Abstract: Eating a meal is among the Activities of Daily Living,
but it takes a lot of time and effort for people with physical
or functional limitations. Dedicated technologies are cumbersome
and not portable, while general-purpose assistive robots such as
wheelchair-based manipulators are too hard to control for elaborate
continuous motion like eating. Eating with such devices has not
previously been automated, since there existed no description of
a feeding motion for uncontrolled environments. In this paper, we
introduce a feeding mode for assistive manipulators, including a
mathematical description of trajectories for motions that are difficult
to perform manually such as gathering and scooping food at a
defined/desired pace. We implement these trajectories in a sequence
of movements for a semi-automated feeding mode which can be
controlled with a very simple 3-button interface, allowing the user
to have control over the feeding pace. Finally, we demonstrate the
feeding mode with a JACO robotic arm and compare the eating
speed, measured in bites per minute of three eating methods: a
healthy person eating unaided, a person with upper limb limitations
or disability using JACO with manual control, and a person with
limitations using JACO with the feeding mode. We found that the
feeding mode allows eating about 5 bites per minute, which should
be sufficient to eat a meal under 30min.
Abstract: In impedance spectroscopy (IS) the response of a photo-active device is analysed as a function of ac bias. It is widely applied in a broad class of material systems and devices. It gives access to fundamental mechanisms of operation of solar cells. We have implemented a method of IS where we modulate the light instead of the bias. This scheme allows us to analyze not only carrier dynamics but also impedance of device locally. Here, using this scheme, we have measured the frequency-dependent photocurrent response of the thin-film planar and nano-textured Si solar cells using this method. Photocurrent response is measured in range of 50 Hz to 50 kHz. Bode and Nyquist plots are used to determine characteristic lifetime of both the cells. Interestingly, the carrier lifetime of both planar and nano-textured solar cells depend on back and front contact positions. This is due to either heterogeneity of device or contacts are not optimized. The estimated average lifetime is found to be shorter for the nano-textured cell, which could be due to the influence of the textured interface on the carrier relaxation dynamics.
Abstract: Accurate determination of wind turbine performance is necessary for economic operation of a wind farm. At present, the procedure to carry out the power performance verification of wind turbines is based on a standard of the International Electrotechnical Commission (IEC). In this paper, nonparametric statistical inference is applied to designing a simple, inexpensive method of verifying the power performance of a wind turbine. A statistical test is explained, examined, and the adequacy is tested over real data. The methods use the information that is collected by the SCADA system (Supervisory Control and Data Acquisition) from the sensors embedded in the wind turbines in order to carry out the power performance verification of a wind farm. The study has used data on the monthly output of wind farm in the Republic of Macedonia, and the time measuring interval was from January 1, 2016, to December 31, 2016. At the end, it is concluded whether the power performance of a wind turbine differed significantly from what would be expected. The results of the implementation of the proposed methods showed that the power performance of the specific wind farm under assessment was acceptable.
Abstract: Mining industry is known for its appetite to spend sizeable capital on mine equipment. However, in the current scenario, the mining industry is challenged by daunting factors of non-uniform geological conditions, uneven ore grade, uncontrollable and volatile mineral commodity prices and the ever increasing quest to optimize the capital and operational costs. Thus, the role of equipment reliability and maintenance planning inherits a significant role in augmenting the equipment availability for the operation and in turn boosting the mine productivity. This paper presents the Risk Based Maintenance (RBM) planning conducted on mine loading equipment namely Load Haul Dumpers (LHDs) at Vedanta Resources Ltd subsidiary Hindustan Zinc Limited operated Sindesar Khurd Mines, an underground zinc and lead mine situated in Dariba, Rajasthan, India. The mining equipment at the location is maintained by the Original Equipment Manufacturers (OEMs) namely Sandvik and Atlas Copco, who carry out the maintenance and inspection operations for the equipment. Based on the downtime data extracted for the equipment fleet over the period of 6 months spanning from 1st January 2017 until 30th June 2017, it was revealed that significant contribution of three downtime issues related to namely Engine, Hydraulics, and Transmission to be common among all the loading equipment fleet and substantiated by Pareto Analysis. Further scrutiny through Bubble Matrix Analysis of the given factors revealed the major influence of selective factors namely Overheating, No Load Taken (NTL) issues, Gear Changing issues and Hose Puncture and leakage issues. Utilizing the equipment wise analysis of all the downtime factors obtained, spares consumed, and the alarm logs extracted from the machines, technical design changes in the equipment and pre shift critical alarms checklist were proposed for the equipment maintenance. The given analysis is beneficial to allow OEMs or mine management to focus on the critical issues hampering the reliability of mine equipment and design necessary maintenance strategies to mitigate them.
Abstract: The use of nanostructured semiconducting material to catalyze degradation of environmental pollutants still receives much attention to date. One of the desired characteristics for pollutant degradation under ultra-violet visible light is the materials with extended carrier charge separation that allows for electronic transfer between the catalyst and the pollutants. In this work, zinc oxide n-type semiconductor vertically aligned structures were fabricated on silicon (100) substrates using the chemical bath deposition method. The as-synthesized structures were treated with nickel and sulphur. X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy were used to characterize the phase purity, structural dimensions and elemental composition of the obtained structures respectively. Photoluminescence emission measurements showed a decrease in both the near band edge emission as well as the defect band emission upon addition of nickel and sulphur with different concentrations. This was attributed to increased charger-carrier-separation due to the presence of Ni-S material on ZnO surface, which is linked to improved charge transfer during photocatalytic reactions.
Abstract: The choice evaluation between oil-immersed and dry-type transformers is often controlled by cost, location, and application. This paper compares the electrical performance of liquid- filled and dry-type transformers, which will assist the customer to choose the right and efficient ones for particular applications. An accurate assessment of the time-average flux density, electric field intensity and voltage distribution in an oil-insulated and a dry-type transformer have been computed and investigated. The detailed transformer modeling and analysis has been carried out to determine electrical parameter distributions. The models of oil-immersed and dry-type transformers are developed and solved by using the finite element method (FEM) to compare the electrical parameters. The effects of non-uniform and non-coherent voltage gradient, flux density and electric field distribution on the power losses and insulation properties of transformers are studied in detail. The results show that, for the same voltage and kilo-volt-ampere (kVA) rating, oil-immersed transformers have better insulation properties and less hysteresis losses than the dry-type.
Abstract: The problem of obesity is one that continues to be faced in the United States health care system and across the developing world. Prescription medications are available, but are often very expensive with minimal insurance coverage. The over-the-counter diet aid industry is a robust one, selling billions of dollars in products every year. It is important for clinicians to understand the myriad of different nutritional supplements marketed for obesity, and to weigh the evidence behind these products. This manuscript outlines the most commonly used nutritional supplements currently marketed for weight loss, reviewing the evidence with a focus on the efficacy and safety of these products.
Abstract: The aim of the paper is to explore the role of social marketing in changing the behavior of consumers on road safety, identify critical aspects and priority needs which impede the implementation of road safety program in Georgia. Given the goals of the study, a quantitative method was used to carry out interviews for primary data collection. This research identified the awareness level of road safety, legislation base, and marketing interventions to change behavior of drivers and pedestrians. During several years the non-governmental sector together with the local authorities and media have been very intensively working on the road safety issue in Georgia, but only seat-belts campaign should be considered rather successful. Despite achievements in this field, efficiency of road safety programs far from fulfillment and needs strong empowering.
Abstract: Many ophthalmologists can examine declines in visual sensitivity at arbitrary points on the retina using a precise perimetry device with a fundus camera function. However, the retinal layer causing the decline in visual sensitivity cannot be identified by this method. We studied an electroretinogram (ERG) function that can move the center of the multifocal hexagonal stimulus array in order to investigate cryptogenic diseases, such as macular dystrophy, acute zonal occult outer retinopathy, and multiple evanescent white dot syndrome. An electroretinographic optical system, specifically a perimetric optical system, was added to an experimental device carrying the same optical system as a fundus camera. We also added an infrared camera, a cold mirror, a halogen lamp, and a monitor. The software was generated to show the multifocal hexagonal stimulus array on the monitor using C++Builder XE8 and to move the center of the array up and down as well as back and forth. We used a multifunction I/O device and its design platform LabVIEW for data retrieval. The plate electrodes were used to measure electrodermal activities around the eyes. We used a multifocal hexagonal stimulus array with 37 elements in the software. The center of the multifocal hexagonal stimulus array could be adjusted to the same position as the examination target of the precise perimetry. We successfully added the moving ERG function to the experimental ophthalmologic device.
Abstract: The advancement in various concrete ingredients like plasticizers, additives and fibers, etc. has enabled concrete technologists to develop many viable varieties of special concretes in recent decades. Such various varieties of concrete have significant enhancement in green as well as hardened properties of concrete. A prudent selection of appropriate type of concrete can resolve many design and application issues in construction projects. This paper focuses on usage of self-compacting concrete, high early strength concrete, structural lightweight concrete, fiber reinforced concrete, high performance concrete and ultra-high strength concrete in the structures. The modified properties of strength at various ages, flowability, porosity, equilibrium density, flexural strength, elasticity, permeability etc. need to be carefully studied and incorporated into the design of the structures. The paper demonstrates various mixture combinations and the concrete properties that can be leveraged. The selection of such products based on the end use of structures has been proposed in order to efficiently utilize the modified characteristics of these concrete varieties. The study involves mapping the characteristics with benefits and savings for the structure from design perspective. Self-compacting concrete in the structure is characterized by high shuttering loads, better finish, and feasibility of closer reinforcement spacing. The structural design procedures can be modified to specify higher formwork strength, height of vertical members, cover reduction and increased ductility. The transverse reinforcement can be spaced at closer intervals compared to regular structural concrete. It allows structural lightweight concrete structures to be designed for reduced dead load, increased insulation properties. Member dimensions and steel requirement can be reduced proportionate to about 25 to 35 percent reduction in the dead load due to self-weight of concrete. Steel fiber reinforced concrete can be used to design grade slabs without primary reinforcement because of 70 to 100 percent higher tensile strength. The design procedures incorporate reduction in thickness and joint spacing. High performance concrete employs increase in the life of the structures by improvement in paste characteristics and durability by incorporating supplementary cementitious materials. Often, these are also designed for slower heat generation in the initial phase of hydration. The structural designer can incorporate the slow development of strength in the design and specify 56 or 90 days strength requirement. For designing high rise building structures, creep and elasticity properties of such concrete also need to be considered. Lastly, certain structures require a performance under loading conditions much earlier than final maturity of concrete. High early strength concrete has been designed to cater to a variety of usages at various ages as early as 8 to 12 hours. Therefore, an understanding of concrete performance specifications for special concrete is a definite door towards a superior structural design approach.
Abstract: Due to the numerous advantages of steel corrugated
web girders, its application field is growing for bridges as well as for
buildings. The global stability behavior of such girders is
significantly larger than those of conventional I-girders with flat web,
thus the application of the structural steel material can be
significantly reduced. Design codes and specifications do not provide
clear and complete rules or recommendations for the determination of
the lateral torsional buckling (LTB) resistance of corrugated web
girders. Therefore, the authors made a thorough investigation
regarding the LTB resistance of the corrugated web girders. Finite
element (FE) simulations have been performed to develop new
design formulas for the determination of the LTB resistance of
trapezoidally corrugated web girders. FE model is developed
considering geometrical and material nonlinear analysis using
equivalent geometric imperfections (GMNI analysis). The equivalent
geometric imperfections involve the initial geometric imperfections
and residual stresses coming from rolling, welding and flame cutting.
Imperfection sensitivity analysis was performed to determine the
necessary magnitudes regarding only the first eigenmodes shape
imperfections. By the help of the validated FE model, an extended
parametric study is carried out to investigate the LTB resistance for
different trapezoidal corrugation profiles. First, the critical moment of
a specific girder was calculated by FE model. The critical moments
from the FE calculations are compared to the previous analytical
calculation proposals. Then, nonlinear analysis was carried out to
determine the ultimate resistance. Due to the numerical
investigations, new proposals are developed for the determination of
the LTB resistance of trapezoidally corrugated web girders through a
modification factor on the design method related to the conventional
flat web girders.
Abstract: The purpose of the present research is to equate two
test forms as part of a study to evaluate the educational effectiveness
of the ARTé: Mecenas art history learning game. The researcher
applied Item Response Theory (IRT) procedures to calculate item,
test, and mean-sigma equating parameters. With the sample size
n=134, test parameters indicated “good” model fit but low Test
Information Functions and more acute than expected equating
parameters. Therefore, the researcher applied equipercentile equating
and linear equating to raw scores and compared the equated form
parameters and effect sizes from each method. Item scaling in IRT
enables the researcher to select a subset of well-discriminating items.
The mean-sigma step produces a mean-slope adjustment from the
anchor items, which was used to scale the score on the new form
(Form R) to the reference form (Form Q) scale. In equipercentile
equating, scores are adjusted to align the proportion of scores in each
quintile segment. Linear equating produces a mean-slope adjustment,
which was applied to all core items on the new form. The study
followed a quasi-experimental design with purposeful sampling of
students enrolled in a college level art history course (n=134) and
counterbalancing design to distribute both forms on the pre- and posttests.
The Experimental Group (n=82) was asked to play ARTé:
Mecenas online and complete Level 4 of the game within a two-week
period; 37 participants completed Level 4. Over the same period, the
Control Group (n=52) did not play the game. The researcher
examined between group differences from post-test scores on test
Form Q and Form R by full-factorial Two-Way ANOVA. The raw
score analysis indicated a 1.29% direct effect of form, which was
statistically non-significant but may be practically significant. The
researcher repeated the between group differences analysis with all
three equating methods. For the IRT mean-sigma adjusted scores,
form had a direct effect of 8.39%. Mean-sigma equating with a small
sample may have resulted in inaccurate equating parameters.
Equipercentile equating aligned test means and standard deviations,
but resultant skewness and kurtosis worsened compared to raw score
parameters. Form had a 3.18% direct effect. Linear equating
produced the lowest Form effect, approaching 0%. Using linearly
equated scores, the researcher conducted an ANCOVA to examine
the effect size in terms of prior knowledge. The between group effect
size for the Control Group versus Experimental Group participants
who completed the game was 14.39% with a 4.77% effect size
attributed to pre-test score. Playing and completing the game
increased art history knowledge, and individuals with low prior
knowledge tended to gain more from pre- to post test. Ultimately,
researchers should approach test equating based on their theoretical
stance on Classical Test Theory and IRT and the respective assumptions. Regardless of the approach or method, test equating
requires a representative sample of sufficient size. With small sample
sizes, the application of a range of equating approaches can expose
item and test features for review, inform interpretation, and identify
paths for improving instruments for future study.
Abstract: The world-wide population of people over 60 years
of age is growing rapidly. The explosion is placing increasingly
onerous demands on individual families, multiple industries and
entire countries. Current, human-intensive approaches to eldercare
are not sustainable, but IoT and AI technologies can help. The
Knowledge Reactor (KR) is a contextual, data fusion engine built to
address this and other similar problems. It fuses and centralizes IoT
and System of Record/Engagement data into a reactive knowledge
graph. Cognitive applications and services are constructed with its
multiagent architecture. The KR can scale-up and scaledown, because
it exploits container-based, horizontally scalable services for graph
store (JanusGraph) and pub-sub (Kafka) technologies. While the KR
can be applied to many domains that require IoT and AI technologies,
this paper describes how the KR specifically supports the challenging
domain of cognitive eldercare. Rule- and machine learning-based
analytics infer activities of daily living from IoT sensor readings. KR
scalability, adaptability, flexibility and usability are demonstrated.
Abstract: Jesus and Socrates shared a remarkable gift; a channel of inner spiritual communication, to afford them truthful guidance in their respective religious discourse. Jesus is part of the Trinity; he is the Son, the Son of God. In mortal life he is the son of a carpenter. He called on all peoples to repent of their sins but fell foul of the authorities and was crucified. Socrates was an ancient Greek philosopher and the son of an artisan. His mission is to drive the Athenians to investigate truth, but he too incurs the displeasure of fellow citizens, to the extent of execution. The accusations made against them centre around, in Jesus’ case, proclaiming himself the Son of God, with the means to pardon, and in Socrates’, that a daimonion, an inner voice, speaks to him in his heart. Jesus talks with God directly through prayer, as the pneuma of God, i.e. to pneuma to hagion, or Holy Spirit, is with him. Socrates seems to enter what we would now think of as a trance-like condition, wherein he communicates with his inner daimonion, who directs him to take courage on the righteous path.
Abstract: The psychological present has an actual extension.
When a sequence of instantaneous stimuli falls in this short interval
of time, observers perceive a compresence of events in succession
and the temporal order depends on the qualitative relationships
between the perceptual properties of the events. Two experiments
were carried out to study the influence of perceptual grouping, with
and without temporal displacement, on the duration of auditory
sequences. The psychophysical method of adjustment was adopted.
The first experiment investigated the effect of temporal displacement
of a white noise on sequence duration. The second experiment
investigated the effect of temporal displacement, along the pitch
dimension, on temporal shortening of sequence. The results suggest
that the temporal order of sounds, in the case of temporal
displacement, is organized along the pitch dimension.
Abstract: A crucial component to the success of any financial advising relationship is for the financial professional to understand the perceptions, preferences and thought-processes carried by the financial clients they serve. Armed with this information, financial professionals are more quickly able to understand how they can tailor their approach to best match the individual preferences and needs of each personal investor. Our research explores the use of a quantitative assessment tool in the financial services industry to assist in the identification of the personal investor’s consumer behaviors, especially in terms of financial risk tolerance, as it relates to their financial decision making. Through this process, the Unitifi Consumer Insight Tool (UCIT) was created and refined to capture and categorize personal investor financial behavioral categories and the financial personality tendencies of individuals prior to the initiation of a financial advisement relationship. This paper discusses the use of this tool to place individuals in one of four behavior-based financial risk tolerance categories. Our discoveries and research were aided through administration of a web-based survey to a group of over 1,000 individuals. Our findings indicate that it is possible to use a quantitative assessment tool to assist in predicting the behavioral tendencies of personal consumers when faced with consumer financial risk and decisions.
Abstract: With recent trends in Big Data and advancements
in Information and Communication Technologies, the healthcare
industry is at the stage of its transition from clinician oriented to
technology oriented. Many people around the world die of cancer
because the diagnosis of disease was not done at an early stage.
Nowadays, the computational methods in the form of Machine
Learning (ML) are used to develop automated decision support
systems that can diagnose cancer with high confidence in a timely
manner. This paper aims to carry out the comparative evaluation
of a selected set of ML classifiers on two existing datasets: breast
cancer and cervical cancer. The ML classifiers compared in this study
are Decision Tree (DT), Support Vector Machine (SVM), k-Nearest
Neighbor (k-NN), Logistic Regression, Ensemble (Bagged Tree) and
Artificial Neural Networks (ANN). The evaluation is carried out based
on standard evaluation metrics Precision (P), Recall (R), F1-score and
Accuracy. The experimental results based on the evaluation metrics
show that ANN showed the highest-level accuracy (99.4%) when
tested with breast cancer dataset. On the other hand, when these
ML classifiers are tested with the cervical cancer dataset, Ensemble
(Bagged Tree) technique gave better accuracy (93.1%) in comparison
to other classifiers.
Abstract: The rapid progress of technology in today's competitive conditions has also accelerated companies' technology development activities. As a result, companies are paying more attention to R&D studies and are beginning to allocate a larger share to R&D projects. A more systematic, comprehensive, target-oriented implementation of R&D studies is crucial for the company to achieve successful results. As a consequence, Technology Roadmap (TRM) is gaining importance as a management tool. It has critical prospects for achieving medium and long term success as it contains decisions about past business, future plans, technological infrastructure. When studies on TRM are examined, projects to be placed on the roadmap are selected by many different methods. Generally preferred methods are based on multi-criteria decision making methods. Management of selected projects becomes an important point after the selection phase of the projects. At this stage, TRM are used. TRM can be created in many different ways so that each institution can prepare its own Technology Roadmap according to their strategic plan. Depending on the intended use, there can be TRM with different layers at different sizes. In the evaluation phase of the R&D projects and in the creation of the TRM, HAVELSAN, Turkey's largest defense company in the software field, carries out this process with great care and diligence. At the beginning, suggested R&D projects are evaluated by the Technology Management Board (TMB) of HAVELSAN in accordance with the company's resources, objectives, and targets. These projects are presented to the TMB periodically for evaluation within the framework of certain criteria by board members. After the necessary steps have been passed, the approved projects are added to the time-based TRM, which is composed of four layers as market, product, project and technology. The use of a four-layered roadmap provides a clearer understanding and visualization of company strategy and objectives. This study demonstrates the benefits of using TRM, four-layered Technology Roadmapping and the possibilities for the institutions in the defense industry.
Abstract: Low-temperature waste heat is abundant in the process industries, and large amounts of Liquefied Natural Gas (LNG) cold energy are discarded without being recovered properly in LNG terminals. Power generation is an effective way to utilize low-temperature waste heat and LNG cold energy simultaneously. Organic Rankine Cycles (ORCs) and CO2 power cycles are promising technologies to convert low-temperature waste heat and LNG cold energy into electricity. If waste heat and LNG cold energy are utilized simultaneously in one system, the performance may outperform separate systems utilizing low-temperature waste heat and LNG cold energy, respectively. Low-temperature waste heat acts as the heat source and LNG regasification acts as the heat sink in the combined system. Due to the large temperature difference between the heat source and the heat sink, cascaded power cycle configurations are proposed in this paper. Cascaded power cycles can improve the energy efficiency of the system considerably. The cycle operating at a higher temperature to recover waste heat is called top cycle and the cycle operating at a lower temperature to utilize LNG cold energy is called bottom cycle in this study. The top cycle condensation heat is used as the heat source in the bottom cycle. The top cycle can be an ORC, transcritical CO2 (tCO2) cycle or supercritical CO2 (sCO2) cycle, while the bottom cycle only can be an ORC due to the low-temperature range of the bottom cycle. However, the thermodynamic path of the tCO2 cycle and sCO2 cycle are different from that of an ORC. The tCO2 cycle and the sCO2 cycle perform better than an ORC for sensible waste heat recovery due to a better temperature match with the waste heat source. Different combinations of the tCO2 cycle, sCO2 cycle and ORC are compared to screen the best configurations of the cascaded power cycles. The influence of the working fluid and the operating conditions are also investigated in this study. Each configuration is modeled and optimized in Aspen HYSYS. The results show that cascaded tCO2/ORC performs better compared with cascaded ORC/ORC and cascaded sCO2/ORC for the case study.
Abstract: Induction assisted single point incremental forming
(IASPIF) is a flexible method and can be simply utilized to
form a high strength alloys. Due to the interaction between the
mechanical and thermal properties during IASPIF an evaluation for
the process is necessary to be performed analytically. Therefore, a
numerical simulation was carried out in this paper. The numerical
analysis was operated at both room and elevated temperatures
then compared with experimental results. Fully coupled dynamic
temperature displacement explicit analysis was used to simulated the
hot single point incremental forming. The numerical analysis was
indicating that during hot single point incremental forming were a
combination between complicated compression, tension and shear
stresses. As a result, the equivalent plastic strain was increased
excessively by rising both the formed part depth and the heating
temperature during forming. Whereas, the forming forces were
decreased from 5 kN at room temperature to 0.95 kN at elevated
temperature. The simulation shows that the maximum true strain was
occurred in the stretching zone which was the same as in experiment.