Abstract: Copper being one of the major intrinsic residual
impurities in steel possesses the tendency to induce severe
microstructural distortions if not controlled within certain limits.
Hence, this paper investigates the effect of this element on the
mechanical properties of construction steel with a view to ascertain
its safe limits for effective control. The experiment entails collection
of statistically scheduled samples of hot rolled profiles with varied
copper concentrations in the range of 0.12-0.39 wt. %. From these
samples were prepared standard test specimens subjected to tensile,
impact, hardness and microstructural analyses. Results show a rather
huge compromise in mechanical properties as the specimens
demonstrated 54.3%, 74.2% and 64.9% reduction in tensile strength,
impact energy and hardness respectively as copper content increases
from 0.12 wt. % to 0.39 wt. %. The steel’s abysmal performance is
due to the severe distortion of the microstructure occasioned by the
development of incoherent complex compounds which weaken the
pearlite reinforcing phase. It is concluded that the presence of copper
above 0.22 wt. % is deleterious to construction steel performance.
Abstract: Mass flow measurement is the basis of most technoeconomic
formulations in the chemical industry. This calls for
reliable and accurate detection of mass flow. Flow measurement
laboratory experiments were conducted using various instruments.
These consisted of orifice plates, various sized rotameters, wet gas
meter and soap bubble meter. This work was aimed at evaluating
appropriate operating conditions and accuracy of the aforementioned
devices. The experimental data collected were compared to
theoretical predictions from Bernoulli’s equation and calibration
curves supplied by the instrument’s manufacturers. The results
obtained showed that rotameters were more reliable for measuring
high and low flow rates; while soap-bubble meters and wet-gas
meters were found to be suitable for measuring low flow rates. The
laboratory procedures and findings of the actual work can assist
engineering students and professionals in conducting their flow
measurement laboratory test work.
Abstract: The discarded clam shell waste, fossil and edible oil
as biolubricant feedstocks create environmental impacts and food
chain dilemma, thus this work aims to circumvent these issues by
using activated saltwater clam shell waste (SCSW) as solid catalyst
for conversion of Jatropha curcas oil as non-edible sources to ester
biolubricant. The characterization of solid catalyst was done by
Differential Thermal Analysis-Thermo Gravimetric Analysis (DTATGA),
X-Ray Fluorescence (XRF), X-Ray Diffraction (XRD),
Brunauer-Emmett-Teller (BET), Field Emission Scanning Electron
Microscopy (FESEM) and Fourier Transformed Infrared
Spectroscopy (FTIR) analysis. The calcined catalyst was used in the
transesterification of Jatropha oil to methyl ester as the first step, and
the second stage was involved the reaction of Jatropha methyl ester
(JME) with trimethylolpropane (TMP) based on the various process
parameters. The formated biolubricant was analyzed using the
capillary column (DB-5HT) equipped Gas Chromatography (GC).
The conversion results of Jatropha oil to ester biolubricant can be
found nearly 96.66%, and the maximum distribution composition
mainly contains 72.3% of triester (TE).
Abstract: An anthropometric study applied to 1,115 students of
the Faculty of Chemical Sciences and Engineering of the
Autonomous University of California. Thirteen individual
measurements were taken in a sitting position. The results obtained
allow forming a reliable anthropometric database for statistical
studies and analysis and inferences of specific distributions, so the
opinion of experts in occupational medicine recommendations may
emit to reduce risks resulting in an alteration of the vital signs during
the execution of their school activities. Another use of these analyses
is to use them as a reliable reference for future deeper research, to the
design of spaces, tools, utensils, workstations, with anthropometric
dimensions and ergonomic characteristics suitable to use.
Abstract: This paper presents an anthropometric study
conducted to 300 employees in a maquiladora industry that belongs
to the cluster of medical products as part of a research project to
pretend simulate workplace conditions under which operators
conduct their activities. This project is relevant because traditionally
performed a study to design ergonomic workspaces according to
anthropometric profile of users, however, this paper demonstrates the
importance of making decisions when the infrastructure cannot be
adapted for economic whichever put emphasis on user activity.
Abstract: Economic Dispatch (ED) is one of the most
challenging problems of power system since it is difficult to determine
the optimum generation scheduling to meet the particular load demand
with the minimum fuel costs while all constraints are satisfied. The
objective of the Economic Dispatch Problems (EDPs) of electric
power generation is to schedule the committed generating units
outputs so as to meet the required load demand at minimum operating
cost while satisfying all units and system equality and inequality
constraints. In this paper, an efficient and practical steady-state genetic
algorithm (SSGAs) has been proposed for solving the economic
dispatch problem. The objective is to minimize the total generation
fuel cost and keep the power flows within the security limits. To
achieve that, the present work is developed to determine the optimal
location and size of capacitors in transmission power system where,
the Participation Factor Algorithm and the Steady State Genetic
Algorithm are proposed to select the best locations for the capacitors
and determine the optimal size for them.
Abstract: No matter how much perfect we become in our
practical skills regarding the implementation of learned ideas, the
need of technical writing capability cannot be neglected being a
professional. Technical writing is a way of communicating the ideas
in written which otherwise need to be presented orally. Technical
writing skills have always been the need of the time, as they are
required for internal as well as external official communication in
both formal and informal manner. Moreover, they are the best way to
capture the attention of your customers by presenting information in
effective manner. This paper aims to analyze the importance of
technical writing skills in professional industries of Pakistan by
conducting a survey. Survey results presented in this paper clearly
depicts the importance of formal and informal written communication
media used in different professional industries in Pakistan. Analysis
and discussion of the extent to which the alternative ways of
communication besides technical writing have got importance in
Pakistan is also an important aspect of this survey.
Abstract: Historical and ancestral bonds of the countries in the
Middle East have led to similarities in culture and context of their
societies. In addition, economical resources, such as the oil industry,
have generally been an integrative point in the region. Higher
education of a country is influenced by different national and
international factors and, regarding the mentioned bonds, it is inviting
to study the development of the countries of the Middle East in
higher education and draw some practical implications which can be
used in the educational policymaking of the region. This review
includes a data analysis on the population of international students in
the countries of the Middle East. As its second objective, a review
study on the successful countries, that is, those which host the highest
number of international students, and the strategies they have
developed to reach this state among the countries of the region, has
been conducted. Suggestions are made as to the strategies in higher
education systems of these countries which could prove useful and
practical in the development of internationalization of higher
education in the region, specifically with regard to the recruitment of
international students.
Abstract: Ficus deltoidea from the Moraceae family is a popular
medicinal herb in Malaysia. It possesses strong antioxidant and antiinflammatory
properties. In the present study, the anti-inflammatory
effects of F. deltoidea extract on UVB-irradiated HaCaT
Keratinocytes were investigated. HaCaT Keratinocytes were UVBirradiated
(12.5 mJ/cm3) and were treated with 0.05, 0.08 or 0.1% of
F. deltoidea extract. Cell viability following UVB irradiation was
significantly higher in the groups treated with the F. deltoidea extract
at doses of 0.05, 0.08 or 0.1% than in control group with UVB
irradiation only. Tumor necrosis factor-α (TNF-α), interleukin-1α
(IL-1α), interleukin-6 (IL-6) and cyclooxygenase (COX-2) play
primary roles in the inflammation process upon UV irradiation and
are known to be stimulated by UVB irradiation. Treatment with the
F. deltoidea extract dramatically inhibited the UV-induced TNF-α,
IL-1α, IL-6, and COX-2 expression. These results suggest that the F.
deltoidea extract inhibits the production of pro-inflammatory
cytokines and may be an effective protective agent for the treatment
of skin diseases.
Abstract: This entry concerned with dense silica bricks
microstructure was produced as a part of a project within the
Technology Agency of the Czech Republic which is being
implemented in cooperation of the biggest producer of refractories
the P-D Refractories CZ company with the research organisation
Brno University of Technology. The paper is focused on the
influence of mixture homogenisation and the influence of grain size
of the mineraliser on the resulting utility properties of the material as
well as its microstructure. It has a decisive influence on the durability
of the material in a building structure. This paper is a continuation of
a previously published study dealing with the suitability of various
types of mineralising agents in terms of density, strength and mineral
composition of silica brick.
The entry describes the influence of the method of mixture
homogenisation and the influence of granulometry of the applied Femineralising
agent on the resulting silica microstructure. Porosity,
density, phase composition and microstructure of the experimentally
prepared silica bricks samples were examined and the results were
discussed in context with the technology of homogenisation and
firing temperature used. The properties of silica bricks samples were
compared to the sample without any Fe-mineraliser.
Abstract: A circularly polarized fractal boundary microstrip
antenna is presented. The sides of a square patch along x- axis, yaxis
are replaced with Minkowski and Koch curves correspondingly.
By using the fractal curves as edges, asymmetry in the structure is
created to excite two orthogonal modes for circular polarization (CP)
operation. The indentation factors of the fractal curves are optimized
for pure CP. The simulated results of the novel polyfractal antenna
are demonstrated.
Abstract: Nanotechnology is the new cyber, according to several major leaders in this field. Just as cyber is entrenched across global society now, nano is poised to be major capabilities enabler of the next decades. Expert members from the National Nanotechnology Initiative (in U.S.) representing government and science disciplines say nano has great significance for the military and the general public. It is predicted that after next 15 years nanotechnology will replace information technology as the most economic technology platform. Nanotechnology has even wider applications than information technology.
Abstract: Rice straw pellets are a promising fuel as a renewable
energy source. Financial analysis is needed to make a utilization
system using rise straw pellets financially feasible, considering all
regional conditions including stakeholders related to the collection and
storage, production, transportation and heat utilization. We conducted
the financial analysis of feasibility for a heat utilization system using
rice straw pellets which has been developed for the first time in
Nanporo, Hokkaido, Japan. Especially, we attempted to clarify the
effect of factors required for the system to be financial feasibility, such
as the heating energy demand and collection and storage method of
rice straw. The financial feasibility was found to improve when
increasing the heating energy demand and collecting wheat straw in
August separately from collection of rice straw in November because
the costs of storing rice straw and producing pellets were reduced.
However, the system remained financially unfeasible. This study
proposed a contractor program funded by a subsidy from Nanporo
local government where a contracted company, instead of farmers,
collects and transports rice straw in order to ensure the financial
feasibility of the system, contributing to job creation in the region.
Abstract: Cognitive Radio is a turning out technology that
empowers viable usage of the spectrum. Energy Detector-based
Sensing is the most broadly utilized spectrum sensing strategy.
Besides, it's a lot of generic as receivers doesn't would like any
information on the primary user's signals, channel data, of even the
sort of modulation. This paper puts forth the execution of energy
detection sensing for AM (Amplitude Modulated) signal at 710 KHz,
FM (Frequency Modulated) signal at 103.45 MHz (local station
frequency), Wi-Fi signal at 2.4 GHz and WiMAX signals at 6 GHz.
The OFDM/OFDMA based WiMAX physical layer with
convolutional channel coding is actualized utilizing USRP N210
(Universal Software Radio Peripheral) and GNU Radio based
Software Defined Radio (SDR). Test outcomes demonstrated the
BER (Bit Error Rate) augmentation with channel noise and BER
execution is dissected for different Eb/N0 (the energy per bit to noise
power spectral density ratio) values.
Abstract: The aim of this paper is to analyze the ability to
identify and acquire knowledge from external sources at the regional
level in the Czech Republic. The results show that the most important
sources of knowledge for innovative activities are sources within the
businesses themselves, followed by customers and suppliers.
Furthermore, the analysis of relationships between the objective of
the innovative activity and the ability to identify and acquire
knowledge implies that knowledge obtained from (1) customers aims
at replacing outdated products and increasing product quality; (2)
suppliers aims at increasing capacity and flexibility of production;
and (3) competing businesses aims at growing market share and
increasing the flexibility of production and services. Regions should
therefore direct their support especially into development and
strengthening of networks within the value chain.
Abstract: This paper deals with the issue of biomass and sorted
municipal waste gasification and cogeneration using hot-air turbo-set.
It brings description of designed pilot plant with electrical output 80
kWe. The generated gas is burned in secondary combustion chamber
located beyond the gas generator. Flue gas flows through the heat
exchanger where the compressed air is heated and consequently
brought to a micro turbine. Except description, this paper brings our
basic experiences from operating of pilot plant (operating parameters,
contributions, problems during operating, etc.). The principal
advantage of the given cycle is the fact that there is no contact
between the generated gas and the turbine. So there is no need for
costly and complicated gas cleaning which is the main source of
operating problems in direct use in combustion engines because the
content of impurities in the gas causes operation problems to the units
due to clogging and tarring of working surfaces of engines and
turbines, which may lead as far as serious damage to the equipment
under operation. Another merit is the compact container package
making installation of the facility easier or making it relatively more
mobile. We imagine, this solution of cogeneration from biomass or
waste can be suitable for small industrial or communal applications,
for low output cogeneration.
Abstract: The article demonstrates on a case study how it is
possible to identify MSD risk. It is based on a dissertation Risk
identification model of occupational diseases formation in relation to
the work activity that determines what risk can endanger workers who
are exposed to the specific risk factors. It is evaluated based on
statistical calculations. These risk factors are main cause of upperextremities
musculoskeletal disorders.
Abstract: This research is aimed to develop the online-class
scheduling management system and improve as a complex problem
solution, this must take into consideration in various conditions and
factors. In addition to the number of courses, the number of students
and a timetable to study, the physical characteristics of each class
room and regulations used in the class scheduling must also be taken
into consideration. This system is developed to assist management in
the class scheduling for convenience and efficiency. It can provide
several instructors to schedule simultaneously. Both lecturers and
students can check and publish a timetable and other documents
associated with the system online immediately. It is developed in a
web-based application. PHP is used as a developing tool. The
database management system was MySQL. The tool that is used for
efficiency testing of the system is questionnaire. The system was
evaluated by using a Black-Box testing. The sample was composed
of 2 groups: 5 experts and 100 general users. The average and the
standard deviation of results from the experts were 3.50 and 0.67.
The average and the standard deviation of results from the general
users were 3.54 and 0.54. In summary, the results from the research
indicated that the satisfaction of users were in a good level.
Therefore, this system could be implemented in an actual workplace
and satisfy the users’ requirement effectively.
Abstract: This paper explores competencies that managers of
small firms in Ghana use to enhance operational flexibility towards
the attainment of higher productivity. This is because the requisite
competence required of such managers to be effective performers
continues to be a challenge. Data was collected from managers of
three hundred small firms using a standardized self-completion
questionnaire and analyzed using the Amos-based structural equation
model approach. Findings from factor and confirmatory factor
analyses showed that the only competence exhibited by managers
toward effective performance is realistic practices evident at the
workplace. It is concluded that a manager’s self-confidence and
involvement in areas that he/she is good at, and his/her possession of
skills that enables performance at high capacity are indications of the
manger’s effectiveness. The study outcome provides a knowledge
base helpful to policy-makers, especially in Ghana, in determining
the requisite managerial competences required by small firm
managers for effective performance.
Abstract: Nowadays, the amounts of companies which tend to
have an Enterprise Resource Planning (ERP) application are
increasing. Although ERP projects are expensive, time consuming,
and complex, there are some successful experiences. These days,
developing countries are striving to implement ERP projects
successfully; however, there are many obstacles. Therefore, these
projects would be failed or partially failed. This paper concerns the
implementation of a successful ERP implementation, IFS, in Iran at
Dana Geophysics Company (DGC). After a short review of ERP and
ERP market in Iran, we propose a three phases deployment
methodology (phase 1: Preparation and Business Process
Management (BPM) phase 2: implementation and phase 3: testing,
golive-1 (pilot) and golive-2 (final)). Then, we present five guidelines
(Project Management, Change Management, Business Process
Management (BPM), Training& Knowledge Management, and
Technical Management), which were chose as work streams. In this
case study we present lessons learned in Project management and
Business process Management.