Abstract: The development and extension of large cities induced
a need for shallow tunnel in soft ground of building areas. Estimation
of ground settlement caused by the tunnel excavation is important
engineering point. In this paper, prediction of surface subsidence
caused by tunneling in one section of seventh line of Tehran subway
is considered. On the basis of studied geotechnical conditions of the
region, tunnel with the length of 26.9km has been excavated applying
a mechanized method using an EPB-TBM with a diameter of 9.14m.
In this regard, settlement is estimated utilizing both analytical and
numerical finite element method. The numerical method shows that
the value of settlement in this section is 5cm. Besides, the analytical
consequences (Bobet and Loganathan-Polous) are 5.29 and 12.36cm,
respectively. According to results of this study, due tosaturation of
this section, there are good agreement between Bobet and numerical
methods. Therefore, tunneling processes in this section needs a
special consolidation measurement and support system before the
passage of tunnel boring machine.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: This paper introduces a new variable step-size APA with decorrelation of AR input process is based on the MSD analysis. To achieve a fast convergence rate and a small steady-state estimation error, he proposed algorithm uses variable step size that is determined by minimising the MSD. In addition, experimental results show that the proposed algorithm is achieved better performance than the other algorithms.
Abstract: The need to evaluate and understand the natural
drainage pattern in a flood prone, and fast developing environment is
of paramount importance. This information will go a long way to
help the town planners to determine the drainage pattern, road
networks and areas where prominent structures are to be located. This
research work was carried out with the aim of studying the Bayelsa
landscape topography using digitized topographic information, and to
model the natural drainage flow pattern that will aid the
understanding and constructions of workable drainages. To achieve
this, digitize information of elevation and coordinate points were
extracted from a global imagery map. The extracted information was
modeled into 3D surfaces. The result revealed that the average
elevation for Bayelsa State is 12 m above sea level. The highest
elevation is 28 m, and the lowest elevation 0 m, along the coastline.
In Yenagoa the capital city of Bayelsa were a detail survey was
carried out showed that average elevation is 15 m, the highest
elevation is 25 m and lowest is 3 m above the mean sea level. The
regional elevation in Bayelsa, showed a gradation decrease from the
North Eastern zone to the South Western Zone. Yenagoa showed an
observed elevation lineament, were low depression is flanked by high
elevation that runs from the North East to the South west. Hence,
future drainages in Yenagoa should be directed from the high
elevation, from South East toward the North West and from the
North West toward South East, to the point of convergence which is
at the center that flows from South East toward the North West.
Bayelsa when considered on a regional Scale, the flow pattern is from
the North East to the South West, and also North South. It is
recommended that in the event of any large drainage construction at
municipal scale, it should be directed from North East to the South
West or from North to South. Secondly, detail survey should be
carried out to ascertain the local topography and the drainage pattern
before the design and construction of any drainage system in any part
of Bayelsa.
Abstract: Training neural networks to capture an intrinsic
property of a large volume of high dimensional data is a difficult
task, as the training process is computationally expensive. Input
attributes should be carefully selected to keep the dimensionality of
input vectors relatively small.
Technical indexes commonly used for stock market prediction
using neural networks are investigated to determine its effectiveness
as inputs. The feed forward neural network of Levenberg-Marquardt
algorithm is applied to perform one step ahead forecasting of
NASDAQ and Dow stock prices.
Abstract: Air emissions from waste treatment plants often
consist of a combination of Volatile Organic Compounds (VOCs)
and odors. Hydrogen sulfide is one of the major odorous gases
present in the waste emissions coming from municipal wastewater
treatment facilities. Hydrogen sulfide (H2S) is odorous, highly toxic
and flammable. Exposure to lower concentrations can result in eye
irritation, a sore throat and cough, shortness of breath, and fluid in
the lungs. Biofiltration has become a widely accepted technology for
treating air streams containing H2S. When compared with other nonbiological
technologies, biofilter is more cost-effective for treating large
volumes of air containing low concentrations of biodegradable compounds.
Optimization of biofilter media is essential for many reasons such as:
providing a higher surface area for biofilm growth, low pressure drop,
physical stability, and good moisture retention. In this work, a novel
biofilter media is developed and tested at a pumping station of a
municipality located in the United Arab Emirates (UAE). The
media is found to be very effective (>99%) in removing H2S
concentrations that are expected in pumping stations under steady
state and shock loading conditions.
Abstract: Society has grown to rely on Internet services, and the
number of Internet users increases every day. As more and more
users become connected to the network, the window of opportunity
for malicious users to do their damage becomes very great and
lucrative. The objective of this paper is to incorporate different
techniques into classier system to detect and classify intrusion from
normal network packet. Among several techniques, Steady State
Genetic-based Machine Leaning Algorithm (SSGBML) will be used
to detect intrusions. Where Steady State Genetic Algorithm (SSGA),
Simple Genetic Algorithm (SGA), Modified Genetic Algorithm and
Zeroth Level Classifier system are investigated in this research.
SSGA is used as a discovery mechanism instead of SGA. SGA
replaces all old rules with new produced rule preventing old good
rules from participating in the next rule generation. Zeroth Level
Classifier System is used to play the role of detector by matching
incoming environment message with classifiers to determine whether
the current message is normal or intrusion and receiving feedback
from environment. Finally, in order to attain the best results,
Modified SSGA will enhance our discovery engine by using Fuzzy
Logic to optimize crossover and mutation probability. The
experiments and evaluations of the proposed method were performed
with the KDD 99 intrusion detection dataset.
Abstract: In composting process, N high-organic wastes loss the
great part of its nitrogen as ammonia; therefore, using compost
amendments can promote the quality of compost due to the decrease
in ammonia volatilization. With regard to the effect of pH on
composting, microorganisms- activity and ammonia volatilization,
sulfuric acid and alkaline wastewater of paper mill (as liming agent
with Ca and Mg ions) were used as compost amendments. Study
results indicated that these amendments are suitable for reclamation
of compost quality properties. These held nitrogen in compost caused
to reduce C/N ratio. Both amendments had a significant effect on
total nitrogen, but it should be used sulfuric acid in fewer amounts
(20 ml/kg fresh organic wastes); and the more amounts of acid is not
proposed.
Abstract: This paper proposes a method of adaptively generating a gait pattern of biped robot. The gait synthesis is based on human's gait pattern analysis. The proposed method can easily be applied to generate the natural and stable gait pattern of any biped robot. To analyze the human's gait pattern, sequential images of the human's gait on the sagittal plane are acquired from which the gait control values are extracted. The gait pattern of biped robot on the sagittal plane is adaptively generated by a genetic algorithm using the human's gait control values. However, gait trajectories of the biped robot on the sagittal plane are not enough to construct the complete gait pattern because the biped robot moves on 3-dimension space. Therefore, the gait pattern on the frontal plane, generated from Zero Moment Point (ZMP), is added to the gait one acquired on the sagittal plane. Consequently, the natural and stable walking pattern for the biped robot is obtained.
Abstract: This study was conducted to investigate the incidence
of pathogenic bacteria: Salmonella, Shigella, Escherichia coli O157
and Staphylococcus aureus in cakes and tarts collected from thirtyfive
confectionery producing and selling premises located within
Tripoli city, Libya. The results revealed an incidence of S. aureus
with 94.4 and 48.0 %, E. coli O157 with 14.7 and 4.0 % and Salmonella
sp. with 5.9 and 8.0 % in cakes and tarts samples respectively;
while Shigella was not detected in all samples. In order to determine
the source of these pathogenic bacteria, cotton swabs were taken
from the hands of workers on the production line, the surfaces of
preparation tables and cream whipping instruments. The results
showed that the cotton swabs obtained from the hands of workers
contained S. aureus and Salmonella sp. with an incidence of 42.9 and
2.9 %, the cotton swabs obtained from the surfaces of preparation
tables 22.9 and 2.9 % and the cotton swabs obtained from the cream
whipping instruments 14.3 and 0.0 % respectively; while E. coli
O157 and Shigella sp. were not detected in all swabs. Additionally,
other bacteria were isolated from the hands of workers and the Surfaces
of producing equipments included: Aeromonas sp., Pseudomonas
sp., E. coli, Klebsiella sp., Enterobacter sp., Citrobacter sp.,
Proteus sp., Serratia sp. and Acinetobacter sp. These results indicate
that some of the cakes and tarts might pose threat to consumer's
health. Meanwhile, occurrences of pathogenic bacteria on the hands
of those who are working in production line and the surfaces of
equipments reflect poor hygienic practices at most confectionery
premises examined in this study. Thus, firm and continuous surveillance
of these premises is needed to insure the consumer's health and
safety.
Abstract: The Bangalore City is facing the acute problem of
pollution in the atmosphere due to the heavy increase in the traffic
and developmental activities in recent years. The present study is an
attempt in the direction to assess trend of the ambient air quality
status of three stations, viz., AMCO Batteries Factory, Mysore Road,
GRAPHITE INDIA FACTORY, KHB Industrial Area, Whitefield
and Ananda Rao Circle, Gandhinagar with respect to some of the
major criteria pollutants such as Total Suspended particular matter
(SPM), Oxides of nitrogen (NOx), and Oxides of sulphur (SO2). The
sites are representative of various kinds of growths viz., commercial,
residential and industrial, prevailing in Bangalore, which are
contributing to air pollution. The concentration of Sulphur Dioxide
(SO2) at all locations showed a falling trend due to use of refined
petrol and diesel in the recent years. The concentration of Oxides of
nitrogen (NOx) showed an increasing trend but was within the
permissible limits. The concentration of the Suspended particular
matter (SPM) showed the mixed trend. The correlation between
model and observed values is found to vary from 0.4 to 0.7 for SO2,
0.45 to 0.65 for NOx and 0.4 to 0.6 for SPM. About 80% of data is
observed to fall within the error band of ±50%. Forecast test for the
best fit models showed the same trend as actual values in most of the
cases. However, the deviation observed in few cases could be
attributed to change in quality of petro products, increase in the
volume of traffic, introduction of LPG as fuel in many types of
automobiles, poor condition of roads, prevailing meteorological
conditions, etc.
Abstract: In this paper we analyze the core issues affecting
software architecture in enterprise projects where a large number of
people at different backgrounds are involved and complex business,
management and technical problems exist. We first give general
features of typical enterprise projects and then present foundations of
software architectures. The detailed analysis of core issues affecting
software architecture in software development phases is given. We
focus on three main areas in each development phase: people,
process, and management related issues, structural (product) issues,
and technology related issues. After we point out core issues and
problems in these main areas, we give recommendations for
designing good architecture. We observed these core issues and the
importance of following the best software development practices and
also developed some novel practices in many big enterprise
commercial and military projects in about 10 years of experience.
Abstract: This study analyzed environmental health risks and
people-s perceptions of risks related to waste management in poor
settlements of Abidjan, to develop integrated solutions for health and
well-being improvement. The trans-disciplinary approach used relied
on remote sensing, a geographic information system (GIS),
qualitative and quantitative methods such as interviews and a
household survey (n=1800). Mitigating strategies were then
developed using an integrated participatory stakeholder workshop.
Waste management deficiencies resulting in lack of drainage and
uncontrolled solid and liquid waste disposal in the poor settlements
lead to severe environmental health risks. Health problems were
caused by direct handling of waste, as well as through broader
exposure of the population. People in poor settlements had little
awareness of health risks related to waste management in their
community and a general lack of knowledge pertaining to sanitation
systems. This unfortunate combination was the key determinant
affecting the health and vulnerability. For example, an increased
prevalence of malaria (47.1%) and diarrhoea (19.2%) was observed
in the rainy season when compared to the dry season (32.3% and
14.3%). Concerted and adapted solutions that suited all the
stakeholders concerned were developed in a participatory workshop
to allow for improvement of health and well-being.
Abstract: A new robust nonlinear control scheme of a manipulator is proposed in this paper which is robust against modeling errors and unknown disturbances. It is based on the principle of variable structure control, with sliding mode control (SMC) method. The variable structure control method is a robust method that appears to be well suited for robotic manipulators because it requers only bounds on the robotic arm parameters. But there is no single systematic procedure that is guaranteed to produce a suitable control law. Also, to reduce chattring of the control signal, we replaced the sgn function in the control law by a continuous approximation such as tangant function. We can compute the maximum load with regard to applied torque into joints. The effectivness of the proposed approach has been evaluated analitically demonstrated through computer simulations for the cases of variable load and robot arm parameters.
Abstract: In this paper, the authors take a look at advantages of
multiphase induction motors comparing them with three phase ones
and present the applications where six-phase induction motors are
used. They elaborate the mathematical model of six-phase induction
motor with two similar stator three phase winding, shifted by 30
degrees in space and three phase winding in rotor, in synchronous
reference frame for soft starting and scalar control. The authors
simulate and discuss results of speed and torque starting transients.
Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: In this paper multivariable predictive PID controller has
been implemented on a multi-inputs multi-outputs control problem
i.e., quadruple tank system, in comparison with a simple multiloop
PI controller. One of the salient feature of this system is an
adjustable transmission zero which can be adjust to operate in both
minimum and non-minimum phase configuration, through the flow
distribution to upper and lower tanks in quadruple tank system.
Stability and performance analysis has also been carried out for this
highly interactive two input two output system, both in minimum
and non-minimum phases. Simulations of control system revealed
that better performance are obtained in predictive PID design.
Abstract: The present paper presents a finite element model and
analysis for the interaction between a piezoresistive tactile sensor and
biological tissues. The tactile sensor is proposed for use in minimally
invasive surgery to deliver tactile information of biological tissues to
surgeons. The proposed sensor measures the relative hardness of soft
contact objects as well as the contact force. Silicone rubbers were
used as the phantom of biological tissues. Finite element analysis of
the silicone rubbers and the mechanical structure of the sensor were
performed using COMSOL Multiphysics (v3.4) environment. The
simulation results verify the capability of the sensor to be used to
differentiate between different kinds of silicone rubber materials.
Abstract: Complexity, as a theoretical background has made it
easier to understand and explain the features and dynamic behavior
of various complex systems. As the common theoretical background
has confirmed, borrowing the terminology for design from the
natural sciences has helped to control and understand urban
complexity. Phenomena like self-organization, evolution and
adaptation are appropriate to describe the formerly inaccessible
characteristics of the complex environment in unpredictable bottomup
systems. Increased computing capacity has been a key element in
capturing the chaotic nature of these systems.
A paradigm shift in urban planning and architectural design has
forced us to give up the illusion of total control in urban
environment, and consequently to seek for novel methods for
steering the development. New methods using dynamic modeling
have offered a real option for more thorough understanding of
complexity and urban processes. At best new approaches may renew
the design processes so that we get a better grip on the complex
world via more flexible processes, support urban environmental
diversity and respond to our needs beyond basic welfare by liberating
ourselves from the standardized minimalism.
A complex system and its features are as such beyond human
ethics. Self-organization or evolution is either good or bad. Their
mechanisms are by nature devoid of reason. They are common in
urban dynamics in both natural processes and gas. They are features
of a complex system, and they cannot be prevented. Yet their
dynamics can be studied and supported.
The paradigm of complexity and new design approaches has been
criticized for a lack of humanity and morality, but the ethical
implications of scientific or computational design processes have not
been much discussed. It is important to distinguish the (unexciting)
ethics of the theory and tools from the ethics of computer aided
processes based on ethical decisions. Urban planning and architecture
cannot be based on the survival of the fittest; however, the natural
dynamics of the system cannot be impeded on grounds of being
“non-human".
In this paper the ethical challenges of using the dynamic models
are contemplated in light of a few examples of new architecture and
dynamic urban models and literature. It is suggested that ethical
challenges in computational design processes could be reframed
under the concepts of responsibility and transparency.
Abstract: The segmentation of endovascular tools in fluoroscopy images can be accurately performed automatically or by minimum user intervention, using known modern techniques. It has been proven in literature, but no clinical implementation exists so far because the computational time requirements of such technology have not yet been met. A classical segmentation scheme is composed of edge enhancement filtering, line detection, and segmentation. A new method is presented that consists of a vector that propagates in the image to track an edge as it advances. The filtering is performed progressively in the projected path of the vector, whose orientation allows for oriented edge detection, and a minimal image area is globally filtered. Such an algorithm is rapidly computed and can be implemented in real-time applications. It was tested on medical fluoroscopy images from an endovascular cerebral intervention. Ex- periments showed that the 2D tracking was limited to guidewires without intersection crosspoints, while the 3D implementation was able to cope with such planar difficulties.