Abstract: Reducing sloshing is one of the major challenges in industries where transporting of liquid is involved. The present study investigates the sloshing effect for different liquid levels of 50% of the tank capacity. CFD simulation for two different baffle configurations has been carried out using a time-based multiphase Volume of fluid (VOF) scheme. Baffles were introduced to examine the sloshing effect inside the tank. Results were compared against the baseline case to assess the effectiveness of baffles; maximum liquid height over the period of the simulation was considered as the parameter for measuring the sloshing effect inside the tank. It was found that the addition of baffles reduced the sloshing effect inside the tank as compared to the baseline model.
Abstract: In this modern era of automation, most of the academic
exams and competitive exams are Multiple Choice Questions (MCQ).
The responses of these MCQ based exams are recorded in the
Optical Mark Reader (OMR) sheet. Evaluation of the OMR sheet
requires separate specialized machines for scanning and marking.
The sheets used by these machines are special and costs more than a
normal sheet. Available process is non-economical and dependent on
paper thickness, scanning quality, paper orientation, special hardware
and customized software. This study tries to tackle the problem of
evaluating the OMR sheet without any special hardware and making
the whole process economical. We propose an image processing
based algorithm which can be used to read and evaluate the scanned
OMR sheets with no special hardware required. It will eliminate the
use of special OMR sheet. Responses recorded in normal sheet is
enough for evaluation. The proposed system takes care of color,
brightness, rotation, little imperfections in the OMR sheet images.
Abstract: This paper presents parameter estimation of a
single-phase rectifier using extended Kalman filter (EKF). The state
space model has been obtained using Kirchhoff’s current law (KCL)
and Kirchhoff’s voltage law (KVL). The capacitor voltage and diode
current of the circuit have been estimated using EKF. Simulation
results validate the better accuracy of the proposed method as
compared to the least mean square method (LMS). Further, EKF
has the advantage that it can be used for nonlinear systems.
Abstract: India is known as a country of diversity regarding the social, cultural and wide geographical variations. In the north and north-west part of the country, the strong patriarchal norms and the male dominance based social structure are the important constructs. Patriarchal social setup adversely affects the women’s social and economic wellbeing and hence in that social structure women are considered as second level citizen. Work participation rate of women has directly linked to the development of society or household. Haryana is one of the developed states of India, still being ahead in economic prosperity, much lagged behind in gender-based equality and male dominance in all dimensions of life. The position of women in the Haryana is no better than the other states of India. Haryana state has the great difference among the male-female sex ratio which is a serious concern for social science research as a demographic problem for the state. Now women are requiring for their holistic empowerment and that will take care of them for an enabling process that must lead to their economic as well as social transformation. Hence, the objective of the paper is to address the role of sex ratio, women literacy and her work participation in the process of their empowerment with special attention to the gender perspective. The study used the data from Census of India from 1991 to 2011. This paper will examine the regional disparity of sex ratio, literacy rate and female work participation and the improvement of empowerment of women in the state of Haryana. This paper will suggest the idea for focusing much intensively on the issues of women empowerment through enhancement of her education, workforce participation and social participation with people participation and holistic approach.
Abstract: Inherited complexity is one of the difficult tasks in software engineering field. Further, it is said that there is no physical laws or standard guidelines suit for designing different types of software. Hence, to make the software engineering as a matured engineering discipline like others, it is necessary that it has its own theoretical frameworks and laws. Software designing and development is a human effort which takes a lot of time and considers various parameters for successful completion of the software. The cognitive informatics plays an important role for understanding the essential characteristics of the software. The aim of this work is to consider the fundamental characteristics of the source code of Object-Oriented software i.e. complexity and understandability. The complexity of the programs is analyzed with the help of extracted important attributes of the source code, which is further utilized to evaluate the understandability factor. The aforementioned characteristics are analyzed on the basis of 16 C++ programs by distributing them to forty MCA students. They all tried to understand the source code of the given program and mean time is taken as the actual time needed to understand the program. For validation of this work, Briand’s framework is used and the presented metric is also evaluated comparatively with existing metric which proves its robustness.
Abstract: Chromite ores are primarily used for extraction of chromium, which is an expensive metal. For low grade chromite ores (containing less than 40% Cr2O3), the chromium extraction is not usually economically viable. India possesses huge quantities of low grade chromite reserves. This deposit can be utilized after proper physical beneficiation. Magnetic separation techniques may be useful after reduction for the beneficiation of low grade chromite ore. The sample collected from the sukinda mines is characterized by XRD which shows predominant phases like maghemite, chromite, silica, magnesia and alumina. The raw ore is crushed and ground to below 75 micrometer size. The microstructure of the ore shows that the chromite grains surrounded by a silicate matrix and porosity observed the exposed side of the chromite ore. However, this ore may be utilized in refractory applications. Chromite ores contain Cr2O3, FeO, Al2O3 and other oxides like Fe-Cr, Mg-Cr have a high tendency to form spinel compounds, which usually show high refractoriness. Initially, the low grade chromite ore (containing 34.8% Cr2O3) was reduced at 1200 0C for 80 minutes with 30% coke fines by weight, before being subjected to magnetic separation. The reduction by coke leads to conversion of higher state of iron oxides converted to lower state of iron oxides. The pre-reduced samples are then characterized by XRD. The magnetically inert mass was then reacted with 20% MgO by weight at 1450 0C for 2 hours. The resultant product was then tested for various refractoriness parameters like apparent porosity, slag resistance etc. The results were satisfactory, indicating that the resultant spinel compounds are suitable for refractory applications for elevated temperature processes.
Abstract: The demand for Urban transportation is characterised by a large scale temporal and spatial variations which causes heavy congestion inside metro trains in peak hours near Centre Business District (CBD) of the city. The conventional approach to address peak hour congestion, metro trains has been to increase the supply by way of introduction of more trains, increasing the length of the trains, optimising the time table to increase the capacity of the system. However, there is a limitation of supply side measures determined by the design capacity of the systems beyond which any addition in the capacity requires huge capital investments. The demand side interventions are essentially required to actually spread the demand across the time and space. In this study, an attempt has been made to identify the potential Transport Demand Management tools applicable to Urban Rail Transportation systems with a special focus on differential pricing. A conceptual price elasticity model has been developed to analyse the effect of various combinations of peak and nonpeak hoursfares on demands. The elasticity values for peak hour, nonpeak hour and cross elasticity have been assumed from the relevant literature available in the field. The conceptual price elasticity model so developed is based on assumptions which need to be validated with actual values of elasticities for different segments of passengers. Once validated, the model can be used to determine the peak and nonpeak hour fares with an objective to increase overall ridership, revenue, demand levelling and optimal utilisation of assets.
Abstract: Thermal stratification has drawn much attention because of the malfunctions at various nuclear plants in U.S.A that raised significant safety concerns. The concerns due to this phenomenon relate to thermal stresses in branch pipes connected to the reactor coolant system piping. This stress limits the lifetime of the piping system, and even leading to penetrating cracks. To assess origin of valve damage in the pipeline, it is essential to determine the effect of turbulence penetration on valve leakage; since stratified flow is generally generated by turbulent penetration or valve leakage. As a result, we concluded with the help of coupled fluent-structural analysis that the pipe with less turbulence has less chance of failure there by requiring less maintenance.
Abstract: Renewable energy resources, which can supplement space and water heating for residential buildings, can have a noticeable impact on natural gas consumption and air pollution. This study considers a technical analysis of a combined solar water heating system with evacuated tube solar collectors for different solar coverage, ranging from 20% to 100% of the total roof area of a typical residential building located in Edmonton, Alberta, Canada. The alternative heating systems were conventional (non-condensing) and condensing tankless water heaters and condensing boilers that were coupled to solar water heating systems. The performance of the alternative heating systems was compared to a traditional heating system, consisting of a conventional boiler, applied to houses of various gross floor areas. A comparison among the annual natural gas consumption, carbon dioxide (CO2) mitigation, and emissions for the various house sizes indicated that the combined solar heating system can reduce the natural gas consumption and CO2 emissions, and increase CO2 mitigation for all the systems that were studied. The results suggest that solar water heating systems are potentially beneficial for residential heating system applications in terms of energy savings and CO2 mitigation.
Abstract: The main perspective of the present study aims at overcoming solubility problems by using the technique of solid dispersion. Repaglinide is a BCS Class II drug, having low aqueous solubility and therefore, low bioavailability. Solid dispersions of repaglinide with different carriers Polyvinyl Pyrrolidone (PVP) and Ethyl Cellulose (EC) in different ratios were prepared by suspending method and Dissolving methods. In vitro release studies revealed that the F7 formulation showed extended drug release. So, the dissolution profile of solid dispersion containing EC and PVP K30 (1: 3) was selected as the best formulation because of its extended drug release among all formulations. In conclusion, solid dispersions of Repaglinide in PVP have shown to be a promising approach to improve the bioavailability of Repaglinide.
Abstract: This paper is focused on the analysis and comparison of liquidity ratios and asset liability management practices in top three banks from public, private and foreign sector in India. The analysis is based upon the liquidity ratios calculation and the determination of maturity gap profiles for the banks under study. The paper also compares these banks maturity gap profiles with their corresponding group’s maturity gap profiles. This paper identifies the interest rate sensitivity of the balance sheet items of these banks to determine the gap between rate sensitive assets and rate sensitive liabilities. The results of this study suggest that overall banks in India have very good short term liquidity position and all banks are financing their short term liabilities by their long term assets.
Abstract: The aim of present work was to optimize the effect of Ethyl Cellulose (EC) and Polyvinyl Pyrrolidone (PVP) concentration in extended release solid dispersion of Glibenclamide using combination of hydrophilic and hydrophobic polymers such as Polyvinyl Pyrrolidone and Ethyl cellulose. The advantage of solid dispersion technique provides a unique approach to particle size reduction and increased rates of dissolution. The compatibility studies of the drug and polymers were studied by TLC and results suggested no interaction between drug and polymers. Solid dispersions of Glibenclamide were prepared by common solvent evaporation method using Polyvinyl Pyrrolidone and Ethyl cellulose. The results indicated that homogeneous or heterogeneous conditions during the preparation methods employed governed the internal structures of the polymer matrices while retaining the drug in an amorphous form. F2 formulation prepared by solid dispersion method, displayed extended drug release followed by Higuchi matrix model indicating diffusion release of GLB from polymer matrices.
Abstract: An effective supplier selection process is very important to the success of any manufacturing organization. The main objective of supplier selection process is to reduce purchase risk, maximize overall value to the purchaser, and develop closeness and long-term relationships between buyers and suppliers in today’s competitive industrial scenario. The literature on supplier selection criteria and methods is full of various analytical and heuristic approaches. Some researchers have developed hybrid models by combining more than one type of selection methods. It is felt that supplier selection criteria and method is still a critical issue for the manufacturing industries therefore in the present paper the literature has been thoroughly reviewed and critically analyzed to address the issue.
Abstract: Ranking of fuzzy numbers play an important role in
decision making, optimization, forecasting etc. Fuzzy numbers must
be ranked before an action is taken by a decision maker. In this
paper, with the help of several counter examples it is proved that
ranking method proposed by Chen and Chen (Expert Systems with
Applications 36 (2009) 6833-6842) is incorrect. The main aim of this
paper is to propose a new approach for the ranking of generalized
trapezoidal fuzzy numbers. The main advantage of the proposed
approach is that the proposed approach provide the correct ordering
of generalized and normal trapezoidal fuzzy numbers and also the
proposed approach is very simple and easy to apply in the real life
problems. It is shown that proposed ranking function satisfies all
the reasonable properties of fuzzy quantities proposed by Wang and
Kerre (Fuzzy Sets and Systems 118 (2001) 375-385).
Abstract: In this paper, a new method is proposed to find the fuzzy optimal solution of fuzzy assignment problems by representing all the parameters as triangular fuzzy numbers. The advantages of the pro-posed method are also discussed. To illustrate the proposed method a fuzzy assignment problem is solved by using the proposed method and the obtained results are discussed. The proposed method is easy to understand and to apply for finding the fuzzy optimal solution of fuzzy assignment problems occurring in real life situations.
Abstract: The notion of intuitionistic fuzzy sets was introduced
by Atanassov as a generalization of the notion of fuzzy sets. Y.B. Jun
and S.Z. Song introduced the notion of intuitionistic fuzzy points.
In this paper we find some relations between the intuitionistic fuzzy
ideals of a semigroup S and the set of all intuitionistic fuzzy points
of S.
Abstract: End milling process is one of the common metal
cutting operations used for machining parts in manufacturing
industry. It is usually performed at the final stage in manufacturing a
product and surface roughness of the produced job plays an
important role. In general, the surface roughness affects wear
resistance, ductility, tensile, fatigue strength, etc., for machined parts
and cannot be neglected in design. In the present work an
experimental investigation of end milling of aluminium alloy with
carbide tool is carried out and the effect of different cutting
parameters on the response are studied with three-dimensional
surface plots. An artificial neural network (ANN) is used to establish
the relationship between the surface roughness and the input cutting
parameters (i.e., spindle speed, feed, and depth of cut). The Matlab
ANN toolbox works on feed forward back propagation algorithm is
used for modeling purpose. 3-12-1 network structure having
minimum average prediction error found as best network architecture
for predicting surface roughness value. The network predicts surface
roughness for unseen data and found that the result/prediction is
better. For desired surface finish of the component to be produced
there are many different combination of cutting parameters are
available. The optimum cutting parameter for obtaining desired
surface finish, to maximize tool life is predicted. The methodology is
demonstrated, number of problems are solved and algorithm is coded
in Matlab®.
Abstract: In this paper the concept of Q-fuzzification of ideals of Γ-semigroups has been introduced and some important properties have been investigated. A characterization of regular Γ-semigroup in terms of Q-fuzzy ideals has been obtained. Operator semigroups of a Γ-semigroup has been made to work by obtaining various relationships between Q-fuzzy ideals of a Γ-semigroup and that of its operator semigroups.
Abstract: In this paper, the fuzzy linear programming formulation
of fuzzy maximal flow problems are proposed and on the basis of the
proposed formulation a method is proposed to find the fuzzy optimal
solution of fuzzy maximal flow problems. In the proposed method all
the parameters are represented by triangular fuzzy numbers. By using
the proposed method the fuzzy optimal solution of fuzzy maximal
flow problems can be easily obtained. To illustrate the proposed
method a numerical example is solved and the obtained results are
discussed.