Abstract: Optical flow is a research topic of interest for many
years. It has, until recently, been largely inapplicable to real-time
applications due to its computationally expensive nature. This paper
presents a new reliable flow technique which is combined with a
motion detection algorithm, from stationary camera image streams,
to allow flow-based analyses of moving entities, such as rigidity, in
real-time. The combination of the optical flow analysis with motion
detection technique greatly reduces the expensive computation of
flow vectors as compared with standard approaches, rendering the
method to be applicable in real-time implementation. This paper
describes also the hardware implementation of a proposed pipelined
system to estimate the flow vectors from image sequences in real
time. This design can process 768 x 576 images at a very high frame
rate that reaches to 156 fps in a single low cost FPGA chip, which is
adequate for most real-time vision applications.
Abstract: Previous research has demonstrated that negative
attitudes towards people with physical disabilities and obesity are
predicted by a component of perceived vulnerability to disease; germ
aversion. These findings have been suggested as illustrations of an
evolved but over-active mechanism which promotes the avoidance of
pathogen-carrying individuals. To date, this interpretation of attitude
formation has not been explored with regard to people with
intellectual disability, and no attempts have been made to examine
possible mediating factors. This study examined attitudes in 333
adults and demonstrated that the moderate positive relationship
between germ aversion and negative attitudes toward people with
intellectual disability is fully mediated by social dominance
orientation, a general preference for hierarchies and inequalities
among social groups. These findings have implications for the
design of programs which attempt to promote community acceptance
and inclusion of people with disabilities.
Abstract: Bond graph models of an electrical transformer including
the nonlinear saturation are presented. The transformer
using electrical and magnetic circuits are modelled. These models
determine the relation between self and mutual inductances, and
the leakage and magnetizing inductances of power transformers
with two windings using the properties of a bond graph. The
equivalence between electrical and magnetic variables is given.
The modelling and analysis using this methodology to three phase
power transformers can be extended.
Abstract: To achieve accurate and precise results of finite
element analysis (FEA) of bones, it is important to represent the
load/boundary conditions as identical as possible to the human body
such as the bone properties, the type and force of the muscles, the
contact force of the joints, and the location of the muscle attachment.
In this study, the difference in the Von-Mises stress and the total
deformation was compared by classifying them into Case 1, which
shows the actual anatomical form of the muscle attached to the femur
when the same muscle force was applied, and Case 2, which gives a
simplified representation of the attached location. An inverse
dynamical musculoskeletal model was simulated using data from an
actual walking experiment to complement the accuracy of the
muscular force, the input value of FEA. The FEA method using the
results of the muscular force that were calculated through the
simulation showed that the maximum Von-Mises stress and the
maximum total deformation in Case 2 were underestimated by 8.42%
and 6.29%, respectively, compared to Case 1. The torsion energy and
bending moment at each location of the femur occurred via the stress
ingredient. Due to the geometrical/morphological feature of the femur
of having a long bone shape when the stress distribution is wide, as
shown in Case 1, a greater Von-Mises stress and total deformation are
expected from the sum of the stress ingredients. More accurate results
can be achieved only when the muscular strength and the attachment
location in the FEA of the bones and the attachment form are the same
as those in the actual anatomical condition under the various moving
conditions of the human body.
Abstract: Planar systems of electrodes arranged on both sides of dielectric piezoelectric layer are applied in numerous transducers. They are capable of electronic beam-steering of generated wave both in azimuth and elevation. The wave-beam control is achieved by addressable driving of two-dimensional transducer through proper voltage supply of electrodes on opposite surfaces of the layer. In this paper a semi-analytical method of analysis of the considered transducer is proposed, which is a generalization of the well-known BIS-expansion method. It was earlier exploited with great success in the theory of interdigital transducers of surface acoustic waves, theory of elastic wave scattering by cracks and certain advanced electrostatic problems. The corresponding nontrivial electrostatic problem is formulated and solved numerically.
Abstract: This paper describes a segmentation algorithm based
on the cooperation of an optical flow estimation method with edge
detection and region growing procedures.
The proposed method has been developed as a pre-processing
stage to be used in methodologies and tools for video/image indexing
and retrieval by content. The addressed problem consists in
extracting whole objects from background for producing images of
single complete objects from videos or photos. The extracted images
are used for calculating the object visual features necessary for both
indexing and retrieval processes.
The first task of the algorithm exploits the cues from motion
analysis for moving area detection. Objects and background are then
refined using respectively edge detection and region growing
procedures. These tasks are iteratively performed until objects and
background are completely resolved.
The developed method has been applied to a variety of indoor and
outdoor scenes where objects of different type and shape are
represented on variously textured background.
Abstract: Ferroresonance is an electrical phenomenon in
nonlinear character, which frequently occurs in power system due to
transmission line faults and single or more-phase switching on the
lines as well as usage of the saturable transformers. In this study, the
ferroresonance phenomena are investigated under the modeling of the
West Anatolian Electric Power Network of 380 kV in Turkey. The
ferroresonance event is observed as a result of removing the loads at
the end of the lines. In this sense, two different cases are considered.
At first, the switching is applied at 2nd second and the ferroresonance
affects are observed between 2nd and 4th seconds in the voltage
variations of the phase-R. Hence the ferroresonance and nonferroresonance
parts of the overall data are compared with each
others using the Fourier transform techniques to show the
ferroresonance affects.
Abstract: Most of the losses in a power system relate to
the distribution sector which always has been considered.
From the important factors which contribute to increase losses
in the distribution system is the existence of radioactive flows.
The most common way to compensate the radioactive power
in the system is the power to use parallel capacitors. In
addition to reducing the losses, the advantages of capacitor
placement are the reduction of the losses in the release peak of
network capacity and improving the voltage profile. The point
which should be considered in capacitor placement is the
optimal placement and specification of the amount of the
capacitor in order to maximize the advantages of capacitor
placement.
In this paper, a new technique has been offered for the
placement and the specification of the amount of the constant
capacitors in the radius distribution network on the basis of
Genetic Algorithm (GA). The existing optimal methods for
capacitor placement are mostly including those which reduce
the losses and voltage profile simultaneously. But the
retaliation cost and load changes have not been considered as
influential UN the target function .In this article, a holistic
approach has been considered for the optimal response to this
problem which includes all the parameters in the distribution
network: The price of the phase voltage and load changes. So,
a vast inquiry is required for all the possible responses. So, in
this article, we use Genetic Algorithm (GA) as the most
powerful method for optimal inquiry.
Abstract: A study of the obtainable watermark data rate for information hiding algorithms is presented in this paper. As the perceptual entropy for wideband monophonic audio signals is in the range of four to five bits per sample, a significant amount of additional information can be inserted into signal without causing any perceptual distortion. Experimental results showed that transform domain watermark embedding outperforms considerably watermark embedding in time domain and that signal decompositions with a high gain of transform coding, like the wavelet transform, are the most suitable for high data rate information hiding. Keywords?Digital watermarking, information hiding, audio watermarking, watermark data rate.
Abstract: In this paper we propose a new traffic simulation
package, TDMSim, which supports both macroscopic and
microscopic simulation on free-flowing and regulated traffic systems.
Both simulators are based on travel demands, which specify the
numbers of vehicles departing from origins to arrive at different
destinations. The microscopic simulator implements the carfollowing
model given the pre-defined routes of the vehicles but also
supports the rerouting of vehicles. We also propose a macroscopic
simulator which is built in integration with the microscopic simulator
to allow the simulation to be scaled for larger networks without
sacrificing the precision achievable through the microscopic
simulator. The macroscopic simulator also enables the reuse of
previous simulation results when simulating traffic on the same
networks at later time. Validations have been conducted to show the
correctness of both simulators.
Abstract: The aim of this study was to compare the
sensitometric properties of commonly used radiographic films
processed with chemical solutions in different workload hospitals.
The effect of different processing conditions on induced densities on
radiologic films was investigated. Two accessible double emulsions
Fuji and Kodak films were exposed with 11-step wedge and
processed with Champion and CPAC processing solutions. The
mentioned films provided in both workloads centers, high and low.
Our findings displays that the speed and contrast of Kodak filmscreen
in both work load (high and low) is higher than Fuji filmscreen
for both processing solutions. However there was significant
differences in films contrast for both workloads when CPAC solution
had been used (p=0.000 and 0.028). The results showed base plus
fog density for Kodak film was lower than Fuji. Generally Champion
processing solution caused more speed and contrast for investigated
films in different conditions and there was significant differences in
95% confidence level between two used processing solutions
(p=0.01). Low base plus fog density for Kodak films provide more
visibility and accuracy and higher contrast results in using lower
exposure factors to obtain better quality in resulting radiographs. In
this study we found an economic advantages since Champion
solution and Kodak film are used while it makes lower patient dose.
Thus, in a radiologic facility any change in film processor/processing
cycle or chemistry should be carefully investigated before
radiological procedures of patients are acquired.
Abstract: In this paper, the direct AnsAz method is used for constructing the multi-wave solutions to the (2+1)-dimensional extension of the Korteweg de-Vries (shortly EKdV) equation. A new breather type of three-wave solutions including periodic breather type soliton solution, breather type of two-solitary solution are obtained. Some cases with specific values of the involved parameters are plotted for each of the three-wave solutions. Mechanical features of resonance interaction among the multi-wave are discussed. These results enrich the variety of the dynamics of higher-dimensional nonlinear wave field.
Abstract: In this paper, the optimum weight and cost of a laminated composite plate is seeked, while it undergoes the heaviest load prior to a complete failure. Various failure criteria are defined for such structures in the literature. In this work, the Tsai-Hill theory is used as the failure criterion. The theory of analysis was based on the Classical Lamination Theory (CLT). A newly type of Genetic Algorithm (GA) as an optimization technique with a direct use of real variables was employed. Yet, since the optimization via GAs is a long process, and the major time is consumed through the analysis, Radial Basis Function Neural Networks (RBFNN) was employed in predicting the output from the analysis. Thus, the process of optimization will be carried out through a hybrid neuro-GA environment, and the procedure will be carried out until a predicted optimum solution is achieved.
Abstract: The background estimation approach using a small
window median filter is presented on the bases of analyzing IR point
target, noise and clutter model. After simplifying the two-dimensional
filter, a simple method of adopting one-dimensional median filter is
illustrated to make estimations of background according to the
characteristics of IR scanning system. The adaptive threshold is used
to segment canceled image in the background. Experimental results
show that the algorithm achieved good performance and satisfy the
requirement of big size image-s real-time processing.
Abstract: In a competitive production environment, critical
decision making are based on data resulted by random sampling of
product units. Efficiency of these decisions depends on data quality
and also their reliability scale. This point leads to the necessity of a
reliable measurement system. Therefore, the conjecture process and
analysing the errors contributes to a measurement system known as
Measurement System Analysis (MSA). The aim of this research is on
determining the necessity and assurance of extensive development in
analysing measurement systems, particularly with the use of
Repeatability and Reproducibility Gages (GR&R) to improve
physical measurements. Nowadays in productive industries,
repeatability and reproducibility gages released so well but they are
not applicable as well as other measurement system analysis
methods. To get familiar with this method and gain a feedback in
improving measurement systems, this survey would be on
“ANOVA" method as the most widespread way of calculating
Repeatability and Reproducibility (R&R).
Abstract: Many methods exist for either measuring or estimating
evaporation from free water surfaces. Evaporation pans provide one
of the simplest, inexpensive, and most widely used methods of
estimating evaporative losses. In this study, the rate of evaporation
starting from a water surface was calculated by modeling with
application to dams in wet, arid and semi arid areas in Algeria.
We calculate the evaporation rate from the pan using the energy
budget equation, which offers the advantage of an ease of use, but
our results do not agree completely with the measurements taken by
the National Agency of areas carried out using dams located in areas
of different climates. For that, we develop a mathematical model to
simulate evaporation. This simulation uses an energy budget on the
level of a vat of measurement and a Computational Fluid Dynamics
(Fluent). Our calculation of evaporation rate is compared then by the
two methods and with the measures of areas in situ.
Abstract: The acidity of different raw Jordanian clays
containing zeolite, bentonite, red and white kaolinite and diatomite
was characterized by means of temperature programmed desorption
(TPD) of ammonia, conversion of 2-methyl-3-butyn-2-ol (MBOH),
FTIR and BET-measurements. FTIR spectra proved presence of
silanol and bridged hydroxyls on the clay surface. The number of
acidic sites was calculated from experimental TPD-profiles. We
observed the decrease of surface acidity correlates with the decrease
of Si/Al ratio except for diatomite. On the TPD-plot for zeolite two
maxima were registered due to different strength of surface acidic
sites. Values of MBOH conversion, product yields and selectivity
were calculated for the catalysis on Jordanian clays. We obtained that
all clay samples are able to convert MBOH into a major product
which is 3-methyl-3-buten-1-yne (MBYNE) catalyzed by acid
surface sites with the selectivity close to 70%. There was found a
correlation between MBOH conversion and acidity of clays
determined by TPD-NH3, i.e. the higher the acidity the higher the
conversion of MBOH. However, diatomite provided the lowest
conversion of MBOH as result of poor polarization of silanol groups.
Comparison of surface areas and conversions revealed the highest
density of active sites for red kaolinite and the lowest for zeolite and
diatomite.
Abstract: The problem of frequent pattern discovery is defined
as the process of searching for patterns such as sets of features or items that appear in data frequently. Finding such frequent patterns
has become an important data mining task because it reveals associations, correlations, and many other interesting relationships
hidden in a database. Most of the proposed frequent pattern mining
algorithms have been implemented with imperative programming
languages. Such paradigm is inefficient when set of patterns is large
and the frequent pattern is long. We suggest a high-level declarative
style of programming apply to the problem of frequent pattern
discovery. We consider two languages: Haskell and Prolog. Our
intuitive idea is that the problem of finding frequent patterns should
be efficiently and concisely implemented via a declarative paradigm
since pattern matching is a fundamental feature supported by most
functional languages and Prolog. Our frequent pattern mining
implementation using the Haskell and Prolog languages confirms our
hypothesis about conciseness of the program. The comparative
performance studies on line-of-code, speed and memory usage of
declarative versus imperative programming have been reported in the
paper.
Abstract: Independent spanning trees (ISTs) provide a number of advantages in data broadcasting. One can cite the use in fault tolerance network protocols for distributed computing and bandwidth. However, the problem of constructing multiple ISTs is considered hard for arbitrary graphs. In this paper we present an efficient algorithm to construct ISTs on hypercubes that requires minimum resources to be performed.
Abstract: Chaiyaphum Starch Co. Ltd. is one of many starch
manufacturers that has introduced machinery to aid in manufacturing.
Even though machinery has replaced many elements and is now a
significant part in manufacturing processes, problems that must be
solved with respect to current process flow to increase efficiency still
exist. The paper-s aim is to increase productivity while maintaining
desired quality of starch, by redesigning the flipping machine-s
mechanical control system which has grossly low functional lifetime.
Such problems stem from the mechanical control system-s bearings,
as fluids and humidity can access into said bearing directly, in
tandem with vibrations from the machine-s function itself. The wheel
which is used to sense starch thickness occasionally falls from its
shaft, due to high speed rotation during operation, while the shaft
may bend from impact when processing dried bread. Redesigning its
mechanical control system has increased its efficiency, allowing
quality thickness measurement while increasing functional lifetime
an additional 62 days.