Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: This study was conducted using the data collected at the mouth of Jen-Gen River to investigate and analyze chromium (Cr) contained in the sediments, and to evaluate the accumulation of Cr and the degree of its potential risk. The results show that samples collected at all monitoring stations near the mouth of Jen-Gen River contain 92–567 mg/kg of Cr with average of 366±166 mg/kg. The spatial distribution of Cr reveals that the Cr concentration is relatively high in the river mouth region, and gradually diminishes toward the harbor region. This indicates that upstream industrial and municipal wastewater discharges along the river bank are major sources of pollution. The accumulation factor and potential ecological risk index indicate that the sedimentation at Jen-Gen River mouth has the most serious degree of Cr accumulation and the highest ecological potential risk.
Abstract: According to dramatic growth of internet services, an easy and prompt service deployment has been important for internet service providers to successfully maintain time-to-market. Before global service deployment, they have to pay the big cost for service evaluation to make a decision of the proper system location, system scale, service delay and so on. But, intra-Lab evaluation tends to have big gaps in the measured data compared with the realistic situation, because it is very difficult to accurately expect the local service environment, network congestion, service delay, network bandwidth and other factors. Therefore, to resolve or ease the upper problems, we propose multiple cloud based GPES Broker system and use case that helps internet service providers to alleviate the above problems in beta release phase and to make a prompt decision for their service launching. By supporting more realistic and reliable evaluation information, the proposed GPES Broker system saves the service release cost and enables internet service provider to make a prompt decision about their service launching to various remote regions.
Abstract: Interpolated contour maps drawn for aluminum,
copper and molybdenum in downstream monitoring boreholes of
water dam in Miduk Copper Complex and the values of pH, redox
potential (Eh) and distance from water dam indicate different trends
of variation and behavior of these three elements in downward
groundwater resources. As these maps exhibit, aluminum is dominant
in the most alkaline (pH = 9-11) borehole (MB5) to water dam. The
highest concentration of molybdenum is found in the nearest
borehole (MB6) to water dam. Main concentration of copper is
observed in the most oxidized borehole (MB3 with Eh=293.2mV).
The spatial difference among sampling stations can be attributed to
the existence of faults and diaclases in the geologic structure of
Miduk region which causes the groundwater sampling sites to be
impressed by different contamination sources (toe seepage and upper
seepage water originated from different zones of tailings dump).
Abstract: A novel feature selection strategy to improve the recognition accuracy on the faces that are affected due to nonuniform illumination, partial occlusions and varying expressions is proposed in this paper. This technique is applicable especially in scenarios where the possibility of obtaining a reliable intra-class probability distribution is minimal due to fewer numbers of training samples. Phase congruency features in an image are defined as the points where the Fourier components of that image are maximally inphase. These features are invariant to brightness and contrast of the image under consideration. This property allows to achieve the goal of lighting invariant face recognition. Phase congruency maps of the training samples are generated and a novel modular feature selection strategy is implemented. Smaller sub regions from a predefined neighborhood within the phase congruency images of the training samples are merged to obtain a large set of features. These features are arranged in the order of increasing distance between the sub regions involved in merging. The assumption behind the proposed implementation of the region merging and arrangement strategy is that, local dependencies among the pixels are more important than global dependencies. The obtained feature sets are then arranged in the decreasing order of discriminating capability using a criterion function, which is the ratio of the between class variance to the within class variance of the sample set, in the PCA domain. The results indicate high improvement in the classification performance compared to baseline algorithms.
Abstract: A nonlinear model of two-beam free-electron laser
(FEL) in the absence of slippage is presented. The two beams are
assumed to be cold with different energies and the fundamental
resonance of the higher energy beam is at the third harmonic of lower
energy beam. By using Maxwell-s equations and full Lorentz force
equations of motion for the electron beams, coupled differential
equations are derived and solved numerically by the fourth order
Runge–Kutta method. In this method a considerable growth of third
harmonic electromagnetic field in the XUV and X-ray regions is
predicted.
Abstract: Iris-based biometric authentication is gaining importance
in recent times. Iris biometric processing however, is a complex
process and computationally very expensive. In the overall processing
of iris biometric in an iris-based biometric authentication system,
feature processing is an important task. In feature processing, we extract
iris features, which are ultimately used in matching. Since there
is a large number of iris features and computational time increases
as the number of features increases, it is therefore a challenge to
develop an iris processing system with as few as possible number of
features and at the same time without compromising the correctness.
In this paper, we address this issue and present an approach to feature
extraction and feature matching process. We apply Daubechies D4
wavelet with 4 levels to extract features from iris images. These
features are encoded with 2 bits by quantizing into 4 quantization
levels. With our proposed approach it is possible to represent an
iris template with only 304 bits, whereas existing approaches require
as many as 1024 bits. In addition, we assign different weights to
different iris region to compare two iris templates which significantly
increases the accuracy. Further, we match the iris template based on
a weighted similarity measure. Experimental results on several iris
databases substantiate the efficacy of our approach.
Abstract: The purpose of this work is to present the potential of
solar energy in Zarqa region. The solar radiation along year 2009 was
obtained from Pyranometer which measures the global radiation over
horizontal surfaces. Solar data in several different forms, over period
of 5 minutes, hour-by-hour, daily and monthly data radiation have
been presented. Briefly, the yearly global solar radiation in Zarqa is
7297.5 MJ/m2 (2027 kWh/m²) and the average annual solar radiation
per day is 20 MJ/m2 (5.5 Kwh/m2). More specifically, the average
annual solar radiation per day is 12.9 MJ/m2 (3.57 Kwh/m2) in winter
and 25 MJ/m2 (7 Kwh/m2) in summer.
Abstract: Constant amplitude fatigue crack growth (FCG) tests
were performed on dissimilar metal welded plates of Type 316L
Stainless Steel (SS) and IS 2062 Grade A Carbon steel (CS). The
plates were welded by TIG welding using SS E309 as electrode. FCG
tests were carried on the Side Edge Notch Tension (SENT)
specimens of 5 mm thickness, with crack initiator (notch) at base
metal region (BM), weld metal region (WM) and heat affected zones
(HAZ). The tests were performed at a test frequency of 10 Hz and at
load ratios (R) of 0.1 & 0.6. FCG rate was found to increase with
stress ratio for weld metals and base metals, where as in case of
HAZ, FCG rates were almost equal at high ΔK. FCG rate of HAZ of
stainless steel was found to be lowest at low and high ΔK. At
intermediate ΔK, WM showed the lowest FCG rate. CS showed
higher crack growth rate at all ΔK. However, the scatter band of data
was found to be narrow. Fracture toughness (Kc) was found to vary
in different locations of weldments. Kc was found lowest for the
weldment and highest for HAZ of stainless steel. A novel method of
characterizing the FCG behavior using an Infrared thermography
(IRT) camera was attempted. By monitoring the temperature rise at
the fast moving crack tip region, the amount of plastic deformation
was estimated.
Abstract: Innovations and innovative activity get the increasing
value for successful financial and economic activity of the countries
and regions. The level of innovative sphere development determines
place of a country or a region in world economy and forms a basis of
steady economic growth. This article is devoted to different aspects
of organization of the national economic safety in the conditions of
innovative development, its problems, risks and threats. Economy
can be considered as aspiring for transition to innovative way only
with finding of economic safety: financial independence, power
stability and technological progress. There are statistical indicators,
defining the level of economic security and factors, threatening
economic safety of the state. The research is based on the analysis of
factors and indicators in conditions of innovative development. The
paper is illustrated by the examples of possible estimated system of
the economic safety level.
Abstract: The sequential morphologic changes of rabbit duodenal mucosa-submucosa were studied from primodial stage to birth in 15 fetuses and during the early days of life in 21 rabbit newborns till maturity using light, scanning and transmission electron microscopy. Fetal rabbit duodenum develops from a simple tube of stratified epithelium to a tube containing villus and intervillus regions of simple columnar epithelium. By day 21 of gestation, the first rudimentary villi were appeared and by day 24 the first true villi were appeared. The Crypts of Lieberkuhn did not appear until birth. By the first day of postnatal life the duodenal glands appeared. The histological maturity of the rabbit small intestine occurred one month after birth. In conclusion, at all stages, the sequential morphologic changes of the rabbit small intestine developed to meet the structural and physiological demands during the fetal stage to be prepared to extra uterine life.
Abstract: In the present paper, Fatigue life assessment of an
anti-roll bar component of a passenger vehicle, is investigated by
ANSYS 11 software. A stress analysis is also carried out by the
finite element technique for the determination of highly stressed
regions on the bar. Anti-roll bar is a suspension element used at the
front, rear, or at both ends of a car that reduces body roll by resisting
any unequal vertical motion between the pair of wheels to which it is
connected. As a first stage, fatigue damage models proposed by some
well-known references and the corresponding assumptions are
discussed and some enhancements are proposed. Then, fracture
analysis of an anti-roll bar of an automobile is carried out. The
analysed type of the anti-roll bar is especially important as many
cases are reported about the fracture after a 100,000 km of travel
fatigue and fracture conditions. This paper demonstrates fatigue life
of an anti-roll bar and then evaluated by experimental analytically
results from other researcher.
Abstract: Subsonic wind tunnel experiments were conducted to
study the effect of tripped boundary layer on the pressure distribution
in the contraction region of the tunnel. Measurements were
performed by installing trip strip at two different positions in the
concave portion of the contraction. The results show that installation
of the trip strips, have significant effects on both turbulence and
pressure distribution. The reduction in the free stream turbulence and
reduction of the wall static pressure distribution deferred signified
with the location of the trip strip.
Abstract: Temperature, humidity and precipitation in an area,
are parameters proved influential in the climate of that area, and one
should recognize them so that he can determine the climate of that
area. Climate changes are of primary importance in climatology, and
in recent years, have been of great concern to researchers and even
politicians and organizations, for they can play an important role in
social, political and economic activities. Even though the real cause
of climate changes or their stability is not yet fully recognized, they
are a matter of concern to researchers and their importance for
countries has prompted them to investigate climate changes in
different levels, especially in regional, national and continental level.
This issue has less been investigated in our country. However, in
recent years, there have been some researches and conferences on
climate changes. This study is also in line with such researches and
tries to investigate and analyze the trends of climate changes
(temperature and precipitation) in Sefid-roud (the name of a river)
basin. Three parameters of mean annual precipitation, temperature,
and maximum and minimum temperatures in 36 synoptic and
climatology stations in a statistical period of 49 years (1956-2005) in
the stations of Sefid-roud basin were analyzed by Mann-Kendall test.
The results obtained by data analysis show that climate changes are
short term and have a trend. The analysis of mean temperature
revealed that changes have a significantly rising trend, besides the
precipitation has a significantly falling trend.
Abstract: Aggressive scaling of MOS devices requires use of ultra-thin gate oxides to maintain a reasonable short channel effect and to take the advantage of higher density, high speed, lower cost etc. Such thin oxides give rise to high electric fields, resulting in considerable gate tunneling current through gate oxide in nano regime. Consequently, accurate analysis of gate tunneling current is very important especially in context of low power application. In this paper, a simple and efficient analytical model has been developed for channel and source/drain overlap region gate tunneling current through ultra thin gate oxide n-channel MOSFET with inevitable deep submicron effect (DSME).The results obtained have been verified with simulated and reported experimental results for the purpose of validation. It is shown that the calculated tunnel current is well fitted to the measured one over the entire oxide thickness range. The proposed model is suitable enough to be used in circuit simulator due to its simplicity. It is observed that neglecting deep sub-micron effect may lead to large error in the calculated gate tunneling current. It is found that temperature has almost negligible effect on gate tunneling current. It is also reported that gate tunneling current reduces with the increase of gate oxide thickness. The impact of source/drain overlap length is also assessed on gate tunneling current.
Abstract: A numerical study of flow in a horizontally channel
partially filled with a porous screen with non-uniform inlet has been
performed by lattice Boltzmann method (LBM). The flow in porous
layer has been simulated by the Brinkman-Forchheimer model.
Numerical solutions have been obtained for variable porosity models
and the effects of Darcy number and porosity have been studied in
detail. It is found that the flow stabilization is reliant on the Darcy
number. Also the results show that the stabilization of flow field and
heat transfer is depended to Darcy number. Distribution of stream
field becomes more stable by decreasing Darcy number. Results
illustrate that the effect of variable porosity is significant just in the
region of the solid boundary. In addition, difference between constant
and variable porosity models is decreased by decreasing the Darcy
number.
Abstract: This paper investigates the problem of tracking spa¬tiotemporal changes of a satellite image through the use of Knowledge Discovery in Database (KDD). The purpose of this study is to help a given user effectively discover interesting knowledge and then build prediction and decision models. Unfortunately, the KDD process for spatiotemporal data is always marked by several types of imperfections. In our paper, we take these imperfections into consideration in order to provide more accurate decisions. To achieve this objective, different KDD methods are used to discover knowledge in satellite image databases. Each method presents a different point of view of spatiotemporal evolution of a query model (which represents an extracted object from a satellite image). In order to combine these methods, we use the evidence fusion theory which considerably improves the spatiotemporal knowledge discovery process and increases our belief in the spatiotemporal model change. Experimental results of satellite images representing the region of Auckland in New Zealand depict the improvement in the overall change detection as compared to using classical methods.
Abstract: This study presents a systematic analysis of wetted region due to cooling of aluminum plate by water spray impingement with respect to different water flow rates, spray nozzle heights, and subcooling. Unlike jet impingement, the wetting is not commenced upon spray impingement and there is a delay in wetness of hot test surface. After initiation, the wetting (black zone) progresses gradually to cover all test plate and provides efficient cooling in nucleate boiling regime. Generally, spray cooling is found function of spray flow rate, spray-to-surface distance and water subcooling. Wetting delay is decreasing by increasing of spray flow rate until spray impact area is not become bigger that test surface. Otherwise, higher spray flow rate is not practically accelerated start of wetting. Very fast wetting due to spray cooling can be obtained by dense spray (high floe rate) discharged from adjacent nozzle to the test surface. Highly subcooling water spray also triggers earlier wetting of hot aluminum plate.
Abstract: A total of twenty tensile biopsies were collected from
children undergoing tonsillectomy from teaching hospital ENT
department and Kurdistan private hospital in sulaimani city. All
biopsies were homogenized and cultured; the obtained bacterial
isolates were purified and identified by biochemical tests and VITEK
2 compact system. Among the twenty studied samples, only one
Pseudomonas putida with probability of 99% was isolated.
Antimicrobial susceptibility was carried out by disk diffusion
method, Pseudomonas putida showed resistance to all antibiotics
used except vancomycin. The isolate further subjected to PCR and
DNA sequence analysis of blaVIM gene using different set of primers
for different regions of VIM gene. The results were found to be PCR
positive for the blaVIM gene. To determine the sequence of blaVIM
gene, DNA sequencing performed. Sequence alignment of blaVIM
gene with previously recorded blaVIM gene in NCBI- database showed
that P. putida isolate have different blaVIM gene.
Abstract: A novel method of learning complex fuzzy decision regions in the n-dimensional feature space is proposed. Through the fuzzy decision regions, a given pattern's class membership value of every class is determined instead of the conventional crisp class the pattern belongs to. The n-dimensional fuzzy decision region is approximated by union of hyperellipsoids. By explicitly parameterizing these hyperellipsoids, the decision regions are determined by estimating the parameters of each hyperellipsoid.Genetic Algorithm is applied to estimate the parameters of each region component. With the global optimization ability of GA, the learned decision region can be arbitrarily complex.