Abstract: This paper presents a new method to detect high impedance faults in radial distribution systems. Magnitudes of third and fifth harmonic components of voltages and currents are used as a feature vector for fault discrimination. The proposed methodology uses a learning vector quantization (LVQ) neural network as a classifier for identifying high impedance arc-type faults. The network learns from the data obtained from simulation of a simple radial system under different fault and system conditions. Compared to a feed-forward neural network, a properly tuned LVQ network gives quicker response.
Abstract: Beginning from the creator of integro-differential
equations Volterra, many scientists have investigated these
equations. Classic method for solving integro-differential
equations is the quadratures method that is successfully applied up
today. Unlike these methods, Makroglou applied hybrid methods
that are modified and generalized in this paper and applied to the
numerical solution of Volterra integro-differential equations. The
way for defining the coefficients of the suggested method is also
given.
Abstract: The supported Pd catalysts were analyzed by X-ray
diffraction and X-ray absorption spectroscopy in order to determine
their global and local structure. The average particle size of the
supported Pd catalysts was determined by X-ray diffraction method.
One of the main purposes of the present contribution is to focus on
understanding the specific role of the Pd particle size determined by
X-ray diffraction and that of the support oxide. Based on X-ray
absorption fine structure spectroscopy analysis we consider that the
whole local structure of the investigated samples are distorted
concerning the atomic number but the distances between atoms are
almost the same as for standard Pd sample. Due to the strong
modifications of the Pd cluster local structure, the metal-support
interface may influence the electronic properties of metal clusters
and thus their reactivity for absorption of the reactant molecules.
Abstract: This study investigated the removal efficiency of electrokinetic remediation of copper-contaminated soil at different combinations of enhancement reagents used as anolyte and catholyte. Sodium hydroxide (at 0.1, 0.5, and 1.0 M concentrations) and distilled water were used as anolyte, while lactic acid (at 0.01, 0.1, and 0.5 M concentrations), ammonium citrate (also at 0.01, 0.1, and 0.5 M concentrations) and distilled water were used as catholyte. A continuous voltage application (1.0 VDC/cm) was employed for 240 hours for each experiment. The copper content of the catholyte was determined at the end of the 240-hour period. Optimization was carried out with a Response Surface Methodology - Optimal Design, including F test, and multiple comparison method, to determine which pair of anolyte-catholyte was the most significant for the removal efficiency. "1.0 M NaOH" was found to be the most significant anolyte while it was established that lactic acid was the most significant type of catholyte to be used for the most successful electrokinetic experiments. Concentrations of lactic acid should be at the range of 0.1 M to 0.5 M to achieve maximum percent removal values.
Abstract: The purpose of this paper is to discuss the influence of
resistance characteristic on the high conductive concrete considering
the various voltage and environment. The four-electrode method is
applied to the tailor-made high conductive concrete with appropriate
proportion. The curve of resistivity with the changes of voltage and
environment is plotted and the changes of resistivity are explored. The
result based on the methods reveals that resistivity is less affected by
the temperature factor, and the four-electrode method would be an
applicable measurement method on a site inspection.
Abstract: This research deals with investigations on the “Active
Generator" under rotor speed variations and output frequency
control. It runs at turbine speed and it is connected to a three phase
electrical power grid which has its own frequency different from
turbine frequency. In this regard the set composed of a four phase
synchronous generator and a natural commutated matrix converter
(NCMC) made with thyristors, is called active generator. It replaces a
classical mechanical gearbox which introduces many drawbacks. The
main idea in this article is the presentation of frequency control at
grid side when turbine runs at variable speed. Frequency control has
been done by linear and step variations of the turbine speed. Relation
between turbine speed (frequency) and main grid zero sequence
voltage frequency is presented.
Abstract: We present new finite element methods for Helmholtz and Maxwell equations on general three-dimensional polyhedral meshes, based on domain decomposition with boundary elements on the surfaces of the polyhedral volume elements. The methods use the lowest-order polynomial spaces and produce sparse, symmetric linear systems despite the use of boundary elements. Moreover, piecewise constant coefficients are admissible. The resulting approximation on the element surfaces can be extended throughout the domain via representation formulas. Numerical experiments confirm that the convergence behavior on tetrahedral meshes is comparable to that of standard finite element methods, and equally good performance is attained on more general meshes.
Abstract: This paper describes a 2.4 GHz passive switch mixer
and a 5/2.5 GHz voltage-controlled negative Gm oscillator (VCO)
with an inversion-mode MOS varactor. Both circuits are implemented
using a 1P8M 0.13 μm process. The switch mixer has an input
referred 1 dB compression point of -3.89 dBm and a conversion
gain of -0.96 dB when the local oscillator power is +2.5 dBm.
The VCO consumes only 1.75 mW, while drawing 1.45 mA from a
1.2 V supply voltage. In order to reduce the passives size, the VCO
natural oscillation frequency is 5 GHz. A clocked CMOS divideby-
two circuit is used for frequency division and quadrature phase
generation. The VCO has a -109 dBc/Hz phase noise at 1 MHz
frequency offset and a 2.35-2.5 GHz tuning range (after the frequency
division), thus complying with ZigBee requirements.
Abstract: Anodizing is an electrochemical process that converts the metal surface into a decorative, durable, corrosion-resistant, anodic oxide finish. Aluminum is ideally suited to anodizing, although other nonferrous metals, such as magnesium and titanium, also can be anodized. The anodic oxide structure originates from the aluminum substrate and is composed entirely of aluminum oxide. This aluminum oxide is not applied to the surface like paint or plating, but is fully integrated with the underlying aluminum substrate, so cannot chip or peel. It has a highly ordered, porous structure that allows for secondary processes such as coloring and sealing. In this experimental paper, we focus on a reliable method for fabricating nanoporous alumina with high regularity. Starting from study of nanostructure materials synthesize methods. After that, porous alumina fabricate in the laboratory by anodization of aluminum oxide. Hard anodization processes are employed to fabricate the nanoporous alumina using 0.3M oxalic acid and 90, 120 and 140 anodized voltages. The nanoporous templates were characterized by SEM and FFT. The nanoporous templates using 140 voltages have high ordered. The pore formation, influence of the experimental conditions on the pore formation, the structural characteristics of the pore and the oxide chemical reactions involved in the pore growth are discuss.
Abstract: Solution of some practical problems is reduced to the
solution of the integro-differential equations. But for the numerical
solution of such equations basically quadrature methods or its
combination with multistep or one-step methods are used. The
quadrature methods basically is applied to calculation of the integral
participating in right hand side of integro-differential equations. As
this integral is of Volterra type, it is obvious that at replacement with
its integrated sum the upper limit of the sum depends on a current
point in which values of the integral are defined. Thus we receive the
integrated sum with variable boundary, to work with is hardly.
Therefore multistep method with the constant coefficients, which is
free from noted lack and gives the way for finding it-s coefficients is
present.
Abstract: In this paper the optimal control strategy for
Permanent Magnet Synchronous Motor (PMSM) based drive system
is presented. The designed full optimal control is available for speed
operating range up to base speed. The optimal voltage space-vector
assures input energy reduction and stator loss minimization,
maintaining the output energy in the same limits with the
conventional PMSM electrical drive. The optimal control with three
components is based on the energetically criteria and it is applicable
in numerical version, being a nonrecursive solution. The simulation
results confirm the increased efficiency of the optimal PMSM drive.
The properties of the optimal voltage space vector are shown.
Abstract: An on chip low drop out voltage regulator that
employs elegant compensation scheme is presented in this paper. The
novelty in this design is that the device parasitic capacitances are
exploited for compensation at different loads. The proposed LDO is
designed to provide a constant voltage of 1.2V and is implemented in
UMC 180 nano meter CMOS technology. The voltage regulator
presented improves stability even at lighter loads and enhances line
and load regulation.
Abstract: This paper presents a comparison between two Pulse
Width Modulation (PWM) algorithms applied to a three-level Neutral
Point Clamped (NPC) Voltage Source Inverter (VSI). The first
algorithm applied is the triangular-sinusoidal strategy; the second is
the Space Vector Pulse Width Modulation (SVPWM) strategy. In the
first part, we present a topology of three-level NCP VSI. After that,
we develop the two PWM strategies to control this converter. At the
end the experimental results are presented.
Abstract: In this paper, based on steady-state models of Flexible
AC Transmission System (FACTS) devices, the sizing of static
synchronous series compensator (SSSC) controllers in transmission
network is formed as an optimization problem. The objective of this
problem is to reduce the transmission losses in the network. The
optimization problem is solved using particle swarm optimization
(PSO) technique. The Newton-Raphson load flow algorithm is
modified to consider the insertion of the SSSC devices in the
network. A numerical example, illustrating the effectiveness of the
proposed algorithm, is introduced. In addition, a novel model of a 3-
phase voltage source converter (VSC) that is suitable for series
connected FACTS a controller is introduced. The model is verified
by simulation using Power System Blockset (PSB) and Simulink
software.
Abstract: With the rapid advanced of technology, the industrial processes become increasingly demanding, from the point of view, power quality and controllability. The advent of multi levels inverters responds partially to these requirements. But actually, the new generation of multi-cells inverters permits to reach more performances, since, it offers more voltage levels. The disadvantage in the increase of voltage levels by the number of cells in cascades is on account of series igbts synchronisation loss, from where, a limitation of cells in cascade to 4. Regarding to these constraints, a new topology is proposed in this paper, which increases the voltage levels of the three-cell inverter from 4 to 8; with the same number of igbts, and using less stored energy in the flaying capacitors. The details of operation and modelling of this new inverter structure are also presented, then tested thanks to a three phase induction motor. KeywordsFlaying capacitors, Multi-cells inverter, pwm, switchers, modelling.
Abstract: Where renewable energy sources, solar, hydro, wind are available the remote communities and businesses can be provided with the most reliable and affordable source of electrical energy. This paper presents a model of safari rest contains all the necessary services for the interested tourists who visit the safari Sinai desert. The PV energy system provides the rural energy needs of remote communities. A photovoltaic renewable energy system is designed to feed the global Ac and Dc electrical required load of this safari rest . The benefits of photovoltaic renewable energy at rural applications are its versatility and convenience. This model of safari rest must be taken in consideration by Egyptian Government as it will provide the tourism plane by new interested tourism field which put a big spot on Red sea area: El Ghordaka.
Abstract: To judge whether the memristor can be interpreted as
the fourth fundamental circuit element, we propose a variable-relation
criterion of fundamental circuit elements. According to the criterion,
we investigate the nature of three fundamental circuit elements and the
memristor. From the perspective of variables relation, the memristor
builds a direct relation between the voltage across it and the current
through it, instead of a direct relation between the magnetic flux and
the charge. Thus, it is better to characterize the memristor and the
resistor as two special cases of the same fundamental circuit element,
which is the memristive system in Chua-s new framework. Finally, the
definition of memristor is refined according to the difference between
the magnetic flux and the flux linkage.
Abstract: Active power filter continues to be a powerful tool to control harmonics in power systems thereby enhancing the power quality. This paper presents a fuzzy tuned PID controller based shunt active filter to diminish the harmonics caused by non linear loads like thyristor bridge rectifiers and imbalanced loads. Here Fuzzy controller provides the tuning of PID, based on firing of thyristor bridge rectifiers and variations in input rms current. The shunt APF system is implemented with three phase current controlled Voltage Source Inverter (VSI) and is connected at the point of common coupling for compensating the current harmonics by injecting equal but opposite filter currents. These controllers are capable of controlling dc-side capacitor voltage and estimating reference currents. Hysteresis Current Controller (HCC) is used to generate switching signals for the voltage source inverter. Simulation studies are carried out with non linear loads like thyristor bridge rectifier along with unbalanced loads and the results proved that the APF along with fuzzy tuned PID controller work flawlessly for different firing angles of non linear load.
Abstract: A measurement system was successfully fabricated to
detect ion concentrations (hydrogen and chlorine) in this study.
PIC18F4520, the microcontroller was used as the control unit in the
measurement system. The measurement system was practically used
to sense the H+ and Cl- in different examples, and the pH and pCl
values were exhibited on real-time LCD display promptly. In the study,
the measurement method is used to judge whether the response voltage
is stable. The change quantity is smaller than 0.01%, that the present
response voltage compares with next response voltage for H+
measurement, and the above condition is established only 6 sec.
Besides, the change quantity is smaller than 0.01%, that the present
response voltage compares with next response voltage for Clmeasurement,
and the above condition is established only 5 sec.
Furthermore, the average error quantities would also be considered,
and they are 0.05 and 0.07 for measurements of pH and pCl values,
respectively.
Abstract: The investigation results of high-density hydrogen
heating by high-current electric arc are presented at initial pressure
from 5 MPa to 160 MPa with current amplitude up to 1.6 MA and
current rate of rise 109-1011 A/s. When changing the initial pressure
and current rate of rise, channel temperature varies from several
electronvolts to hundreds electronvolts. Arc channel radius is several
millimeters. But the radius of the discharge chamber greater than the
radius of the arc channel on approximately order of magnitude. High
efficiency of gas heating is caused by radiation absorption of
hydrogen surrounding the arc. Current channel consist from vapor of
the initiating wire. At current rate of rise of 109 A/s and relatively
small current amplitude gas heating occurs due to radiation
absorption in the band transparency of hydrogen by the wire vapours
with photon energies less than 13.6 eV. At current rate of rise of
1011 A/s gas heating is due to hydrogen absorption of soft X-rays
from discharge channel.