Abstract: High strength concrete (HSC) provides high strength
but lower ductility than normal strength concrete. This low ductility
limits the benefit of using HSC in building safe structures. On the
other hand, when designing reinforced concrete beams, designers
have to limit the amount of tensile reinforcement to prevent the
brittle failure of concrete. Therefore the full potential of the use of
steel reinforcement can not be achieved. This paper presents the idea
of confining concrete in the compression zone so that the HSC will
be in a state of triaxial compression, which leads to improvements in
strength and ductility. Five beams made of HSC were cast and tested.
The cross section of the beams was 200×300 mm, with a length of 4
m and a clear span of 3.6 m subjected to four-point loading, with
emphasis placed on the midspan deflection. The first beam served as
a reference beam. The remaining beams had different tensile
reinforcement and the confinement shapes were changed to gauge
their effectiveness in improving the strength and ductility of the
beams. The compressive strength of the concrete was 85 MPa and the
tensile strength of the steel was 500 MPa and for the stirrups and
helixes was 250 MPa. Results of testing the five beams proved that
placing helixes with different diameters as a variable parameter in the
compression zone of reinforced concrete beams improve their
strength and ductility.
Abstract: Different variants for buoyancy-affected terms in k-ε turbulence model have been utilized to predict the flow parameters more accurately, and investigate applicability of alternative k-ε turbulence buoyant closures in numerical simulation of a horizontal gravity current. The additional non-isotropic turbulent stress due to buoyancy has been considered in production term, based on Algebraic Stress Model (ASM). In order to account for turbulent scalar fluxes, general gradient diffusion hypothesis has been used along with Boussinesq gradient diffusion hypothesis with a variable turbulent Schmidt number and additional empirical constant c3ε.To simulate buoyant flow domain a 2D vertical numerical model (WISE, Width Integrated Stratified Environments), based on Reynolds- Averaged Navier-Stokes (RANS) equations, has been deployed and the model has been further developed for different k-ε turbulence closures. Results are compared against measured laboratory values of a saline gravity current to explore the efficient turbulence model.
Abstract: In this paper, the fuzzy linear programming formulation
of fuzzy maximal flow problems are proposed and on the basis of the
proposed formulation a method is proposed to find the fuzzy optimal
solution of fuzzy maximal flow problems. In the proposed method all
the parameters are represented by triangular fuzzy numbers. By using
the proposed method the fuzzy optimal solution of fuzzy maximal
flow problems can be easily obtained. To illustrate the proposed
method a numerical example is solved and the obtained results are
discussed.
Abstract: In this paper, a robust statistics based filter to remove salt and pepper noise in digital images is presented. The function of the algorithm is to detect the corrupted pixels first since the impulse noise only affect certain pixels in the image and the remaining pixels are uncorrupted. The corrupted pixels are replaced by an estimated value using the proposed robust statistics based filter. The proposed method perform well in removing low to medium density impulse noise with detail preservation upto a noise density of 70% compared to standard median filter, weighted median filter, recursive weighted median filter, progressive switching median filter, signal dependent rank ordered mean filter, adaptive median filter and recently proposed decision based algorithm. The visual and quantitative results show the proposed algorithm outperforms in restoring the original image with superior preservation of edges and better suppression of impulse noise
Abstract: Milk from differently fed cows (supplemented with carotenoids from carrots or palm oil product Carotino CAF 100) was obtained in a conventional dairy farm to assess the carotenoid potential to protect milk fat against oxidation. The extracted anhydrous milk fat (AMF) was tested by peroxide value, and Rancimat tests. Temperature, and light stimulation for reaction acceleration was used. The oxidative stability enhancement by carotenoids was detected in peroxide value test – the strongest effect was observed in palm oil, following by carrot supplemented group, compared to control group, whose feed was unchanged. Rancimat accelerated oxidation test results did not show any superiority of the oxidative stability of the AMF samples from milk of the carotenoidsupplemented cow groups. The average oxidation stability of AMF dark-stored samples was 12.59 ± 0.294 h, and it was significantly (p < 0.05) higher than that of AMF light-affected samples, i.e. 2.60 ± 0.191 h.
Abstract: Custom power is a technology driven product and
service solution which embraces a family devices such as Dynamic
Voltage Restorer (DVR), Distributed Shunt Compensator
(DSTATCOM), Solid State Breaker (SSB) etc which will provide
power quality functions at distribution voltages. The rapid response
of these devices enables them to operate in real time, providing
continuous and dynamic control of the supply including voltage and
reactive power regulation, harmonic reduction and elimination of
voltage dips. This paper presents the benefits of multilevel inverters
when they are used for DPC based custom power devices. Power
flow control mechanism, salient features, advantages and
disadvantages of direct power control (DPC) using lookup table,
SVM, predictive voltage vector and hybrid DPC strategies are
discussed in this paper. Simulation results of three level inverter
based STATCOM, harmonic analysis of multi level inverters are
presented at the end.
Abstract: The cardiovascular system has become the most
important subject of clinical research, particularly measurement of
arterial blood flow. Therefore correct determination of arterial
diameter is crucial. We propose a novel, semi-automatic method for
artery lumen detection. The method is based on Gaussian probability
function. Usability of our proposed method was assessed by
analyzing ultrasound B-mode CFA video sequences acquired from
eleven healthy volunteers. The correlation coefficient between the
manual and semi-automatic measurement of arterial diameter was
0.996. Our proposed method for detecting artery boundary is novel
and accurate enough for the measurement of artery diameter.
Abstract: A lot of research made during these last 15 years
showed that the quantification of the springback has a significant role
in the industry of sheet metal forming. These studies were made with
the objective of finding techniques and methods to minimize or
completely avoid this permanent physical variation. Moreover, the
use of steel and aluminum alloys in the car industry and aviation
poses every day the problem of the springback. The determination in
advance of the quantity of the springback allows consequently the
design and manufacture of the tool. The aim of this paper is to study
experimentally the influence of the blank holder force BHF and the
radius of curvature of the die on the springback and their influence on
the strain in various zone of specimen.
The original of our purpose consist on tests which are ensured by
adapting a U-type stretching-bending device on a tensile testing
machine, where we studied and quantified the variation of the
springback according to displacement.
Abstract: The ubiquitous payment problems within construction
industry of China are notoriously hard to be resolved, thus lead to a
series of impacts to the industry chain. Among of them, the most direct
result is affecting the normal operation of contractors negatively. A
wealth of research has already discussed reasons of the payment
problems by introducing a number of possible improvement strategies.
But the causalities of these problems are still far from harsh reality. In
this paper, the authors propose a model for cash flow system of
construction projects by introducing System Dynamics techniques to
explore causal facets of the payment problem. The effects of payment
arrears on both cash flow and profitability of project are simulated into
four scenarios by using data from real projects. Simulating results
show visible clues to help contractors quantitatively determining the
consequences for the construction project that arise from payment
delay.
Abstract: Field experiment was conducted to investigate the combine use of animal manure and inorganic fertilizer on growth and yield performance of vegetable cowpea. The experiment was laid out in a Randomized Complete Block Design (RCBD) with seven treatments. Poultry manure, cattle manure and goat manure were evaluated with recommended level of inorganic fertilizer for vegetable cowpea. The highest crop yield was obtained by the application of poultry manure combined with the recommended level of inorganic fertilizer. The lowest yield was obtained by the application of goat manure only. In addition, the results revealed that the goat manure and cattle manure were inferior to poultry manure as a source of organic manure for vegetable cowpea cultivation. The animal manure combine with chemical fertilizer gave a higher yield when compared to the sole application of animal manure. The soil analysis showed that the nitrogen content and phosphorus content of poultry manure treated plots were higher than other treatments tested. But potassium content was higher in goat manure treated plots. The results further revealed that the poultry manure has a beneficial effect on crop growth and yield compared with other treatments. Therefore, the combined use of poultry manure with inorganic fertilizer application has been recognized as the most suitable way of ensuring high crop yield.
Abstract: Self-sensing estimates the air gap within an electro
magnetic path by analyzing the bearing coil current and/or voltage
waveform. The self-sensing concept presented in this paper has been
developed within the research project “Active Magnetic Bearings
with Supreme Reliability" and is used for position sensor fault
detection.
Within this new concept gap calculation is carried out by an alldigital
analysis of the digitized coil current and voltage waveform.
For analysis those time periods within the PWM period are used,
which give the best results. Additionally, the concept allows the
digital compensation of nonlinearities, for example magnetic
saturation, without degrading signal quality. This increases the
accuracy and robustness of the air gap estimation and additionally
reduces phase delays.
Beneath an overview about the developed concept first
measurement results are presented which show the potential of this
all-digital self-sensing concept.
Abstract: This paper develops a critical perspective on using
culture and creativity as tools for urban regeneration. Following a
brief assessment of the evolution of cultural policy in recent decades
and different urban regeneration scheme, the concepts of creativity
and creative cities are discussed. This is followed by an attempt to
clarify the relationship between the concepts of creativity and culture.
A more detailed critique of cultural and creative initiatives in Serbian
cities is then undertaken. These attempts show that the potential for
development of urban regeneration driven by culture and creativity
exist. But, these initiatives failed to produce adequate results because
they did not take root as a comprehensive urban regeneration
strategy, therefore, recommendations for further development are
offered.
Abstract: Complex statistical analysis of stresses in concrete
slab of the real type of rigid pavement is performed. The
computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method
that respects the structural nonlinearity, enables to model different arrangement of joints, and the entire model can be loaded by the
thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with help of special
contact elements. Four concrete slabs separated by transverse and
longitudinal joints and the additional subgrade layers and soil to the depth of about 3m are modeled. The thickness of individual layers,
physical and mechanical properties of materials, characteristics of
joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique
Updated Latin Hypercube Sampling with 20 simulations is used for statistical analysis. As results, the estimates of basic statistics of the
principal stresses s1 and s3 in 53 points on the upper and lower surface of the slabs are obtained.
Abstract: Realistic 3D face model is desired in various
applications such as face recognition, games, avatars, animations, and
etc. Construction of 3D face model is composed of 1) building a face
shape model and 2) rendering the face shape model. Thus, building a
realistic 3D face shape model is an essential step for realistic 3D face
model. Recently, 3D morphable model is successfully introduced to
deal with the various human face shapes. 3D dense correspondence
problem should be precedently resolved for constructing a realistic 3D
dense morphable face shape model. Several approaches to 3D dense
correspondence problem in 3D face modeling have been proposed
previously, and among them optical flow based algorithms and TPS
(Thin Plate Spline) based algorithms are representative. Optical flow
based algorithms require texture information of faces, which is
sensitive to variation of illumination. In TPS based algorithms
proposed so far, TPS process is performed on the 2D projection
representation in cylindrical coordinates of the 3D face data, not
directly on the 3D face data and thus errors due to distortion in data
during 2D TPS process may be inevitable.
In this paper, we propose a new 3D dense correspondence algorithm
for 3D dense morphable face shape modeling. The proposed algorithm
does not need texture information and applies TPS directly on 3D face
data. Through construction procedures, it is observed that the proposed
algorithm constructs realistic 3D face morphable model reliably and
fast.
Abstract: The adoption of building information modeling (BIM)
is increasing in the construction industry. However, quantity
surveyors are slow in adoption compared to other professions due to
lack of awareness of the BIM’s potential in their profession. It is still
unclear on how BIM application can enhance quantity surveyors’
work performance and project performance. The aim of this research
is to identify the capabilities of BIM in quantity surveying practices
and examine the relationship between BIM capabilities and project
performance. Questionnaire survey and interviews were adopted for
data collection. Literature reviews identified there are eleven BIM
capabilities in quantity surveying practice. Questionnaire results
showed that there are several BIM capabilities significantly
correlated with project performance in time, cost and quality aspects
and the results were validated through interviews. These findings
show that BIM has the capabilities to enhance quantity surveyors’
performances and subsequently improved project performance.
Abstract: A multi-block algorithm and its implementation in two-dimensional finite element numerical model CCHE2D are presented. In addition to a conventional Lagrangian Interpolation Method (LIM), a novel interpolation method, called Consistent Interpolation Method (CIM), is proposed for more accurate information transfer across the interfaces. The consistent interpolation solves the governing equations over the auxiliary elements constructed around the interpolation nodes using the same numerical scheme used for the internal computational nodes. With the CIM, the momentum conservation can be maintained as well as the mass conservation. An imbalance correction scheme is used to enforce the conservation laws (mass and momentum) across the interfaces. Comparisons of the LIM and the CIM are made using several flow simulation examples. It is shown that the proposed CIM is physically more accurate and produces satisfactory results efficiently.
Abstract: We report here structural, mechanical and I-V
characteristics of Zn1-xMxO ceramic samples with various x and M.
It is found that the considered dopants does not influence the wellknown
peaks related to wurtzite structure of ZnO ceramics, while the
shape and size of grains are clearly affected. Average crystalline
diameters, deduced from XRD are between 42 nm and 54 nm, which
are 70 times lower than those obtained from SEM micrographs.
Interestingly, the potential barrier could be formed by adding Cu up
to 0.20, and it is completely deformed by 0.025 Ni additions. The
breakdown field could be enhanced up to 4138 V/cm by 0.025 Cu
additions, followed by a decrease with further increase of Cu . On
the other hand a gradual decrease in VHN is reported for both
dopants and their values are higher in Ni samples as compared to Cu
samples. The electrical conductivity is generally improved by Ni,
while addition of Cu improved it only in the over doped region (≥
0.10). These results are discussed in terms of the difference of
valency and ferromagnetic ordering for both dopants as compared to
undoped sample.
Abstract: A finite element analysis was conducted to determine
the effect of moisture diffusion and hygroscopic swelling in rice. A
parallel simple stochastic modeling was performed to predict the
number of grains cracked as a result of moisture absorption and
hygroscopic swelling. Rice grains were soaked in thermally (25 oC)
controlled water and then tested for compressive stress. The
destructive compressive stress tests revealed through compressive
stress calculation that the peak force required to cause cracking in
grains soaked in water reduced with time as soaking duration was
extended. Results of the experiment showed that several grains had
their value of the predicted compressive stress below the von Mises
stress and were interpreted as grains which become cracked and/or
broke during soaking. The technique developed in this experiment
will facilitate the approximation of the number of grains which will
crack during soaking.
Abstract: Pepper spray use has gained momentum since 1992
and although the active ingredient is readily available, it is considered
a weapon with restricted use in many regions, including The
Bahamas. In light of controversy in the literature regarding the
severity of presenting respiration complaints among individuals postacute
exposure of pepper spray inhalation, this descriptive case series
study was conducted to assess the respiratory status of persons
evaluated during a mass casualty in The Bahamas. Parameters noted
were patients- demographics and respiration severity determined via
clinical examination findings, disposition and follow-up review of the
20 persons. Their most common complaint was difficulty breathing
post exposure. Two required admission and stayed for
Abstract: This research analyzes factors affecting the success of
Litecoin Value within Thailand and develops a guideline for selfreliance
for effective business implementation. Samples in this study
included 119 people through surveys. The results revealed four main
factors affecting the success as follows: 1) Future Career training
should be pursued in applied Litecoin development. 2) Didn't grasp
the concept of a digital currency or see the benefit of a digital
currency. 3) There is a great need to educate the next generation of
learners on the benefits of Litecoin within the community. 4) A great
majority didn't know what Litecoin was.
The guideline for self-reliance planning consisted of 4 aspects: 1)
Development planning: by arranging meet up groups to conduct
further education on Litecoin and share solutions on adoption into
every day usage. Local communities need to develop awareness of
the usefulness of Litecoin and share the value of Litecoin among
friends and family. 2) Computer Science and Business Management
staff should develop skills to expand on the benefits of Litecoin
within their departments. 3) Further research should be pursued on
how Litecoin Value can improve business and tourism within
Thailand. 4) Local communities should focus on developing Litecoin
awareness by encouraging street vendors to accept Litecoin as
another form of payment for services rendered.