Abstract: Photoplethysmography is a simple measurement of the
variation in blood volume in tissue. It detects the pulse signal of heart
beat as well as the low frequency signal of vasoconstriction and
vasodilation. The transmission type measurement is limited to only a
few specific positions for example the index finger that have a short
path length for light. The reflectance type measurement can be
conveniently applied on most parts of the body surface. This study
analyzed the factors that determine the quality of reflectance
photoplethysmograph signal including the emitter-detector distance,
wavelength, light intensity, and optical properties of skin tissue.
Light emitting diodes (LEDs) with four different visible
wavelengths were used as the light emitters. A phototransistor was
used as the light detector. A micro translation stage adjusts the
emitter-detector distance from 2 mm to 15 mm.
The reflective photoplethysmograph signals were measured on
different sites. The optimal emitter-detector distance was chosen to
have a large dynamic range for low frequency drifting without signal
saturation and a high perfusion index. Among these four wavelengths,
a yellowish green (571nm) light with a proper emitter-detection
distance of 2mm is the most suitable for obtaining a steady and reliable
reflectance photoplethysmograph signal
Abstract: As a part of an evaluation system for R&D programs,
the Korean Government has applied the preliminary feasibility study
to new government R&D program plans. Basically, the fundamental purpose of the preliminary feasibility study is to decide that the
government will either do or do not invest in a new R&D Program. Additionally, the preliminary feasibility study can contribute to the
improvement of R&D program plans. For example, 2 cases of new
R&D program plans applied to the study are explained in this paper and there are expectations that these R&D programs would yield better
performance than without the study. It is thought that the important point of the preliminary feasibility study is not only the effective
decision making process of R&D program but also the opportunity to improve R&D program plan actually.
Abstract: In this paper, the 1-D conduction-radiation problem is solved by the lattice Boltzmann method. The effects of various parameters such as the scattering albedo, the conduction–radiation parameter and the wall emissivity are studied. In order to check on the accuracy of the numerical technique employed for the solution of the considered problem, the present numerical code was validated with the published study. The found results are in good agreement with those published
Abstract: Safety Health and Environment Code of Practice (SHE
COP) was developed to help road transportation operators to manage
its operation in a systematic and safe manner. A study was conducted
to determine the effectiveness of SHE COP implementation during
non-OPS period. The objective of the study is to evaluate the
implementations of SHE COP among bus operators during wee hour
operations. The data was collected by completing a set of checklist
after observing the activities during pre departure, during the trip, and
upon arrival. The results show that there are seven widely practiced
SHE COP elements. 22% of the buses have average speed exceeding
the maximum permissible speed on the highways (90 km/h), with
13% of the buses were travelling at the speed of more than 100 km/h.
The statistical analysis shows that there is only one significant
association which relates speeding with prior presence of
enforcement officers.
Abstract: Turbulent forced convection flow in a 2-dimensional channel over periodic grooves is numerically investigated. Finite volume method is used to study the effect of turbulence model. The range of Reynolds number varied from 10000 to 30000 for the ribheight to channel-height ratio (B/H) of 2. The downstream wall is heated by a uniform heat flux while the upstream wall is insulated. The investigation is analyzed with different types of nanoparticles such as SiO2, Al2O3, and ZnO, with water as a base fluid are used. The volume fraction is varied from 1% to 4% and the nanoparticle diameter is utilized between 20nm to 50nm. The results revealed 114% heat transfer enhancement compared to the water in a grooved channel by using SiO2 nanoparticle with volume fraction and nanoparticle diameter of 4% and 20nm respectively.
Abstract: Deep cold rolling (DCR) is a cold working process, which easily produces a smooth and work-hardened surface by plastic deformation of surface irregularities. In the present study, the influence of main deep cold rolling process parameters on the surface roughness and the hardness of AISI 4140 steel were studied by using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in terms of identifying the predominant factor amongst the selected parameters, their order of significance and setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. It was found that the ball diameter, rolling force, initial surface roughness and number of tool passes are the most pronounced parameters, which have great effects on the work piece-s surface during the deep cold rolling process. A simple, inexpensive and newly developed DCR tool, with interchangeable collet for using different ball diameters, was used throughout the experimental work presented in this paper.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: Global environmental changes lead to increased frequency and scale of natural disaster, Taiwan is under the influence of global warming and extreme weather. Therefore, the vulnerability was increased and variability and complexity of disasters is relatively enhanced. The purpose of this study is to consider the source and magnitude of hazard characteristics on the tourism industry. Using modern risk management concepts, integration of related domestic and international basic research, this goes beyond the Taiwan typhoon disaster risk assessment model and evaluation of loss. This loss evaluation index system considers the impact of extreme weather, in particular heavy rain on the tourism industry in Taiwan. Consider the extreme climate of the compound impact of disaster for the tourism industry; we try to make multi-hazard risk assessment model, strategies and suggestions. Related risk analysis results are expected to provide government department, the tourism industry asset owners, insurance companies and banking include tourist disaster risk necessary information to help its tourism industry for effective natural disaster risk management.
Abstract: The main aim of this study was to examine whether
people understand indicative conditionals on the basis of syntactic
factors or on the basis of subjective conditional probability. The
second aim was to investigate whether the conditional probability of
q given p depends on the antecedent and consequent sizes or derives
from inductive processes leading to establish a link of plausible cooccurrence
between events semantically or experientially associated.
These competing hypotheses have been tested through a 3 x 2 x 2 x 2
mixed design involving the manipulation of four variables: type of
instructions (“Consider the following statement to be true", “Read the
following statement" and condition with no conditional statement);
antecedent size (high/low); consequent size (high/low); statement
probability (high/low). The first variable was between-subjects, the
others were within-subjects. The inferences investigated were Modus
Ponens and Modus Tollens. Ninety undergraduates of the Second
University of Naples, without any prior knowledge of logic or
conditional reasoning, participated in this study.
Results suggest that people understand conditionals in a syntactic
way rather than in a probabilistic way, even though the perception of
the conditional probability of q given p is at least partially involved in
the conditionals- comprehension. They also showed that, in presence
of a conditional syllogism, inferences are not affected by the
antecedent or consequent sizes. From a theoretical point of view these
findings suggest that it would be inappropriate to abandon the idea
that conditionals are naturally understood in a syntactic way for the
idea that they are understood in a probabilistic way.
Abstract: This study applied the Gaussian trajectory
transfer-coefficient model (GTx) to simulate the particulate matter
concentrations and the source apportionments at Nanzih Air Quality
Monitoring Station in southern Taiwan from November 2007 to
February 2008. The correlation coefficient between the observed and
the calculated daily PM10 concentrations is 0.5 and the absolute bias of
the PM10 concentrations is 24%. The simulated PM10 concentrations
matched well with the observed data. Although the emission rate of
PM10 was dominated by area sources (58%), the results of source
apportionments indicated that the primary sources for PM10 at Nanzih
Station were point sources (42%), area sources (20%) and then upwind
boundary concentration (14%). The obvious difference of PM10 source
apportionment between episode and non-episode days was upwind
boundary concentrations which contributed to 20% and 11% PM10
sources, respectively. The gas-particle conversion of secondary
aerosol and long range transport played crucial roles on the PM10
contribution to a receptor.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: One of the most challengeable issues in ESL
(Electronic System Level) design is the lack of a general modeling
scheme for on chip communication architecture. In this paper some
of the mostly used methodologies for modeling and representation of
on chip communication are investigated. Our goal is studying the
existing methods to extract the requirements of a general
representation scheme for communication architecture synthesis. The
next step, will be introducing a modeling and representation method
for being used in automatically synthesis process of on chip
communication architecture.
Abstract: In order to study of hydropriming and halopriming on
germination and early growth stage of wheat (Triticum aestivum) an
experiment was carried out in laboratory of the Department of
Agronomy and Plant breeding, Shahrood University of Technology.
Seed treatments consisted of T1: control (untreated seeds), T2:
soaking in distilled water for 18 h (hydropriming). T3: soaking in -
1.2 MPa solution of CaSO4 for 36 h (halopriming). Germination and
early seedling growth were studied using distilled water (control) and
under osmotic potentials of -0.4, -0.8 and -1.2 MPa for NaCl and
polyethylene glycol (PEG 6000), respectively. Results showed that
Hydroprimed seeds achieved maximum germination seedling dry
weight, especially during the higher osmotic potentials. Minimum
germination was recorded at untreated seeds (control) followed by
osmopriming. Under high osmotic potentials, hydroprimed seeds had
higher GI (germination index) as compared to haloprimed or
untreated seeds. Interaction effect of seed treatment and osmotic
potential significantly affected the seedling vigour index (SVI).
Abstract: This research aims to study the preferable tourism and
the elements of choosing tourist destination from domestic tourist in
Bangkok and the nearby areas in Thailand.The data were collected by
using 1249 set of questionnaires, in mid-August 2012. The result
illustrates that religious destinations are the most preferable places
for the tourist. The average expense per travel is approximately 47
USD a time. Travellers travel based on the advertisement in the
television and internet and their decisions is based on the reputation
of the destinations.
The result on a place dimension demonstrates the neatness and
well managed location play a crucial role on tourist destination.
Gender, age, marriage status and their origins are affecting their
spending and travelling behaviour. The researcher reckon that
providing the area of arcade, selling the souvenir and promoting
tourism among a young professional group would be an important
key follow the income distribution policy, including managing the
destination to welcome the family group, which the result is to
identified as the highest spending.
Abstract: The purpose of this study is to suggest energy efficient
routing for ad hoc networks which are composed of nodes with limited
energy. There are diverse problems including limitation of energy
supply of node, and the node energy management problem has been
presented. And a number of protocols have been proposed for energy
conservation and energy efficiency. In this study, the critical point of
the EA-MPDSR, that is the type of energy efficient routing using only
two paths, is improved and developed. The proposed TP-MESR uses
multi-path routing technique and traffic prediction function to increase
number of path more than 2. It also verifies its efficiency compared to
EA-MPDSR using network simulator (NS-2). Also, To give a
academic value and explain protocol systematically, research
guidelines which the Hevner(2004) suggests are applied. This
proposed TP-MESR solved the existing multi-path routing problem
related to overhead, radio interference, packet reassembly and it
confirmed its contribution to effective use of energy in ad hoc
networks.
Abstract: In this paper, we study FPGA implementation of a
novel supra-optimal receiver diversity combining technique,
generalized maximal ratio combining (GMRC), for wireless
transmission over fading channels in SIMO systems. Prior
published results using ML-detected GMRC diversity signal
driven by BPSK showed superior bit error rate performance to
the widely used MRC combining scheme in an imperfect
channel estimation (ICE) environment. Under perfect channel
estimation conditions, the performance of GMRC and MRC
were identical. The main drawback of the GMRC study was
that it was theoretical, thus successful FPGA implementation
of it using pipeline techniques is needed as a wireless
communication test-bed for practical real-life situations.
Simulation results showed that the hardware implementation
was efficient both in terms of speed and area. Since diversity
combining is especially effective in small femto- and picocells,
internet-associated wireless peripheral systems are to
benefit most from GMRC. As a result, many spinoff
applications can be made to the hardware of IP-based 4th
generation networks.
Abstract: To study the performance of soybean (Glycine max L.) cultivars in varying weeding regimes, a field experiment was conducted in 2010. The experiment was split plot in a randomized complete block design with 3 replicates. The four cultivars and two lines of soybean including: Sahar, Hill, Sari, Telar, 032 and 033 in main plot and weeding regime consist of no weeding (control), one weeding (35 days after planting) and two weeding (35+20 days after planting) were randomized in sub plot. In weed infested plots inevitably had the highest yield reduction in all varieties. On the other hand, plots weeded twice showed the best performance for all cultivars and lines. Although 033 had the highest yield over weeding regimes, but Hill was the best cultivar in suppression of weeds, which indicated the competitiveness of this cultivar. Double weeding, with the use of competitive soybean cultivars would be an effective approach for producing yield.
Abstract: Polyurethane foams (PUF) has been prepared from
vegetable; soybean based polyols. They were characterized into
flexible and semi rigid polyurethane foam. This work is directed to
production of flexible polyurethane foams by a process involving the
reaction of mixture of 2,4- and 2,6-Toluene di Isocyanate isomers,
with portion of to blends of soy polyols with petroleum polyol in the
presence of other ingredients such as blowing agents, silicone
surfactants and accelerating agents. Additon of chain extender
improves the property then further decreases the properties on further
addition of the same. The objective of this work was to study the
effect of chain extender and role of phosphoric acid catalyst to the
final properties and correlate the morphology image with mechanical
properties of these foams.
Abstract: A comparative evaluation of acute toxicity of
synthesized nano silvers using two different procedures (biological
and chemical reduction methods) and silver ions on bacteria
Vibrio fischeri was investigated. The bacterial light inhibition test as
a toxicological endpoint was used by applying of a homemade
luminometer. To compare the toxicity effects as a quantitative
parameter, a nominal effective concentrations (EC) of chemicals and
a susceptibility constant (Z-value) of bacteria, after 5 min and 30 min
exposure times, were calculated. After 5 and 30 min contact times,
the EC50 values of two silver nanoparticles and the EC20 values were
about similar. It demonstrates that toxicity of silvers was independent
of their procedure. The EC values of nanoparticles were larger than
those of the silver ions. The susceptibilities(Z- Values) of V.fischeri
(L/mg) to the silver ions were greater than those of the nano silvers.
According to the EC and Z values, the toxicity of silvers decreased in
the following order: Silver ions >> silver nanoparticles from
chemical reduction method ~ silver nanoparticles from biological
method.
Abstract: The objective of the research is to study and compare
response surface designs: Central composite designs (CCD), Box-
Behnken designs (BBD), Small composite designs (SCD), Hybrid
designs, and Uniform shell designs (USD) over sets of reduced models
when the design is in a spherical region for 3 and 4 design variables.
The two optimality criteria ( D and G ) are considered which larger
values imply a better design. The comparison of design optimality
criteria of the response surface designs across the full second order
model and sets of reduced models for 3 and 4 factors based on the
two criteria are presented.