Abstract: This study demonstrates the feasibility of joining the commercial pure copper plates by friction stir welding (FSW). Microstructure, microhardness and tensile properties in terms of the joint efficiency were found 94.03 % compare to as receive base material (BM). The average hardness at the top was higher than bottom. Hardness of weld zone was higher than the base material. Different microstructure zones were revealed by optical microscopy and scanning electron microscopy. The stirred zone (SZ) exhibited primary two phases namely, recrystallized grains and fine precipitates in matrix of copper.
Abstract: The contribution deals with problem of take-off phase of back somersault with twisting with various numbers of twists along longitudinal body axis. The aim was to evaluate the changes in angles during transition phase from back handspring to back somersault using 3D kinematic analysis of the somersaults. We used Simi Motion System for the 3D kinematic analysis of the observed gymnastic element performed by Czech Republic female representative and 2008 Summer Olympic Games participant. The results showed that the higher the number of twists, the smaller the touchdown angle in which the gymnasts lands on the pad in the beginning of take-off phase. In back somersault with one twist (180°) the average angle is 54°, in 1080° back somersault the average angle is 45.9°. These results may help to improve technical training of sports gymnasts.
Abstract: With the long-term objective of Critical Heat Flux (CHF) prediction, a Direct Numerical Simulation (DNS) framework for simulation of subcooled and saturated nucleate pool boiling is developed. One case of saturated, and three cases of subcooled boiling at different subcooling levels are simulated. Grid refinement study is also reported. Both boiling and condensation phenomena can be computed simultaneously in the proposed numerical framework. Computed bubble detachment diameters of the saturated nucleate pool boiling cases agree well with the experiment. The flow structures around the growing bubble are presented and the accompanying physics is described. The relation between heat flux evolution from the heated wall and the bubble growth is studied, along with investigations of temperature distribution and flow field evolutions.
Abstract: The refueling of a transparent rectangular fuel tank
fitted with a standard filler pipe and roll-over valve was
experimentally studied. A fuel-conditioning cart, capable of
handling fuels of different Reid vapor pressure at a constant
temperature, was used to dispense fuel at the desired rate. The
experimental protocol included transient recording of the tank and
filler tube pressures while video recording the flow patterns in the
filler tube and tank during the refueling process. This information
was used to determine the effect of changes in the vent tube
diameter, fuel-dispense flow rate and fuel Reid vapor pressure on the
pressure-time characteristics and the occurrence of premature fuel
filling shut-off and fuel spill-back. Pressure-time curves for the case
of normal shut-off demonstrated the classic, three-phase
characteristic noted in the literature. The variation of the maximum
values of tank dome and filler tube pressures are analyzed in relation
to the occurrence of premature shut-off.
Abstract: Functional near infrared spectroscopy (fNIRS) is a
practical non-invasive optical technique to detect characteristic of
hemoglobin density dynamics response during functional activation of
the cerebral cortex. In this paper, fNIRS measurements were made in
the area of motor cortex from C4 position according to international
10-20 system. Three subjects, aged 23 - 30 years, were participated in
the experiment.
The aim of this paper was to evaluate the effects of different motor
activation tasks of the hemoglobin density dynamics of fNIRS signal.
The chaotic concept based on deterministic dynamics is an important
feature in biological signal analysis. This paper employs the chaotic
properties which is a novel method of nonlinear analysis, to analyze
and to quantify the chaotic property in the time series of the
hemoglobin dynamics of the various motor imagery tasks of fNIRS
signal. Usually, hemoglobin density in the human brain cortex is
found to change slowly in time. An inevitable noise caused by various
factors is to be included in a signal. So, principle component analysis
method (PCA) is utilized to remove high frequency component. The
phase pace is reconstructed and evaluated the Lyapunov spectrum, and
Lyapunov dimensions. From the experimental results, it can be
conclude that the signals measured by fNIRS are chaotic.
Abstract: This paper presents the 20-GHz fractional PLL (Phase
Locked Loop) circuit for the next generation Wi-Fi by using 90 nm
TSMC process. The newly suggested millimeter wave 16/17
pre-scalar is designed and verified by measurement to make the
fractional PLL having a low quantization noise. The operational
bandwidth of the 60 GHz system is 15 % of the carrier frequency
which requires large value of Kv (VCO control gain) resulting in
degradation of phase noise. To solve this problem, this paper adopts
AFC (Automatic Frequency Controller) controlled 4-bit millimeter
wave VCO with small value of Kv. Also constant Kv is implemented
using 4-bit varactor bank. The measured operational bandwidth is 18.2
~ 23.2 GHz which is 25 % of the carrier frequency. The phase noise of
-58 and -96.2 dBc/Hz at 100 KHz and 1 MHz offset is measured
respectively. The total power consumption of the PLL is only 30 mW.
Abstract: This paper introduces a novel design for boring bar with enhanced damping capability. The principle followed in the design phase was to enhance the damping capability minimizing the loss in static stiffness through implementation of composite material interfaces. The newly designed tool has been compared to a conventional tool. The evaluation criteria were the dynamic characteristics, frequency and damping ratio, of the machining system, as well as the surface roughness of the machined workpieces. The use of composite material in the design of damped tool has been demonstrated effective. Furthermore, the autoregressive moving average (ARMA) models presented in this paper take into consideration the interaction between the elastic structure of the machine tool and the cutting process and can therefore be used to characterize the machining system in operational conditions.
Abstract: AAM has been successfully applied to face alignment,
but its performance is very sensitive to initial values. In case the initial
values are a little far distant from the global optimum values, there
exists a pretty good possibility that AAM-based face alignment may
converge to a local minimum. In this paper, we propose a progressive
AAM-based face alignment algorithm which first finds the feature
parameter vector fitting the inner facial feature points of the face and
later localize the feature points of the whole face using the first
information. The proposed progressive AAM-based face alignment
algorithm utilizes the fact that the feature points of the inner part of the
face are less variant and less affected by the background surrounding
the face than those of the outer part (like the chin contour). The
proposed algorithm consists of two stages: modeling and relation
derivation stage and fitting stage. Modeling and relation derivation
stage first needs to construct two AAM models: the inner face AAM
model and the whole face AAM model and then derive relation matrix
between the inner face AAM parameter vector and the whole face
AAM model parameter vector. In the fitting stage, the proposed
algorithm aligns face progressively through two phases. In the first
phase, the proposed algorithm will find the feature parameter vector
fitting the inner facial AAM model into a new input face image, and
then in the second phase it localizes the whole facial feature points of
the new input face image based on the whole face AAM model using
the initial parameter vector estimated from using the inner feature
parameter vector obtained in the first phase and the relation matrix
obtained in the first stage. Through experiments, it is verified that the
proposed progressive AAM-based face alignment algorithm is more
robust with respect to pose, illumination, and face background than the
conventional basic AAM-based face alignment algorithm.
Abstract: System development life cycle (SDLC) is a
process uses during the development of any system. SDLC
consists of four main phases: analysis, design, implement and
testing. During analysis phase, context diagram and data flow
diagrams are used to produce the process model of a system.
A consistency of the context diagram to lower-level data flow
diagrams is very important in smoothing up developing
process of a system. However, manual consistency check from
context diagram to lower-level data flow diagrams by using a
checklist is time-consuming process. At the same time, the
limitation of human ability to validate the errors is one of the
factors that influence the correctness and balancing of the
diagrams. This paper presents a tool that automates the
consistency check between Data Flow Diagrams (DFDs)
based on the rules of DFDs. The tool serves two purposes: as
an editor to draw the diagrams and as a checker to check the
correctness of the diagrams drawn. The consistency check
from context diagram to lower-level data flow diagrams is
embedded inside the tool to overcome the manual checking
problem.
Abstract: The performance of high-resolution schemes is investigated for unsteady, inviscid and compressible multiphase flows. An Eulerian diffuse interface approach has been chosen for the simulation of multicomponent flow problems. The reduced fiveequation and seven equation models are used with HLL and HLLC approximation. The authors demonstrated the advantages and disadvantages of both seven equations and five equations models studying their performance with HLL and HLLC algorithms on simple test case. The seven equation model is based on two pressure, two velocity concept of Baer–Nunziato [10], while five equation model is based on the mixture velocity and pressure. The numerical evaluations of two variants of Riemann solvers have been conducted for the classical one-dimensional air-water shock tube and compared with analytical solution for error analysis.
Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.
Abstract: Impurity metals such as manganese and cadmium
from high-tenor cobalt electrolyte solution were selectively removed
by solvent extraction method using Co-D2EHPA after converting the functional group of D2EHPA with Co2+ ions. The process parameters
such as pH, organic concentration, O/A ratio, kinetics etc. were
investigated and the experiments were conducted by batch tests in the laboratory bench scale. Results showed that a significant amount
of manganese and cadmium can be extracted using Co-D2EHPA for the optimum processing of cobalt electrolyte solution at equilibrium pH about 3.5. The McCabe-Thiele diagram, constructed from the
extraction studies showed that 100% impurities can be extracted through four stages for manganese and three stages for cadmium
using O/A ratio of 0.65 and 1.0, respectively. From the stripping study, it was found that 100% manganese and cadmium can be stripped from the loaded organic using 0.4 M H2SO4 in a single
contact. The loading capacity of Co-D2EHPA by manganese and cadmium were also investigated with different O/A ratio as well as
with number of stages of contact of aqueous and organic phases. Valuable information was obtained for the designing of an impurities
removal process for the production of pure cobalt with less trouble in the electrowinning circuit.
Abstract: Group contribution methods such as the UNIFAC are
very useful to researchers and engineers involved in synthesis,
feasibility studies, design and optimization of separation processes.
They can be applied successfully to predict phase equilibrium and
excess properties in the development of chemical and separation
processes. The main focus of this work was to investigate the
possibility of absorbing selected volatile organic compounds (VOCs)
into polydimethylsiloxane (PDMS) using three selected UNIFAC
group contribution methods. Absorption followed by subsequent
stripping is the predominant available abatement technology of
VOCs from flue gases prior to their release into the atmosphere. The
original, modified and effective UNIFAC models were used in this
work. The thirteen selected VOCs that have been considered in this
research are: pentane, hexane, heptanes, trimethylamine, toluene,
xylene, cyclohexane, butyl acetate, diethyl acetate, chloroform,
acetone, ethyl methyl ketone and isobutyl methyl ketone. The
computation was done for solute VOC concentration of 8.55x10-8
which is well in the infinite dilution region. The results obtained in
this study compare very well with those published in literature
obtained through both measurements and predictions. The phase
equilibrium obtained in this study show that PDMS is a good
absorbent for the removal of VOCs from contaminated air streams
through physical absorption.
Abstract: In this paper, the effect of receive and/or transmit
antenna spacing on the performance (BER vs. SNR) of multipleantenna
systems is determined by using an RCS (Radar Cross
Section) channel model. In this physical model, the scatterers
existing in the propagation environment are modeled by their RCS so
that the correlation of the receive signal complex amplitudes, i.e.,
both magnitude and phase, can be estimated. The proposed RCS
channel model is then compared with classical models.
Abstract: Isobaric vapor-liquid equilibrium measurements are reported for the binary mixtures of n-Butylamine and Triethylamine with Cumene at 97.3 kPa. The measurements have been performed using a vapor recirculating type (modified Othmer's) equilibrium still. The binary mixture of n-Butylamine + Cumene shows positive deviation from ideality. Triethylamine + Cumene mixture shows negligible deviation from ideality. None of the systems form an azeotrope. The activity coefficients have been calculated taking into consideration the vapor phase nonideality. The data satisfy the thermodynamic consistency test of Herington. The activity coefficients have been satisfactorily correlated by means of the Margules, NRTL, and Black equations. The activity coefficient values obtained by the UNIFAC model are also reported.
Abstract: This paper presents the effectiveness of artificial
intelligent technique to apply for pattern recognition and
classification of Partial Discharge (PD). Characteristics of PD signal
for pattern recognition and classification are computed from the
relation of the voltage phase angle, the discharge magnitude and the
repeated existing of partial discharges by using statistical and fractal
methods. The simplified fuzzy ARTMAP (SFAM) is used for pattern
recognition and classification as artificial intelligent technique. PDs
quantities, 13 parameters from statistical method and fractal method
results, are inputted to Simplified Fuzzy ARTMAP to train system
for pattern recognition and classification. The results confirm the
effectiveness of purpose technique.
Abstract: This paper deals with the effect of a power transformer’s vector group on the basic voltage sag characteristics during unbalanced faults at a meshed or radial power network. Specifically, the propagation of voltage sags through a power transformer is studied with advanced short-circuit analysis. A smart method to incorporate this effect on analytical mathematical expressions is proposed. Based on this methodology, the positive effect of transformers of certain vector groups on the mitigation of the expected number of voltage sags per year (sag frequency) at the terminals of critical industrial customers can be estimated.
Abstract: This paper presents three-phase evolution search methodology to automatically design fuzzy logic controllers (FLCs) that can work in a wide range of operating conditions. These include varying load, parameter variations, and unknown external disturbances. The three-phase scheme consists of an exploration phase, an exploitation phase and a robustness phase. The first two phases search for FLC with high accuracy performances while the last phase aims at obtaining FLC providing the best compromise between the accuracy and robustness performances. Simulations were performed for direct-drive two-axis robot arm. The evolved FLC with the proposed design technique found to provide a very satisfactory performance under the wide range of operation conditions and to overcome problem associated with coupling and nonlinearities characteristics inherent to robot arms.
Abstract: The LHP is a two-phase device with extremely high
effective thermal conductivity that utilizes the thermodynamic
pressure difference to circulate a cooling fluid. A thermodynamics
analytical model is developed to explore different parameters effects
on a Loop Heat Pipe (LHP).. The effects of pipe length, pipe
diameter, condenser temperature, and heat load are reported. As pipe
length increases and/or pipe diameter decreases, a higher temperature
is expected in the evaporator.
Abstract: The hydrothermal behavior of a bed consisting of
magnetic and shale oil particle admixtures under the effect of a
transverse magnetic field is investigated. The phase diagram, bed
void fraction are studied under wide range of the operating
conditions i.e., gas velocity, magnetic field intensity and fraction of
the magnetic particles. It is found that the range of the stabilized
regime is reduced as the magnetic fraction decreases. In addition, the
bed voidage at the onset of fluidization decreases as the magnetic
fraction decreases. On the other hand, Nusselt number and
consequently the heat transfer coefficient is found to increase as the
magnetic fraction decreases. An empirical equation is investigated to
relate the effect of the gas velocity, magnetic field intensity and
fraction of the magnetic particles on the heat transfer behavior in the
bed.