased according to the Italian program called “Conto Energia". Economical analysis and the amount of the avoided CO2 emissions are elaborated for these photovoltaic systems.
Abstract: Laser Profiler (LP) data from aerial laser surveys have
been increasingly used as topographical inputs to numerical
simulations of flooding and inundation in river basins. LP data has
great potential for reproducing topography, but its effective usage has
not yet been fully established. In this study, flooding and inundation
are simulated numerically using LP data for the Jobaru River basin of
Japan’s Saga Plain. The analysis shows that the topography is
reproduced satisfactorily in the computational domain with urban and
agricultural areas requiring different grid sizes. A 2-D numerical
simulation shows that flood flow behavior changes as grid size is
varied.
Abstract: Understanding proteins functions is a major goal in
the post-genomic era. Proteins usually work in context of other
proteins and rarely function alone. Therefore, it is highly relevant to
study the interaction partners of a protein in order to understand its
function. Machine learning techniques have been widely applied to
predict protein-protein interactions. Kernel functions play an
important role for a successful machine learning technique. Choosing
the appropriate kernel function can lead to a better accuracy in a
binary classifier such as the support vector machines. In this paper,
we describe a Bayesian kernel for the support vector machine to
predict protein-protein interactions. The use of Bayesian kernel can
improve the classifier performance by incorporating the probability
characteristic of the available experimental protein-protein
interactions data that were compiled from different sources. In
addition, the probabilistic output from the Bayesian kernel can assist
biologists to conduct more research on the highly predicted
interactions. The results show that the accuracy of the classifier has
been improved using the Bayesian kernel compared to the standard
SVM kernels. These results imply that protein-protein interaction can
be predicted using Bayesian kernel with better accuracy compared to
the standard SVM kernels.
Abstract: This paper presents methodologies for developing an
intelligent CAD system assisting in analysis and design of
reconfigurable special machines. It describes a procedure for
determining feasibility of utilizing these machines for a given part
and presents a model for developing an intelligent CAD system. The
system analyzes geometrical and topological information of the given
part to determine possibility of the part being produced by
reconfigurable special machines from a technical point of view. Also
feasibility of the process from a economical point of view is
analyzed. Then the system determines proper positioning of the part
considering details of machining features and operations needed.
This involves determination of operation types, cutting tools and the
number of working stations needed. Upon completion of this stage
the overall layout of the machine and machining equipment required
are determined.
Abstract: This research aims to study employment trends in
printing industry for prepress support by Suan Sunandha University
Fund. The objectives of this research are to explain the trends of the
employment in Thai Printing Industry for prepress in Bangkok and
the description of different personnel that prepress entrepreneur need
and also the problems of employment.
The population of prepress entrepreneurs is about 100
organizations in the area of Bangkok. The questionnaires has been
taken and analyzed with SPSS program by using the average
percentage and standard deviation.
This research is multiple case studies. The conceptual framework
is developed on the basis of the open systems theory.
The research result show that
1. The most of prepress entrepreneur have trend to choose the
employee by any sex, the age 25-29 years old, bachelor degree
and have 1-2 years experience.
2. The most problems are the understanding in job,
communication/relation and the understanding in new
technology.
3. The trends aims to employment in 1-3 years have 57.8% for
prepress industry in Bangkok.
This research suggests that:
1. Thai printing industry for prepress in Bangkok need quality
employee that expert in printing technology.
2. Prepress entrepreneur should have agreement to development
with university for practice the employee.
3. Prepress entrepreneur should support personal to fulfill the
knowledge.
Abstract: For high-speed control of robots, a good knowledge of system modelling is necessary to obtain the desired bandwidth. In this paper, we present a cartesian robot with a pan/tilt unit in end-effector (5 dof). This robot is implemented with powerful direct drive AC induction machines. The dynamic model, parameter identification and model validation of the robot are studied (including actuators). This work considers the cartesian robot coupled and non linear (contrary to normal considerations for this type of robots). The mechanical and control architecture proposed in this paper is efficient for industrial and research application in which high speed, well known model and very high accuracy are required.