Abstract: Since, it is essential to provide homeless people by the
earthquake with safe, habitable accommodation repairing medium
and slight levels of damage at the connection parts should be
undertaken. In order to prove that a repaired connection was
sufficiently strong, a precast beam to column post tensioned
connection was tested in three phases. In phase one, the middle level
damage was observed at 6% drift at these connections. As a result of
the extra loads applied, little damage was observed. In the last phase,
the four connections tested in the first phase were repaired using
epoxy resin and then retested. The results from the tests on the
repaired precast and the undamaged specimens showed that the
repaired specimens were sufficiently strong, thus proving that repair
to damaged precast beam to column post tensioned connections can
be undertaken.
Abstract: This work reports the potential of using Palm Kernel
(PK) ash and shell as a partial substitute for Portland Cement (PC)
and coarse aggregate in the development of mortar and concrete. PK
ash and shell are agro-waste materials from palm oil mills, the
disposal of PK ash and shell is an environmental problem of concern.
The PK ash has pozzolanic properties that enables it as a partial
replacement for cement and also plays an important role in the
strength and durability of concrete, its use in concrete will alleviate
the increasing challenges of scarcity and high cost of cement. In order
to investigate the PC replacement potential of PK ash, three types of
PK ash were produced at varying temperature (350-750C) and they
were used to replace up to 50% PC. The PK shell was used to replace
up to 100% coarse aggregate in order to study its aggregate
replacement potential. The testing programme included material
characterisation, the determination of compressive strength, tensile
splitting strength and chemical durability in aggressive sulfatebearing
exposure conditions. The 90 day compressive results showed
a significant strength gain (up to 26.2 N/mm2). The Portland cement
and conventional coarse aggregate has significantly higher influence
in the strength gain compared to the equivalent PK ash and PK shell.
The chemical durability results demonstrated that after a prolonged
period of exposure, significant strength losses in all the concretes
were observed. This phenomenon is explained, due to lower change
in concrete morphology and inhibition of reaction species and the
final disruption of the aggregate cement paste matrix.
Abstract: In rapid industrial development, the demand for
high-strength and lightweight materials have been increased. Thus,
various CFRP (Carbon Fiber Reinforced Plastics) with composite
materials are being used. The design variables of CFRP are its
lamination direction, order and thickness. Thus, the hardness and
strength of CFRP depends much on their design variables. In this
paper, the lamination direction of CFRP was used to produce a
symmetrical ply [0°/0°, -15°/+15°, -30°/+30°, -45°/+45°, -60°/+60°,
-75°/+75° and 90°/90°] and an asymmetrical ply [0°/15°, 0°/30°,
0°/45°, 0°/60° 0°/75° and 0°/90°]. The bending flexure stress of the
CFRP specimen was evaluated through a bending test. Its thermal
property was measured using an infrared camera. The symmetrical
specimen and the asymmetrical specimen were analyzed. The results
showed that the asymmetrical specimen increased the bending loads
according to the increase in the orientation angle; and from 0°, the
symmetrical specimen showed a tendency opposite the asymmetrical
tendency because the tensile force of fiber differs at the vertical
direction of its load. Also, the infrared camera showed that the thermal
property had a trend similar to that of the mechanical properties.
Abstract: This paper describes an analysis of Yacht Simulator
international trends and also explains about Yacht. The results are
summarized as follows. Attached to the cockpit are sensors that feed
-back information on rudder angle, boat heel angle and mainsheet
tension to the computer. Energy expenditure of the sailor measure
indirectly using expired gas analysis for the measurement of VO2 and
VCO2. At sea course configurations and wind conditions can be preset
to suit any level of sailor from complete beginner to advanced sailor.
Abstract: Generally the natural environment is made up of air,
water and soil. The release of emission of industrial waste into
anyone of the components of the environment causes pollution.
Industrial pollution significantly threatens the inherent right of
people, to the enjoyment of a safe and secure environment. The aim
of this paper is to assess the effect of environmental pollution and
health risks of residents living near Ewekoro cement factory. The
research made use of IKONOS imagery for Geographical
Information System (GIS) to buffer and extract buildings that are less
than 1km to the factory, within 1km to 5km and above 5km to the
factory. Also questionnaire was used to elicit information on the
socio-economic factors, effect of environmental pollution on
residents and measures adopted to control industrial pollution on the
residents. Findings show that most buildings that fall between less
than 1km and 1km to 5km to the factory have high health risk in the
study area. The study recommended total relocation for the residents
of the study area to reduce health risk problems.
Abstract: Geometric and mechanical properties all influence the
resistance of RC structures and may, in certain combination of
property values, increase the risk of a brittle failure of the whole
system.
This paper presents a statistical and probabilistic investigation on
the resistance of RC beams designed according to Eurocodes 2 and 8,
and subjected to multiple failure modes, under both the natural
variation of material properties and the uncertainty associated with
cross-section and transverse reinforcement geometry. A full
probabilistic model based on JCSS Probabilistic Model Code is
derived. Different beams are studied through material nonlinear
analysis via Monte Carlo simulations. The resistance model is
consistent with Eurocode 2. Both a multivariate statistical evaluation
and the data clustering analysis of outcomes are then performed.
Results show that the ultimate load behaviour of RC beams
subjected to flexural and shear failure modes seems to be mainly
influenced by the combination of the mechanical properties of both
longitudinal reinforcement and stirrups, and the tensile strength of
concrete, of which the latter appears to affect the overall response of
the system in a nonlinear way. The model uncertainty of the
resistance model used in the analysis plays undoubtedly an important
role in interpreting results.
Abstract: Waste silicon carbide (waste SiC) filled high-density
polyethylene (HDPE) with and without surface modifiers were
studied. Two types of surface modifiers namely; high-density
polyethylene-grafted-maleic anhydride (HDPE-g-MA) and 3-aminopropyltriethoxysilane have been used in this study. The
composites were produced using a two roll mill, extruder and shaped
in a hydraulic compression molding machine. The mechanical
properties of polymer composites such as flexural strength and
modulus, impact strength, tensile strength, stiffness and hardness
were investigated over a range of compositions. It was found that,
flexural strength and modulus, tensile modulus and hardness
increased, whereas impact strength and tensile strength decreased
with the increasing in filler contents, compared to the neat HDPE. At
similar filler content, the effect of both surface modifiers increased
flexural modulus, impact strength, tensile strength and stiffness but
reduced the flexural strength. Morphological investigation using
SEM revealed that the improvement in mechanical properties was
due to enhancement of the interfacial adhesion between waste SiC
and HDPE.
Abstract: The use OF adhesive anchors for wooden constructions is an efficient technology to connect and design timber members in new timber structures and to rehabilitate the damaged structural members of historical buildings. Due to the lack of standard regulation in this specific area of structural design, designers’ choices are still supported by test analysis that enables knowledge, and the prediction, of the structural behaviour of glued in rod joints. The paper outlines an experimental research activity aimed at identifying the tensile resistance capacity of several new adhesive joint prototypes made of epoxy resin, steel bar and timber, Oak and Douglas Fir species. The development of new adhesive connectors has been carried out by using epoxy to glue stainless steel bars into pre-drilled holes, characterised by smooth and rough internal surfaces, in timber samples. The realization of a threaded contact surface using a specific drill bit has led to an improved bond between wood and epoxy. The applied changes have also reduced the cost of the joints’ production. The paper presents the results of this parametric analysis and a Finite Element analysis that enables identification and study of the internal stress distribution in the proposed adhesive anchors.
Abstract: One image is worth more than thousand words.
Images if analyzed can reveal useful information. Low level image
processing deals with the extraction of specific feature from a single
image. Now the question arises: What technique should be used to
extract patterns of very large and detailed image database? The
answer of the question is: “Image Mining”. Image Mining deals with
the extraction of image data relationship, implicit knowledge, and
another pattern from the collection of images or image database. It is
nothing but the extension of Data Mining. In the following paper, not
only we are going to scrutinize the current techniques of image
mining but also present a new technique for mining images using
Genetic Algorithm.
Abstract: In this letter, we explore exact solutions for the
Horava-Lifshitz gravity. We use of an extension of this theory with
first order dynamical lapse function. The equations of motion have
been derived in a fully consistent scenario. We assume that there
are some spherically symmetric families of exact solutions of this
extended theory of gravity. We obtain exact solutions and investigate
the singularity structures of these solutions. Specially, an exact
solution with the regular horizon is found.
Abstract: The present study was undertaken to investigate the
effect of aging parameters (time and temperature) on the mechanical
properties of Be-and/or Zr- treated Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys containing Be and/or Zr. Different aging
treatment were carried out for the as solution treated (SHT)
specimens (after quenching in warm water). The specimens were
aged at different conditions; Natural and artificial aging was carried
out at room temperature, 120C, 150C, 180C and 220C for different
periods of time. Duplex aging was performed for SHT conditions
(pre-aged at different time and temperature followed by high
temperature aging). Ultimate tensile strength, yield strength and %
elongation data results as a function of different aging parameters are
analysed. A statistical design of experiments (DOE) approach using
fractional factorial design is applied to acquire an understanding of
the effects of these variables and their interactions on the mechanical
properties of Be- and/or Zr- treated 7075 alloys. Mathematical
models are developed to relate the alloy mechanical properties with
the different aging parameters.
Abstract: A novel hybrid model of the lumbar spine, allowing
fast static and dynamic simulations of the disc pressure
and the spine mobility, is introduced in this work. Our
contribution is to combine rigid bodies, deformable finite
elements, articular constraints, and springs into a unique model
of the spine. Each vertebra is represented by a rigid body
controlling a surface mesh to model contacts on the facet
joints and the spinous process. The discs are modeled using
a heterogeneous tetrahedral finite element model. The facet
joints are represented as elastic joints with six degrees of
freedom, while the ligaments are modeled using non-linear
one-dimensional elastic elements. The challenge we tackle
is to make these different models efficiently interact while
respecting the principles of Anatomy and Mechanics.
The mobility, the intradiscal pressure, the facet joint force and
the instantaneous center of rotation of the lumbar spine are
validated against the experimental and theoretical results of
the literature on flexion, extension, lateral bending as well as
axial rotation.
Our hybrid model greatly simplifies the modeling task and
dramatically accelerates the simulation of pressure within the
discs, as well as the evaluation of the range of motion and the
instantaneous centers of rotation, without penalizing precision.
These results suggest that for some types of biomechanical
simulations, simplified models allow far easier modeling and
faster simulations compared to usual full-FEM approaches
without any loss of accuracy.
Abstract: This work presents synthesis of α,ω-dithienyl
terminated poly(ethylene glycol) (PEGTh) capable for further chain
extension by either chemical or electrochemical polymeriztion.
PEGTh was characterized by FTIR and 1H-NMR. Further
copolymerization of PEGTh and pyrrole (Py) was performed by
chemical oxidative polymerization using ceric (IV) salt as an oxidant
(PPy-PEGTh). PEG without end group modification was used
directly to prepare copolymers with Py by Ce (IV) salt (PPy-PEG).
Block copolymers with mole ratio of pyrrole to PEGTh (PEG) 50:1
and 10:1 were synthesized. The electrical conductivities of
copolymers PPy-PEGTh and PPy-PEG were determined by four
point probe technique. Influence of the synthetic route and content of
the insulating segment on conductivity and yield of the copolymers
were investigated.
Abstract: In the present work, the alloy of Bismuth-lead is
prepared on the basis of percentage of molecular weight 9:1, 5:5 and
1:9 ratios and grown by Zone- Refining Technique under a vacuum
atmosphere. The EDAX of these samples are done and the results are
reported. Micro hardness test has been used as an alternative test for
measuring material’s tensile properties. The effect of temperature and
load on the hardness of the grown alloy has been studied. Further the
comparative studies of work hardening coefficients are reported.
Abstract: Clustering involves the partitioning of n objects into k
clusters. Many clustering algorithms use hard-partitioning techniques
where each object is assigned to one cluster. In this paper we propose
an overlapping algorithm MCOKE which allows objects to belong to
one or more clusters. The algorithm is different from fuzzy clustering
techniques because objects that overlap are assigned a membership
value of 1 (one) as opposed to a fuzzy membership degree. The
algorithm is also different from other overlapping algorithms that
require a similarity threshold be defined a priori which can be
difficult to determine by novice users.
Abstract: Kazakhstan is currently one of the dynamically
developing states in its region. The stable growth in all sectors of the
economy leads to a corresponding increase in energy consumption.
Thus country consumes significant amount of energy due to the high
level of industrialisation and the presence of energy-intensive
manufacturing such as mining and metallurgy which in turn leads to
low energy efficiency. With allowance for this the Government has
set several priorities to adopt a transition of Republic of Kazakhstan
to a “green economy”. This article provides an overview of
Kazakhstan’s energy efficiency situation in for the period of 1991-
2014. First, the dynamics of production and consumption of
conventional energy resources are given. Second, the potential of
renewable energy sources is summarised followed by the description
of GHG emissions trends in the country. Third, Kazakhstan’ national
initiatives, policies and locally implemented projects in the field of
energy efficiency are described.
Abstract: In this study, composites were fabricated from oil
palm empty fruit bunch fiber and poly(lactic) acid by extrusion
followed by injection moulding. Surface of the fiber was pre-treated
by ultrasound in an alkali medium and treatment efficiency was
investigated by scanning electron microscopy (SEM) analysis and
Fourier transforms infrared spectrometer (FTIR). Effect of fiber
treatment on composite was characterized by tensile strength (TS),
tensile modulus (TM) and impact strength (IS). Furthermore,
biostrong impact modifier was incorporated into the treated fiber
composite to improve its impact properties. Mechanical testing
showed an improvement of up to 23.5% and 33.6% respectively for
TS and TM of treated fiber composite above untreated fiber
composite. On the other hand incorporation of impact modifier led to
enhancement of about 20% above the initial IS of the treated fiber
composite.
Abstract: The present study was undertaken to investigate the
effect of pre-aging and aging parameters (time and temperature) on
the mechanical properties of Al-Mg-Zn (7075) alloys. Ultimate
tensile strength, 0.5% offset yield strength and % elongation
measurements were carried out on specimens prepared from cast and
heat treated 7075 alloys. Aging treatments were carried out for the as
solution treated (SHT) specimens (after quenching in warm water).
The specimens were aged at different conditions; Natural aging was
carried out at room temperature for different periods of time. Double
aging was performed for SHT conditions (pre-aged at different time
and temperature followed by high temperature aging). Ultimate
tensile strength, yield strength and % elongation as a function of
different pre-aging and aging parameters are analyzed to acquire an
understanding of the effects of these variables and their interactions
on the mechanical properties of Be-treated 7075 alloys.
Abstract: The mechanics of rip currents are complex, involving
interactions between waves, currents, water levels and the bathymetry,
that present particular challenges for numerical models. Here,
the effects of a grid-spacing dependent horizontal mixing on the
wave-current interactions are studied. Near the shore, wave rays
diverge from channels towards bar crests because of refraction by
topography and currents, in a way that depends on the rip current
intensity which is itself modulated by the horizontal mixing. At
low resolution with the grid-spacing dependent horizontal mixing,
the wave motion is the same for both coupling modes because the
wave deviation by the currents is weak. In high resolution case,
however, classical results are found with the stabilizing effect of
the flow by feedback of waves on currents. Lastly, wave-current
interactions and the horizontal mixing strongly affect the intensity
of the three-dimensional rip velocity.
Abstract: Physics Education Research (PER) results have shown
that students do not achieve the expected level of competency in
understanding the concepts of different domains of Physics learning
when taught by the traditional teaching methods, the concepts of
Electricity and Magnetism (E&M) being one among them.
Simulation being one of the valuable instructional tools renders an
opportunity to visualize varied experiences with such concepts.
Considering the electric force concept which requires extensive use
of vector representations, we report here the outcome of the research
results pertaining to the student understanding of this concept and the
role of simulation in using vector representation. The simulation
platform provides a positive impact on the use of vector
representation.
The first stage of this study involves eliciting and analyzing
student responses to questions that probe their understanding of the
concept of electrostatic force and this is followed by four stages of
student interviews as they use the interactive simulations of electric
force in one dimension. Student responses to the questions are
recorded in real time using electronic pad. A validation test interview
is conducted to evaluate students' understanding of the electric force
concept after using interactive simulation. Results indicate lack of
procedural knowledge of the vector representation. The study
emphasizes the need for the choice of appropriate simulation and
mode of induction for learning.