Abstract: In this numerical work, mixed convection and entropy
generation of Cu–water nanofluid in a lid-driven square cavity have
been investigated numerically using the Lattice Boltzmann Method.
Horizontal walls of the cavity are adiabatic and vertical walls have
constant temperature but different values. The top wall has been
considered as moving from left to right at a constant speed, U0. The
effects of different parameters such as nanoparticle volume
concentration (0–0.05), Rayleigh number (104–106) and Reynolds
numbers (1, 10 and 100) on the entropy generation, flow and
temperature fields are studied. The results have shown that addition
of nanoparticles to the base fluid affects the entropy generation, flow
pattern and thermal behavior especially at higher Rayleigh and low
Reynolds numbers. For pure fluid as well as nanofluid, the increase
of Reynolds number increases the average Nusselt number and the
total entropy generation, linearly. The maximum entropy generation
occurs in nanofluid at low Rayleigh number and at high Reynolds
number. The minimum entropy generation occurs in pure fluid at low
Rayleigh and Reynolds numbers. Also at higher Reynolds number,
the effect of Cu nanoparticles on enhancement of heat transfer was
decreased because the effect of lid-driven cavity was increased. The
present results are validated by favorable comparisons with
previously published results. The results of the problem are presented
in graphical and tabular forms and discussed.
Abstract: Operation enhancement in an air cooler depends on
rate of heat transfer, and pressure drop. In this paper for a given heat
duty, study of the effects of FPI (Fin Per Inch) and fin type (circular
and hexagonal fins) on heat transfer, and pressure drop in an air
cooler in Iran, Arvand petrochemical. A program in EES
(Engineering Equations Solver) software moreover, Aspen B-JAC
and HTFS+ softwares are used for this purpose to solve governing
equations. At first the simulated results obtained from this program is
compared to the experimental data for two cases of FPI. The effects
of FPI from 3 to 15 over heat transfer (Q) to pressure drop ratio
(Q/Δp ratio). This ratio is one of the main parameters in design, and
simulation heat exchangers. The results show that heat transfer (Q)
and pressure drop increase with increasing FPI steadily, and the Q/Δp
ratio increases to FPI=12 and then decreased gradually to FPI=15,
and Q/Δp ratio is maximum at FPI=12. The FPI value selection
between 8 and 12 obtained as a result to optimum heat transfer to
pressure drop ratio. Also by contrast, between circular and hexagonal
fins results, the Q/Δp ratio of hexagonal fins more than Q/Δp ratio of
circular fins for FPI between 8 and 12 (optimum FPI)
Abstract: Tannins are a unique category of plant phytochemicals
especially in terms of their vast potential health-benefiting properties.
Researchers have described the capacity of tannins to enhance
glucose uptake and inhibit adipogenesis, thus being potential drugs
for the treatment of non-insulin dependent diabetes mellitus. Thus,
the present research was conducted to find out tannin content of food
products. The percentage of tannin in various analyzed sources
ranged from 0.0 to 108.53%; highest in kathaa and lowest in ker and
mango bark. The percentage of tannins present in the plants,
however, varies. Numerous studies have confirmed that the naturally
occurring polyphenols are key factor for the beneficial effects of the
herbal medicines. Isolation and identification of active constituents
from plants, preparation of standardized dose & dosage regimen can
play a significant role in improving the hypoglycaemic action.
Abstract: The latest years the number of immigrants at Greece
has increased dramatically. Their impact on the National Health
System (NHS) has not been yet thoroughly investigated. This paper
analyses the cost of immigrants to the NHS hospitals of the region of
Eastern Macedonia and Thrace. The data are collected from 2005 to
2011 from five different hospitals and are analysed using linear
mixed effects models in order to investigate the effects of nationality
and year on the cost of hospitalization and treatment. The results
show that generally the Greek nationality patients have a higher mean
cost of hospitalization compared to the immigrants and that there is
an increasing trend for the cost except for the year 2010.
Abstract: This work explores the inter-region investment
behaviors of Integrated Circuit (IC) design industry from Taiwan to
China using the amount of foreign direct investment (FDI). According
to the mutual dependence among different IC design industrial
locations, Lotka-Volterra model is utilized to explore the FDI
interactions between South and East China. Effects of inter-regional
collaborations on FDI flows into China are considered. The analysis
results show that FDIs into South China for IC design industry
significantly inspire the subsequent FDIs into East China, while FDIs
into East China for Taiwan’s IC design industry significantly hinder
the subsequent FDIs into South China. Because the supply chain along
IC industry includes upstream IC design, midstream manufacturing, as
well as downstream packing and testing enterprises, IC design industry
has to cooperate with IC manufacturing, packaging and testing
industries in the same area to form a strong IC industrial cluster.
Taiwan’s IC design industry implement the largest FDI amount into
East China and the second largest FDI amount into South China
among the four regions: North, East, Mid-West and South China. If IC
design houses undertake more FDIs in South China, those in East
China are urged to incrementally implement more FDIs into East
China to maintain the competitive advantages of the IC supply chain in
East China. On the other hand, as the FDIs in East China rise, the FDIs
in South China will successively decline since capitals have
concentrated in East China. In addition, this investigation proves that
the prediction of Lotka-Volterra model in FDI trends is accurate
because the industrial interactions between the two regions are
included. Finally, this work confirms that the FDI flows cannot reach a
stable equilibrium point, so the FDI inflows into East and South China
will expand in the future.
Abstract: Environmental and functional conditions, sometimes,
necessitate the architectural plan of the building to be asymmetric,
and this result in an asymmetric structure. In such cases finding an
optimal pattern for locating the components of lateral load bearing
system, including shear walls, in the building’s plan is desired. In
case of shear wall in addition to the location the shape of the wall
cross-section is also an effective factor. Various types of shear walls
and their proper layout might come effective in better stiffness
distribution and more appropriate seismic response of the building.
Several studies have been conducted in the context of analysis and
design of shear walls; however, few studies have been performed on
making decisions for the location and form of shear walls in multistory
buildings, especially those with irregular plan. In this study, an
attempt has been made to obtain the most reliable seismic behavior of
multi-story reinforced concrete vertically chamfered buildings by
using more appropriate shear walls form and arrangement in 7-, 10-,
12-, and 15-stoy buildings. The considered forms and arrangements
include common rectangular walls and L-, T-, U- and Z-shaped plan,
located as the core or in the outer frames of the building structure.
Comparison of seismic behaviors of the buildings, including
maximum roof displacement and particularly formation of plastic
hinges and their distribution in the buildings’ structures, have been
done based on the results of a series of nonlinear time history
analyses, by using a set of selected earthquake records. Results show
that shear walls with U-shaped cross-section, placed as the building
central core, and also walls with Z-shaped cross-section, placed at the
corners give the building more reliable seismic behavior.
Abstract: Comparative analysis of the properties of melon seed,
coconut fruit and their oil yield were evaluated in this work using
standard analytical technique AOAC. The results of the analysis
carried out revealed that the moisture contents of the samples studied
are 11.15% (melon) and 7.59% (coconut). The crude lipid content are
46.10% (melon) and 55.15% (coconut).The treatment combinations
used (leaching time, leaching temperature and solute: solvent ratio)
showed significant difference (p < 0.05) in yield between the
samples, with melon oil seed flour having a higher percentage range
of oil yield (41.30 – 52.90%) and coconut (36.25 – 49.83%). The
physical characterization of the extracted oil was also carried out.
The values gotten for refractive index are 1.487 (melon seed oil) and
1.361 (coconut oil) and viscosities are 0.008 (melon seed oil) and
0.002 (coconut oil). The chemical analysis of the extracted oils shows
acid value of 1.00mg NaOH/g oil (melon oil), 10.050mg NaOH/g oil
(coconut oil) and saponification value of 187.00mg/KOH (melon oil)
and 183.26mg/KOH (coconut oil). The iodine value of the melon oil
gave 75.00mg I2/g and 81.00mg I2/g for coconut oil. A standard
statistical package Minitab version 16.0 was used in the regression
analysis and analysis of variance (ANOVA). The statistical software
mentioned above was also used to optimize the leaching process.
Both samples gave high oil yield at the same optimal conditions. The
optimal conditions to obtain highest oil yield ≥ 52% (melon seed)
and ≥ 48% (coconut seed) are solute - solvent ratio of 40g/ml,
leaching time of 2hours and leaching temperature of 50oC. The two
samples studied have potential of yielding oil with melon seed giving
the higher yield.
Abstract: Inference plays an important role in the learning
process and it can lead to a rapid acquisition of a second language.
When learning a non-native language i.e., a critical language like
Arabic, the students depend on the teacher’s support most of the time
to learn new concepts. The students focus on memorizing the new
vocabulary and stress on learning all the grammatical rules. Hence,
the students became mechanical and cannot produce the language
easily. As a result, they are unable to predicate the meaning of words
in the context by relying heavily on the teacher, in that they cannot
link their prior knowledge or even identify the meaning of the words
without the support of the teacher. This study explores how the
teacher guides students learning during the inference process and
what are the processes of learning that can direct student’s inference.
Abstract: Analyzing the relation networks between the hospital
buildings which have complex structure and distinctive spatial
relationships is quite difficult. The hospital buildings which require
specialty in spatial relationship solutions during design and selfinnovation
through the developing technology should survive and
keep giving service even after the disasters such as earthquakes. In
this study, a hospital building where the load-bearing system was
strengthened because of the insufficient earthquake performance and
the construction of an additional building was required to meet the
increasing need for space was discussed and a comparative spatial
evaluation of the hospital building was made with regard to its status
before the change and after the change. For this reason, spatial
organizations of the building before change and after the change were
analyzed by means of Space Syntax method and the effects of the
change on space organization parameters were searched by applying
an analytical procedure. Using Depthmap UCL software,
Connectivity, Visual Mean Depth, Beta and Visual Integration
analyses were conducted. Based on the data obtained after the
analyses, it was seen that the relationships between spaces of the
building increased after the change and the building has become more
explicit and understandable for the occupants. Furthermore, it was
determined according to findings of the analysis that the increase in
depth causes difficulty in perceiving the spaces and the changes
considering this problem generally ease spatial use.
Abstract: This research studies the joint production,
maintenance and subcontracting control policy for an unreliable
deteriorating manufacturing system. Production activities are
controlled by a derivation of the Hedging Point Policy, and given that
the system is subject to deterioration, it reduces progressively its
capacity to satisfy product demand. Multiple deterioration effects are
considered, reflected mainly in the quality of the parts produced and
the reliability of the machine. Subcontracting is available as support
to satisfy product demand; also, overhaul maintenance can be
conducted to reduce the effects of deterioration. The main objective
of the research is to determine simultaneously the production,
maintenance and subcontracting rate, which minimize the total,
incurred cost. A stochastic dynamic programming model is
developed and solved through a simulation-based approach
composed of statistical analysis and optimization with the response
surface methodology. The obtained results highlight the strong
interactions between production, deterioration and quality, which
justify the development of an integrated model. A numerical example
and a sensitivity analysis are presented to validate our results.
Abstract: Home Energy Management System (HEMS), which makes the residential consumers, contribute to the demand response is attracting attention in recent years. An aim of HEMS is to minimize their electricity cost by controlling the use of their appliances according to electricity price. The use of appliances in HEMS may be affected by some conditions such as external temperature and electricity price. Therefore, the user’s usage pattern of appliances should be modeled according to the external conditions, and the resultant usage pattern is related to the user’s comfortability on use of each appliances. This paper proposes a methodology to model the usage pattern based on the historical data with the copula function. Through copula function, the usage range of each appliance can be obtained and is able to satisfy the appropriate user’s comfort according to the external conditions for next day. Within the usage range, an optimal scheduling for appliances would be conducted so as to minimize an electricity cost with considering user’s comfort. Among the home appliance, electric heater (EH) is a representative appliance, which is affected by the external temperature. In this paper, an optimal scheduling algorithm for an electric heater (EH) is addressed based on the method of branch and bound. As a result, scenarios for the EH usage are obtained according to user’s comfort levels and then the residential consumer would select the best scenario. The case study shows the effects of the proposed algorithm compared with the traditional operation of the EH, and it represents impacts of the comfort level on the scheduling result.
Abstract: The Gezi Park protests of 2013 have significantly changed the Turkish agenda and its effects have been felt historically. The protests, which rapidly spread throughout the country, were triggered by the proposal to recreate the Ottoman Army Barracks to function as a shopping mall on Gezi Park located in Istanbul’s Taksim neighbourhood despite the oppositions of several NGOs and when trees were cut in the park for this purpose. Once the news that the construction vehicles entered the park on May 27 spread on social media, activists moved into the park to stop the demolition, against whom the police used disproportioned force. With this police intervention and the then prime-minister Tayyip Erdoğan's insistent statements about the construction plans, the protests turned into anti- government demonstrations, which then spread to the rest of the country, mainly in big cities like Ankara and Izmir. According to the Ministry of Internal Affairs’ June 23rd reports, 2.5 million people joined the demonstrations in 79 provinces, that is all of them, except for the provinces of Bayburt and Bingöl, while even more people shared their opinions via social networks. As a result of these events, 8 civilians and 2 security personnel lost their lives, namely police chief Mustafa Sarı, police officer Ahmet Küçükdağ, citizens Mehmet Ayvalıtaş, Abdullah Cömert, Ethem Sarısülük, Ali İsmail Korkmaz, Ahmet Atakan, Berkin Elvan, Burak Can Karamanoğlu, Mehmet İstif, and Elif Çermik, and 8163 more were injured. Besides being a turning point in Turkish history, the Gezi Park protests also had broad repercussions in both in Turkish and in global media, which focused on Turkey throughout the events. Our study conducts content analysis of three Turkish reporting newspapers with varying ideological standpoints, Hürriyet, Cumhuriyet ve Yeni Şafak, in order to reveal their basic approach to news casting in context of the Gezi Park protests. Headlines, news segments, and news content relating to the Gezi protests were treated and analysed for this purpose. The aim of this study is to understand the social effects of the Gezi Park protests through media samples with varying political attitudes towards news casting.
Abstract: Plate is one of the popular structural elements used in a wide range of industries and structures. They may be subjected to blast loads during explosion events, missile attacks or aircraft attacks. This study is to investigate dynamic responses of the rectangular plate subjected to explosive loads. The effects of material properties and plate thickness on responses of the plate are to be investigated. The compressive pressure is applied to the surface of the plate. Different amounts of thickness in the range from 1mm to 30mm are considered for the plate to evaluate the changes in responses of the plate with respect to plate thickness. Two different properties are considered for the steel. First, the analysis is performed by considering only the elastic-plastic properties for the steel plate. Later on damping is considered to investigate its effects on the responses of the plate. To do analysis, numerical method using a finite element based package ABAQUS is applied. Finally, dynamic responses and graphs showing the relation between maximum displacement of the plate and aim parameters are provided.
Abstract: In the past few years, high consumption of soft drinks
has attracted negative attention world-wide due to its possible
adverse effects, leading the health conscious people to find
alternative nutraceutical or herbal health drinks. In the present study,
a nutraceutical soft drink was developed utilizing some easily
available and well known traditional herbs having nutritional
potential. The key ingredients were selected as bael, amla, lemon
juice, ashwagandha and poppy seeds based on their household routine
use in the summer with proven refreshing, cooling and energetic
feeling since ages. After several trials made, the final composition of
nutraceutical summer soft drink was selected as most suitable
combination based on the taste, physicochemical, microbial and
organoleptic point of view. The physicochemical analysis of the
prepared drink found to contain optimum level of titratable acidity,
total soluble solids and pH which were in accordance of the
commercial recommendations. There were no bacterial colonies
found in the product therefore found within limits. During the nine
point’s hedonic scale sensory evaluation, the drink was strongly liked
for colour, taste, flavour and texture. The formulation was found to
contain flavonoids (80mg/100ml), phenolics (103mg/100ml), vitamin
C (250mg/100ml) and has antioxidant potential (75.52%) apart from
providing several other essential vitamins, minerals and healthy
components. The developed nutraceutical drink provides an
economical and feasible option for the consumers with very good
taste combined with potential health benefits. The present drink is
potentially capable to replace the synthetic soft drinks available in the
market.
Abstract: The purpose of this paper is to examine the effects and
relationship of stress and social support towards the quality of life
among flood victims in Malaysia. A total of 764 respondents took
part in the survey via convenience sampling. The Depression,
Anxiety and Stress scale (DASS) was utilized to measure stress while
The Multidimensional Scale of Perceived Social Support was used to
measure social support. To measure quality of life, the combination
of WHO Quality of Life – BREF (WHOQOL-BREF) and The Impact
of Event Scale – Revised (IES-R) were utilized. The findings of this
study indicate that there were significant correlations between
variables in the study. The findings showed a significant negative
relation between stress and quality of life; and significant positive
correlations between support from family as well as support from
friends with quality of life. Stress and support from family were
found to be significant predictors that influence the quality of life
among flood victims.
Abstract: Due to the interference effects, the intrinsic
aerodynamic parameters obtained from the individual component
testing are always fundamentally different than those obtained for
complete model testing. Consideration and limitation for such testing
need to be taken into account in any design work related to the
component buildup method. In this paper, the scaled model of a
straight rectangular canard of a hybrid buoyant aircraft is tested at 50
m/s in IIUM-LSWT (Low Speed Wind Tunnel). Model and its
attachment with the balance are kept rigid to have results free from
the aeroelastic distortion. Based on the velocity profile of the test
section’s floor; the height of the model is kept equal to the
corresponding boundary layer displacement. Balance measurements
provide valuable but limited information of overall aerodynamic
behavior of the model. Zero lift coefficient is obtained at -2.2o and
the corresponding drag coefficient was found to be less than that at
zero angle of attack. As a part of the validation of low fidelity tool,
plot of lift coefficient plot was verified by the experimental data and
except the value of zero lift coefficients, the overall trend has under
predicted the lift coefficient. Based on this comparative study, a
correction factor of 1.36 is proposed for lift curve slope obtained
from the panel method.
Abstract: Salinity is one of the major factors limiting crop
production in an arid environment. Despite its global importance
soybean production suffer the problems of salinity stress causing
damages at plant development. So it is implacable to either search for
salinity enhancement of soybean plants. Therefore, in the current
study we try to clarify the mechanism that might be involved in the
ameliorating effects of osmo-protectants such as proline and glycine
betaine as well as, compost application on soybean plants grown
under salinity stress. The experiment was conducted under
greenhouse conditions at the Graduate School of Biosphere Science
Laboratory of Hiroshima University, Japan in 2011. The experiment
was designed as a spilt-split plot based on randomized complete
block design with four replications. The treatments could be
summarized as follows; (i) salinity concentrations (0 and 15 mM), (ii)
compost treatments (0 and 24 t ha-1) and (iii) the exogenous, proline
and glycine betaine concentrations (0 mM and 25 mM) for each.
Results indicated that salinity stress induced reduction in growth and
physiological aspects (dry weight per plant, chlorophyll content, N
and K+ content) of soybean plant compared with those of the
unstressed plants. On the other hand, salinity stress led to increases in
the electrolyte leakage ratio, Na and proline contents. Special
attention was paid to, the tolerance against salt stress was observed,
the improvement of salt tolerance resulted from proline, glycine
betaine and compost were accompanied with improved K+, and
proline accumulation. While, significantly decreased electrolyte
leakage ratio and Na+ content. These results clearly demonstrate that
harmful effect of salinity could reduce on growth aspects of soybean.
Consequently, exogenous osmoprotectants combine with compost
will effectively solve seasonal salinity stress problem and are a good
strategy to increase salinity resistance of soybean in the drylands.
Abstract: MHD chemically reacting viscous fluid flow towards
a vertical surface with slip and convective boundary conditions has
been conducted. The temperature and the chemical species
concentration of the surface and the velocity of the external flow are
assumed to vary linearly with the distance from the vertical surface.
The governing differential equations are modeled and transformed
into systems of ordinary differential equations, which are then solved
numerically by a shooting method. The effects of various parameters
on the heat and mass transfer characteristics are discussed. Graphical
results are presented for the velocity, temperature, and concentration
profiles whilst the skin-friction coefficient and the rate of heat and
mass transfers near the surface are presented in tables and discussed.
The results revealed that increasing the strength of the magnetic field
increases the skin-friction coefficient and the rate of heat and mass
transfers toward the surface. The velocity profiles are increased
towards the surface due to the presence of the Lorenz force, which
attracts the fluid particles near the surface. The rate of chemical
reaction is seen to decrease the concentration boundary layer near the
surface due to the destructive chemical reaction occurring near the
surface.
Abstract: At the present time, awareness, education, computer
simulation and information systems protection are very serious and
relevant topics. The article deals with perspectives and possibilities of
implementation of emergence or natural hazard threats into the
system which is developed for communication among members of
crisis management staffs. The Czech Hydro-Meteorological Institute
with its System of Integrated Warning Service resents the largest
usable base of information. National information systems are connected to foreign systems,
especially to flooding emergency systems of neighboring countries,
systems of European Union and international organizations where the
Czech Republic is a member. Use of outputs of particular information
systems and computer simulations on a single communication
interface of information system for communication among members
of crisis management staff and setting the site interoperability in the
net will lead to time savings in decision-making processes in solving
extraordinary events and crisis situations. Faster managing of an
extraordinary event or a crisis situation will bring positive effects and
minimize the impact of negative effects on the environment.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.