Abstract: Sedimentation process resulting from soil erosion in
the water basin especially in arid and semi-arid where poor
vegetation cover in the slope of the mountains upstream could
contribute to sediment formation. The consequence of sedimentation
not only makes considerable change in the morphology of the river
and the hydraulic characteristics but would also have a major
challenge for the operation and maintenance of the canal network
which depend on water flow to meet the stakeholder-s requirements.
For this reason mathematical modeling can be used to simulate the
effective factors on scouring, sediment transport and their settling
along the waterways. This is particularly important behind the
reservoirs which enable the operators to estimate the useful life of
these hydraulic structures. The aim of this paper is to simulate the
sedimentation and erosion in the eastern and western water intake
structures of the Dez Diversion weir using GSTARS-3 software. This
is done to estimate the sedimentation and investigate the ways in
which to optimize the process and minimize the operational
problems. Results indicated that the at the furthest point upstream of
the diversion weir, the coarser sediment grains tended to settle. The
reason for this is the construction of the phantom bridge and the
outstanding rocks just upstream of the structure. The construction of
these along the river course has reduced the momentum energy
require to push the sediment loads and make it possible for them to
settle wherever the river regime allows it. Results further indicated a
trend for the sediment size in such a way that as the focus of study
shifts downstream the size of grains get smaller and vice versa. It
was also found that the finding of the GSTARS-3 had a close
proximity with the sets of the observed data. This suggests that the
software is a powerful analytical tool which can be applied in the
river engineering project with a minimum of costs and relatively
accurate results.
Abstract: In this paper, we carry over some of the results which
are valid on a certain class of Moufang-Klingenberg planes M(A)
coordinatized by an local alternative ring A := A(ε) = A+Aε of
dual numbers to finite projective Klingenberg plane M(A) obtained
by taking local ring Zq (where prime power q = pk) instead of A.
So, we show that the collineation group of M(A) acts transitively
on 4-gons, and that any 6-figure corresponds to only one inversible
m ∈ A.
Abstract: The distance between two objects is an important
problem in CAGD, CAD and CG etc. It will be presented in this paper
that a simple and quick method to estimate the distance between a
point and a Bezier curve on a Bezier surface.
Abstract: This project aims to investigate the potential of
torrefaction to improve the properties of Malaysian palm kernel shell
(PKS) as a solid fuel. A study towards torrefaction of PKS was
performed under various temperature and residence time of 240, 260,
and 280oC and 30, 60, and 90 minutes respectively. The torrefied
PKS was characterized in terms of the mass yield, energy yield,
elemental composition analysis, calorific value analysis, moisture and
volatile matter contents, and ash and fixed carbon contents. The mass
and energy yield changes in the torrefied PKS were observed to
prove that the temperature has more effect compare to residence time
in the torrefaction process. The C content of PKS increases while H
and O contents decrease after torrefaction, which resulted in higher
heating value between 5 to 16%. Meanwhile, torrefaction caused the
ash and fixed carbon content of PKS to increase, and the moisture
and volatile matter to decrease.
Abstract: We introduce an extended resource leveling model that abstracts real life projects that consider specific work ranges for each resource. Contrary to traditional resource leveling problems this model considers scarce resources and multiple objectives: the minimization of the project makespan and the leveling of each resource usage over time. We formulate this model as a multiobjective optimization problem and we propose a multiobjective genetic algorithm-based solver to optimize it. This solver consists in a two-stage process: a main stage where we obtain non-dominated solutions for all the objectives, and a postprocessing stage where we seek to specifically improve the resource leveling of these solutions. We propose an intelligent encoding for the solver that allows including domain specific knowledge in the solving mechanism. The chosen encoding proves to be effective to solve leveling problems with scarce resources and multiple objectives. The outcome of the proposed solvers represent optimized trade-offs (alternatives) that can be later evaluated by a decision maker, this multi-solution approach represents an advantage over the traditional single solution approach. We compare the proposed solver with state-of-art resource leveling methods and we report competitive and performing results.
Abstract: In this paper, we study on finite projective Hjelmslev planes M(Zq) coordinatized by Hjelmslev ring Zq (where prime power q = pk). We obtain finite hyperbolic Klingenberg planes from these planes under certain conditions. Also, we give a combinatorical result on M(Zq), related by deleting a line from lines in same neighbour.
Abstract: Value engineering is an efficacious contraption for
administrators to make up their minds. Value perusals proffer the
gaffers a suitable instrument to decrease the expenditures of the life
span, quality amelioration, structural improvement, curtailment of the
construction schedule, longevity prolongation or a merging of the
aforementioned cases. Subjecting organizers to pressures on one
hand and their accountability towards their pertinent fields together
with inherent risks and ambiguities of other options on the other hand
set some comptrollers in a dilemma utilization of risk management
and the value engineering in projects manipulation with regard to
complexities of implementing projects can be wielded as a
contraption to identify and efface each item which wreaks
unnecessary expenses and time squandering sans inflicting any
damages upon the essential project applications. Of course It should
be noted that implementation of risk management and value
engineering with regard to the betterment of efficiency and functions
may lead to the project implementation timing elongation. Here time
revamping does not refer to time diminishing in the whole cases. his
article deals with risk and value engineering conceptualizations at
first. The germane reverberations effectuated due to its execution in
Iran Khodro Corporation are regarded together with the joint features
and amalgamation of the aforesaid entia; hence the proposed
blueprint is submitted to be taken advantage of in engineering and
industrial projects including Iran Khodro Corporation.
Abstract: Customer-supplier collaboration enables firms to
achieve greater success than acting independently. Nevertheless, not
many firms have fully utilized the potential of collaboration. This
paper presents organizational and human related success factors for
collaboration in manufacturing supply chains in casting industry. Our
research approach was a case study including multiple cases. Data
was gathered by interviews and group discussions in two different
research projects. In the first research project we studied seven firms
and in the second five. It was found that the success factors are
interrelated, in other words, organizational and human factors
together enable success but not any of them alone. Some of the found
success factors are a culture of following agreements, and a speed of
informing the partner about changes affecting to the product or the
delivery chain.
Abstract: The past decade has seen enormous growth in the amount of software produced. However, given the ever increasing complexity of the software being developed and the concomitant rise in the typical project size, managers are becoming increasingly aware of the importance of issues that influence the productivity levels of the project teams involved. By analyzing the latest release of ISBSG data repository, we report on the factors found to significantly influence the productivity among which average team size and language type are the two most essential ones. Building on this we present an original model for evaluating the potential productivity during the project planning stage.
Abstract: In today-s economy plant engineering faces many
challenges. For instance the intensifying competition in this business
is leading to cost competition and needs for a shorter time-to-market.
To remain competitive companies need to make their businesses
more profitable by implementing improvement programs such as
standardization projects. But they have difficulties to tap their full
economic potential for various reasons. One of them is non-holistic
planning and implementation of standardization projects. This paper
describes a new conceptual framework - the layer-model. The model
combines and expands existing proven approaches in order to
improve design, implementation and management of standardization
projects. Based on a holistic approach it helps to systematically
analyze the effects of standardization projects on different business
layers and enables companies to better seize the opportunities offered
by standardization.
Abstract: Enterprise Architecture (EA) is a framework for description, coordination and alignment of all activities across the organization in order to achieve strategic goals using ICT enablers. A number of EA-compatible frameworks have been developed. We, in this paper, mainly focus on Federal Enterprise Architecture Framework (FEAF) since its reference models are plentiful. Among these models we are interested here in its business reference model (BRM). The test process is one important subject of an EA project which is to somewhat overlooked. This lack of attention may cause drawbacks or even failure of an enterprise architecture project. To address this issue we intend to use International Software Testing Qualification Board (ISTQB) framework and standard test suites to present a method to improve EA testing process. The main challenge is how to communicate between the concepts of EA and ISTQB. In this paper, we propose a method for integrating these concepts.
Abstract: In the past, there were many bridge-s collapses due to
lack of bridge structural capacity information. Most of concrete
bridge health was relied on information from visual inspection, which
sometime was inadequate. This study was conducted in order to
investigate relationship between bridge structural condition and
bridge visual condition. This study was a part of a big project
conducted at Department of Highways of Thailand. In this study, 31
bridges including slab-type bridges, plank-girder bridges, prestressed
box-beam bridges, prestressed I-girder bridges and prestressed multibeam
bridges were selected for visual inspection and load test. It was
found a positive correlation between bridge appearance and bridge-s
load carrying capacity. However, statistical characteristic revealed
low correlation between them.
Abstract: Today-s healthcare industries had become more
patient-centric than profession-centric, from which the issues of quality of healthcare and the patient safety are the major concerns in the modern healthcare facilities. An unplanned extubation (UE) may
be detrimental to the patient-s life, and thus is one of the major indexes
of patient safety and healthcare quality. A high UE rate not only
defeated the healthcare quality as well as the patient safety policy but
also the nurses- morality, and job satisfaction. The UE problem in a psychiatric hospital is unique and may be a tough challenge for the
healthcare professionals for the patients were mostly lacking communication capabilities. We reported with this essay a particular
project that was organized to reduce the UE rate from the current 2.3%
to a lower and satisfactory level in the long-term care units of a psychiatric hospital. The project was conducted between March 1st,
2011 and August 31st, 2011. Based on the error information gathered
from varied units of the hospital, the team analyzed the root causes
with possible solutions proposed to the meetings. Four solutions were
then concluded with consensus and launched to the units in question.
The UE rate was now reduced to a level of 0.17%. Experience from
this project, the procedure and the tools adopted would be good reference to other hospitals.
Abstract: The development of wearable sensing technologies is a great challenge which is being addressed by the Proetex FP6 project (www.proetex.org). Its main aim is the development of wearable sensors to improve the safety and efficiency of emergency personnel. This will be achieved by continuous, real-time monitoring of vital signs, posture, activity, and external hazards surrounding emergency workers. We report here the development of carbon dioxide (CO2) sensing boot by incorporating commercially available CO2 sensor with a wireless platform into the boot assembly. Carefully selected commercially available sensors have been tested. Some of the key characteristics of the selected sensors are high selectivity and sensitivity, robustness and the power demand. This paper discusses some of the results of CO2 sensor tests and sensor integration with wireless data transmission
Abstract: A registration framework for image-guided robotic
surgery is proposed for three emergency neurosurgical procedures,
namely Intracranial Pressure (ICP) Monitoring, External Ventricular
Drainage (EVD) and evacuation of a Chronic Subdural Haematoma
(CSDH). The registration paradigm uses CT and white light as
modalities. This paper presents two simulation studies for a
preliminary evaluation of the registration protocol: (1) The loci of the
Target Registration Error (TRE) in the patient-s axial, coronal and
sagittal views were simulated based on a Fiducial Localisation Error
(FLE) of 5 mm and (2) Simulation of the actual framework using
projected views from a surface rendered CT model to represent white
light images of the patient. Craniofacial features were employed as
the registration basis to map the CT space onto the simulated
intraoperative space. Photogrammetry experiments on an artificial
skull were also performed to benchmark the results obtained from the
second simulation. The results of both simulations show that the
proposed protocol can provide a 5mm accuracy for these
neurosurgical procedures.
Abstract: This paper introduces the effective speckle reduction of
synthetic aperture radar (SAR) images using inner product spaces in
undecimated wavelet domain. There are two major areas in projection
onto span algorithm where improvement can be made. First is the use
of undecimated wavelet transformation instead of discrete wavelet
transformation. And second area is the use of smoothing filter namely
directional smoothing filter which is an additional step. Proposed
method does not need any noise estimation and thresholding
technique. More over proposed method gives good results on both
single polarimetric and fully polarimetric SAR images.
Abstract: The growing outsourcing of logistics services
resulting from the ongoing current in firms of costs
reduction/increased efficiency means that it is becoming more and
more important for the companies doing the outsourcing to carry out
a proper evaluation.
The multiple definitions and measures of logistics service
performance found in research on the topic create a certain degree of
confusion and do not clear the way towards the proper measurement
of their performance. Do a model and a specific set of indicators exist
that can be considered appropriate for measuring the performance of
logistics services outsourcing in industrial environments? Are said
indicators in keeping with the objectives pursued by outsourcing? We
aim to answer these and other research questions in the study we have
initiated in the field within the framework of the international High
Performance Manufacturing (HPM) project of which this paper
forms part.
As the first stage of this research, this paper reviews articles
dealing with the topic published in the last 15 years with the aim of
detecting the models most used to make this measurement and
determining which performance indicators are proposed as part of
said models and which are most used. The first steps are also taken in
determining whether these indicators, financial and operational, cover
the aims that are being pursued when outsourcing logistics services.
The findings show there is a wide variety of both models and
indicators used. This would seem to testify to the need to continue
with our research in order to try to propose a model and a set of
indicators for measuring the performance of logistics services
outsourcing in industrial environments.
Abstract: Within the last years, several technologies have been developed to help building e-learning portals. Most of them follow approaches that deliver a vast amount of functionalities, suitable for class-like learning. The SuGI project, as part of the D-Grid (funded by the BMBF), targets on delivering a highly scalable and sustainable learning solution to provide materials (e.g. learning modules, training systems, webcasts, tutorials, etc.) containing knowledge about Grid computing to the D-Grid community. In this article, the process of the development of an e-learning portal focused on the requirements of this special user group is described. Furthermore, it deals with the conceptual and technical design of an e-learning portal, addressing the special needs of heterogeneous target groups. The main focus lies on the quality management of the software development process, Web templates for uploading new contents, the rich search and filter functionalities which will be described from a conceptual as well as a technical point of view. Specifically, it points out best practices as well as concepts to provide a sustainable solution to a relatively unknown and highly heterogeneous community.
Abstract: Buildings are one of the valuable assets to provide
people with shelters for work, leisure and rest. After years of
attacks by weather, buildings will deteriorate which need proper
maintenance in order to fulfill the requirements and satisfaction of
the users. Poorly managed buildings not just give a negative image
to the city itself, but also pose potential risk hazards to the health
and safety of the general public. As a result, the management of
maintenance projects has played an important role in cities like
Hong Kong where the problem of urban decay has drawn much
attention. However, most research has focused on managing new
construction, and little research effort has been put on maintenance
projects. Given the short duration and more diversified nature of
work, repair and maintenance works are found to be more difficult
to monitor and regulate when compared with new works. Project
participants may face with problems in running maintenance
projects which should be investigated so that proper strategies can
be established. This paper aims to provide a thorough analysis on
the problems of running maintenance projects. A review of
literature on the characteristics of building maintenance projects
was firstly conducted, which forms a solid basis for the empirical
study. Results on the problems and difficulties of running
maintenance projects from the viewpoints of industry practitioners
will also be delivered with a view to formulating effective
strategies for managing maintenance projects successfully.
Abstract: In this project cadmium ions were adsorbed from
aqueous solutions onto either date pits; a cheap agricultural and nontoxic
material, or chemically activated carbon prepared from date pits
using phosphoric acid. A series of experiments were conducted in a
batch adsorption technique to assess the feasibility of using the
prepared adsorbents. The effects of the process variables such as
initial cadmium ions concentration, contact time, solution pH and
adsorbent dose on the adsorption capacity of both adsorbents were
studied. The experimental data were tested using different isotherm
models such as Langmuir, Freundlich, Tempkin and Dubinin-
Radushkevich. The results showed that although the equilibrium data
could be described by all models used, Langmuir model gave slightly
better results when using activated carbon while Freundlich model,
gave better results with date pits.