Abstract: In this paper, an ultra low power and low jitter 12bit
CMOS digitally controlled oscillator (DCO) design is presented.
Based on a ring oscillator implemented with low power Schmitt
trigger based inverters. Simulation of the proposed DCO using 32nm
CMOS Predictive Transistor Model (PTM) achieves controllable
frequency range of 550MHz~830MHz with a wide linearity and high
resolution. Monte Carlo simulation demonstrates that the time-period
jitter due to random power supply fluctuation is under 31ps and the
power consumption is 0.5677mW at 750MHz with 1.2V power
supply and 0.53-ps resolution. The proposed DCO has a good
robustness to voltage and temperature variations and better linearity
comparing to the conventional design.
Abstract: The results obtained after incorporating the competence “creativity" to the subject Technical Drawing of the first course of the Degree in Forestry, Technical University of Madrid, are presented in this study.At first, learning activities which could serve two functions at the same time -developing students- creativity and developing other specific competences of the subject- were considered. Besides, changes in the assessment procedure were made and a method which analyzes two aspects of the assessment of the competence creativity was established. On the one hand, the products are evaluated by analyzing the outcomes obtained by students in the essays suggested and by establishing a parameter to assess the creativity expressed in those essays. On the other, an assessment of the student is directly carried out through a psychometric test which has been previously chosen by the team.Moreover, these results can be applied to similar or could be of general application.
Abstract: Industrial surveys shows that manufacturing
companies define the qualities of thermal removing process based on
the dimension and physical appearance of the cutting material
surface. Therefore, the roughness of the surface area of the material
cut by the plasma arc cutting process and the rate of the removed
material by the manual plasma arc cutting machine was importantly
considered. Plasma arc cutter Selco Genesis 90 was used to cut
Standard AISI 1017 Steel of 200 mm x100 mm x 6 mm manually
based on the selected parameters setting. The material removal rate
(MRR) was measured by determining the weight of the specimens
before and after the cutting process. The surface roughness (SR)
analysis was conducted using Mitutoyo CS-3100 to determine the
average roughness value (Ra). Taguchi method was utilized to
achieve optimum condition for both outputs studied. The
microstructure analysis in the region of the cutting surface is
performed using SEM. The results reveal that the SR values are
inversely proportional to the MRR values. The quality of the surface
roughness depends on the dross peak that occurred after the cutting
process.
Abstract: Sensors have been used in various kinds of academic
fields and applications. In this article, we propose the idea of
modularized sensors that combine multiple sensor modules into a
unique sensor. We divide a sensor into several units according to
functionalities. Each unit has different sensor modules, which share
the same type of connectors and can be serially and arbitrarily
connected each other. A user can combine different sensor modules
into a sensor platform according to requirements. Compared with
current modularized sensors, the proposed sensor platform is highly
flexible and reusable. We have implemented the prototype of the
proposed sensor platform, and the experimental results show the
proposed platform can work correctly.
Abstract: In this paper, a new dependable algorithm based on an adaptation of the standard variational iteration method (VIM) is used for analyzing the transition from steady convection to chaos for lowto-intermediate Rayleigh numbers convection in porous media. The solution trajectories show the transition from steady convection to chaos that occurs at a slightly subcritical value of Rayleigh number, the critical value being associated with the loss of linear stability of the steady convection solution. The VIM is treated as an algorithm in a sequence of intervals for finding accurate approximate solutions to the considered model and other dynamical systems. We shall call this technique as the piecewise VIM. Numerical comparisons between the piecewise VIM and the classical fourth-order Runge–Kutta (RK4) numerical solutions reveal that the proposed technique is a promising tool for the nonlinear chaotic and nonchaotic systems.
Abstract: Cassava is one of the top five crops in Cameroon. Its
evolution has remained constant since the independence period and
the production has more than tripled. It is a crop with multiple
industrial capacities but the sector-s business opportunities are
underexploited. Using Strengths, Weaknesses, Opportunities and
Threats analysis method, this paper examines the cassava actual state.
It appraises the sector-s strengths (S), considers suitable measures to
strengthen weaknesses (W), evaluates strategies to fully benefit from
the sector numerous business opportunities (O) and explore means to
convert threats (T) into opportunities. Data were collected from the
ministry of agriculture and rural development and different actors.
The results show that cassava sector embodies many business
opportunities and stands as a raw material provider for many
industries but ultimately requires challenges to be tackled
appropriately.
Abstract: In determining the electromagnetic properties of
magnetic materials, hysteresis modeling is of high importance. Many
models are available to investigate those characteristics but they tend
to be complex and difficult to implement. In this paper a new
qualitative hysteresis model for ferromagnetic core is presented,
based on the function approximation capabilities of adaptive neuro
fuzzy inference system (ANFIS). The proposed ANFIS model
combined the neural network adaptive capabilities and the fuzzy
logic qualitative approach can restored the hysteresis curve with a
little RMS error. The model accuracy is good and can be easily
adapted to the requirements of the application by extending or
reducing the network training set and thus the required amount of
measurement data.
Abstract: From the beginning of creation, human being has ever
fought against the ecosystem by changes has made in environment.
The most environmental changes on the nature have been done after
starting the concentrated life in the same region. Dams are one of the
most important buildings in water resources and transferring. These
buildings have been made from old times without access to
hydrological, hydraulically, hydro mechanical information. Dams
have positive and negative effects on environment. Constructing a
dam relatively causes equal ecological consequences. According to
different criteria, environmental effects of dams can lead short term
and long term damages. These effects may influence on the situation
and treatment of meteorology, biology, culture, ancient works, etc
and severely causes to change and complicate it. So considering
importance of positive effects of dam construction, it is necessary to
minimize negative environmental effects of dams to achieve a stable
development. In this article the considered effects and their solutions
in influencing on assessment of destructive environmental effects of
dams construction have been surveyed and presented.
Abstract: This paper addresses linear quadratic regulation (LQR)
for variable speed variable pitch wind turbines. Because of the
inherent nonlinearity of wind turbine, a set of operating conditions is
identified and then a LQR controller is designed for each operating
point. The feedback controller gains are then interpolated linearly to
get control law for the entire operating region. Besides, the
aerodynamic torque and effective wind speed are estimated online to
get the gain-scheduling variable for implementing the controller. The
potential of the method is verified through simulation with the help of
MATLAB/Simulink and GH Bladed. The performance and
mechanical load when using LQR are also compared with that when
using PI controller.
Abstract: Multi criteria decision analysis (MDCA) covers both
data and experience. It is very common to solve the problems with
many parameters and uncertainties. GIS supported solutions improve
and speed up the decision process. Weighted grading as a MDCA
method is employed for solving the geotechnical problems. In this
study, geotechnical parameters namely soil type; SPT (N) blow
number, shear wave velocity (Vs) and depth of underground water
level (DUWL) have been engaged in MDCA and GIS. In terms of
geotechnical aspects, the settlement suitability of the municipal area
was analyzed by the method. MDCA results were compatible with
the geotechnical observations and experience. The method can be
employed in geotechnical oriented microzoning studies if the criteria
are well evaluated.
Abstract: Environmental contamination is a common problem in ex-industrial and industrial sites. This article gives a brief description of general applied environmental investigation methodologies and possible remediation applications in Latvia. Most of contaminated areas are situated in former and active industrial, military areas and ports. Industrial and logistic activities very often have been with great impact for more than hundred years thus the contamination level with heavy metals, hydrocarbons, pesticides, persistent organic pollutants is high and is threatening health and environment in general. 242 territories now are numbered as contaminated and fixed in the National Register of contaminated territories in Latvia. Research and remediation of contamination in densely populated areas are of important environmental policy domain. Four different investigation case studies of contaminated areas are given describing the history of use, environmental quality assessment as well as planned environmental management actions. All four case study locations are situated in Riga - the capital of the Republic of Latvia. The aim of this paper is to analyze the situation and problems with management of contaminated areas in Latvia, give description of field research methods and recommendations for remediation industry based on scientific data and innovations.
Abstract: The paper presents the design of a mini-UAV attitude
controller using the backstepping method. Starting from the nonlinear
dynamic equations of the mini-UAV, by using the backstepping
method, the author of this paper obtained the expressions of the
elevator, rudder and aileron deflections, which stabilize the UAV, at
each moment, to the desired values of the attitude angles. The attitude
controller controls the attitude angles, the angular rates, the angular
accelerations and other variables that describe the UAV longitudinal
and lateral motions. To design the nonlinear controller, by using the
backstepping technique, the nonlinear equations and the Lyapunov
analysis have been directly used. The designed controller has been
implemented in Matlab/Simulink environment and its effectiveness
has been tested with a campaign of numerical simulations using data
from the UAV flight tests. The obtained results are very good and
they are better than the ones found in previous works.
Abstract: EcoDam is an adenine-N6 DNA methyltransferase
that methylates the GATC sites in the Escherichia coli genome.
DNA-adenine methylation is not present in higher eukaryotes
including humans. These observations raise the possibility that dam
inhibitors may be used as anti-microbial agents. Polyphosphate
(Poly(P)) is an important metabolite and signaling molecule in
prokaryotes and eukaryotes. Here, by using gel retardation
experiments to investigate the competition of DNA binding by
EcoDam in the presence of polyphosphate, we found that Poly (P)
strongly interferes with DNA binding by EcoDam, while same
concentration of monophosphate does not. In addition, we
demonstrated that Poly (P) binding inhibits the activity of EcoDam
and our results suggest that Poly (P) led to strong inhibition of the
EcoDam catalytic activity, while monophosphate had only moderate
effect.
Abstract: This paper invites to dialogue and reflections on
innovation and entrepreneurship by presenting concepts of innovation
leading to the introduction of a complex theoretical framework;
Cooperative Innovation (CO-IN). CO-IN is a didactic model
enhancing and scaffolding processes of cooperation creating
innovation drawing on a Scandinavian tradition.
CO-IN is based on a cross-sectorial and multidisciplinary
approach. We introduce the concept of complementarity to help
capture the validity of diversity and we suggest the concept of “the
space in between" to understand the creation of identity as a
collective mind. We see dialogue and the use of multi modal
techniques as essential tools for conceptualizations giving possibility
for clarification of the complexity and diversity leading to decision
making based on knowledge as commons.
We introduce the didactic design and present our empirical
findings from an innovation workshop in Argentina. In a final
paragraph we reflect on the design as a support of the development of
common ground, collective mind and collective action and the
creation of knowledge as commons to facilitate innovation and
entrepreneurship.
Abstract: The overriding goal of software engineering is to
provide a high quality system, application or a product. To achieve
this goal, software engineers must apply effective methods coupled
with modern tools within the context of a mature software process
[2]. In addition, it is also must to assure that high quality is realized.
Although many quality measures can be collected at the project
levels, the important measures are errors and defects. Deriving a
quality measure for reusable components has proven to be
challenging task now a days. The results obtained from the study are
based on the empirical evidence of reuse practices, as emerged from
the analysis of industrial projects. Both large and small companies,
working in a variety of business domains, and using object-oriented
and procedural development approaches contributed towards this
study. This paper proposes a quality metric that provides benefit at
both project and process level, namely defect removal efficiency
(DRE).
Abstract: Conventional industrial monitoring systems are
tedious, inefficient and the at times integrity of the data is
unreliable. The objective of this system is to monitor industrial
processes specifically the fluid level which will measure the
instantaneous fluid level parameter and respond by text
messaging the exact value of the parameter to the user when
being enquired by a privileged access user. The development of
the embedded program code and the circuit for fluid level
measuring are discussed as well. Suggestions for future
implementations and efficient remote monitoring works are
included.
Abstract: The main objective of this study was to demonstrate that differentiation of infected and vaccinated animals (DIVA) strategy using different ELISA tests is possible when a subunit vaccine (Haemagglutinin protein) is used to prevent Avian influenza. Special emphasis was placed on the differentiation in the serological response to different components of the AIV (Nucleoprotein, Neuraminidase, Haemagglutinin, Nucleocapsid) between chickens that were vaccinated with a whole virus kill vaccine and recombinant vaccine. Furthermore, the potential use of this DIVA strategy using ELISA assays to detect Neuraminidase 1 (N1) was analyzed as strategy in countries where the field virus is H5N1 and the vaccine used is formulated with H5N2. Detection of AIV-s antibodies to any component in serum was negative for all animals on the study days 0-13. At study day 14 the titers of antibodies against Nucleoprotein (NP) and Nucleocapsid (NC) rose in the experimental groups vaccinated with Volvac® AI KV and were negatives during all the trial in the experimental groups vaccinated with a subunit H5; significant statistically differences were observed between these groups (p < 0.05). The seroconversion either Haemagglutinin or Neuraminidase was evident after 21 days post-vaccination in the experimental groups vaccinated with the respective viral fraction. Regarding the main aim of this study and according with the results that were obtained, use a combination of different ELISA test as a DIVA strategy is feasible when the vaccination is carry out with a subunit H5 vaccine. Also is possible to use the ELISA kit to detect Neuraminidase (either N1 or N2) as a DIVA concept in countries where H5N1 is present and the vaccination programs are done with H5N2 vaccine.
Abstract: High pressure adsorption of carbon dioxide on zeolite
13X was investigated in the pressure range (0 to 4) Mpa and
temperatures 298, 308 and 323K. The data fitting is accomplished
with the Toth, UNILAN, Dubinin-Astakhov and virial adsorption
models which are generally used for micro porous adsorbents such as
zeolites. Comparison with experimental data from the literature
indicated that the virial model would best determine results. These
results may be partly attributed to the flexibility of the virial model
which can accommodate as many constants as the data warrants.
Abstract: Any decision-making is based on certain theory. Taking
the public rental housing in Chongqing municipality as an example,
this essay states that the stakeholder theory can provide innovative
criteria and evaluation methods for Public Private Partnership (PPP)
projects. It gives an analysis of how to choose decision-making criteria
for different stakeholders in the PPP model and what measures to take
to meet the criteria to form “symbiotic" decision-making mode
through contracts and to boost the application of PPP model in
large-scale public programs in China.
Abstract: One of the most important parts of a cement factory is
the cement rotary kiln which plays a key role in quality and quantity of produced cement. In this part, the physical exertion and bilateral
movement of air and materials, together with chemical reactions take
place. Thus, this system has immensely complex and nonlinear dynamic equations. These equations have not worked out yet. Only
in exceptional case; however, a large number of the involved parameter were crossed out and an approximation model was
presented instead. This issue caused many problems for designing a
cement rotary kiln controller. In this paper, we presented nonlinear predictor and simulator models for a real cement rotary kiln by using
nonlinear identification technique on the Locally Linear Neuro-
Fuzzy (LLNF) model. For the first time, a simulator model as well as
a predictor one with a precise fifteen minute prediction horizon for a
cement rotary kiln is presented. These models are trained by
LOLIMOT algorithm which is an incremental tree-structure
algorithm. At the end, the characteristics of these models are expressed. Furthermore, we presented the pros and cons of these
models. The data collected from White Saveh Cement Company is used for modeling.