Abstract: Flood routing is used in estimating the travel time and attenuation of flood waves as they move downstream a river or channel. The routing procedure is usually classified as hydrologic or hydraulic. Hydraulic methods utilize the equations of continuity and motion. Kinematic routing, a hydraulic technique was used in routing Asa River at Ilorin. The river is of agricultural and industrial importance to Ilorin, the capital of Kwara State, Nigeria. This paper determines the kinematic parameters of kinematic wave velocity, time step, time required to traverse, weighting factor and change in length. Values obtained were 4.67 m/s, 19 secs, 21 secs, 0.75 and 100 m, respectively. These parameters adequately reflect the watershed and flow characteristics essential for the routing. The synthetic unit hydrograph was developed using the Natural Resources Conservation Service (NRCS) method. 24-hr 10yr, 25yr, 50yr and 100yr storm hydrographs were developed from the unit hydrograph using convolution procedures and the outflow hydrographs were obtained for each of 24-hr 10yr, 25yr, 50yr and 100yr indicating 0.11 m3/s, 0.10 m3/s, 0.10 m3/s and 0.10 m3/s attenuations respectively.
Abstract: This paper proposes a method to automatic transformation of CIM level to PIM level respecting the MDA approach. Our proposal is based on creating a good CIM level through well-defined rules allowing as achieving rich models that contain relevant information to facilitate the task of the transformation to the PIM level. We define, thereafter, an appropriate PIM level through various UML diagram. Next, we propose set rules to move from CIM to PIM. Our method follows the MDA approach by considering the business dimension in the CIM level through the use BPMN, standard modeling business of OMG, and the use of UML in PIM advocated by MDA in this level.
Abstract: Ion exchange is one of the methods used to remove heavy metal such as copper and cobalt from wastewaters. Parameters affecting the ion-exchange of copper and cobalt aqueous solutions using clinoptilolite are the objectives of this study. Synthetic solutions were prepared with the concentration of 0.02M, 0.06M and 0.1M. The cobalt solution was maintained to 0.02M while varying the copper solution to the above stated concentrations. The clinoptilolite was activated with HCl and H2SO4 for removal efficiency. The pHs of the solutions were found to be acidic hence enhancing the copper and cobalt removal. The natural clinoptilolite performance was also found to be lower compared to the HCl and H2SO4 activated one for the copper removal ranging from 68% to 78% of Cu2+ uptake with the natural clinoptilolite to 66% to 51% with HCl and H2SO4 respectively. It was found that the activated clinoptilolite removed more copper and cobalt than the natural one and found that the electronegativity of the metal plays a role in the metal removal and the clinoptilolite selectivity.
Abstract: Assistive robotics are playing a vital role in advancing the quality of life for disable people. There exist wide range of systems that can control and guide autonomous mobile robots. The objective of the control system is to guide an autonomous mobile robot using the movement of eyes by means of EOG signal. The EOG signal is acquired using Ag/AgCl electrodes and this signal is processed by a microcontroller unit to calculate the eye gaze direction. Then according to the guidance control strategy, the control commands of the wheelchair are sent. The classification of different eye movements allows us to generate simple code for controlling the wheelchair. This work was aimed towards developing a usable and low-cost assistive robotic wheel chair system for disabled people. To live more independent life, the system can be used by the handicapped people especially those with only eye-motor coordination.
Abstract: Chaotic analysis has been performed on the river flow time series before and after applying the wavelet based de-noising techniques in order to investigate the noise content effects on chaotic nature of flow series. In this study, 38 years of monthly runoff data of three gauging stations were used. Gauging stations were located in Ghar-e-Aghaj river basin, Fars province, Iran. Noise level of time series was estimated with the aid of Gaussian kernel algorithm. This step was found to be crucial in preventing removal of the vital data such as memory, correlation and trend from the time series in addition to the noise during de-noising process.
Abstract: Advances in the field of image processing envision a
new era of evaluation techniques and application of procedures in
various different fields. One such field being considered is the
biomedical field for prognosis as well as diagnosis of diseases. This
plethora of methods though provides a wide range of options to select
from, it also proves confusion in selecting the apt process and also in
finding which one is more suitable. Our objective is to use a series of
techniques on bone scans, so as to detect the occurrence of
rheumatoid arthritis (RA) as accurately as possible. Amongst other
techniques existing in the field our proposed system tends to be more
effective as it depends on new methodologies that have been proved
to be better and more consistent than others. Computer aided
diagnosis will provide more accurate and infallible rate of
consistency that will help to improve the efficiency of the system.
The image first undergoes histogram smoothing and specification,
morphing operation, boundary detection by edge following algorithm
and finally image subtraction to determine the presence of
rheumatoid arthritis in a more efficient and effective way. Using preprocessing
noises are removed from images and using segmentation,
region of interest is found and Histogram smoothing is applied for a
specific portion of the images. Gray level co-occurrence matrix
(GLCM) features like Mean, Median, Energy, Correlation, Bone
Mineral Density (BMD) and etc. After finding all the features it
stores in the database. This dataset is trained with inflamed and noninflamed
values and with the help of neural network all the new
images are checked properly for their status and Rough set is
implemented for further reduction.
Abstract: This research aims to study the level of democratic political culture and the factors that affect the democratic political culture of 5th and 6th graders under the authority of Dusit District Office, Bangkok by using stratified sampling for probability sampling and using purposive sampling for non-probability sampling to collect data toward the distribution of questionnaires to 300 respondents. This covers all of the schools under the authority of Dusit District Office. The researcher analyzed the data by using descriptive statistics which include arithmetic mean, standard deviation, and inferential statistics which are Independent Samples T-test (T-test) and One-Way ANOVA (F-test). The researcher also collected data by interviewing the target groups, and then analyzed the data by the use of descriptive analysis. The result shows that 5th and 6th graders under the authority of Dusit District Office, Bangkok have exposed to democratic political culture at high level in overall. When considering each part, it found out that the part that has highest mean is “the constitutional democratic governmental system is suitable for Thailand” statement. The part with the lowest mean is “corruption (cheat and defraud) is normal in Thai society” statement. The factor that affects democratic political culture is grade levels, occupations of mothers, and attention in news and political movements.
Abstract: In this paper, a backward semi-Lagrangian scheme
combined with the second-order backward difference formula
is designed to calculate the numerical solutions of nonlinear
advection-diffusion equations. The primary aims of this paper are
to remove any iteration process and to get an efficient algorithm
with the convergence order of accuracy 2 in time. In order to achieve
these objects, we use the second-order central finite difference and the
B-spline approximations of degree 2 and 3 in order to approximate
the diffusion term and the spatial discretization, respectively. For the
temporal discretization, the second order backward difference formula
is applied. To calculate the numerical solution of the starting point
of the characteristic curves, we use the error correction methodology
developed by the authors recently. The proposed algorithm turns out
to be completely iteration free, which resolves the main weakness
of the conventional backward semi-Lagrangian method. Also, the
adaptability of the proposed method is indicated by numerical
simulations for Burgers’ equations. Throughout these numerical
simulations, it is shown that the numerical results is in good
agreement with the analytic solution and the present scheme offer
better accuracy in comparison with other existing numerical schemes.
Abstract: The sound pressure level (SPL) of the moving-coil
loudspeaker (MCL) is often simulated and analyzed using the lumped
parameter model. However, the SPL of a MCL cannot be simulated
precisely in the high frequency region, because the value of cone
effective area is changed due to the geometry variation in different
mode shapes, it is also related to affect the acoustic radiation mass and
resistance. Herein, the paper presents the inverse method which has a
high ability to measure the value of cone effective area in various
frequency points, also can estimate the MCL electroacoustic
parameters simultaneously. The proposed inverse method comprises
the direct problem, adjoint problem, and sensitivity problem in
collaboration with nonlinear conjugate gradient method. Estimated
values from the inverse method are validated experimentally which
compared with the measured SPL curve result. Results presented in
this paper not only improve the accuracy of lumped parameter model
but also provide the valuable information on loudspeaker cone design.
Abstract: As an emerging business model, cloud computing has been initiated to satisfy the need of organizations and to push Information Technology as a utility. The shift to the cloud has changed the way Information Technology departments are managed traditionally and has raised many concerns for both, public and private sectors.
The purpose of this study is to investigate the possibility of cloud computing services replacing services provided traditionally by IT departments. Therefore, it aims to 1) explore whether organizations in Oman are ready to move to the cloud; 2) identify the deciding factors leading to the adoption or rejection of cloud computing services in Oman; and 3) provide two case studies, one for a successful Cloud provider and another for a successful adopter.
This paper is based on multiple research methods including conducting a set of interviews with cloud service providers and current cloud users in Oman; and collecting data using questionnaires from experts in the field and potential users of cloud services.
Despite the limitation of bandwidth capacity and Internet coverage offered in Oman that create a challenge in adopting the cloud, it was found that many information technology professionals are encouraged to move to the cloud while few are resistant to change.
The recent launch of a new Omani cloud service provider and the entrance of other international cloud service providers in the Omani market make this research extremely valuable as it aims to provide real-life experience as well as two case studies on the successful provision of cloud services and the successful adoption of these services.
Abstract: Intrabody communication (IBC) is a new way of transferring data using human body as a medium. Minute current can travel though human body without any harm. IBC can remove electrical wires for human area network. IBC can be also a secure communication network system unlike wireless networks which can be accessed by anyone with bad intentions. One of the IBC systems is based on frequency shift keying modulation where individual data are transmitted to the external devices for the purpose of secure access such as digital door lock. It was found that the quality of IBC data transmission was heavily dependent on ground configurations of electronic circuits. Reliable IBC transmissions were not possible when both of the transmitter and receiver used batteries as circuit power source. Transmission was reliable when power supplies were used as power source for both transmitting and receiving sites because the common ground was established through the grounds of instruments such as power supply and oscilloscope. This was due to transmission dipole size and the ground effects of floor and AC power line. If one site used battery as power source and the other site used the AC power as circuit power source, transmission was possible.
Abstract: Termites have been observed as major pre-colonisation and post-colonisation pest insect of honeybees’ wooden hives in Nigeria. However, pest situation studies in modern beekeeping have been largely directed towards those pests that affect honeybees rather than the biological structure (wood) which houses the honeybees and the influence of seasons on the pests’ activities against the hives. This study, therefore, investigated the influence of seasons on the intensity of hives attacks by termites for 2 years in University of Port Harcourt, Rivers State using visual inspection. The Experimental Apiary was established with 15 Kenyan’s top bar hives made of Triplochiton scleroxylon wood that were strategically placed and observed within the Department of Forestry and Wildlife Management arboretum. The colonies hives consistently showed comparatively lower termite’s infestation levels in the dry season and, consequently, also lower attacks on the colonized hives. The result indicated raining season as a distinct period for more destructive activities of termites on the hives and strongly associated with dryness of the hives. Since previous study and observations have linked colonization with dry season coupled with minimal attacked on colonized hives; the non-colonised hives should be removed from the field at the onset of raining season and returned two weeks prior to dry season to reduce hives degradation by pests.
Abstract: The aim of this research is to design and implement line-tracking mobile robot. The robot must follow a line drawn on the floor with different color, avoids hitting moving object like another moving robot or walking people and achieves color sensing. The control system reacts by controlling each of the motors to keep the tracking sensor over the middle of the line. Proximity sensors used to avoid hitting moving objects that may pass in front of the robot. The programs have been written using micro c instructions, then converted into PIC16F887 ATmega48/88/168 microcontrollers counterparts. Practical simulations show that the walking robot accurately achieves line following action and exactly recognizes the colors and avoids any obstacle in front of it.
Abstract: Various biomass based resources, which can be used
as an extender, or a complete substitute of diesel fuel may have very
significant role in the development of agriculture, industrial and
transport sectors in the energy crisis. Use of Karanja oil methyl ester
biodiesel in a CI DI engine was found highly compatible with engine
performance along with lower exhaust emission as compared to
diesel fuel but with slightly higher NOx emission and low wear
characteristics. The combustion related properties of vegetable oils
are somewhat similar to diesel oil. Neat vegetable oils or their blends
with diesel, however, pose various long-term problems in
compression ignition engines. These undesirable features of
vegetable oils are because of their inherent properties like high
viscosity, low volatility, and polyunsaturated character. Pongamia
methyl ester (PME) was prepared by transesterification process using
methanol for long term engine operations. The physical and
combustion-related properties of the fuels thus developed were found
to be closer to that of the diesel. A neat biodiesel (PME) was selected
as a fuel for the tribological study of biofuels.
Two similar new engines were completely disassembled and
subjected to dimensioning of various vital moving parts and then
subjected to long-term endurance tests on neat biodiesel and diesel
respectively. After completion of the test, both the engines were
again disassembled for physical inspection and wear measurement of
various vital parts. The lubricating oil samples drawn from both
engines were subjected to atomic absorption spectroscopy (AAS) for
measurement of various wear metal traces present. The additional
lubricating property of biodiesel fuel due to higher viscosity as
compared to diesel fuel resulted in lower wear of moving parts and
thus improved the engine durability with a bio-diesel fuel. Results
reported from AAS tests confirmed substantially lower wear and thus
improved life for biodiesel operated engines.
Abstract: Background. Food-related allergies and intolerances are frequently occurring in dogs. Diagnosis and monitoring according ‘Golden Standard’ of elimination efficiency is, however, time consuming, expensive, and requires expert clinical setting. In order to facilitate rapid and robust, quantitative testing of intolerance, and determining the individual offending foods, a serological test is implicated for Alimentary Induced Diseases and manifestations. Method. As we developed Medisynx IgG Human Screening Test ELISA before and the dog’ immune system is most similar to humans, we were able to develop Medisynx IgG Dog Screening Test ELISA as well. In this randomized, double-blind, split-sample, retro perspective study 47 dogs suffering from Canine Atopic Dermatitis (CAD) and several secondary induced reactions were included to participate in serological Medisynx IgG Dog Screening Test ELISA (within < 0,02 % SD). Results were expressed as titers relative to the standard OD readings to diagnose alimentary induced diseases and monitoring efficacy of an individual eliminating diet in dogs. Split sample analysis was performed by independently sending 2 times 3 ml serum under two unique codes. Results. The veterinarian monitored these dogs to check dog’ results at least at 3, 7, 21, 49, 70 days and after period of 6 and 12 months on an individual negative diet and a positive challenge (retrospectively) at 6 months. Data of each dog were recorded in a screening form and reported that a complete recovery of all clinical manifestations was observed at or less than 70 days (between 50 and 70 days) in the majority of dogs (44 out of 47 dogs =93.6%). Conclusion. Challenge results showed a significant result of 100% in specificity as well as 100% positive predicted value. On the other hand, sensitivity was 95,7% and negative predictive value was 95,7%. In conclusion, an individual diet based on IgG ELISA in dogs provides a significant improvement of atopic dermatitis and pruritus including all other non-specific defined allergic skin reactions as erythema, itching, biting and gnawing at toes, as well as to several secondary manifestations like chronic diarrhoea, chronic constipation, otitis media, obesity, laziness or inactive behaviour, pain and muscular stiffness causing a movement disorders, excessive lacrimation, hyper behaviour, nervous behaviour and not possible to stay alone at home, anxiety, biting and aggressive behaviour and disobedience behaviour. Furthermore, we conclude that a relatively more severe systemic candidiasis, as shown by relatively higher titer (class 3 and 4 IgG reactions to Candida albicans), influence the duration of recovery from clinical manifestations in affected dogs. These findings are consistent with our preliminary human clinical studies.
Abstract: This research presents the design, fabrication and application of a flavor sensor for an integrated electronic tongue and electronic nose that can allow rapid characterization of multi-component mixtures in a solution. The odor gas and liquid are separated using hydrophobic porous membrane in micro fluidic channel. The sensor uses an array composed of microbeads in micromachined cavities localized on silicon wafer. Sensing occurs via colorimetric and fluorescence changes to receptors and indicator molecules that are attached to termination sites on the polymeric microbeads. As a result, the sensor array system enables simultaneous and near-real-time analyses using small samples and reagent volumes with the capacity to incorporate significant redundancies. One of the key parts of the system is a passive pump driven only by capillary force. The hydrophilic surface of the fluidic structure draws the sample into the sensor array without any moving mechanical parts. Since there is no moving mechanical component in the structure, the size of the fluidic structure can be compact and the fabrication becomes simple when compared to the device including active microfluidic components. These factors should make the proposed system inexpensive to mass-produce, portable and compatible with biomedical applications.
Abstract: To measure or asses any government’s efficiency we need to measure the performance of this government in regards to the quality of the service it provides. Using a technological platform in service provision became a trend and a public demand. It is also a public need to make sure these services are aligned to values and to the whole government’s strategy, vision and goals as well. Providing services using technology tools and channels can enhance the internal business process and also help establish many essential values to government services like transparency and excellence, since in order to establish e-services many standards and policies must be put in place to enable the handing over of decision making to a mature system oriented mechanism. There was no doubt that the Sultanate of Oman wanted to enhance its services and move it towards automation and establishes a smart government as well as links its services to life events. Measuring government efficiency is very essential in achieving social security and economic growth, since it can provide a clear dashboard of all projects and improvements. Based on this data we can improve the strategies and align the country goals to them.
Abstract: Gypsum is being applied to ameliorate subsoil acidity and to overcome the problem of very slow lime movement from surface lime applications. Reduced Crude Conversion Spent Lime (RCCSL) containing anhydrite was evaluated for use as a liming material with specific consideration given to the movement of sulfate into the acid subsoil. Agricultural lime and RCCSL were applied at 0, 0.5, 1.0, and 1.5 times the lime requirement of 6.72 Mg ha-1 to an acid Trappist silt loam (TypicHapuldult). Corn [Zea mays (L.)]was grown following lime material application and soybean [Glycine max (L.) Merr.]was grown in the second year.Soil pH increased rapidly with the addition of the RCCSL material. Over time there was no difference in soil pH between the materials but there was with increasing rate. None of the observed changes in plant nutrient concentration had an impact on yield. Grain yield was higher for the RCCSL amended treatments in the first year but not in the second. There was a significant increase in soybean grain yield from the full lime requirement treatments over no lime.
Abstract: This paper provides an analysis of the insurance cycle in the Republic of Croatia and whether they are affected by catastrophic losses on a global level. In general, it is considered that insurance cycles are particularly pronounced in periods of financial crisis, but are also affected by the growing number of catastrophic losses. They cause the change of insurance cycle and premium growth and intensification and narrowing of the coverage conditions, so these variables move in the same direction and these phenomena point to a new cycle. The main goal of this paper is to determine the existence of insurance cycle in the Republic of Croatia and investigate whether catastrophic losses have an influence on insurance cycles.
Abstract: This numerical study aims to develop a coupled,
passive and active control strategy of the flow around a cylinder of
diameter D, and Re=4000. The strategy consists to put a cylindrical
rod in front of a deforming cylinder. The quasi- elliptical deformation
of cylinder follow a sinusoidal law in order to reduce the drag force.
To analyze the evolution of unsteady vortices, the Large Eddy
Simulation approach is used in this 2D simulation, carried out using
ANSYS – Fluent. The movement of deformation is reproduced using
an internal subroutine, introduced in the form of a User Defined
Function UDF. Two diameters of the rod were tested for a rod placed
at a distance L = 3 ×d, with an amplitudes of deformation A = 5%, A
= 25% and A = 50% of the cylinder diameter, the frequency of
deformation take the values fd = 1fn, 5fn and 8fn, which fn
represents the naturel vortex shedding frequency. The results show
substantial changes in the flow behavior and for a rod of 6mm (1%
D) with amplitude A = 25%, and with a 2fn frequency, drag
reduction of 60% was recorded.