Abstract: Cerebellar ataxia is a steadily progressive
neurodegenerative disease associated with loss of motor control,
leaving patients unable to walk, talk, or perform activities of daily
living. Direct motor instruction in cerebella ataxia patients has limited
effectiveness, presumably because an inappropriate closed-loop
cerebellar response to the inevitable observed error confounds motor
learning mechanisms. Could the use of EEG based BCI provide
advanced biofeedback to improve motor imagery and provide a
“backdoor” to improving motor performance in ataxia patients? In
order to determine the feasibility of using EEG-based BCI control in
this population, we compare the ability to modulate mu-band power
(8-12 Hz) by performing a cued motor imagery task in an ataxia
patient and healthy control.
Abstract: The chemical and physical characteristics of rainwater
harvested from a typical rooftop were progressively studied. The
samples of rainwater collected were analyzed for pH, major ion
concentrations, TDS, turbidity, conductivity. All the Physicochemical
constituents fell within the WHO guideline limits at some points as
rainfall progresses except the pH. All the components of rainwater
quality measured during the study showed higher concentrations
during the early stages of rainfall and reduce as time progresses.
There was a downward trend in terms of pH as rain progressed, with
18% of the samples recording pH below the WHO limit of 6.5-8.0. It
was observed that iron concentration was above the WHO threshold
value of 0.3 mg/l on occasions of heavy rains. The results revealed
that most of physicochemical characteristics of rainwater samples
were generally below the WHO threshold, as such, the rainwater
characteristics showed satisfactory conditions in terms of
physicochemical constituents.
Abstract: We present a refined multiscale Shannon entropy for
analyzing electroencephalogram (EEG), which reflects the underlying
dynamics of EEG over multiple scales. The rationale behind
this method is that neurological signals such as EEG possess
distinct dynamics over different spectral modes. To deal with the
nonlinear and nonstationary nature of EEG, the recently developed
empirical mode decomposition (EMD) is incorporated, allowing a
decomposition of EEG into its inherent spectral components, referred
to as intrinsic mode functions (IMFs). By calculating the Shannon
entropy of IMFs in a time-dependent manner and summing them over
adaptive multiple scales, it results in an adaptive subscale entropy
measure of EEG. Simulation and experimental results show that
the proposed entropy properly reveals the dynamical changes over
multiple scales.
Abstract: Roles of the vegetation to mitigate the erosion of the
stream bed or to facilitate the deposition of the fine sediments by the
species of the aquatic plants were presented. Field investigation on the
estimation of the change of the bed level and the estimation of the flow
characteristics were performed. The results showed that Phragmites
japonica has the mitigation function of 0.3m-0.4m of the erosion in the
range of higher than 1.0m/s of flow velocity at the vegetated region.
Phragmites communis has the mitigation function of 0.2m-0.3m of the
erosion in the range of higher than 0.7m/s of flow velocity at the
vegetated region. Salix gracilistyla has greater role than Phragmites
japonica and Phragmites communis to sustain the stable channel. It
has the mitigation function of 0.4m-0.5m of the erosion in the range of
higher than 1.4m/s of flow velocity. Miscanthus sacchariflorus has a
weak role compared with that of Phragmites japonica and Salix
gracilistyla, but it has still function for sustaining the stable bed. From
these results, the vegetation has effective roles to mitigate the erosion
or to facilitate the deposition of the stream bed.
Abstract: The addition of lime as Ca(OH)2 to sewage sludge to
destroy pathogens (Escherichia coli), was evaluated also in relation
to heavy metal bioavailability.
The obtained results show that the use of calcium hydroxide at the
dose of 3% effectively destroyed pathogens ensuring the stability at
high pH values over long period and the duration of the sewage
sludge stabilization. In general, lime addition decreased the total
extractability of heavy metals indicating a reduced bioavailability of
these elements. This is particularly important for a safe utilization in
agricultural soils to reduce the possible transfer of heavy metals to
the food chain.
Abstract: Rapid growth of Information Technologies (IT) has
had huge influence on enterprises, and it has contributed to its
promotion and increasingly extensive use in enterprises. Information
Technologies have to a large extent determined the processes taking
place in an enterprise; what is more, IT development has brought the
need to adopt a brand new approach to human resources management
in an enterprise. The use of IT in human resource management
(HRM) is of high importance due to the growing role of information
and information technologies. The aim of this paper is to evaluate the
use of information technologies in human resources management in
enterprises. These practices will be presented in the following areas:
recruitment and selection, development and training, employee
assessment, motivation, talent management, personnel service.
Results of conducted survey show diversity of solutions applied in
particular areas of human resource management. In the future, further
development in this area should be expected, as well as integration of
individual HRM areas, growing mobile-enabled HR processes and
their transfer into the cloud. Presented IT solutions applied in HRM
are highly innovative, which is of great significance due to their
possible implementation in other enterprises.
Abstract: In this research, TRACE model of Chinshan BWR/4
nuclear power plant (NPP) has been developed for the simulation and
analysis of ultimate response guideline (URG).The main actions of
URG are the depressurization and low pressure water injection of
reactor and containment venting. This research focuses to verify the
URG efficiency under Fukushima-like conditions. TRACE analysis
results show that the URG can keep the PCT below the criteria
1088.7 K under Fukushima-like conditions. It indicated that Chinshan
NPP was safe.
Abstract: Froth flotation remains to date as one of the most used
metallurgical processes for concentrating metal-bearing minerals in
ores. Oxide ores are relatively less amenable to froth flotation and
require a judicious choice of reagents for the recovery of metals to be
optimised. Laboratory batch flotation tests were conducted to
determine the effect of two types of gasoil-rinkalore mixtures on the
flotation response of a copper cobalt oxide ore sample. The head
assay conducted on the initial ore sample showed that it contained
about 2.90% of Cu, 0.12% of Co.
Upon the flotation test work, the results obtained indicated that the
concentrate obtained with use of the mixture gazoil-rinkalore RX
yielded 8.24% Cu and 0.22% Co concentrate grades with recoveries
of 76.0% Cu and 78.0% Co respectively. But, the concentrate
obtained by use of the mixture gazoil-rinkalore RX3 yielded
relatively bad results with 5.92% Cu and 0.18% Cu concentrate
grades with recoveries of 70.3% Cu and 65.3% Co respectively.
Abstract: Software fault prediction models are created by using
the source code, processed metrics from the same or previous version
of code and related fault data. Some company do not store and keep
track of all artifacts which are required for software fault prediction.
To construct fault prediction model for such company, the training
data from the other projects can be one potential solution. Earlier we
predicted the fault the less cost it requires to correct. The training
data consists of metrics data and related fault data at function/module
level. This paper investigates fault predictions at early stage using the
cross-project data focusing on the design metrics. In this study,
empirical analysis is carried out to validate design metrics for cross
project fault prediction. The machine learning techniques used for
evaluation is Naïve Bayes. The design phase metrics of other projects
can be used as initial guideline for the projects where no previous
fault data is available. We analyze seven datasets from NASA
Metrics Data Program which offer design as well as code metrics.
Overall, the results of cross project is comparable to the within
company data learning.
Abstract: The Speexx results revealed four main factors
affecting the success of 190 Thai sophomores as follows: 1) Future
English training should be pursued in applied Speexx development.
2) Thai students didn’t see the benefit of having an Online Language
Training Program. 3) There is a great need to educate the next
generation of learners on the benefits of Speexx within the
community. 4) A great majority of Thai Sophomores didn't know
what Speexx was.
A guideline for self-reliance planning consisted of four aspects: 1)
Development planning: by arranging groups to further improve
English abilities with the Speexx Language Training program and
encourage using Speexx into every day practice. Local communities
need to develop awareness of the usefulness of Speexx and share the
value of using the program among family and friends. 2) Humanities
and Social Science staff should develop skills using this Online
Language Training Program to expand on the benefits of Speexx
within their departments. 3) Further research should be pursued on
the Thai Students progression with Speexx and how it helps them
improve their language skills with Business English. 4) University’s
and Language centers should focus on using Speexx to encourage
learning for any language, not just English.
Abstract: This paper presents the design and characterization of
analog readout interface circuits for ion sensitive field effect
transistor (ISFET) and ion selective electrode (ISE) based sensor.
These interface circuits are implemented using MIMOS’s 0.35um
CMOS technology and experimentally characterized under 24-leads
QFN package. The characterization evaluates the circuit’s
functionality, output sensitivity and output linearity. Commercial
sensors for both ISFET and ISE are employed together with glass
reference electrode during testing. The test result shows that the
designed interface circuits manage to readout signals produced by
both sensors with measured sensitivity of ISFET and ISE sensor are
54mV/pH and 62mV/decade, respectively. The characterized output
linearity for both circuits achieves above 0.999 Rsquare. The readout
also has demonstrated reliable operation by passing all qualifications
in reliability test plan.
Abstract: The concept of national security in Iran is a
permanently effective factor in acceptance or rejection of many
international obligations. These obligations had been defined
according to the type of legislation of Iran in many aspects.
Therefore, there are several treaties at international level which
requires Iran’s security to come in contact with obligations in these
treaties in a way that an obstacle to join to them and their passage in
parliament. This issue is a typical category which every country pays
attention to be accepted in treaties or to include their national
security in that treaties and also they can see the related treaties from
this perspective, but this issue that 'what is the concept of Iran’s
national security', and 'To what extent it is changed in recent years,
especially after Islamic Revolution' are important issues that can be
criticized. Thus, this study is trying to assess singed treaties from the
perspective of Iran’s national security according of the true meaning
of treaty and to investigate how the international treaties may be in
conflict with Iran’s national security.
Abstract: In educational technology, the idea of innovation is
usually tethered to contemporary technological inventions and
emerging technologies. Yet, using long-known technologies in ways
that are pedagogically or experimentially new can reposition them as
emerging educational technologies. In this study we explore how a
subtle pivot in pedagogical thinking led to an innovative education
technology. We describe the design and implementation of an online
writing tool that scaffolds students in the evaluation of their own
informational texts. We think about how pathways to innovation can
emerge from pivots, namely a leveraging of longstanding practices in
novel ways has the potential to cultivate new opportunities for
learning. We first unpack Infowriter in terms of its design, then we
describe some results of a study in which we implemented an
intervention which included our designed application.
Abstract: There are many perceived advantages of microwave
ablation have driven researchers to develop innovative antennas to
effectively treat deep-seated, non-resectable hepatic tumors. In this
paper a coaxial antenna with a miniaturized sleeve choke has been
discussed for microwave interstitial ablation therapy, in order to
reduce backward heating effects irrespective of the insertion depth
into the tissue. Two dimensional Finite Element Method (FEM) is
used to simulate and measure the results of miniaturized sleeve choke
antenna. This paper emphasizes the importance of factors that can
affect simulation accuracy, which include mesh resolution, surface
heating and reflection coefficient. Quarter wavelength choke
effectiveness has been discussed by comparing it with the unchoked
antenna with same dimensions.
Abstract: While emerging technologies continue to emerge,
research into their use in learning contexts often focuses on a subset
of educational practices and ways of using technologies. In this study
we begin to explore the extent to which educational designs are
influenced by larger societal and education-related factors not usually
explicitly considered when designing or identifying technology-supported
education experiences for research study. We examine
patterns within and between factors via a content analysis across ten
years and 19 different journals of published peer-reviewed research
on technology-supported writing. Our findings have implications for
how researchers, designers, and educators approach technology-supported
educational design within and beyond the field of writing
and literacy.
Abstract: The article proposed intends to analyze the possibility
(and conditions) of a media regulation law in a democratic rule of law
in the twenty-first century. To do so, will be presented initially the
idea of the public sphere (by Jürgen Habermas), showing how it is
presented as an interface between the citizen and the state (or the
private and public) and how important is it in a deliberative
democracy. Based on this paradigm, the traditional perception of the
role of public information (such as system functional element) and on
the possibility of media regulation will be exposed, due to the public
nature of their activity. A critical argument will then be displayed
from two different perspectives: a) the formal function of the current
media information, considering that the digital age has fragmented
the information access; b) the concept of a constructive democracy,
which reduces the need for representation, changing the strategic
importance of the public sphere. The question to be addressed (based
on the comparative law) is if the regulation is justified in a
polycentric democracy, especially when it operates under the digital
age (with immediate and virtual communication). The proposal is to
be presented in the sense that even in a twenty-first century the media
in a democratic rule of law still has an extremely important role and
may be subject to regulation, but this should be on terms very
different (and narrower) from those usually defended.
Abstract: White concrete facade elements are widely used in
construction industry. It is challenging to achieve the desired
workability in casting of white concrete elements. Particle Matrix
model was used for proportioning the self-compacting white concrete
(SCWC) to control segregation and bleeding and to improve
workability. The paper presents how to reach the target slump flow
while controlling bleeding and segregation in SCWC. The amount of
aggregates, binders and mixing water, as well as type and dosage of
superplasticizer (SP) to be used are the major factors influencing the
properties of SCWC. Slump flow and compressive strength tests were
carried out to examine the performance of SCWC, and the results
indicate that the particle matrix model could produce successfully
SCWC controlling segregation and bleeding.
Abstract: Microstructural and electrical properties of
Cu-chromium alloy (Cu-Cr) dispersed with vapor-grown carbon fiber
(VGCF) prepared by powder metallurgy (P/M) process have been
investigated. Cu-0.7 mass% Cr pre-alloyed powder (Cu-Cr) made by
water atomization process was used as raw materials, which contained
solid solute Cr elements in Cu matrix. The alloy powder coated with
un-bundled VGCF by using oil coating process was consolidated at
1223 K in vacuum by spark plasma sintering, and then extruded at
1073 K. The extruded Cu-Cr alloy (monolithic alloy) had 209.3 MPa
YS and 80.4 IACS% conductivity. The extruded Cu-Cr with 0.1
mass% VGCF composites revealed a small decrease of YS compared
to the monolithic Cu-Cr alloy. On the other hand, the composite had a
higher electrical conductivity than that of the monolithic alloy. For
example, Cu-Cr with 0.1 mass% VGCF composite sintered for 5 h
showed 182.7 MPa YS and 89.7 IACS% conductivity. In the case of
Cu-Cr with VGCFs composites, the Cr concentration was observed
around VGCF by SEM-EDS analysis, where Cr23C6 compounds were
detected by TEM observation. The amount of Cr solid solution in the
matrix of the Cu-Cr composites alloy was about 50% compared to the
monolithic Cu-Cr sintered alloy, and resulted in the remarkable
increment of the electrical conductivity.
Abstract: To ensure student success in a non-majors biology course, a flipped classroom pedagogical approach was developed and implemented. All students were assigned online lectures to listen to before they come to class. A three hour lecture was split into one hour of online component, one hour of in class lecture and one hour of worksheets done by students in the classroom. This deviation from a traditional 3 hour in class lecture has resulted in increased student interest in science as well as better understanding of difficult scientific concepts. A pre and post survey was given to measure the interest in the subject and grades were used to measure the success rates. While the overall grade average did not change dramatically, students reported a much better appreciation of biology. Also, students overwhelmingly like the use of worksheets in class to help them understand the concepts. They liked the fact that they could listen to lectures at their own pace on line and even repeat if needed. The flipped classroom approach turned out to work really well our non-science majors and the author is ready to implement this in other classrooms.
Abstract: The aim of this study is to investigate formability of
Al based closed cell metallic foams at high temperature. The foam
specimens with rectangular section were produced from
AlMg1Si0.6TiH20.8 alloy preform material. Bending and free
bending tests based on gravity effect were applied to foam specimens
at high temperatures. During the tests, the time-angular deformation
relationships with various temperatures were determined.
Deformation types formed in cell walls were investigated by means
of Scanning Electron Microscopy (SEM) and optical microscopy.
Bending deformation about 90° was achieved without any defect at
high temperatures. The importance of a critical temperature and
deformation rate was emphasized in maintaining the deformation.
Significant slip lines on surface of cell walls at tensile zones of
bending specimen were observed. At high strain rates, the microcrack
formation in boundaries of elongated grains was determined.