Abstract: Currently, there are many local area industrial networks
that can give guaranteed bandwidth to synchronous traffic, particularly
providing CBR channels (Constant Bit Rate), which allow
improved bandwidth management. Some of such networks operate
over Ethernet, delivering channels with enough capacity, specially
with compressors, to integrate multimedia traffic in industrial monitoring
and image processing applications with many sources. In
these industrial environments where a low latency is an essential
requirement, JPEG is an adequate compressing technique but it
generates VBR traffic (Variable Bit Rate). Transmitting VBR traffic
in CBR channels is inefficient and current solutions to this problem
significantly increase the latency or further degrade the quality. In
this paper an R(q) model is used which allows on-line calculation of
the JPEG quantification factor. We obtained increased quality, a lower
requirement for the CBR channel with reduced number of discarded
frames along with better use of the channel bandwidth.
Abstract: This paper deals with efficient computation of
probability coefficients which offers computational simplicity as
compared to spectral coefficients. It eliminates the need of inner
product evaluations in determination of signature of a combinational
circuit realizing given Boolean function. The method for computation
of probability coefficients using transform matrix, fast transform
method and using BDD is given. Theoretical relations for achievable
computational advantage in terms of required additions in computing
all 2n probability coefficients of n variable function have been
developed. It is shown that for n ≥ 5, only 50% additions are needed
to compute all probability coefficients as compared to spectral
coefficients. The fault detection techniques based on spectral
signature can be used with probability signature also to offer
computational advantage.
Abstract: The equilibrium chemical reactions taken place in a converter reactor of the Khorasan Petrochemical Ammonia plant was studied using the minimization of Gibbs free energy method. In the minimization of the Gibbs free energy function the Davidon– Fletcher–Powell (DFP) optimization procedure using the penalty terms in the well-defined objective function was used. It should be noted that in the DFP procedure along with the corresponding penalty terms the Hessian matrices for the composition of constituents in the Converter reactor can be excluded. This, in fact, can be considered as the main advantage of the DFP optimization procedure. Also the effect of temperature and pressure on the equilibrium composition of the constituents was investigated. The results obtained in this work were compared with the data collected from the converter reactor of the Khorasan Petrochemical Ammonia plant. It was concluded that the results obtained from the method used in this work are in good agreement with the industrial data. Notably, the algorithm developed in this work, in spite of its simplicity, takes the advantage of short computation and convergence time.
Abstract: In this paper we present a system for classifying videos
by frequency spectra. Many videos contain activities with repeating
movements. Sports videos, home improvement videos, or videos
showing mechanical motion are some example areas. Motion of these
areas usually repeats with a certain main frequency and several side
frequencies. Transforming repeating motion to its frequency domain
via FFT reveals these frequencies. Average amplitudes of frequency
intervals can be seen as features of cyclic motion. Hence determining
these features can help to classify videos with repeating movements.
In this paper we explain how to compute frequency spectra for video
clips and how to use them for classifying. Our approach utilizes series
of image moments as a function. This function again is transformed
into its frequency domain.
Abstract: One major difficulty that faces developers of
concurrent and distributed software is analysis for concurrency based
faults like deadlocks. Petri nets are used extensively in the
verification of correctness of concurrent programs. ECATNets [2] are
a category of algebraic Petri nets based on a sound combination of
algebraic abstract types and high-level Petri nets. ECATNets have
'sound' and 'complete' semantics because of their integration in
rewriting logic [12] and its programming language Maude [13].
Rewriting logic is considered as one of very powerful logics in terms
of description, verification and programming of concurrent systems.
We proposed in [4] a method for translating Ada-95 tasking
programs to ECATNets formalism (Ada-ECATNet). In this paper,
we show that ECATNets formalism provides a more compact
translation for Ada programs compared to the other approaches based
on simple Petri nets or Colored Petri nets (CPNs). Such translation
doesn-t reduce only the size of program, but reduces also the number
of program states. We show also, how this compact Ada-ECATNet
may be reduced again by applying reduction rules on it. This double
reduction of Ada-ECATNet permits a considerable minimization of
the memory space and run time of corresponding Maude program.
Abstract: In this paper, we propose a novel algorithm for
delineating the endocardial wall from a human heart ultrasound scan.
We assume that the gray levels in the ultrasound images are
independent and identically distributed random variables with
different Rician Inverse Gaussian (RiIG) distributions. Both synthetic
and real clinical data will be used for testing the algorithm. Algorithm
performance will be evaluated using the expert radiologist evaluation
of a soft copy of an ultrasound scan during the scanning process and
secondly, doctor’s conclusion after going through a printed copy of
the same scan. Successful implementation of this algorithm should
make it possible to differentiate normal from abnormal soft tissue and
help disease identification, what stage the disease is in and how best
to treat the patient. We hope that an automated system that uses this
algorithm will be useful in public hospitals especially in Third World
countries where problems such as shortage of skilled radiologists and
shortage of ultrasound machines are common. These public hospitals
are usually the first and last stop for most patients in these countries.
Abstract: In this report, an OTA which is used in fully
differential pipelined ADC was described. Using gain-boost
architecture with difference-ended amplifier, this OTA achieve
high-gain and high-speed. Besides, the CMFB circuit is also used, and
some methods are concerned to improve the performance. Then, by
optimization the layout design, OTA-s mismatch was reduced. This
design was using TSMC 0.18um CMOS process and simulation both
schematic and layout in Cadence. The result of the simulation shows
that the OTA has a gain up to 80dB,a unity gain bandwidth of about
1.437GHz for a 2pF load, a slew rate is about 428V/μs, a output swing
is 0.2V~1.35V, with the power supply of 1.8V, the power
consumption is 88mW. This amplifier was used in a 10bit 150MHz
pipelined ADC.
Abstract: Wavelength multiplexing (WDM) technology along
with optical amplifiers is used for optical communication systems in
S-band, C-band and L-band. To improve the overall system
performance Hybrid amplifiers consisting of cascaded TDFA and
EDFA with different gain bandwidths are preferred for long haul
wavelength multiplexed optical communication systems. This paper
deals with statistical analysis of different configuration of hybrid
amplifier i.e. analysis of TDFA-EDFA configuration and EDFA –
TDFA configuration. In this paper One-Way ANOVA method is used
for statistical analysis.
Abstract: Monitoring the tool flank wear without affecting the
throughput is considered as the prudent method in production
technology. The examination has to be done without affecting the
machining process. In this paper we proposed a novel work that is
used to determine tool flank wear by observing the sound signals
emitted during the turning process. The work-piece material we used
here is steel and aluminum and the cutting insert was carbide
material. Two different cutting speeds were used in this work. The
feed rate and the cutting depth were constant whereas the flank wear
was a variable. The emitted sound signal of a fresh tool (0 mm flank
wear) a slightly worn tool (0.2 -0.25 mm flank wear) and a severely
worn tool (0.4mm and above flank wear) during turning process were
recorded separately using a high sensitive microphone. Analysis
using Singular Value Decomposition was done on these sound
signals to extract the feature sound components. Observation of the
results showed that an increase in tool flank wear correlates with an
increase in the values of SVD features produced out of the sound
signals for both the materials. Hence it can be concluded that wear
monitoring of tool flank during turning process using SVD features
with the Fuzzy C means classification on the emitted sound signal is
a potential and relatively simple method.
Abstract: Prediction of fault-prone modules provides one way to
support software quality engineering. Clustering is used to determine
the intrinsic grouping in a set of unlabeled data. Among various
clustering techniques available in literature K-Means clustering
approach is most widely being used. This paper introduces K-Means
based Clustering approach for software finding the fault proneness of
the Object-Oriented systems. The contribution of this paper is that it
has used Metric values of JEdit open source software for generation
of the rules for the categorization of software modules in the
categories of Faulty and non faulty modules and thereafter
empirically validation is performed. The results are measured in
terms of accuracy of prediction, probability of Detection and
Probability of False Alarms.
Abstract: A numerical investigation of surface heat transfer
characteristics of turbulent air flows in different parallel plate
grooved channels is performed using CFD code. The results are
obtained for Reynolds number ranging from 10,000 to 30,000 and for
arc-shaped and rectangular grooved channels. The influence of
different geometric parameters of dimples as well as the number of
them and the geometric and thermophysical properties of channel
walls are studied. It is found that there exists an optimum value for
depth of dimples in which the largest wall heat flux can be achieved.
Also, the results show a critical value for the ratio of wall thermal
conductivity to the one of fluid in which the dependence of wall heat
flux to this ratio almost vanishes. In most cases examined, heat
transfer enhancement is larger for arc-shaped grooved channels than
rectangular ones.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: The objective of the research was to evaluate the
quality of milk pomade sweet – sherbet packed in different packaging
materials (Multibarrier 60, met.BOPET/PE, Aluthen), by several
packaging technologies – active and modified atmosphere (MAP)
(consisting of 100% CO2), and control – in air ambiance.
Experiments were carried out at the Faculty of Food Technology of
Latvia University of Agriculture. Samples were stored at the room
temperature +21±1 °C. The physiochemical properties – weight
losses, moisture, hardening, colour and changes in headspace
atmosphere concentration (CO2 and O2) of packs were analysed
before packaging and after 2, 4, 6, 8, 10 and 12 storage weeks.
Abstract: Abrasive waterjet is a novel machining process capable of processing wide range of hard-to-machine materials. This research addresses modeling and optimization of the process parameters for this machining technique. To model the process a set of experimental data has been used to evaluate the effects of various parameter settings in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. Depth of cut, as one of the most important output characteristics, has been evaluated based on different parameter settings. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. The pairwise effects of process parameters settings on process response outputs are also shown graphically. The proposed model is then embedded into a Simulated Annealing algorithm to optimize the process parameters. The optimization is carried out for any desired values of depth of cut. The objective is to determine proper levels of process parameters in order to obtain a certain level of depth of cut. Computational results demonstrate that the proposed solution procedure is quite effective in solving such multi-variable problems.
Abstract: In this work we investigated the behavior of methane
hydrates dispersed in crude oils from different fields at temperatures
below 0°C. In case of crude oil emulsion the size of water droplets is
in the range of 50e100"m. The size of hydrate particles formed from
droplets is the same. The self-preservation is not expected in this
field. However, the self-preservation of hydrates with the size of
particles 24±18"m (electron microscopy data) in suspensions is
observed. Similar results were obtained for four different kinds of
crude oil and model system such as asphaltenes, resins and wax in ndecane.
This result can allow developing effective methods to prevent
the formation and elimination of gas-hydrate plugs in pipelines under
low temperature conditions (e. g. in Eastern Siberia). There is a
prospective to use experiment results for working out the technology
of associated petroleum gas recovery.
Abstract: This paper presents a sensing system for 3D sensing
and mapping by a tracked mobile robot with an arm-type sensor
movable unit and a laser range finder (LRF). The arm-type sensor
movable unit is mounted on the robot and the LRF is installed at the
end of the unit. This system enables the sensor to change position and
orientation so that it avoids occlusions according to terrain by this
mechanism. This sensing system is also able to change the height of
the LRF by keeping its orientation flat for efficient sensing. In this kind
of mapping, it may be difficult for moving robot to apply mapping
algorithms such as the iterative closest point (ICP) because sets of the
2D data at each sensor height may be distant in a common surface. In
order for this kind of mapping, the authors therefore applied
interpolation to generate plausible model data for ICP. The results of
several experiments provided validity of these kinds of sensing and
mapping in this sensing system.
Abstract: We present a dual-band (Cellular & PCS) dual-path
zero-IF receiver for CDMA2000 diversity, monitoring and
simultaneous-GPS. The secondary path is a SAW-less diversity
CDMA receiver which can be also used for advanced features like
monitoring when supported with an additional external VCO. A GPS
receiver is integrated with its dedicated VCO allowing simultaneous
positioning during a cellular call. The circuit is implemented in a
0.25μm 40GHz-fT BiCMOS process and uses a HVQFN 56-pin
package. It consumes a maximum 300mW from a 2.8V supply in
dual-modes. The chip area is 12.8mm2.
Abstract: This paper considers a scheduling problem in flexible
flow shops environment with the aim of minimizing two important
criteria including makespan and cumulative tardiness of jobs. Since
the proposed problem is known as an Np-hard problem in literature,
we have to develop a meta-heuristic to solve it. We considered
general structure of Genetic Algorithm (GA) and developed a new
version of that based on Data Envelopment Analysis (DEA). Two
objective functions assumed as two different inputs for each Decision
Making Unit (DMU). In this paper we focused on efficiency score of
DMUs and efficient frontier concept in DEA technique. After
introducing the method we defined two different scenarios with
considering two types of mutation operator. Also we provided an
experimental design with some computational results to show the
performance of algorithm. The results show that the algorithm
implements in a reasonable time.
Abstract: Public bus service plays a significant role in our
society as people movers and to facilitate travels within towns and districts. The quality of service of public bus is always being
regarded as poor, or rather, underestimated as second class means of transportation. Reliability of service, or the ability to deliver service as planned, is one key element in perceiving the quality of bus service and the punctuality index is one of the performance parameters in determining the service reliability. This study
concentrates on evaluating the reliability performance of bus operation using punctuality index assessment. A week data for each
of six city bus routes is recorded using the on-board methodology to calculate the punctuality index for city bus service in Kota Bharu. The results revealed that the punctuality index for the whole city bus network is 94.25% (LOS B).
Abstract: Technology assessment is a vital part of decision process in manufacturing, particularly for decisions on selection of new sustainable manufacturing processes. To assess these processes, a matrix approach is introduced and sustainability assessment models are developed. Case studies show that the matrix-based approach provides a flexible and practical way for sustainability evaluation of new manufacturing technologies such as those used in surface coating. The technology assessment of coating processes reveals that compared with powder coating, the sol-gel coating can deliver better technical, economical and environmental sustainability with respect to the selected sustainability evaluation criteria for a decorative coating application of car wheels.