Abstract: This article is trying to determine the status of flue gas
that is entering the KWH heat exchanger from combustion chamber
in order to calculate the heat transfer ratio of the heat exchanger.
Combination of measurement, calculation and computer simulation
was used to create a useful way to approximate the heat transfer rate.
The measurements were taken by a number of sensors that are
mounted on the experimental device and by a thermal imaging
camera. The results of the numerical calculation are in a good
correspondence with the real power output of the experimental
device. That result shows that the research has a good direction and
can be used to propose changes in the construction of the heat
exchanger, but still needs enhancements.
Abstract: This study examines analytically the effect of tsunami loads on reinforced concrete (RC) frame buildings. The impact of tsunami wave loads and waterborne objects are analyzed using a typical substandard full-scale two-story RC frame building tested as part of the EU-funded Ecoleader project. The building was subjected to shake table tests in bare condition, and subsequently strengthened using Carbon Fiber Reinforced Polymers (CFRP) composites and retested. Numerical models of the building in both bare and CFRP-strengthened conditions are calibrated in DRAIN-3DX software to match the test results. To investigate the response of wave loads and impact forces, the numerical models are subjected to nonlinear dynamic analyses using force time-history input records. The analytical results are compared in terms of displacements at the floors and at the “impact point” of a boat. The results show that the roof displacement of the CFRP-strengthened building reduced by 63% when compared to the bare building. The results also indicate that strengthening only the mid-height of the impact column using CFRP is more effective at reducing damage when compared to strengthening other parts of the column. Alternative solutions to mitigate damage due to tsunami loads are suggested.
Abstract: This paper describes an analysis of Yacht Simulator
international trends and also explains about Yacht. The results are
summarized as follows. Attached to the cockpit are sensors that feed
-back information on rudder angle, boat heel angle and mainsheet
tension to the computer. Energy expenditure of the sailor measure
indirectly using expired gas analysis for the measurement of VO2 and
VCO2. At sea course configurations and wind conditions can be preset
to suit any level of sailor from complete beginner to advanced sailor.
Abstract: This paper presents the simulation results of the
effects of sampling frequency on the total harmonic distortion (THD)
of three-phase inverters using the space vector pulse width
modulation (SVPWM) and space vector control (SVC) algorithms.
The relationship between the variables was studied using curve fitting
techniques, and it has been shown that, for 50 Hz inverters, there is
an exponential relation between the sampling frequency and THD up
to around 8500 Hz, beyond which the performance of the model
becomes irregular, and there is an negative exponential relation
between the sampling frequency and the marginal improvement to
the THD. It has also been found that the performance of SVPWM is
better than that of SVC with the same sampling frequency in most
frequency range, including the range where the performance of the
former is irregular.
Abstract: The air transport impact on environment is more than
ever a limitative obstacle to the aeronautical industry continuous
growth. Over the last decades, considerable effort has been carried
out in order to obtain quieter aircraft solutions, whether by changing
the original design or investigating more silent maneuvers. The
noise propagated by rotating surfaces is one of the most important
sources of annoyance, being present in most aerial vehicles. Bearing
this is mind, CEIIA developed a new computational chain for
noise prediction with in-house software tools to obtain solutions in
relatively short time without using excessive computer resources. This
work is based on the new acoustic tool, which aims to predict the
rotor noise generated during steady and maneuvering flight, making
use of the flexibility of the C language and the advantages of GPU
programming in terms of velocity. The acoustic tool is based in the
Formulation 1A of Farassat, capable of predicting two important
types of noise: the loading and thickness noise. The present work
describes the most important features of the acoustic tool, presenting
its most relevant results and framework analyses for helicopters and
UAV quadrotors.
Abstract: This paper presents an efficient fusion algorithm for
iris images to generate stable feature for recognition in unconstrained
environment. Recently, iris recognition systems are focused on real
scenarios in our daily life without the subject’s cooperation. Under
large variation in the environment, the objective of this paper is to
combine information from multiple images of the same iris. The
result of image fusion is a new image which is more stable for further
iris recognition than each original noise iris image. A wavelet-based
approach for multi-resolution image fusion is applied in the fusion
process. The detection of the iris image is based on Adaboost
algorithm and then local binary pattern (LBP) histogram is then
applied to texture classification with the weighting scheme.
Experiment showed that the generated features from the proposed
fusion algorithm can improve the performance for verification system
through iris recognition.
Abstract: This paper examines how “Zakat” provides fair
income redistribution and aids the struggle against poverty. Providing
fair income redistribution and combating poverty constitutes some of
the fundamental tasks performed by countries all over the world.
Each country seeks a solution for these problems according to their
political, economic and administrative styles through applying
various economic and financial policies. The same situation can be
handled via “zakat” association in Islam. Nowadays, we observe
different versions of “zakat” in developed countries. Applications
such as negative income tax denote merely a different form of
“zakat” that is being applied almost in the same way but under
changed names. However, the minimum values to donate under zakat
(e.g. 85 gr. gold and 40 animals) get altered and various amounts are
put into practice. It might be named as negative income tax instead of
zakat, nonetheless, these applications are based on the Holy Koran
and the hadith released 1400 years ago. Besides, considering the
savage and slavery in the world at those times, we might easily
recognize the true value of the zakat being applied for the first time
then in the Islamic system. Through zakat, governments are able to
transfer incomes to the poor as a means of enabling them achieve the
minimum standard of living required. With regards to who benefits
from the Zakat, an objective and fair criteria was used to determine
who benefits from the zakat contrary to the notion that it was based
on peoples’ own choices. Since the zakat is obligatory, the transfers
do not get forwarded directly but via the government and get
distributed, which requires vast governmental organizations. Through
the application of Zakat, reduced levels of poverty can be achieved
and also ensure the fair income redistribution.
Abstract: Estimation of model parameters is necessary to predict
the behavior of a system. Model parameters are estimated using
optimization criteria. Most algorithms use historical data to estimate
model parameters. The known target values (actual) and the output
produced by the model are compared. The differences between the
two form the basis to estimate the parameters. In order to compare
different models developed using the same data different criteria are
used. The data obtained for short scale projects are used here. We
consider software effort estimation problem using radial basis
function network. The accuracy comparison is made using various
existing criteria for one and two predictors. Then, we propose a new
criterion based on linear least squares for evaluation and compared
the results of one and two predictors. We have considered another
data set and evaluated prediction accuracy using the new criterion.
The new criterion is easy to comprehend compared to single statistic.
Although software effort estimation is considered, this method is
applicable for any modeling and prediction.
Abstract: Biofuels production has come forth as a future
technology to combat the problem of depleting fossil fuels. Bio-based
ethanol production from enzymatic lignocellulosic biomass
degradation serves an efficient method and catching the eye of
scientific community. High cost of the enzyme is the major obstacle
in preventing the commercialization of this process. Thus main
objective of the present study was to optimize composition of
medium components for enhancing cellulase production by newly
isolated strain of Bacillus tequilensis. Nineteen factors were taken
into account using statistical Plackett-Burman Design. The significant
variables influencing the cellulose production were further employed
in statistical Response Surface Methodology using Central
Composite Design for maximizing cellulase production. The
optimum medium composition for cellulase production was: peptone
(4.94 g/L), ammonium chloride (4.99 g/L), yeast extract (2.00 g/L),
Tween-20 (0.53 g/L), calcium chloride (0.20 g/L) and cobalt chloride
(0.60 g/L) with pH 7, agitation speed 150 rpm and 72 h incubation at
37oC. Analysis of variance (ANOVA) revealed high coefficient of
determination (R2) of 0.99. Maximum cellulase productivity of 11.5
IU/ml was observed against the model predicted value of 13 IU/ml.
This was found to be optimally active at 60oC and pH 5.5.
Abstract: It is important to take security measures to protect
your computer information, reduce identify theft, and prevent from
malicious cyber-attacks. With cyber-attacks on the continuous rise,
people need to understand and learn ways to prevent from these
attacks. Cyber-attack is an important factor to be considered if one is
to be able to protect oneself from malicious attacks. Without proper
security measures, most computer technology would hinder home
users more than such technologies would help. Knowledge of how
cyber-attacks operate and protective steps that can be taken to reduce
chances of its occurrence are key to increasing these security
measures. The purpose of this paper is to inform home users on the
importance of identifying and taking preventive steps to avoid cyberattacks.
Throughout this paper, many aspects of cyber-attacks will be
discuss: what a cyber-attack is, the affects of cyber-attack for home
users, different types of cyber-attacks, methodology to prevent such
attacks; home users can take to fortify security of their computer.
Abstract: In this paper, we have compared and analyzed the
electroabsorption properties between with and without excitonic
effect bulk in high purity GaAs spatial light modulator for optical
fiber communication network. The eletroabsorption properties such
as absorption spectra, change in absorption spectra, change in
refractive index and extinction ration has been calculated. We have
also compared the result of absorption spectra and change in
absorption spectra with the experimental results and found close
agreement with experimental results.
Abstract: Load modeling is one of the central functions in
power systems operations. Electricity cannot be stored, which means
that for electric utility, the estimate of the future demand is necessary
in managing the production and purchasing in an economically
reasonable way. A majority of the recently reported approaches are
based on neural network. The attraction of the methods lies in the
assumption that neural networks are able to learn properties of the
load. However, the development of the methods is not finished, and
the lack of comparative results on different model variations is a
problem. This paper presents a new approach in order to predict the
Tunisia daily peak load. The proposed method employs a
computational intelligence scheme based on the Fuzzy neural
network (FNN) and support vector regression (SVR). Experimental
results obtained indicate that our proposed FNN-SVR technique gives
significantly good prediction accuracy compared to some classical
techniques.
Abstract: The inherent skin patterns created at the joints in the
finger exterior are referred as finger knuckle-print. It is exploited to
identify a person in a unique manner because the finger knuckle print
is greatly affluent in textures. In biometric system, the region of
interest is utilized for the feature extraction algorithm. In this paper,
local and global features are extracted separately. Fast Discrete
Orthonormal Stockwell Transform is exploited to extract the local
features. Global feature is attained by escalating the size of Fast
Discrete Orthonormal Stockwell Transform to infinity. Two features
are fused to increase the recognition accuracy. A matching distance is
calculated for both the features individually. Then two distances are
merged mutually to acquire the final matching distance. The
proposed scheme gives the better performance in terms of equal error
rate and correct recognition rate.
Abstract: This study evaluated the use of raw or processed
Prosopis juliflora (Meskit) pods as a major ingredient in a formulated
ration to provide an alternative non-conventional concentrate for
livestock feeding in Oman. Dry Meskit pods were reduced to lengths
of 0.5- 1.0 cm to ensure thorough mixing into three diets. Meskit
pods were subjected to two types of treatments; roasting and soaking.
They were roasted at 150оC for 30 minutes using a locally-made
roasting device (40 kg barrel container rotated by electric motor and
heated by flame gas cooker). Chopped pods were soaked in tap water
for 24 hours and dried for 2 days under the sun with frequent turning.
The Meskit-pod-based diets (MPBD) were formulated and pelleted
from 500 g/kg ground Meskit pods, 240 g/kg wheat bran, 200 g/kg
barley grain, 50 g/kg local dried sardines and 10 g/kg of salt. Twenty
four 10 months-old intact Omani male lambs with average body
weight of 27.3 kg (± 0.5 kg) were used in a feeding trial for 84 days.
They were divided (on body weight basis) and allocated to four diet
combination groups. These were: Rhodes grass hay (RGH) plus a
general ruminant concentrate (GRC); RGH plus raw Meskit pods
(RMP) based concentrate; RGH plus roasted Meskit pods (ROMP)
based concentrate; RGH plus soaked Meskit pods (SMP) based
concentrate Daily feed intakes and bi-weekly body weights were
recorded. MPBD had higher contents of crude protein (CP), acid
detergent fibre (ADF) and neutral detergent fibre (NDF) than the
GRC. Animals fed various types of MPBD did not show signs of ill
health. There was a significant effect of feeding ROMP on the
performance of Omani sheep compared to RMP and SMP. The
ROMP fed animals had similar performance to those fed the GRC in
terms of feed intake, body weight gain and feed conversion ratio
(FCR).This study indicated that roasted Meskit pods based diet may
be used instead of the commercial concentrate for feeding Omani
sheep without adverse effects on performance. It offers a cheap
alternative source of protein and energy for feeding Omani sheep.
Also, it might help in solving the spread impact of Meskit trees,
maintain the ecosystem and helping in preserving the local tree
species.
Abstract: Qatar, a Gulf country highly dependent on its oil and
gas revenues – is looking to innovate, diversify, and ultimately reach
its aim of creating a knowledge economy to prepare for its post-oil
era. One area that the country is investing in is Contemporary Art,
and world renowned artists such as Damien Hirst and Richard Serra –
have been commissioned to design site-specific art for the public
spaces of the city of Doha as well as in more remote desert locations.
This research discusses the changing presence, role and context of
public art in Doha, both from a historical and cultural overview, and
the different forms and media as well as the typologies of urban and
public spaces in which the art is installed. It examines the process of
implementing site-specific artworks, looking at questions of scale,
history, social meaning and formal aesthetics. The methodologies
combine theoretical research on the understanding of public art and
its role and placement in public space, as well as empirical research
on contemporary public art projects in Doha, based on documentation
and interviews and as well as site and context analysis of the urban or
architectural spaces within which the art is situated. Surveys and
interviews – using social media - in different segments of the
contemporary Qatari society, including all nationalities and social
groups, are used to measure and qualify the impacts and effects on
the population.
Abstract: In this paper, we propose an intelligent system that is
used for monitoring the health conditions of patients. Monitoring the
health condition of patients is a complex problem that involves
different medical units and requires continuous monitoring especially
in rural areas because of inadequate number of available specialized
physicians. The proposed system will improve patient care and drive
costs down comparing to the existing system in Jordan. The proposed
system will be the start point to faster and improve the
communication between different units in the health system in
Jordan. Connecting patients and their physicians beyond hospital
doors regarding their geographical area is an important issue in
developing the health system in Jordan. The ability of making
medical decisions, the quality of medical is expected to be improved.
Abstract: In this investigation, we have evaluated the effects of
arsenic trioxide on hepatic function in pregnant and lactating Swiss
albino mice and their suckling pups. Experiments were carried out on
female mice given 175 ppm As2O3 in their drinking water from the
14th day of pregnancy until day 14 after delivery. Our results showed
a significant decrease in plasma levels of total protein and albumin,
cholesterol and triglyceride in As2O3 treated mice and their pups. The
hyperbilirubinemia and the increased plasma total alkaline
phosphatase activity suggested the presence of cholestasis.
Transaminase activities as well as lactate deshydrogenase activity in
plasma, known as biomarkers of hepatocellular injury, were elevated
indicating hepatic cells’ damage after treatment with As2O3.
Exposure to arsenic led to an increase of liver thiobarbituric acid
reactive substances level along with a concomitant decrease in the
activities of superoxide dismutase, catalase and glutathione
peroxidase and in glutathione.
Abstract: Cell volume, together with membrane potential and
intracellular hydrogen ion concentration, is an essential biophysical
parameter for normal cellular activity. Cell volumes can be altered by
osmotically active compounds and extracellular tonicity.
In this study, a simple mathematical model of osmotically induced
cell swelling and shrinking is presented. Emphasis is given to water
diffusion across the membrane. The mathematical description of the
cellular behavior consists in a system of coupled ordinary differential
equations. We compare experimental data of cell volume alterations
driven by differences in osmotic pressure with mathematical
simulations under hypotonic and hypertonic conditions. Implications
for a future model are also discussed.
Abstract: To achieve reliable welds with minimum distortion for
the fabrication of components in aerospace industry laser beam
welding is attempted. Laser welding can provide a significant benefit
for the welding of Titanium and Aluminium thin sheet alloys of its
precision and rapid processing capability. For laser welding, pulse
shape, energy, duration, repetition rate and peak power are the most
important parameters that influence directly the quality of welds. In
this experimental work for joining 1mm thick TI6AL4V and AA2024
alloy and JK600 Nd:YAG pulsed laser units used. The distortions at
different welding power and speed of titanium and aluminium thin
sheet alloys are investigated. Test results reveal that increase in
welding speed increases distortion in weldment
Abstract: The practice of freeing monuments from subsequent
additions crosses the entire history of conservation and it is
traditionally connected to the aim of valorisation, both for cultural
and educational purpose and recently even for touristic exploitation.
Defence heritage has been widely interested by these cultural and
technical moods from philological restoration to critic innovations. A
renovated critical analysis of Italian episodes and in particular the
Sardinian case of the area of San Pancrazio in Cagliari, constitute an
important lesson about the limits of this practice and the uncertainty
in terms of results, towards the definition of a sustainable good
practice in the restoration of military architectures.